Search Documents

By J. R. Cobble

As part of the Federal Bureau of Mines project to develop new or improved materials for metallurgical furnace applications, the Tuscaloosa (Ala.) Research Center has conducted research to develop a reproducible laboratory test for evaluating the resistance of refractories to molten slags. Tests were conducted with a slag representative of slag used to produce mineral wool. A rotating cylindrical furnace was lined with the brick being tested, and it was operated at temperatures up to 1,660° C for periods ranging from 8 to 32 hours. The effects of such variables as slag temperature, rotational velocity, charge rate, and contact time on refractory erosion were determined. The research demonstrated the reproducibility of the test procedure developed.

Jan 1, 1980

By Wallace W. Roepke

The Bureau of Mines conducted a series of experiments using Illinois No. 6 coal to determine the effect of asymmetric wear on airborne respirable dust (ARD), specific energy, cutting force, and normal force. Plumb-bob-type bits--one new bit and four ground with different sized flats--were used. Constant-depth linear cuts at 0.32, 0.64, 1.27, and 2.54-cm cut depths were made. Both cutting force and normal force increased as the flat area increased. Specific energy demonstrated a statistically significant increase with flat area at the 0.32-and 1.27-cm cut depth only. Specific ARD showed a statistically significant decrease with increasing flat area only at the 0.64-cm cut depth. Increasing cut depth increased cutting force but decreased specific energy and specific ARD. Normal force increased with increasing cut depth for the new bit but exhibited a maximum at 0.64 cm for the bits with flats.

Jan 1, 1983

By Ralph P. Carter

It is apparent that coal will play an increasingly important role in satisfying the nation's energy requirements for the remainder of this century. Both deep mining and surface mining will be practiced to develop known U.S. coal reserves, but until significant improvements in the productivity of deep mining emerge, surface mining is likely to be predominant. This report addresses the problems of coal extraction and surface mine reclamation in the 11-state Midwestern coal resource region, where surface stripping of high-sulfur, bituminous coal has been a well-developed industry for most of this century. Midwestern coal markets have declined in recent years. In part this is a result of widespread conversions to more convenient and (apparently) economical liquid and gaseous fuels, but the decline in Midwestern coal use is also attributable to the impact of current air pollution control regulations that prohibit emissions of sulfur oxides and particulate matter. A part of the regional demand for Midwestern coal has been transferred to the Northern Great Plains where extensive low-sulfur coal reserves are currently being developed.

Jan 1, 1974

By R. H. Sprute

This report describes Bureau of Mines laboratory test results in electrokinetic dewatering and consolidation of metal-mine tailings. Tailings were placed in 0.3-cubic-foot Plexiglass models, and dc potential was applied until dewatering ceased. Time-oriented measurements of water removal, changes in resistivity, and power consumption were recorded during the dewatering process. Dewatered material was tested for moisture content and density. Equipment and procedures were developed to optimize the method for unclassified mill tailings from a particular mine in the Coeur d'Alene, Idaho, district. Results indicate the method to be highly effective in dewatering and consolidating this material.

Jan 1, 1974

By Dick T. Atkinson

This report describes the Foster-Miller program that designed, developed, built and tested an automatic, remote control mine car coupler. This new coupler gives the motorman the capability to selectively couple and uncouple cars from the locomotive, to transmit braking intelligence to the coupled car s and to determine if the trip is intact. Hazards due to derailment and runaway cars will be reduced as the brakes are automatically applied in any uncoupled car. Laboratory tests described herein have been completed on the coupler set. Applications include, but are not limited to, the unit train system.

Jan 1, 1976

By F. A. Jones

Increased mechanization .of coal mines has emphasized the need for study of actual power requirements of the various machines employed in the production of coal and losses in the distribution of power to these machines. These studies are being made in order that hazards, excessive use of power, and high maintenance cost of equipment resulting from these losses may be analyzed and eliminated where possible. Research on the use of electric power in-coal mines was suggested by the Advisory Committee of the Bureau of Mines in 1937, and it was decided to begin with a study of individual machines of various types under operating conditions in modern coal mines. The transmission of power, particularly line losses and inadequate return circuits, should be a part of the investigation. This report presents some of the data of an initial study in commercial mines. ACKNOWLEDGMENTS The superintendents, engineers, and other officials of the two mines studied cooperated fully and aided in setting up and transporting the test equipment, giving such information as was requested.

Jan 1, 1942

By S. H. Lorain

Mechanized dirt-moving equipment has greatly increased the scope of prospect trenching by lowering the costs and increasing the speed of such work. Where the soil covering was more than 3 or 4 feet deep, operators were quickly discouraged and abandoned surface exploration in favor of shaft sinking, drifting, or diamond drilling; wildcat trenching was seldom undertaken, even where the soil covering was thin. Although power shovels, trench diggers, and draglines are useful under special conditions, caterpillar-mounted angledozers will usually do the same type of work and have a far wider range of adaptability. They are therefore incomparably the most generally useful equipment for the purpose. Since 199 the Bureau of Mines has been engaged in a widespread search for minerals useful to the war program; this work required a great deal of pioneer exploration in areas where known outcrops were marginal or subcommercial by pre-war standards. Engineers in charge of field operations were quick to perceive the applicability of mechanized trenching on a fairly large scale, particularly in the Northwestern States, where completely exposed vein-outcrops are rare. Probably no other organization to date has done a comparable amount of angledozer prospect trenching under such a wide range of conditions. The following comments and accompanying cost tables are based on work performed chiefly in Idaho, under a variety of physical and climatic conditions. The most important applications of the angledozer for such work may be described under three heads:

Jan 1, 1944

By H. P. Greenwald, Irving Hartman, H. C. Howarth

"INTRODUCTION A report of tests of seven small pillars formed from the Pittsburgh coal bed in the Experimental coal mine was given in Technical Paper 605 5/ Five additional pillars were tested between July 1939 and. October 1940. The data obtained, in the later tests permit an extension of the conclusions reached in Technical Paper 605, which appears to be important enough to the mining industry to justify a progress report that will explain briefly what it is and how it was obtained. Full detail of the tests will appear in a second technical paper, preparation of which is deferred so that results of pillar tests now under way my be included.DESCRIPTION OF TESTSExcept for minor improvements in operating details, the five additional tests were made as described in Technical Paper 605, pages 2 to 7. Briefly, the desired pillar was formed from the coal bed, by excavating a passage around it (no explosives were used), and enough material was removed from above to permit installation of the assembly used for applying pressure. Each pillar was tested resting on its original fireclay floor, which was restrained from lateral flow by a ring of concrete. Vertical and lateral movement of the pillars in two directions as measured carefully in all tests."

Jun 1, 1941

By Thomas V. Falkie

The purpose of this work was to investigate the rate at which coal is delivered from the underground working face by gathering arm type loaders as employed on continuous mining machines, to identify the factors -- geometrical, geological, mechanical, or procedural which affect the delivery rate, and to develop quantitative rate descriptive equations for the loading function. The mathematical techniques employed were factor analysis and multiple linear regression. It was determined that the coal-cutting function of the continuous mining machine is the factor that primarily influences the loading function. The geometrical factors -- the dimensions of the work area in relation to the dimensions of the mining machine - were the factors of secondary influence. Fifty-five percent of the experimental variation in the loading function was explained in terms of the six most prominent independent variables. It is expected that this work will be useful in operations-research studies as applied to underground coal mining, and with refinement will enable mine planners to select equipment based on the operating characteristics of the equipment and the mining conditions.

Jan 1, 1972

Introduction MINING IS THE BRANCH OF INDUSTRY involving the exploration and removal of minerals from the earth (figure 1). Mining is one of the oldest and most important endeavors of humankind, because it provides the raw ingredients for most of the material world around us and, like agriculture, is the lifeblood of civilization. The main objective of any type of mining is to remove the valuable material economically and safely with minimum damage to the surrounding environment. The Earth has many natural resources on which we depend that must be mined. Coal, oil, gas, and other mineral fuels are used for heating electricity, and numerous industrial processes. Nonfuel minerals such as iron ore, precious metals, and industrial metals, and nonmetallic materials like sodium and potassium are used in chemical and agricultural applications. Even crushed stone used in road building and other construction projects must be mined. Mining affects our standard of living and impacts almost everything we do. A myriad of items that we use in our homes and offices and for transportation, communications, and national defense all require minerals (figure 2). For example, more than 30 different minerals are needed to make a television or telephone! Table 1 lists several commonly mined materials and some of the end uses in our daily lives.

Jan 1, 1995

By M. E. Poad

Structural properties of steel-fiber-reinforced shotcrete and polymer-impregnated shotcrete, both plain and fiber-reinforced, were investigated by the Federal Bureau of Mines, Spokane Mining Research Center. The research center has found that flexural strengths can be increased by as much as 106 percent, and splitting-tensile strength by 50 percent, by introducing randomly oriented steel fibers. A slight decrease of compressive strength was found in the fiber-reinforced shotcrete. Polymer-impregnated shotcrete exhibited a threefold to fourfold increase in compressive and splitting-tensile strength. The techniques of preparing shotcrete with the dry process, using both fast-set agents and regulated-set cement, are described, along with the results of physical-property testing. Physical properties include compressive and splitting-tensile strengths, tangent and secant moduli, and stress-strain curves for plain shotcrete, fiber-reinforced shotcrete, and polymer-impregnated plain and fiber-reinforced shotcrete. Flexural strengths for plain and fiber-reinforced shotcrete are also reported. Steel-fiber shotcrete is the more promising of the new structural materials for ground support, and additional research is recommended.

Jan 1, 1975

By Paul G. Swanson

This investigation was conducted to identify the principle causes of spoil instability problems in the Eastern Coal Province. The study was also conducted to develop a matrix to predict the strength and groundwater parameters necessary to conduct stability analyses on a proposed reclamation scheme. Suggestive methods to reduce spoil instability potential are also included. Numerous physical property, strength, compressibility, chemical and mineralogical tests were conducted on mine spoil samples obtained from 11 different surface mine sites. Site characteristics that influence the position of the post reclamation groundwater table were identified. Distinct regions within the Eastern Coal Province with high incidences of surface mine slides or high landslide susceptibility were identified. The application of the predictive matrices developed in this study is for surface mine sites mined and reclaimed in general accordance with the Surface Mine Reclamation Control Act of 1977. A review of current mining practices and the relative effect on spoil stability is included.

Jan 1, 1983

By Stephen Gerard Sawyer

This report presents a Fortran IV computer program for the structural analysis of space-frame protective canopies used in underground mines to protect equipment operators from falls of roof, face, or rib. This program entitled CANOPY permits rapid calculation of the elastic strength of a canopy for a variety of static loading conditions. Stresses in, and displacements of each structural member are computed and printed out. Additionally, identification of all members that have commenced yielding, weight of the canopy, total loads on the canopy, and maximum loads that the canopy can sustain elastically are output. Program description, input instructions, program listing, and two example problems are included.

Jan 1, 1972

By Joseph L. Buckley

A total of 55 conveyor belt fire tests were conducted in the Bureau of Mines Fire Test Gallery, located at the Factory Mutual (FM) Fire Test Center West Glocester, R.I. The objectives of these tests were to: 1) determine the fire resistance and burning characteristics of various conveyor belt materials under simulated mine conditions; 2) provide essential data for designing a reliable bench-scale conveyor belt fire resistance test; and, 3) determine fire test conditions that will discriminate between low, moderate and high fire resistant materials. Belts, representative of those which mold he found in underground coal mines were examined under n umber of experimental conditions which included; ignition intensity; air flow rate; ratio of belt bright (h2) to overall gallery height (h1); exposure time; and, belt width. It was found that fire propagation could be achieved for some "fire resistant" belts (complying with the present Schedule 2G standard for approval) when exposed to an Ignition source of =6000 Btu/min for a 15-min period at a belt height ratio of 01.66. There appears to be a dependency of flame propagation on air flow rates and belt width, although the tests performed do not provide a quantitative trend. Recommendations are made for additional work to resolve some anomalous date and to fill voids in the rest program.

Jan 1, 1978

By James H. Snyder

This final report presents results of a program to develop a new conveyor system, adaptable to existing miners or loaders, which reduces the noise level to 90 dBA without reducing machine performance. The trial conveyor design consists of a main conveyor and a swinging tail conveyor. The main conveyor incorporates a rubber-covered return guide roller, rubber mounting of pillow blocks, rubber cover of the return bed, and a rubber belt running between the flight chain and the conveyor bed plate. Testing took place in a surface coal pit and underground at the Peabody Spur Mines in Boonville, Indiana. Noise Levels as low as 90 dSA were observed on the surface and 93/94 dRA underground. Recommendations for further work are also presented.

Jan 1, 1976

By Ronald F. Balazik

[This Bureau of Mines study is intended to identify and evaluate potential effects of impending large-scale U. S. rail line closings (abandonment) on domestic nonfuel mineral industries. This is the first nationwide study of rail abandonment impacts focused on nonfuel minerals. The analyses presented is based principally on a survey of 200 rail freight records and on statistical tests that correlated 2,000 points in the Bureau's Mines Industry Location System (MILS) with 700 prospective abandonments throughout the United States. The conclusions derived from the analysis can be useful in evaluating proposed national rail abandonment policy rind legislation regarding nonfuel miner it shipping. Among these conclusions are the following: (1) Certain mineral materials (especially fertilizers) are likely to account for a large percentage of the rail traffic affected by abandonment in the next few years, but the total tonnage- involved will be small; (2) abandonment will adversely affect some mineral shippers, particularly local smart haulers; and (3 abandonment could significance reduce the opportunity to develop new resources or reopen defunct mining facilities. Despite these problems, however, the data examined in this study do not indicate that current abandonment trends will cause widespread disruption 01 domestic nonfuel mineral shipping.]

Jan 1, 1980

By Harvey L. Pastan

The purpose of the investigation and analysis described in this report is to assess the data flow requirements that are required for remote supervisory control of a continuous mining system. Since these control concepts as applied to continuous underground mining are still in a formative stage at the present time during the first half of 1975, assumptions had to be made based upon engineering judgment as to what embodiment of mining machinery and control methodology seemed most feasible for achieving such a system. Based upon these assumptions and estimates of the control system's accuracy and response requirements, it was then possible to estimate the communication requirements for the assumed system configuration. 2. Approach The team members responsible for this study visited numerous coal mines to observe room and pillar mining operations in both high and low coal. The objective was to observe the methods of operating a variety of continuous mining machinery and haulage equipment with a view toward defining the problems to be overcome in the application of automation to the coal extraction process. Descriptive information concerning the mining equipment was obtained through contacts with the manufacturers. Conferences with Bureau of Mines personnel, equipment manufacturers and developers, and mine operators were held to explore the current thinking and developments being pursued toward automation and increasing both production and productivity.

Jan 1, 1975

By Mark P. Meyer

A mineral investigation of the Chugach National Forest, Alaska was conducted jointly by the U.S. Geological Survey and the U.S. Bureau of Mines from 1979 to 1983 as part of the RARE II program. The U. S. Geological Survey remapped the geology and distribution of mineral resources. The Bureau investigated mines, prospects, and mineral occurrences. Previously unreported mineralization in three areas, Long Bay, Wells Bay, and Miners River were discovered in the western portion of the SOUND study area. Copper, lead, zinc, gold, silver, nickel, cobalt, fluorite, and arsenic were found in north-northeast to north-northwest trending shear zones, veins, felsic dikes, and granitic intrusives in Tertiary Orca Group metasedimentary rocks.

Jan 1, 2011

By A. N. Baldwin

This report documents the work performed under Bureau of Mines Contract J0265029 to study and develop two innovative mining systems: ? An underground auger capable of augering into the right and left ribs without repositioning the machine ? A conventional mining system employing recently developed innovative machinery. The report is separated into two volumes to document the two studies separately. Volume I describes work performed and the recommended concept for a bidirectional auger. Volume II describes the studies of mining equipment performance and mining plans developed to determine a conventional mining plan offering improved productivity.

Jan 1, 1977

By J. W. Howland

A demonstration of dozer blades, designed for recontouring area-mined spoil and shown effective at Kansas and East Texas surface mine sites, was conducted at a Northeast Arizona surface coal mine to determine their effectiveness in different climate and soil conditions. The specialized tools were: 48-ft angle blade (on side-by-side tractor), 24-ft grading bar, modified 24-ft "U" blade (on side-by-side tractor), and a 13-ft deep "U" blade. Interest in the increased dirt-handling capacity of a previously built 22-ft blade, resulted in the design of a new Centerflow Blade of good versatility, able to maintain increased flow in otherwise difficult-to-move spoil. The demonstration involved 263 acres and showed a reduction of 50% in reclamation costs and 20% in fuel requirements for this mine site over conventional equipment. This savings resulted from improved technology, trained operators, and rigorous application of supervisory and monitoring techniques. Procedures and results of the demonstration are presented and analyzed here, along with guidelines for application of findings.

Jan 1, 1982