Search Documents

By Roger J. Morrell

Bureau of Mines laboratory experiments with reduced scale cutter and cutter forces were performed to (1) define the fundamental relationships governing disk cutter performance and (2) to develop a method of predicting disk cutter performance in soft, medium, and hard rocks. The rock cutting experiments were performed in four igneous and metamorphic rocks that ranged in compressive strength from 38,000 to 67,000 psi. A special testing machine called a linear cutter apparatus (LCA) was used to load and traverse a free rolling disk cutter across a smooth rock surface. Each pass of the disk produced a single crater, and runs were spaced to avoid breakage between craters. During each run the normal and tangential cutter forces were measured and recorded. The soft and medium rock data were obtained from previous Bureau experiments with disk cutters. Crater depth, tangential cutter force, crater volume, specific energy versus normal cutter force, and crater width versus depth are defined within this study. With the use of standard physical properties, performance prediction equations were developed using stepwise linear regression analysis techniques. A method of using these prediction equations to calculate the boring rate, the cutter spacing, and the torque and energy requirements of a full-scale boring machine was also developed.

Jan 1, 1974

By Walter W. Kaufman

This report summarizes a study conducted to establish the nature and impact of regulations governing disposal of refuse from underground coal mines. The regulations affecting refuse disposal in eight major coal producing states are collected, summarized and reviewed. Federal regulations applicable to refuse generated by underground coal mines are also included. Common refuse disposal practices are discussed as are the refuse quantities generated annually in each study state. Technical requirements of regulations are discussed acid presented in appended tables. Economic implications are also assessed through cost analyses of three major types of disposal processes. The report also includes an assessment of future trends in regulation and refuse generation plus a series of recommendations concerning potential improvements in both the regulatory and refuse disposal processes.

Jan 1, 1978

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the fuel-briquet and packaged-fuel producers in the United States and publishes economic data on these industries, based upon reports submitted voluntarily by producers. This publication lists all producers that reported commercial production to the Bureau for 1960 and presents data on individual plants. The companies named herein represent virtually all producers of processed minerals fuels. A few small plants may not have been canvassed or failed to respond to the survey because some of the smaller plants operate intermittently and the survey is voluntary. All plants that reported commercial production were included; regardless of size. Specifically excluded were plants that manufactured briquets from wood charcoal. Fuel briquets and packaged fuel are manufactured solid fuels, produced by mixing fine-sized mineral fuels with binding materials and compressing into small individual shapes, Briquets are produced in pillow-shaped and cylindrical form, are 2 to 4 inches long, and weigh 2 to 4 ounces. Packaged fuel consists of 3- or 4-inch cubes; 6 or 8 of which are wrapped together in heavy kraft paper to form a package weighing 10 to 15 pounds, Briquets are durable and may be stored and handled as bulk fuel; packaged fuel breaks easily and must be stored indoors to prevent it from deteriorating. Whereas briquets are consumed in many areas as a general residential fuel, packaged fuel is more of a specialty item, used at times to supplement other fuels. Packaged fuel is burned without re-moving the paper and is referred to as the "white glove" fuel.

Jan 1, 1961

By Charles E. Whieldon

The importance of producing more oil from known petroleum reserves has placed increased emphasis on the application of secondary-recovery methods. Recently published reports3 4/ describe the results of waterflooding in Roane and Pleasants Counties, W. Va. (see fig. 1.) This report describes the Barron Kidd Oil Co.?s Santee waterflood project, Maxton sand, Burton field, Church district, Wetzel County, W. Va. (See fig. 2.) The Federal Bureau of Mines hopes that these reports will stimulate interest in improved waterflooding techniques, thereby discouraging premature abandonment of oil leases.

Jan 1, 1961

By O. Q. Leone

A processing unit was developed for the complete cleaning of titanium alloy chips. The process uses solvent degreasing, magnetic separation, and anodic solution of nonmagnetic impurities in 10 weight-percent sulfuric acid. Vacuum arc-melted ingots weighing approximately 10 pounds each were prepared from cleaning chips according to ingot specifications.

Jan 1, 1973

By Thomas Curtin

The Bureau of Mines, in its researches aimed to prevent wastes and to increase efficiency in oil-well practice, has investigated the matter of casing troubles and fishing methods. The results of the investigation are set forth in this paper. After expensive development work, many wells being drilled for oil have been abandoned because of casing troubles. These troubles in many instances have been thought to be insurmountable, whereas they are sometimes susceptible of solution. In fields_ where casing difficulties are of daily occurrence, methods have been evolved for combating them. Were these methods more widely known and applied wherever the same conditions exist, the oil industry at large would be greatly benefited. This report attempts to classify these troubles and suggests solutions that will save the operator discouragement and expense. It is assumed throughout this paper that the reader is so familiar with the ordinary oil-well drilling and fishing methods that detailed explanation is unnecessary. The well-drilling terms that are used herein will be readily understood by those for whom this discussion is intended. However, in order to avoid confusion as to the sense in which some of these terms are applied, definitions &re included.

Jan 1, 1920

By Bradley V. Johnson

This publication summarizes the in-house and contract research and development projects conducted since 1974 by the Bureau of Mines for the control of noise and vibrations from surface mine blasting.

Jan 1, 1982

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Common-wealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. Except for the mineral fuel commodities, the detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. In October 1977, responsibility for the collection of data on mineral fuels-coal, petroleum, natural gas, and natural gas liquids-was transferred to the newly created Department of Energy. Although chapters covering these commodities will no longer appear in Volume I of the Minerals Yearbook, quantity and value data have been included in most of these summary tables to maintain statistical consistency in State and national value of overall crude mineral output. This shift in responsibility has also resulted in changes to the composition of the "Nonmetals" and "Mineral Fuels" groups in table 1 and table 2. The commodities-asphalt and related bitumens (natural), carbon dioxide (natural), helium, and peat-have been removed from the "Mineral Fuels" group, and are now included under the "Nonmetals" group. There has been no change in the components of the "Metals" group.

Jan 1, 1980

By F. A. Penning

Improved skips, with lightweight cylindrical bodies, have made a significant contribution to advancing mine hoisting technology. New concept skips of aluminum bodies with rubber lining; fiberglas bodies with polyurethane liners have been designed and fabricated for field testing at an operating mine. New design, adjustable guide rollers have shown improved ride characteristics with noticeably less wear. Major reductions have been made in stress levels and stress concentrations. Field experience has shown the practicality of the approach. Guide alignment has been measured using the Guide Alignment Measuring System (GAMS). Analysis has been applied to interpret the data. Field measurements in an operating shaft and a test tower have shown the agreement in data from GAMS and plumb wires. Reproducibility has been demonstrated. The data are useful to realign shafts, to use as s maintenance tool, and to evaluate the maximum safe hoisting speeds. The surveys are made at several hundred feet per minute and the system is self-contained. Dynamics of skip-guide interaction has been analyzed using the computer program SKIP II. The effects of speed, weight, type of guides, kind of misalignment have been studied. Resonance has been demonstrated and factors that eliminate resonance have been identified. Data from the GAMS surveys are applicable to the SKIP II program. Interaction between the hoist rope and the mine conveyance has also been studied. Computer programs and closed-form solutions are presented. Economic impact of lightweight skips is presented for an existing mine and for a new mine. Reduction in rope size has a profound effect when using a lightweight skip for the same capacity. Increased productivity can be realized by keeping maximum rope pull the same while increasing skip capacity. Examples and charts project the significant savings in capital expenditure for new installations.

Jan 1, 1985

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and the results are described in this report.

Jan 1, 1983

By John H. Soulé

This paper describes the location and general features of the ?Red Bed? or sandstone copper deposits in southeastern Colorado and New Mexico. Most of the areas containing this type of deposit were visited, and many deposits were examined. Some deposits were not visited because of lack of information as to their location. In the large area covered a great variety of climatic, geographic, and topographic conditions exists. Some of the deposits are in arid areas, whereas others are in heavily forested regions. Altitudes range from 3,400 to 9,200 feet, and the terrain varies from flat plains to rugged mountains. Transportation is a difficult problem in most of the districts, involving long truck hauls to a railroad and long rail hauls to a smelter.

Jan 1, 1956

The small-scale surface mining operation in northern regions is typically located in a remote, ungaged basin. With the recent increase in the economic potential of mining, the number of small operations is increasing. The year-to-year variability in precipitation in this region under study is of great concern to mine operators. Some years may yield only 5 to 6 inches of precipitation, while others may yield in excess of 15 inches. Such variability makes placer mining operations difficult to plan, since low water years may result in too little run-off for gravel washing and high water years may result in flooding of mining developments. There are no official streamfloaw records in many watersheds in the northern region containing placer mining claims. However, information from other streams permits calculation of an estimated discharge for a watershed under consideration using average flows per square mile of drainage. It is to be emphasized that these are average or expected figures in reality, one water year may be significantly wetter or drier than another. This high variability of annual precipitation is significant in relation to placer operations because of the large quantities of water required for this type of mining. Some operations can not operate in low water years. In the larger watersheds, operations may continue in low water years but at a slower pace because of longer water collecting times. The high variability of available run-off rakes placer mining in many parts of Alaska difficult to plan on a long range because of the unpredictability of water supplies.

Jan 1, 1985

By F. A. Jones

Increased mechanization .of coal mines has emphasized the need for study of actual power requirements of the various machines employed in the production of coal and losses in the distribution of power to these machines. These studies are being made in order that hazards, excessive use of power, and high maintenance cost of equipment resulting from these losses may be analyzed and eliminated where possible. Research on the use of electric power in-coal mines was suggested by the Advisory Committee of the Bureau of Mines in 1937, and it was decided to begin with a study of individual machines of various types under operating conditions in modern coal mines. The transmission of power, particularly line losses and inadequate return circuits, should be a part of the investigation. This report presents some of the data of an initial study in commercial mines. ACKNOWLEDGMENTS The superintendents, engineers, and other officials of the two mines studied cooperated fully and aided in setting up and transporting the test equipment, giving such information as was requested.

Jan 1, 1942

By H. P. Greenwald, Irving Hartman, H. C. Howarth

"INTRODUCTION A report of tests of seven small pillars formed from the Pittsburgh coal bed in the Experimental coal mine was given in Technical Paper 605 5/ Five additional pillars were tested between July 1939 and. October 1940. The data obtained, in the later tests permit an extension of the conclusions reached in Technical Paper 605, which appears to be important enough to the mining industry to justify a progress report that will explain briefly what it is and how it was obtained. Full detail of the tests will appear in a second technical paper, preparation of which is deferred so that results of pillar tests now under way my be included.DESCRIPTION OF TESTSExcept for minor improvements in operating details, the five additional tests were made as described in Technical Paper 605, pages 2 to 7. Briefly, the desired pillar was formed from the coal bed, by excavating a passage around it (no explosives were used), and enough material was removed from above to permit installation of the assembly used for applying pressure. Each pillar was tested resting on its original fireclay floor, which was restrained from lateral flow by a ring of concrete. Vertical and lateral movement of the pillars in two directions as measured carefully in all tests."

Jun 1, 1941

By R. H. Sprute

This report describes Bureau of Mines laboratory test results in electrokinetic dewatering and consolidation of metal-mine tailings. Tailings were placed in 0.3-cubic-foot Plexiglass models, and dc potential was applied until dewatering ceased. Time-oriented measurements of water removal, changes in resistivity, and power consumption were recorded during the dewatering process. Dewatered material was tested for moisture content and density. Equipment and procedures were developed to optimize the method for unclassified mill tailings from a particular mine in the Coeur d'Alene, Idaho, district. Results indicate the method to be highly effective in dewatering and consolidating this material.

Jan 1, 1974

By Chas. G. Maier

The absence of plants on the Pacific coast for the reduction of iron ores usually is attributed to the fuel situation there. Thus, the bulletin of the. State Division of Mines for 1933, entitled "California Mineral Production," says: "There are considerable deposits of iron ore known in California, notably in Shasta, Mad era, Placer, Riverside, San Bernardino, and Los Angeles Counties, but production has so far been limited for lack of an economic supply of coking coal." It has been estimated that the six major steel plants of the Pacific coast have an annual ingot capacity of 600,000 tons. The present need for tin plate averages 300,000 tons yearly for California alone, of which some 12 percent is manufactured locally. If the consump¬tion of other iron and steel products in 1929 may be taken as an approximate, estimate of the normal requirement for such products, it may be estimated further that, 65,000 to 75,000 tons each of cast-iron pipe and steel reinforcing bars and 300,000 to 400,000 tons of structural shapes and plates will be required annually in California.

Jan 1, 1936

By J. R. Cobble

As part of the Federal Bureau of Mines project to develop new or improved materials for metallurgical furnace applications, the Tuscaloosa (Ala.) Research Center has conducted research to develop a reproducible laboratory test for evaluating the resistance of refractories to molten slags. Tests were conducted with a slag representative of slag used to produce mineral wool. A rotating cylindrical furnace was lined with the brick being tested, and it was operated at temperatures up to 1,660° C for periods ranging from 8 to 32 hours. The effects of such variables as slag temperature, rotational velocity, charge rate, and contact time on refractory erosion were determined. The research demonstrated the reproducibility of the test procedure developed.

Jan 1, 1980

By F. A. Jones

Increased mechanization .of coal mines has emphasized the need for study of actual power requirements of the various machines employed in the production of coal and losses in the distribution of power to these machines. These studies are being made in order that hazards, excessive use of power, and high maintenance cost of equipment resulting from these losses may be analyzed and eliminated where possible. Research on the use of electric power in-coal mines was suggested by the Advisory Committee of the Bureau of Mines in 1937, and it was decided to begin with a study of individual machines of various types under operating conditions in modern coal mines. The transmission of power, particularly line losses and inadequate return circuits, should be a part of the investigation. This report presents some of the data of an initial study in commercial mines. ACKNOWLEDGMENTS The superintendents, engineers, and other officials of the two mines studied cooperated fully and aided in setting up and transporting the test equipment, giving such information as was requested.

Jan 1, 1942

By Wallace W. Roepke

The Bureau of Mines conducted a series of experiments using Illinois No. 6 coal to determine the effect of asymmetric wear on airborne respirable dust (ARD), specific energy, cutting force, and normal force. Plumb-bob-type bits--one new bit and four ground with different sized flats--were used. Constant-depth linear cuts at 0.32, 0.64, 1.27, and 2.54-cm cut depths were made. Both cutting force and normal force increased as the flat area increased. Specific energy demonstrated a statistically significant increase with flat area at the 0.32-and 1.27-cm cut depth only. Specific ARD showed a statistically significant decrease with increasing flat area only at the 0.64-cm cut depth. Increasing cut depth increased cutting force but decreased specific energy and specific ARD. Normal force increased with increasing cut depth for the new bit but exhibited a maximum at 0.64 cm for the bits with flats.

Jan 1, 1983

By Dick T. Atkinson

This report describes the Foster-Miller program that designed, developed, built and tested an automatic, remote control mine car coupler. This new coupler gives the motorman the capability to selectively couple and uncouple cars from the locomotive, to transmit braking intelligence to the coupled car s and to determine if the trip is intact. Hazards due to derailment and runaway cars will be reduced as the brakes are automatically applied in any uncoupled car. Laboratory tests described herein have been completed on the coupler set. Applications include, but are not limited to, the unit train system.

Jan 1, 1976