Search Documents

By R. T. Sorensen

Research and testing in a small scale equivalent of a commercial flota-tion plant was completed on four low-grade, iron-bearing materials from the western Mesabi range. Closed circuit-flotation of calcium-activated silica with fatty acid collector developed data for comparison with the batch process and highlighted problems not evident from previous bench testing. The four ore samples contained from 27 to 39 percent Fe and were equally represented by nonmagnetic taconite and semitaconite type materials. Iron concentrates containing 6.0 percent, or less, SiO2 were made 5, all four samples. Of the two material types, the semitaconite was the ore amenable to treatment, yielding iron recoveries of about 90 percent as cc pared with 70 to 80 percent for the other. Pilot plant tests showed that concentrate grade made in batch tests could be duplicated in the closed circuit and demonstrated that the amount of recoverable middling iron varied considerably between ore samples. The continuous tests also showed that water temperature strongly influenced results in the treatment of one ore but apparently was of indifferent consequence in another. Progress in thickening and filtration of flotation concentrates was made through introduction of tapioca flour to serve the dual role of iron mineral depressant and flocculant.

Jan 1, 1966

By Jürgen F. Brune, R. Karl Zipf, Michael J. Sapko

Seals are barriers constructed in underground coal mines throughout the United States to isolate abandoned mining panels or groups of panels from the active workings. Historically, mining regulations required seals to withstand a 140-kPa (20-psig) explosion pressure. However, the Mine Improvement and New Emergency Response Act (“MINER Act”) requires the Mine Safety and Health Administration (MSHA) to increase this design standard by the end of 2007. This report provides a sound scientific and engineering justification to recommend a three-tiered explosion pressure design criterion for new seals in coal mines in response to the MINER Act. Much of the information contained in this report also applies to existing seals. Engineers from the National Institute for Occupational Safety and Health (NIOSH) examined seal design criteria and practices used in the United States, Europe, and Australia and then classified seals into their various applications. Next, the engineers considered various kinds of explosive atmospheres that can accumulate within sealed areas and used thermodynamic calculations and simple gas explosion models to estimate worst-case explosion pressures that could impact seals. Three design pressure-time curves were developed for the dynamic structural analysis of new seals under the conditions in which those seals may be used: unmonitored seals where there is a possibility of methane-air detonation or high-pressure nonreactive shock waves and their reflections behind the seal; unmonitored seals with little likelihood of detonation or high-pressure nonreactive shock waves and their reflections; and monitored seals where the amount of potentially explosive methane-air is strictly limited and controlled. Figure 1 is a simple flowchart that illustrates the key decisions in choosing between the monitored or unmonitored seal design approaches and the three design pressure-time curves. For the first condition, an unmonitored seal with an explosion run-up length of more than 50 m (165 ft), the possibility of detonation or high-pressure nonreactive shock waves and their reflections exists. The recommended design pressure-time curve rises to 4.4 MPa (640 psig) and then falls to the 800-kPa (120-psig) constant volume (CV) explosion overpressure. For unmonitored seals with an explosion run-up length of less than 50 m (165 ft), the possibility of detonation or high-pressure nonreactive shock waves and their reflections is less likely. A less severe design pressure-time curve that simply rises to the 800-kPa (120-psig) CV explosion overpressure may be employed. For monitored seals, engineers can use a 345-kPa (50-psig) design pressure-time curve if monitoring can ensure that (1) the maximum length of explosive mix behind a seal does not exceed 5 m (16 ft) and (2) the volume of explosive mix does not exceed 40% of the total sealed volume. Use of this 345-kPa (50-psig) design pressure-time curve requires monitoring and active management of the sealed area atmosphere. These design pressure-time curves apply to new seal design and construction.

Jan 7, 2007

By A. Wahab Khair, W. M. Devilder

"This paper presents an analysis of fragment size distribution and characteristics of fracture surface in coal cutting using a rotary coal cutting simulator. Coal cutting by a drum type continuous miner was simulated in the laboratory. A series of tests along both the face and butt cleat direction of coal under different operating and in-situ conditions were performed. In each experiment the cut surface was photographed microscopically and the coal cuttings were collected and sized. Data were used to show how and to what extent various parameters effect size distribution of the coal cutting and how this correlates with the characteristics of the fracture surface. This study resulted in establishing a number of distinct correlations between the size distribution and fracture surface. These correlations were primarily based on the degree of interaction between adjacent bits and the amount of bit-coal interaction taking place on the cutting path. Some of the major results of this study are as follows:Zones of bit-coal interactions proved vital toward understanding the effect the conical bit has on the fragmentation process. This in turn led to the identification of areas which are responsible for the production of fines and generation of respirable dust.The various parameters employed in the coal cutting experiments which showed a strong effect on the coal fragment size distribution were: bit type, bit spacing, depth of cut, in-situ stresses, and cleat orientation. Bit angle and cutting head velocity exhibited the least effect and no correlation was established.From this study it is obvious that the key to achieving efficient coal fragmentation is to limit the degree of bit-coal interaction that takes place throughout the bit path while causing maximum interaction between adjacent bits. Accomplishing this not only increases the percentage of large fragments produced but limits the amount of secondary crushing that takes place in the bit path thus resulting in decreasing fines and consequently, the amount of respirable dust generated.Over 2,000 continuous mining machines (introduced in the 1950's) equipped with conical bits or point attach bits account for well over half of the United States' production from underground coal mines. Today, competition in the coal industry has increased, due mainly to coal market conditions and legal restrictions, thus placing an emphasis upon increasing production, efficiency and health/safety of the workers. Mine operators are always interested in finding the most efficient performance of continuous mining machinery to produce the largest amount of size of coal at the lowest cost. An increase of fine material sent to the cleaning plant can seriously overload the plant to the extent that plant efficiencies deteriorate significantly (1). Also, the difficulty and expense of cleaning very small particles often cannot be done economically and thus, thousands of tons of coal are sent to the refuse pile because of costly or ineffective cleaning facilities. It has been said, ""the efficient extraction of coal or rock implies breakage into a size range that contains a minimum quantity of very small sizes"" (2). All known fragmentation theories concur that more fragmentation requires more energy (3). So, the importance of reducing fines is already evident from an outlook upon efficiency.Now, let's consider another view point., duet generation."

Jun 1, 1988

By Martin J. Gavin

"Before discussing oil shales it may be well to consider briefly the conditions surrounding the petroleum industry in the United States, because these largely explain why so much interest is being manifested in oil shales. The United States is not only the greatest producer of petroleum in the world, its output amounting to about 65 per cent of the world's total production; but is also the world's greatest consumer, using more petroleum than it produces within its own borders. For the past four or five years it has been necessary to import oil at a continually increasing rate to make up the deficit between domestic production and domestic consumption. Experts who have made a close study of the future supply and demand for, crude petroleum are satisfied that under present production practice and with the development of possible undeveloped productive areas, the gap between domestic consumption and production will steadily .increase.As possible solutions for the impending domestic shortage of oil, various expedients are receiving attention. These may be grouped under three heads, as follows:(1) Temporary measures, such as curtailment of consumption, development of more efficient methods of production, and more efficient utilization of supplies of petroleum still available. It is unlikely that there will be any great curtailment in consumption of petroleum in the United States; rather, consumption will continue to increase unless a real shortage of oil actually forces curtailment of consumption. The other two possibilities mentioned deserve, and are resolving, serious thought. Much experimental work along these lines, some of which has already yielded excellent results, is being done. Obviously, however, any of these remedies are temporary ones only, so far as regards domestic production of petroleum."

Oct 1, 1920

By E. B. Nelson, B. W. Gandrud, B. M. Bird

"The Lewisburg No. 2 mine of the Sloss-Sheffield Steel & Iron Company is located in Jefferson County, Alabama, about 7 miles due north of Birmingham. At this point the coal from the Mary Lee seam when coked in by-product ovens yields an excellent quality of metallurgical coke suitable for use in the iron blast furnace; it is also an excellent steam coal. In mining, all three benches are worked. Coarse impurities are largely gobbed by the miners underground.In addition to giving the data obtained from screen-sizing and float-and-sink tests of a representative sample of the raw coal, this report presents the results of slotted-screen tests to show the proportions of flaky particles in selected sizes, and the results of tests to show how much coal is liberated from impurities by crushing the coarsest sizes. These data have been obtained in connection with an extensive study of coal-washing now being conducted by the U. S. Bureau of Mines and the University of Alabama, with U. cooperation of the different operators of Alabama. As the work progresses other reports will follow containing furtner data on the washability both of the Mary Lee seam and of other seams in Alabama and giving the results obtained in preparing these coals by various methods.Although a great amount of investigative work on the preparation of the Mary Lee scam was previously carried on by the various coal companies of the district, comparatively little of this information has been published. In governmental publications three references have been found. Forbes5 gives a number of sections with proximate and ultimate analyses of face samples taken in the mines. Gandrud and Britton'' show sections of this seam at Flat Creek and New Castle; they also give the specific gravity and ash contents of the partings of coal and impurities. In their paper Yancey and Fraser7 include washability studies and washing data from the Sayreton mine of the Republic Iron & Steel Co."

Jun 1, 1930

By Martin H. Rogoff

The presence of antibiotic materials extractable with polar organic solvents was demonstrated in coals of various ranks. Since these antibiotics occur in low concentrations, 200 pounds of a high-volatile C coal was extracted with acetone at room temperature to obtain sufficient material for detailed study. The biologically active materials in the extract were concentrated by extracting with aqueous sodium hydroxide. The fractions soluble in sodium hydroxide inhibited bacterial cultures when present in concentrations comparable to those at which other antibiotics are active (5 µg/ml). Steam distillation of the extracts did not yield highly active materials, contrary to the finds of other investigators. Mass spectrometry of the extract indicated, mainly, the presence of 6-ring compounds in the region of mass 324 to 392. The predominance of 3-ring aromatic systems found by ultraviolet analysis suggests compounds such as biphenanthryl or similar structures. The activity of the hydroxide- soluble material decreased markedly when the phenolic hydroxyl groups were transformed into trimethylsilyl ethers. Hydrolysis of the ethers yielded a product having the same activity as the original material, which indicates that phenolic compounds are largely responsible for the antibiotic activity observed.

Jan 1, 1963

By R. J. Morrell

The Bureau of Mines conducted a series of laboratory experiments to test a cutting technique for hard rock using large-scale drag cutters. Cutting experiments were performed on rocks ranging in compressive strength from 10,000 to 27,000 Ib/in2, using large drag cutters from 3 to 6 in. in width. The tests were conducted on a special test apparatus, called a ripper tester, which made a curvilinear cut across the rock sample while measuring the cutting force acting on the drag cutter. The cutting method that evolved from these experiments is called ripper cutting, and its energy efficiency appears superior to all other large-scale mechanical fragmentation techniques. In addition, the method cre-ated very little dust, and the wear on the bits was negligible. A fragmentation system based on ripper cutting was then devised, and a large-scale test device was fabricated to allow full-scale laboratory testing of the system. The results of these tests will be published in future Bureau reports.

Jan 1, 1986

The object of this program was to extend the capabilities of visual paging systems both in size and function. The system developed uses the mine pager phone line for communication, monitoring, and remote control. A central station, using a minicomputer, transmits signals by phase inversion modulation of a 16,384 Hz carrier to as many as 999 remote units. The remote unit addressed returns An echo to indicate that it is functioning and, in the case of monitor units, to convey the monitor data. Magnetically latched display dis[c]s, which can be seen from both sides when posted, are used for visual paging. Lists of the addresses of posted pages, unanswered pages, and non-echoing units are prepared by the central station computer. The system was designed to be intrinsically safe and should operate for three months on a 12-volt lantern battery.

Jan 1, 1980

By W. K. Tolley

The Bureau of Mines is testing super critical fluids as solvents to selectively extract valuable components from complex matrices. Materials recovered during supercritical fluid extraction are often highly purified. Using laboratory apparatus designed specifically for supercritical fluid research, Bureau re-searchers have measured the solubility of titanium tetrachloride (TiCI4) in supercritical, liquid, and gaseous carbon dioxide (C02), CO2, a commonly used supercritical fluid, is inert, inexpensive, and nontoxic. Supercritical CO2 formed a single phase with TiCl4 at 45° C and 1,500 psig. When the solution was heated at constant pressure beyond 55° C, TiCl4 precipitated from the fluid. Results showed that TiCl4 solubility in supercritical CO2 is not controlled by the vapor pressure of the solute.

Jan 1, 1989

By M. S. Seehra, R. S. Pandurangi

"INTRODUCTION Silica and kaolin (a layer aluminosilicate) are among the major constituents of most coal mine dusts.' Whereas kaolin is cytotoxic in vitro but nonfibrogenic in vivo in humans and experimental animals,2-4 the cytotoxic and fibrogenic potential of silica is rather well established.5 Wallace and co-workers 6-8 have studied the cytotoxic potentials of both native and surface-modified silica and kaolin and inferred that retoxification is slow in the case of occluded silica vis-à-vis native silica. Recent epide¬miological studies indicate that silica concentration alone in a mine dust, as determined by transmission IR spec¬troscopy (TIRS), does not correlate well with the pro¬gression of coal workers' pneumoconiosis. 9 This obser¬vation has led to the suggestions that silica particles occluded by clays such as kaolin may not be fibrogenic. This proposal requires accurate estimations of kaolin, silica, and occluded silica. The current method of silica analysis in a mine dust sample employs TIRS of the 797- cm -1 band of silica, although its accuracy, as well as that of x-ray diffraction studies, is no better than 25 % , even in a laboratory-generated dust.° In this paper we have employed the techniques of diffuse reflectance spectros¬copy (DRS) and photoacoustic spectroscopy (PAS), in conjunction with an FT-IR spectrometer, for the quan¬titative determination of silica in laboratory-generated silica-kaolin mixtures.One of the main advantages of DRS and PAS is that, in these techniques, problems arising from sample prep¬aration of the KBr-based disks used in TIRS are avoided. There are, however, several other considerations (e.g., particle size effects and saturation phenomenon) which complicate the use of DRS and PAS for quantitative work. 10-25 In this paper, we have carried out a systematic comparison of the quantitative abilities of the two tech¬niques, as applied to the silica-kaolin mixtures, with par¬ticular attention to the saturation behavior of several bands with different absorption coefficients. In particular, we show that a weaker band for silica at 1875 cm-1 is suitable for quantitative purposes, and that quantitative accuracy is higher in DRS than in PAS. Details of this work are given below."

Mar 1, 1992

By Wiliam L. Crentz

The importance of Somerset County, Pa., as a coal producer is due in large measure to the presence reserves of low-volatile bituminous coals. Although many coal beds of minable thickness are present, the important reserves are to be found in those beds underlying the Pittsburgh bed. The Kittenning beds and Freeport beds, which are responsible for the bulk of the present coal production in Somerset County and contain the largest reserves to meet future coal requirements, are usually thin and entirely free from impurities. The Pittsburgh bed, which has been such an important coal deposit in the coal areas immediately west and south of Somerset County, is of secondary importance in this county. Although generally rather friable, Somerset County coals have enjoyed wide receptability as excellent coals and to some extent have been utilized in the metallurgical market.

Jan 1, 1951

By Jack L. Henry

A laboratory and a pilot-plant-scale investigation has been conducted by the Bureau of Mines to examine possible sources of nitride defects in the production of magnesium-reduced titanium sponge. The production of alpha-stabilized nitride inclusions in hot-rolled titanium plate from air contamination of sponge during its manufacture has been experimentally demonstrated. Magnesium-reduced sponge prepared from air-contaminated magnesium or when contaminated by an air leak during reduction, vacuum distillation, or inert gas sweep, shows very large variations in nitrogen content. Refractory nitrides, delta TiN and epsilon Ti2N have been identified in this sponge. The highest incidence of inclusions resulted from sponge that was reduced by air-contaminated magnesium and from sponge subjected to air contamination during the vacuum distillation cycle and during helium sweep. Air contamination of sponge during the reduction cycle was not nearly as effective in producing inclusions. Tests showed that color and texture may not be reliable criteria for locating defects during sponge inspection. Maintenance of good vacuum-tight integrity, filtration of molten magnesium prior to charging into the reduction retort, and mechanical attrition of sponge to pulverize and disperse nitrides are suggested as practices to lower inclusion incidence in commercial titanium ingots.

Jan 1, 1974

By D. R. Tweeton

The U.S. Bureau of Mines, the University of Arizona, Sandia National Laboratories, and Zonge Engineering and Research Organization, Inc., conducted cooperative field tests of six electromagnetic (EM) geophysical methods to compare their effectiveness in locating a brine solution simulating in situ leach solution or a high-conductivity plume of contamination. The brine was approximately 160 m below the surface. The testsite was the University's San Xavier experimental mine near Tucson, AZ. Geo- physical surveys using surface and surface-borehole, time-domain electromagnetic (TEM) induction; surface controlled-source audiofrequency magnetotellurics (CSAMT); surface-borehole, frequency- domain electromagnetic (FEM) induction; crosshole FEM; and surface magnetic field ellipticity were conducted before and during brine injection. The surface TEM data showed a broad decrease in resistivity. CSAMT measurements with the conventional orientation did not detect the brine, but measurements with another orientation indicated some decrease in resistivity. The surface-borehole and crosshole methods located a known fracture and other fracture zones inferred from borehole induction logs. Surface magnetic field ellipticity data showed a broad decrease in resistivity at depth following brine injection.

Jan 1, 2010

By P. H. Floyd

This report presents the results of laboratory beneficiation tests on a sample of scheelite ore and a sample of low-grade scheelite flotation concentrate from the Sangdong mine, Korea. Sangdong was the foremost producer of tungsten concentrates on two occasions - during part of World War II and in 1953. It was also a significant producer of bismuth concentrates. Resources are very extensive and could support a 5,000-ton annual output of tungsten concentrates for many years. Located in the eastern part of South Korea near the 37° latitude, Sangdong has been a vital source of dollar income for the Republic of Korea in recent years. Its shutdown in March 1954 came about as a result of the great decline of tungsten prices and the fact that a sales contract with the United States Government had been terminated, In addition to establishing new markets, the problem of reopening Sangdong will be related to cost reductions and improving mill recoveries. Large quantities of offgrade scheelite concentrates were produced in the past and shipped to the United States for further beneficiation. Other low-grade concentrates and middlings have been stockpiled or discarded at the mine plant.

Jan 1, 1954

By L. G. Trudell, J. W. Smith, K. E. Stanfield

Oil- yield data are presented for 40 sets of core samples and 83 sets of drill cuttings collected in 1952-62 from drilling operations in the Uinta basin of eastern Utah . This accumulated information on the location , extent , and richness of oil shales of the Green River formation is used to appraise the deposits as a source of oil and related products . Core samples used in the study were obtained specifically for evaluating oil shale , and they were satisfactory for this purpose , except they did not completely penetrate the formation . The drill- cutting samples were inferior to the core samples and yielded more erratic results . Consequently, oil yields based on cuttings should be regarded as indicative , rather than definite , until substantiated by other means . In general , the oil- yield data indicate Green River oil shale in Uinta basin is not as thick or as uniform as that in the Piceance Creek basin of western Colorado . However , it is an important potential source of oil . Estimates that beds 15 feet or more thick that average 25 gallons of oil per ton represent at least 120 billion barrels of oil in place are supported by the recent oil- yield data .

Jan 1, 1964

By John H. Soulé

"Bureau of Mines engineers3/ examined the White Eagle fluorspar mine on September 3, 1943, and again on February 17, 1944. The examinations led to a proposal for the exploratory project upon which this report is based. The project, which was supervised by the author and P. L. Russell, was started on April 6, 1945, and completed on June 26, 1945.Geologists4/ of the Federal Geological Survey examined, mapped, and reported on this property prior to initiation of the Bureau of Mines project.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. H. S. Dean, assistant director.Special acknowledgment is due to C. H. Johnson, Rolla, Mo., Division, Mining Branch; to W. R. Storms, mining engineer in charge of the New Mexico field office; and to J. H. Hedges, chief of the Tucson, Ariz., Division Mining Branch. Acknowledgment is owed, also, to Robert Trace and Howard Rothrock, of the Federal Geological Survey, for help in mapping the surface and in logging drill cores.The White Eagle claim is in the east-central part of sec. 34, T. 19 S., R. 9 W., Cooks Peak Mining District, southeastern Grant County, New Mexico. The property is reached from Deming, N. Mex. by taking the paved U. S. Highway No. 260 northwestward for 13 miles to the junction with State Route 61. State Route 61 is a graded but unpaved road and is followed northward for 8 miles to a junction with a poor dirt road, which is followed eastward for 11 miles to the mine. Silver City, N. Hex., is about 50 miles northwest of the mine and may be reached by several routes.The White Eagle patented claim was owned by L. H. Duriez of Vanadium, N. Mex., W. D. and W. A. Howard of Deming, N. Mex., Alvan N. White of Silver City, N. hex, and: Mrs. E. M. Saunders of Los Angeles, Calif. D. P. McCabe of Lordsburg, N. Mex., a former lessee, has recently contracted to purchase the property.The White Eagle claim was located about 1920 and was patented in November 1933. It was leased to Cooper Shapley of Deming, N. Mex., in July 1933; to General Chemical Co. from August 1938 to May 1940; to Antonio Cristo from October 1940 to the fall of 1942; and f is ally it passed into the hands of D. F. McCabe of Lordsburg, N. Mex., in May 1945.Approximately 25,000 tons of fluorite ere containing about 65 percent CaF2, have been mined and shipped from this property.5/ Most of this ore was mined by Cooper Shapley and the General Chemical Co. and shipped to the General Chemical Co.'s La Purisima mill at Deming. No exact data on production are available."

Jul 1, 1946

By Robert L. Kranz

Mining-induced microseismicity data collected by the U.S. Bureau of Mines in a hard-rock mine were analyzed for spatial and temporal patterns that might prove useful for prediction of rock bursts or assessment of rock mass damage changes. Pattern attributes described and illustrated in the previous report (part 1) were applied to the study of aftershock sequences associated with two different stopes. The aftershock sequences were spatially and temporally fractal, and the fractality was maintained for up to 16 h following a sequence progenitor. This suggests mechanical interdependency among the after-shocks. No statistical difference was found in the distributions of fractal dimensions when comparing two different stopes or when comparing aftershock sequences initiated by blasts or bumps. This suggests a lack of sensitivity to both stress perturbation mechanism and local damage states. However, differences between the two stopes were found in other sequence attributes that support inferred differences in the magnitude of stress concentrations and damage near each stope, and over time as a stope is developed.

Jan 1, 2010

By W. R. Huff

This report describes the development and operation by the Bureau of Mines of a pilot plant designed for using high-volatile A bituminous coal-in-water suspensions as a source of preheated coal and superheated steam in the pressure gasification of coal with oxygen. Figure 1 on page 2 is a block diagram of the integrated gasification process, in which a total of 70 tons of coal was fed from slurry and gasified. The present work included (1) development of equipment and methods both for mixing pulverized coal and water to produce slurry and for pumping and metering the slurry at gasification pressure; (2) development of equipment for heating the flowing slurry and, because slurry that can be pumped produces more steam than is necessary as a gasification reactant, developing equipment for removing and metering the excess steam; and (3) demonstration of the process under actual gasifier operating conditions, at a coal rate of about 800 pounds per hour and gasification pressures in the range 100 to 300 pounds per square inch gage. By using the forced-convection principle, a flow of slurry made from a caking, high-volatile A bituminous coal can be continuously heated to 600° F. in a coil-type heater. The flow rate and concentration of the slurry and the temperature gradient along the length of the heating coil must be closely controlled. In a radiant-type heater, involuntary reductions in flow rate, even momentary, can lead to coking and plugging of the heater coil.

Jan 1, 1961

By Robert L. Skaggs

Sixteen nonaqueous techniques conceived to replace the current aqueous scheme for separating hafnium and zirconium tetrachlorides were re- viewed and evaluated by the Bureau of Mines. The methods are divided into two classes: separation by fractional volatilization of the tetrachlorides, which takes advantage of the higher volatility of hafnium tetrachloride; and separation by chemical techniques, based on differences in chemical behavior of the two tetrachlorides. The criteria used to evaluate separation methods were temperature, pressure, separation factor per equilibrium stage, complexity, compatibility with existing technology, and potential for continuous operation. Three processes were selected as being most promising: (1) high-pressure distillation, (2) extractive distillation from a molten salt, and (3) preferential reduction of gaseous ZrC14. Any of the proposed nonaqueous Hf-Zr separation schemes must be supplemented with additional purification to remove trace impurities.

Jan 1, 1984

By William H. King

The property of the Cupric Mines Co. is situated in the San Francisco mining district, Beaver County, Utah, 21 miles westerly from Milford (fig. 1), the rail and supply center for the area. Scheelite mineralization was not discovered until 1941, although the occurrence of lead and copper minerals had been known previously. S. VI. Hobbs, of the Federal Geological Survey, examined the Cupric property in November 1941 and prepared topographic and geologic maps of the area. This work was supplemented by additional investigations in January 1943 and March 1944 (fig. 2).

Jan 1, 1949