Search Documents

By David Schlain, C. B. Kenahan, F. X. McCawley

The electrodeposition of protective coatings of tungsten from a sodium and lithium borate - tungstate - tungstic oxide fused salt electrolyte was investigated . Soluble tungsten anodes were employed . Deposits were made on molybdenum , Carpenter 20 stainless steel , Inconel , and nickel . An atmosphere of argon was maintained around the electrolytic cell , and the electrolyte was stirred by rotating the cathode . Thick deposits of tungsten (up to 26 mils ) were made at a temperature of 900 ° C and cathode current densities of 0.3 to 0.4 ampere per square inch with high current efficiencies . The effects of variations in temperature , current density , electrolyte agitation , and tungstic oxide content of the electrolyte and of the presence of impurities such as moisture , air , iron , and nickel were investigated .

Jan 1, 1964

By C. R. McCann

The Bureau of Mines conducted an experimental study of conditions needed to produce flames of pulverized coal when the heat needed for ignition is sup-plied only from the flame and hot furnace refractory. An electrically heated furnace which burned about 1 pound of coal per hour was designed and fabricated. A sheath of air, surrounding the primary coal and air stream, was used to prevent entry of hot gases from recirculating combustion products. Furnace temperatures needed for ignition ranged from about 1,8300 F for an Illinois coal to 2,250° F for a Beckley seam coal. Apparent flame velocities were about 2 to 5 feet per second, increasing with volatile content of the coal and with distance from the burner mouth to the flame. The time required for ignition, approximately 0.02 to 0.07 sec, was a better measure of flame behavior than was velocity.

Jan 1, 1969

By D. L. Nussear, W. E. Wallace, N. N. Clark, M. Gautam, G. Hong-Guang

"Results from a study directed towards identifying and measuring the mutagenicity of diesel exhaust particulate matter involved in mining exposures, especially those which may synergistically affect genotoxic hazard, are presented in this paper. Particulate matter emissions from a diesel engine, representative of the ones found in underground mines, were sampled and assayed to determine the genotoxic potential as a function of engine operating conditions. Diesel exhaust was diluted in a multi-tube mini-dilution tunnel and the particulate matter was collected on 70 mm fluorocarbon coated glass fiber filters as well as on 8"" x 10"" hi-volume filters. A six mode steady state duty cycle was used to relate engine operating conditions to the mutagenicity potential.Protocols developed for using a primary component of pulmonary surfactant as a medium for collecting and applying respirable particulate material to cells for mutagenicity testing offer a true representation of in-vivo delivery of such respired aerosols to pulmonary cells and the genetic material within . The surfactant dispersion technique is discussed in this paper. Methods have been developed to sample and assay the diesel soot and diesel soot/mineral dust complexes which would not compromise the surface and physical properties of the particulate material."

Nov 1, 1995

By James A. Wasson

The Mitchell and Berea sands were cored and logged in Fred Link well K-l, Lower Newport field, Washington County, Ohio. Core and reservoir fluid analyses and available field data were studied to determine if these sands could be successfully waterflooded. The results of the study indicate that there is insufficient oil in place to form an oilbank in either the western Mitchell pool or the Berea sand, and that no commercial recovery of oil by waterflooding can be obtained in these reservoirs.

Jan 1, 1967

By G. L. Oldright

As sponge iron is much like porous, coarse sand, it is a tempting material to use in place of coarse scrap iron as a precipitant of metals, for scrap iron is relatively awkward to handle and exposes only a small amount of surface to pregnant solutions. The results of the experiments described in this bulletin are largely a record of the behavior of sponge iron as a precipitant of lead and copper under laboratory conditions comparable to those that would obtain in a commercial plant were it attempted to secure the maximum contact of surface between solution and precipitant. Physically, the study is largely one of the rates of diffusion of the metal ions in the solutions and through the metallic coatings surrounding the sponge iron particles. The practical objectives are to remove completely the valuable metals from solution and at the same time to obtain a precipitate of good grade. In order to fulfill this latter requirement, the precipitant should be almost completely consumed. These practical ends are usually secured by having the two substances involved pass each other counter-currently-that is, in such a manner as to have the strongest precipitant in contact with the most impoverished solution, and vice versa. EXPERIMENTS WITH LEAD SOLUTIONS In nearly all of the schemes involving the leaching of lead from its ores the metal has been put into solution as the chloride, and fairly concentrated liquors have been employed. The solubility of lead under such conditions is comparatively small at best; the hot pregnant liquors from which the metal is to be precipitated are then made nearly saturated with respect to lead, and only a very small amount of acid is used. Therefore it was not as necessary to learn the behavior of the sponge iron in precipitating lead from solutions of widely differing composition as to learn under what conditions, and with what mechanisms, this precipitation might be carried out most readily.

Jan 1, 1928

By Jr. Koch

As a part of a larger study of the distribution of metals within ore deposits, the geometry of distribution of gold, silver, lead, copper, and zinc in five veins of the Fresnillo mine, Zacatecas, Mexico, was established. The purpose was to obtain basic data necessary for evaluation of geological theories about processes of vein formation and useful for practical mining applications in ore estimation and prediction of ore beyond present workings. The Bureau of Mines investigation comprised statistical analysis of 64,000 assay values from some 16,000 mine samples. The samples were taken at 2-meter intervals in drifts exposing the veins through a vertical range of some 750 meters. Within individual veins, the metals are distributed in dome¬like patterns with highest metal contents tending Lo occur in oreshoots at the centers of the developed parts of the veins. However, in the block of ground containing all five veins, base metals define mathematical domes with highest contents near the center; precious metals define mathematical basins or troughs with low contents near the center. The ratio of silver assay values to lead assay values corresponds to two geographically distinct types of mineralization: one in which silver is closely related to lead, and another in which silver is independent of lead. Other metal ratios also vary regularly from one place to another. The statistical methods employed in this study would be useful for other geologists or engineers who need to analyze large amounts of assay or similar numerical data.

Jan 1, 1967

By Joseph A. Cavallaro

This report describes the timed release analysis technique that was developed to serve as a tool for assessing the froth flotation cleaning potentials of fine-size coals. Using this developed technique, 16 coals from 10 different coalbeds were tested. All of the coals included in this study were quite amenable to froth flotation with float coal yields ranging from 80.7 to 99.5 percentage points. Float-and-sink analyses of the coals tested are shown to be of limited value in predicting froth flotation cleaning potential. Generally the float-and-sink analyses indicated a better product could be obtained than froth flotation could provide; although, in four of the coals tested froth flotation results were superior to those expected from the gravimetric analysis. The fixed carbon content of the samples collected was found to correlate with the floatability of the coals. The higher rank coals were the most readily floatable coals while the lower rank coals did not respond quite as well to flotation.

Jan 1, 1965

By R. L. Levens

Researchers at the U. S. Bureau of Mines conducted investigations to evaluate the potential for ground water contamination by mine waste used as backfill. Samples of cemented waste backfill and water discharging from drillholes and seeps were collected to use in chemical analyses and laboratory tests to determine the physical and chemical factors that control release of heavy metals to ground water. Greater water retention by cemented backfill (as compared to uncemented sandfill) reduces the surface area exposed to oxidation, which in turn reduces the amount of acid produced. The acid is neutralized by the cement and minerals contained in the backfill. The grain-size distribution of tailings used for backfill affects the structural integrity of cemented backfill under attack by acidic water; breakdown of the backfill structure releases neutralizing materials faster. Backfilled stopes in rock with low hydraulic conductivities will constitute preferential flow paths after mine flooding; however, the rate of flow through backfill will be much slower than when the stope is partially saturated during mine operation. Considering all factors, acid generation and release of metal ions from cemented backfill should be less than in uncemented sandfill.

Jan 1, 2010

By Robert S. Sanford

In April 1948, the Bureau of Mines was requested to evaluate the graphite deposit' known as the Benjamin Franklin and Just mines in Chester County, Pa. After preliminary investigation, it was recommended that the Bureau core-drill, trench, and sample the deposit and make beneficiation tests on the ore. During the first and second World Wars, flake graphite was in short supply, and a number of deposits in the United States were exploited. In 1942, the Defense Plant Corporation, through its lessee, the Benjamin Franklin Graphite Co., purchased 70.263 acres of graphite-bearing land and built a complete mining and milling plant with a capacity of 300 tons of crude ore per 24-hour day at a cost of $426,250 (Plancor No. 1254).

Jan 1, 1949

By James F. Neill, O&apos

Investigation of the Gilley fluorite deposit was based upon examinations made by several of the Bureau's mining engineers. Fluorspar was found in the dump talus of sloughed and water-filled trenches and shafts, and there were indications that faulting or other dynamic distortions favorable to deposition of this mineral in minable quality and quantity might exist. The inference was based upon a field study of the area and its comparison with fluorspar deposits in Kentucky. The proximity of this deposit to the iron furnaces at Gadsden and Birmingham was a factor that influenced its investigation, as the demand for metallurgical grades of this critical mineral is acute. The present supply for the district is obtained from out-of-State sources, and the value of any local deposit would be enhanced by the saving in freight charges. The Gilley fluorspar deposit is 17 miles east of Gadsden and 50 miles northeast of Birmingham, Ala. Mineral deposits occur as thin veinlets and small bunches of fluorite in upturned bode of siliceous limestone. The ore-bearing structure is a reverse fold, and the mineral deposit appears as a replacement along crumbled zone fractures of the contorted limestone.

Jan 1, 1950

By A. Wahab Khair, N. P. Reddy

"INTRODUCTION The continuous mining machines which were introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners which were designed for increased productivity have also increased the concentration of respirable dust in mines. Inhalation of this respirable dust by miners causes the Coal Worker's Pneumoconiosis (CWP). Concern for CWP increased in the United States following a 1963-65 survey that showed definite x-ray evidence of CWP in 9.8 percent of working miners and in 18.2 percent of nonworking miners in the Appalachian bituminous coal region (Breslin and Niewiadomski, 1982).One of the major objectives of the Federal Coal Mine Health and Safety Act of 1969 was the prevention of CUP. This law initially limited the daily average exposure of coal miners to 3 mg/m3 of respirable dust. However, following the results of a probabilistic model developed by Jacobsen, et. al. in 1971, the limit was reduced to a mass concentration of 2 mg/m3 unless quartz content exceeds 5 percent, a rare occurrence in mines. Based on x-ray categorization prior to death it is believed that the mass concentration in the respirable fraction is a parameter of primary interest for hygenic evaluation of dust exposure. Morgan, Burgess and Jacobson (1973) suggested that the quantity of inhaled dust, although influential is not the only aspect of exposure which is significant in producing CWP. Miners working in higher rank coal (anthracite) mines are more susceptible to CWP (Morgan, Burgess and Jacobson, 1973). This also confirms the findings of the British (Bennett, Dick and Kaplan, 1979 and Hurley, et. al., 1979) and Germany (Reisner and Rubock, 1977). Based on the cytotoxicological evidence Reisner and Rubock (1979) suggested that when coal properties are similar, increasing quartz and mineral content increases toxicity. David, Ottery and Le Roux (1975) examined that as the severity of the CWP increased the retention of the coal dust content in the pulmonary region remained the same, while that of quartz content increased significantly. Leiteritz, Baur and Bruckman (1971) studied the various components of coal dust and showed that coal particles comprised a smaller fraction of the mass of fine dust than did particles of quartz and minerals. It is ironic that quartz and mineral matter both comprise smaller fractions of the higher rank coal dust (Dodgson, et. al., 1971 and Dwiggins, 1981). Results of a recent research revealed that quartz or any other mineral examined had no strong or consistent effect on the incidence or progress of CWP (Attfield, 1984) while Dodgson, et. al., (1971) concluded that high exposures to minerals such as illite, kaolinite and mica will retard the progress of CWP. Size and shape characteristics are believed to be important in the relationship between mineral particles and health effects (Shedd, Virta and Wylie, 1982)."

Mar 1, 1989

By William D. Riley

In order to evaluate the corrosion resistance of zirconium in mineral extraction processes, such as a clay-hydrochloric acid leaching process for extracting alumina, the Bureau of Mines conducted corrosion studies in HCl-AlC13-FeC13 environments. A series of weight loss and electrochemical tests were conducted at 25° and 65° C in aluminum chloride (AlC13) plus hydrochloric acid (HCl) solutions containing 0 to 1,000 ppm ferric ion. It was determined that zirconium, which normally exists in a passive state in chloride-containing solutions, undergoes pitting attack in solutions containing more than 100 ppm of ferric ion. It is also shown that an oxide film prepared in air at high temperature offers protection in acid solutions containing levels of ferric ion from 300 to 1,000 ppm.

Jan 1, 1981

By H. M. Thorne

The oil-shale deposits of the Puertollano basin in the Spanish province of Ciudad Real appear to have been give little consideration in discussions of oil-shale resources throughout the world. A small, integrated oil-shale operation has been conducted at Puertollano since about 1922 by a French company, Sociedad Mimora y Metalurgica de Penarroya, hereinafter referred to as "Penarroya", but only within recent years have the potentialities of the Spanish oil-shale deposits been recognized. Empresa Nacional "Calvo Sotelo" do Combustibles y Lubricantes, hereinafter designated as "Calvo Sotelo," which was created in 1942 by the National Industrial Institute of Spain to produce liquid fuels from oil shales, has made marked progress in the design and construction of a complete oil-shale plant at Puertollano. Penarroya is mainly a coal-mining company, and the oil-shale operations were on a small scale of approximately 220 tons a day in October 1947. It is an integrated operation comprising oil-shale mining and retorting and shale-oil refining. Motor gasoline, Diesel fuel oil, light burner fuel oil, lubricants, paraffin wax, cresols, and ammonium sulfate are manufactured.

Jan 1, 1950

By William E. Young

There are many large rhodunite-bearing veins containing manganese in the Eureka-Animas Forks area of the San Juan Mountains in Colorado. The Sunnyside vein is the largest known vein in the area. As observed on the surface, the vein is mineralized over 8,000 feet and attains a maximum width of 200 feet. The average width of the vein and its branches and ramifications is 58 feet in the area that was mapped in detail. The weighted-average analysis of surface and underground samples from the northeastern extension of the Sunnyside vein is 8 percent manganese. Most other known veins in the area have a similar manganese content. The Hidden Treasure vein lies southeast of the Sunnyside-No Name-Mastadon vein. The weighted average of the analyses of surface and underground samples from this vein is 13 percent manganese. Exposures of the Scotia-Silver Chord vein are visible over a strike length of 4,000 feet on Treasure Mountain. Diamond-drill holes show that the vein contains 10 percent or more manganese to a depth of 400 feet. The vein has an average width of 28 feet. The Independence vein is exposed on the surface for a distance of 600 feet and has an average width of 6 feet. Three cut samples taken across the vein had an average content of 20.7 percent manganese. Sampling of the outcrops of eight veins in the Placer Gulch area also indicates manganese. Numerous other veins cropping out in the surrounding area are similar to the outcrop of the. Sunnyside vein system mineralogically and are worth investigating.

Jan 1, 1966

By Lloyd Williams

1. The investigation shows that the Sewanee bed is the only bed of major importance in Marion County, 97 percent of the coal mined in the county having come from this bed. There are coal reserves in minor quantity in the Battle Creek bed, and production from this bed depends on a few small truck mines. The Richland bed, or Lower Sewanee, has been mined in the past, but no coal has been produced from it in late years. There are no production records of any other beds in the county, although same coal has been produced from them. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated to be 61 million short tons as of January 1, 1953. Of this total, 55 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate where available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By Alex C. Smith

This report describes laboratory studies conducted by the Bureau of Mines on the spontaneous combustion of U.S. coals. Approximately 11 pet of U.S. underground coal mine fires are attributed to spontaneous combustion. The relative self-heating tendencies of 24 coal samples were evaluated in an adiabatic heating oven. Minimum self-heating temperatures (SHT's) in the oven ranged from 350 C for a lignite and high-volatile C bituminous (hvCb) coal, to 1350 C for two low-volatile bituminous (lvb) coals. An empirical expression was determined predicting a bituminous coal's minimum SHT in the adiabatic oven based on the coal's dry ash-free oxygen content. Several factors that can affect the self-heating process were also evaluated. The self-~eating tendency of a coal increased when the coal was dried and exposed to humidified air, and was dependent on the particle size and oxygen concentration of the air. A new moderate-scale apparatus is described, in which the self-heating tendencies of larger coal samples, 3 kg, can be evaluated. The minimum SHT's of two coals were determined and the results were in good agreement with those found in the adiabatic oven. Finally, results of a test in the moderate-scale apparatus indicated a strong dependence of the self-heating rate of a low rank coal on the moisture content of the air.

Jan 1, 1987

By August J. Kwitowski

This report presents the results of a joint Bureau of Mines-U.S. Department of Energy project that evaluated a newly developed low-coal mining system: the 4M miniminer system. The evaluation took place from April through October 1981 and determined potential health, safety, and productivity factors for the mining system using the surface test facilities at Bruceton, PA. The planning, testing, results of testing, and a summary evaluation of the 4M miniminer system are included in the report. The miniminer system was found to be a very good concept with future potential for safe, healthful, and economic production in thin-seam mining. The mining system was also judged to have considerable potential for use in some coal seams that are presently considered unminable by other existing mining equipment. The preproduction, prototype version of the miniminer system that was tested suffered from several safety and production problems. These problems are also described, along with suggested remedies.

Jan 1, 1989

Geological discontinues in the coalbed, such as faults, sandstone channels, permeability facies, lithotype changes, and large scale partings in the coal seam, can cause intermittent production problems or produce unexpected amounts of water or gas from degasification boreholes. These discontinuities not only can impact methane emissions into the mine workings, especially if they hinder proper and effective degasification of the coalbed but may act as conduits for methane flow from gassy strata into advancing mine workings. The effects of these discontinuities are still under debate by mining and gas production experts. This study presents a numerical investigation using reservoir simulations of the effects of partings and permeability facies and lithotype changes on the production performances of vertical and horizontal degasification boreholes, as well as the emissions during longwall operations. In this work, the grid block was designed in a multi-layer 3-D structure which enabled spatial descriptions of the geometries and properties of the discontinuities within the coal seam. The studied coal seam discontinuities and their properties were distributed arbitrarily within the model. Production was simulated by vertical and horizontal boreholes. Degasification boreholes operated two years prior to start of the mining. The results of this numerical study show that in coal seams with major heterogeneities and discontinuties, the geometry and location of the boreholes are important for improved gas production. These considerations are also important for controlling methane and water inflow into the working environment during longwall mining.

Jan 1, 2008

By Peter N. Gabby

In 1990, the Bureau of Mines conducted a mineral resource investigation of the 12.321 acre Black Warrior study area, one of several proposed additions to the Sawtooth Wilderness. No identified mineral resources were delineated. There were 123 lode and placer claims in or adjacent to the study area. There is a known hot spring adjacent to the study area, but presently no geothermal leases are pending. Lode mines in pr adjacent to the Black Warrior study area have produced 4,022 tons of ore from which 1,981 oz of gold and 811 oz of silver were recovered. None of the vines are currently active. During the field study 125 rock samples were taken. Significant gold assays and favorable geologic characteristics at seven properties indicate that gold occurrences and resources with byproduct metals may exist in the study area. Two other sites yielded anomalous gold assays; however, sage favorable geologic characteristics are lacking. Presently, identified gold resources are being delineated by drilling programs in the nearby Atlanta and Rocky Bar mining districts. These districts have geologic characteristics similar to the Black Warrior area. During the field study 22 placer samples were taken. In most places where an anomalous concentration of gold was found, the stream channels are too narrow for operations other than recreational suction dredges. However. One area is estimated to contain over 2 million yd3 of gold-bearing gravels.

Jan 1, 1992

By G. T. Krempasky

This report covers the installation and evaluation of lb reinforced concrete sets, 6 in each of 3 mines in the Goeur d'Alene mining district, Shoshone County, Idaho, and is the second of a series to determine the feasibility of a more permanent type of mine support. Closure measurements, where applicable, were made periodically of the concrete-set installations and were compared to the initial cross section of the sets. A different method of blocking was used at each test site; at one test site the type of blocking was changed several times during the test. Results from each test site are reported separately. No attempt was made to compare the cost of the concrete installations with the cost of other types of support used in the district. Such an evaluation of permanent types of support would require a longer period of time. At this time, tests are not complete enough to determine the applicability of underground concrete supports. However, results to date tend to confirm the general opinion that precast concrete mine supports could be used to advantage in openings that require support and must have long life, especially where decay of timber is an important factor.

Jan 1, 1963