Search Documents

By Terry S. Cory

This report describes the results of a measurement program to determine the broad spectral characteristics of both differential and common mode noise on phone lines in three coal mines; and, signal attenuation spectral characteristics on the same broad basis over phone line strings with taps/branches. The frequency range used was baseband -1000 Hz for resolution bandwidth ranging from 100 Hz near baseband to 30 KHz near I MHz. The signal attenuation measurements were performed on all three "legs" of taps where possible and applicable. Results were obtained comparing shielded and unshielded phone lines In one mine. The results include an improved electromagnetic noise chart for coal mines showing variations with types of mines, topology, and location of noise sources; also, fundamental high-frequency limit on untreated phone lines in coal mines is identified

Jan 1, 1981

By Michael Rieber

A new mode of coal transportation based on the principles of pneumatic conveying has been recently, proposed by Soo, et al. [5]. Pneumatic transport is not a novel concept and commercial experience with pneumatic pipelines for short haul distances is plentiful. The list of applications is long and includes transporting ores, chemicals and pharmaceutical products, agricultural products, and domestic and industrial wastes. The study by Soo, et al. [5] updated an earlier one [l0] and presented the most recent economic evaluation of pneumatic transportation of coal. Their preliminary study concluded that there are immediate advantages for short-distance transport (less than 100 miles) and that it is both technologically and economically feasible. That study also concludes that pneumatic transport has a higher potential and more promising profitability in long-distance applications than rail if new track and roadbed must be built. Some of the advantages of long and short distance pneumatic pipeline transport of coal compared to rail and slurry transport are: 1) Replacement of diesel fuel consumed by unit trains, as the pipeline can be powered by coal-generated electricity; 2) Reduction of the skilled-labor costs required for upgrading and maintaining railroads; 3) Elimination of signaling, rerouting and overpass costs due to increased rail traffic on' mainline trackage;

Jan 1, 1977

By K-H. Frohne

This report presents a study of the Cooper sand of the Fork Run pool of Warren and McKean Counties, Pa., and a prediction of the secondary oil recovery by gasflooding the reservoir. A computer program employing a modification of the Craig, Geffen, and Morse secondary recovery calculation was used to make the gas flood performance forecast and is presented in the appendix. The Cooper sand reservoir in the Fork Run pool lies at a depth of about 1,900 feet and covers an area 1/2 mile wide by 2-1/4 miles long. Original oil in place is estimated to have been 8,266,000 STB. The primary recovery mechanism is solution gas drive, and ultimate primary recovery may reach 20 percent over a well life of 90 years. Two computer predictions were made for gas flooding the Cooper reservoir. The first was for a 25-acre pilot five-spot utilizing existing wells, but project economics were poor since only 25 percent of injection gas is utilized for pilot oil recovery. Recovery was 71,000 STB, or 22 percent of oil in place at flood initiation, but required 25,700 scf gas injected per STB of oil recovered. In the second prediction, pilot area performance was projected for the entire Fork Run pool, and economics became good. Recovery was 1,753,000 STB from 25 five-spots after the injection of only 6,400 scf per STB of oil recovered.

Jan 1, 1969

By G. L. Oldright

"The various districts in the United States where complex lead-zinc ores occur are too well known to require description, there being hardly a mining State with any large amount of ores of either metal that is free from this problem. This paper briefly presents developments in the volatilization process, as applied to the treatment of such ores, since the data in Bureau of Mines Bulletin 211** were published. In that bulletin, among the many types of ore treated, examples are given of the treatment of lead-zinc ores by the chloride volatilization process for the separation of lead. An outline of the general process, with views of the rotary kiln, ore feeder, firing system (these three features resemble closely those of cement-kiln practice), dust chambers, and a Cottrell precipitator to remove the fume from the gas, are also shown in that bulletin, to which the reader is referred for the results obtained, and for practical details of operation. The small initial cost of a volatilization plant, and its adaptability for use in isolated districts were emphasized.In general, it was found that when an intensely oxidizing atmosphere was maintained in the furnace, a good lead-zinc separation could be made. Therefore, a heavy sulphide ore would have to be preroasted, and enough air would have to be admitted to obtain complete combustion of whatever fuel might be used.The work done by private companies and the bureau since the data for Bulletin 211 were obtained, indicates that the ores most immediately amenable to treatment by volatilization are of two types. The first is an oxidzed lead. silrer ore whose variable lime content makes it impractical to chloridize the ore for acidulated brine leaching, and whose base metal content makes treatment by cyanidattion unfeasible, The second type is the lead-zinc ore mentioned above, and is the one on which data are available for publication at present. This article Chows what ores of this latter type are amenable to treatment by volatilization, by giving briefly some of the more important physical and chemical properties an ore should preferably possess. Several examples are given from both laboratory experimental work, and from practice in the field, showing various phases of the volatilization process."

Nov 1, 1923

By Charles Sabine

The U.S. Bureau of Mines studied mines and prospects in the Bristol/Granite Mountains Wilderness Study Area (WSA) in 1982. The 45,000 acre WSA, located in the eastern Mojave Desert of California, is underlain by Mesozoic plutonic rocks with scattered roof pendants of Paleozoic (?) metasedimentary rocks. Two mines and six prospects are identified; one mine, the Silver Lode Mine, and a prospect of unknown name are adjacent to the area. The Silver Lode Mine has occurrences of silver, lead and zinc. Within the study area, the Comanche Mine has occurrences of iron and copper and the Iron Victory Prospect has an occurrence of iron. None are large enough to constitute a resource. Occurrences of magnesian marble at the Comanche Mine, Iron Victory Prospect, and elsewhere in the area contain too much MgO for commercial use other than agricultural soil supplements or crushed stone. Transportation costs to markets would exceed the value of the rock. At the Comanche Mine, situated in a roof pendant of marble, about 10 tons remain of a 110-ton pod of magnetite which contained 42.5% iron, and less than 50 tons remain of a mineralized fault breccia which averaged 2.5% copper and 0.3 oz/ton silver. Magnesian marble contained 41 to 45% CaO and 14 to 16% MgO. Primary and secondary silver, lead, zinc, and copper minerals are disseminated along altered joints and in quartz veins in quartz monzonite at the Silver Lode Mine, adjacent to the WSA. Analytical data are sporadic; samples contained as much as 0.12 oz/ton gold, 1.8 oz/ton Silver, 1.1% lead, 3.8% zinc, and 0.3% copper. Mineralized zones in the workings are not resources, but they might indicate possible silver-lead-zinc resources at depth. At the Iron Victory Prospect, lenses of magnetite and hematite with some chalcopyrite occur in a skarn lone in a marble roof pendant. About 110,000 tons of iron-rich rock, averaging 47.2% iron, are present; the largest lens contains about 30,000 tons. About 150,000 tons of magnesian marble, averaging 41.0% CaO and 11.7% MgO, are also present. Deposits of stone, and sand and gravel in the WSA are too distant from markets to be resources. Occurrences of energy minerals were not identified.

Jan 1, 1984

By C. E. Brechtel

A testing program was conducted to design a cemented backfill fur hydraulic placement in underhand cut and fill mining of a steeply dipping coal seam. The testing evaluated the use of three different backfill aggregates, locally available at the coal mine, with Portland cement and five different pozzolans, including a Class F fly ash, a Class C fly ash, a cement kiln dust and ground smelter slag. Both viscosity and uniaxial compressive strength of backfill mixtures with different pozzolan and Portland cement contents were used to evaluate their suitability. Based upon the results of preliminary testing, an optimum mixture of alluvial sand with six percent Portland cement and ten percent Class F pozzolan was chosen for further compression testing.

Jan 1, 1985

By David Schlain

The Bureau of Mines investigated methods for electrodepositing platinum-group metals from molten cyanide baths. The preparation of thick, protective coatings on molybdenum, Inconel, graphite, stainless steel, copper, and other structural metals were studied, as well as the electroforming of platinum and iridium crucibles. Iridium, rhodium, and ruthenium can be electrodeposited under an inert atmosphere, while platinum and palladium require the presence of air. Electrolytes may be prepared by direct-current electrolysis in NaCN or mixtures of NaCN and KCN using anodes of the particular platinum-group metal. When the concentration of metal increases to about 0.3 or 0.4 percent, the deposits become bright, adherent, and coherent. Current densities may be 10 to 25 ma/cm2, and plating rates are often 0.5 mil/hr. Platinum and palladium baths deteriorate because of the oxidation of cyanide to cyanate and carbonate, and the precipitation of metal. Changes in the platinum cyanide bath are relatively slow. The protection against oxidation afforded by the platinum-group metal coatings is evaluated by testing encapsulated specimens in a thermogravimetric balance. Surface pretreatment and the use of undercoats are discussed.

Jan 1, 1977

By Albert L. Toenges

A phase in strip mining of bituminous coal is the overturning of the surface of the land. The purpose of this report is to acquaint the operators and others interested in stripping with the work that has been done in certain States to reclaim the surface of land from which the coal has been removed by this method of raining. The preparation of this manuscript follows an extensive study of the subject in the field in the course of which a large number of strip mines were visited. ACKNOWLEDGMENT The information used in the report was obtained through the courtesy and cooperation of the operators of the mines visited, State officials and educational institutions, and others interested in the subject.

Jan 1, 1939

By James C. Barker

Unverified reports of rare earth element (REE) concentrations in gold placers and radioactive mineral prospects in the Zane Hills were investigated by the U.S. Bureau of Mines as part of the Alaska critical minerals program. REE is reported to occur in dredge concentrates at the Hogatza mine and up to 1.2 pct REE was previously analyzed in alkalic syenite (bostonite) dikes marginal to the pluton. In addition, numerous thorium-rich veins, explored for their uranium content but unevaluated for REE, occur on the western margin of the Zane Hills. The Bureau mapped and sampled all of the reported or suspected REE occurrences. Dredge concentrates contain abundant uranothorianite, a mineral species which incorporates cerium subgroup REE. Bostonite dikes occur in conjunction with a multi-phased zoned alkalic intrusion, however, no significant REE concentrations were found. Thorium-rich veins contain nil to 0.5 pct Y but resource potential is limited by this relatively low grade, the ultimate low tonnage potential, and the lack of uranium as a major economic element. The Zane Hills exhibit attractive exploration targets for uranium deposits, primarily in a sedimentary form. Gold may be found peripheral to the pluton in both placer and lode deposits. Resource potential of REE, however, appears limited to a placer by-product of REE-Zr-Ti that is recoverable only during large scale gold placer mining. Placer exploration of the lower Wheeler and Dakli Creeks is suggested.

Jan 1, 1991

By R. E. Zane

The Northwest Experiment Station of the Bureau of :,!in-s, in cooperation with the College of Mines, University of Washington, has completed a detailed investigation-of the physical and chemical properties of western cokes made or used in the Pacific Northwest, as evaluated by standard methods./ One of the properties determined, to which more or less importance has been attached, was reactivity5/ or combustibility. As no standardized procedure is available, it was necessary to develop a workable method for evaluating this property. The combustibility of coke is usually measured by the formation of carbon dioxide with time at a particular temperature or by the reduction of carbon dioxide to carbon monoxide. Analysis of the resulting gases commonly is required to evaluate the result. The method described in this paper is simple and direct in that the sample of coke or other carbonaceous material is weighed as it burns; the loss in weight and time is indicated by a balance and clock arrangement. Gas analyses are not required. Methods similar in principle have been used by Tu, Davis, and Hottel6/ and by Oshima and Fukuda7/ for determining the combustion rate of carbon and for studying the effect of ash on combustion characteristics. Both methods are more elaborate in procedure and apparatus required than that described here. Briefly, the method comprises burning a sample of coarsely grained coke or

Jan 1, 1940

By P. T. Brooks

Mineral nodules from the ocean floor represent a vast potential source of manganese, nickel, cobalt, and copper. Process development studies to devise methods for recovering these metals were conducted by the Bureau of Mines using two types of nodules--relatively low-grade calcareous nodules from the Atlantic Ocean and higher grade siliceous nodules from the Pacific Ocean. Ammoniacal carbonate leaching of reduced nodules appeared to have the best potential for processing the calcareous nodules, but the method proved to be impractical for recovering manganese. Extraction of 90 percent or better of the nickel, cobalt, and copper showed the technique to be attractive for recovery of these metals. The siliceous nodules appeared amenable to a process that starts with either a sulfur dioxide leach or a sulfation roast followed by a water leach to dissolve the soluble sulfates.

Jan 1, 1971

By R. V. Ramani, J. M. Mutmansky, P. C. Luna, V. A. Marple, Honglin He, B. A. Olson

The development of a sampling instrument for the assessment of an underground coal miner’s exposure to airborne respirable coal mine dust on a continuous and real-time basis has been long identified as essential for timely initiation of control actions. A respirable dust dosimeter (RDD) which operates on the principle of increasing pressure across a filter media with increasing dust mass on the filter has been developed by the National Institute for Occupational Safety and Health. Comparisons of the performance of the RDD with an U.S. approved gravimetric respirable dust sampler (GRD) have shown that the RDD may meet the requirements for measuring miners’ exposures on a cumulative, near real-time basis such as mid-shift and end of shift exposures. Recently, the performances of the RDD and GRD were compared by conducting side-by-side area sampling experiments in a controlled experimental environment in the laboratory and in underground coal mines under normal operating conditions. In this paper, the results from the in-mine study are presented and discussed. The experimental design for the in-mine study included two mines in different coal seams in different geographic coal regions. To ensure a wide range of concentrations, the experiments were conducted in a continuous miner section in Mine 1, and a longwall face in Mine 2. Airborne dust sampling was conducted for four different shifts at each mine. In each shift, two samples of different exposure durations were collected from two different locations. Each sample consisted of the readings of three dosimeters and the exposed filters from the three paired GRD samplers. As a result, a total of 96 comparative samples were obtained, 48 for each mine. The data were analyzed for the precision of the RDD and GRD measurements and for the relationships between the differential pressure of the RDD and the mass of dust on the paired GRD filter. The analyses indicate that, on the average, the RDD and the GRD track the airborne respirable dust concentrations well, exhibiting both a high correlation between the two measurements and a reliable predictive relationship of one from the other. Details of the experimental design, data analyses procedures, results, conclusions and recommendations of the underground experiments are presented in this paper.

By J. R. Thoenen

In June 1929 the Bureau of Mines issued a 13-page Information Circular entitled "Mineral wool." This was one of the first publications to present to the public some technical aspects of the mineral-wool industry. Since that time several articles have appeared on the subject in the technical press as well as publications by State organizations. Inquiries for information on mineral wool have continued to be received by the Bureau of Mines in large numbers, and in 1935 it was decided, with the cooperation of the is industry, to make a field survey of the plants then producing and to collect therefrom technical data to be compiled in a paper for public distribution. As a first step, a brief questionnaire was mailed to the known producers asking if they would cooperate for publication. Favorable replies were received from of percent of the manufacturers, and the field work was started. As the study progressed and tie number of plants visited grew, it became more and more apparent that the industry had made rapid strides in technical operation and control of their product, as well as in increasing production during the mast decade.

Jan 1, 1938

By Duane L. Abata

This work, conducted under Bureau of Mines contract, deals with the development of a computer graphics software package that will: 1. display mine ventilation schematics and other representative Illustrations for a real-time data acquisition system under development by the Bureau, and, 2. utilize the Bureau-owned Minefire and Ventilation Code for display of ventilation on and contamination predictions. The software package has been written try operate on a 64K, Z-80 based microprocessor-computer. The project has been divided into two phases. The first phase dealt with the development of the graphics software The sec rind phase dealt with the retrofit of the Minefire and Ventilation Code to the Z-80 microprocessor-computer.

Jan 1, 1984

By Louis Schaffer

The purposes of the research were to assess the applicability of new accident investigation methods to mining accidents, and to adapt those found to be applicable in the development of a new methodology for use in mining. The development included field testing, evaluation and modification of the new methodology. The report is in two volumes. Volume one discusses the background research, the design of a methodology for field evaluation, preliminary field tests in Utah mines, and work done to prepare for a formal, complete evaluation by federal government mine safety officials. This, volume 2, discusses the field evaluation done by the contractor and cooperating mines after the program was re-directed by the Bureau of Mines. It relates to research done during a period of approximately eighteen months, ending in April, 1983.

Jan 1, 1986

By Todd M. Ruff

The majority of fatalities that occur in road construction work zones in the United States involve a worker being struck by a piece of construction equipment or other vehicle. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health, in cooperation with the Washington State Department of Transportation, is evaluating methods to decrease these accidents. One such method uses devices that assist equipment operators in monitoring blind areas around the equipment to prevent collisions with workers on foot or other objects. Several cameras and sensor systems are available for this application, and a study was conducted to evaluate these systems on various trucks used in road construction and maintenance. Tests were conducted using sanding trucks during the winter months, which allowed researchers to investigate the effectiveness and limitations of various technologies under the most extreme conditions. Tests were also conducted using dump trucks during the warmer months to study the effectiveness of the systems in highway work zones. Results show that many difficulties arise when using camera and sensor systems in cold, snowy climates. And, while the operation of these systems is more reliable during the warmer months, challenges still exist in using them on equipment in crowded work areas.

Jan 1, 2004

By G. F. Kuncir

The analysis summarized herein evaluates the Bureau of Mines Program for Advancing Mining Technology Oil Shale in terms of the economic benefits which may be derived for the Nation as a result of its successful research and development efforts. On the basis of postulated oil shale production scenarios, benefit-cost ratio indicators are computed for the program elements as they apply to surface, underground, and modified in situ oil shale mining systems. Eight value indicators are used to measure the Program's beneficial impact on the future oil shale industry in relation to planned research and development costs. These are: capital cost savings, operating cost savings, labor savings, environmental quality maintenance cost reduction, reduction in production costs, byproduct production benefits, total production benefits, and additions to recoverable reserves. Program costs are aggregated from 1974 through 1987 and major benefits are accrued from 1982 through 2040. Both cost and benefit streams are discounted to mid-1975 present value.

Jan 1, 1977

By J. G. Donaldson

Optimum conditions are given for chloridizing pyrite, marcasite, chalcopyrite, arsenopyrite, stibnite, and covellite with chlorine gas. The formation of metal chlorides is affected by the time and temperature of chloridizing, and by particle size of the sample. Chloridizing data also are given for chemically precipitated antimony (III) sulfide and copper (II) sulfide.

Jan 1, 1962

By Joseph W. Horne

This report presents the results of an investigation by the U. S. Bureau of Mines in cooperation with the State of Colorado, on the yields and properties of oils produced from oil shale, lignite and subbituminous coal using the standard assay method developed by the Bureau for oil-shale testing,. The purpose of this work, which is part of the general study of oil shales being conducted by the Bureau of Mines and cooperating agencies, was to obtain information on the amount and character of the yield of crude oil or tar from different typical oil shales, the yield of light oil or naptha that might be suitable for use in motor fuels, and other products of shale oil. As the west has large resources both of oil shale and low-grade non-coking coals, it is of interest to know the relative yields of tars, light oils, and combustible gases that can be produced from these coals when retorted under conditions similar to those suited for oil-shale retorting. Source of Samples The coal samples were obtained from deposits on or adjacent to the public lands in the States of the Rocky Mountain region. Many of the mines sampled are operating under Government leases or permits. The number of coal samples secured from the various states are: Colorado, 6; Montana, 9; north Dakota, 6; New Mexico. 1; South Dakota, 1; Wyoming, 9. Of these samples, 14 were lignite coal, 16 subbituminous coal, and a bituminous coal. The standard channel method of the Bureau of Mines was used for sampling. Coal samples received at the Boulder Office weighed about twelve pounds each, and duplicate samples were sent to the Pittsburgh Station for proximate and ultimate analyses. The origin of the samples and description of the deposits are given in Table 1.

Jan 1, 1927

By R. G. Bottge

To better understand those factors which increase mining costs in Alaska, a Bureau of Mines study was conducted to compare the estimated costs of operating a 100,000-tpd open pit copper mine located on a hypothetical ore body in the Lake Clark area, Alaska, with the costs of mining a similarly sized hypothetical copper ore body near Tucson, Ariz. The information derived should be beneficial to the State and Federal governments in appraising the potential for development of large, low-grade porphyry copper deposits in south-central Alaska. Conventional mining and concentrating methods were assumed, and capital and operating costs were derived using flowsheets and standard costing methods. The total price required for copper mined in Alaska and Arizona was $1.12 and $0.63 per pound, respectively, plus or minus 20 percent. These values were obtained assuming no leaching of low-grade copper, recovery of gold, silver, and molybdenum as byproducts, 100-percent equity financing, and a 12 percent discounted cash flow rate of return. The average domestic and international prices for copper in July 1973 were $0.60 and $0.916 per pound, respectively. The existence of a developed transportation and power system in Alaska would have reduced capital and operating costs subs tantially. The required price for copper would have declined from $1.12 to $1.05 per pound, plus or minus 20 percent.

Jan 1, 1974