Search Documents

By S. Stephen Uslan

The purpose of the study was to demonstrate the effect of positive reinforcement, specifically, social reinforcement (SR), on the frequency of eye, hand, and back injuries at four experimental salt mines. Injury data was collected from January, 1976, for the prePOMOST period and from the onset of training to September, 1978, for the post-POMOST period. All data was collected on a month-by-month basis. For the training period approximately 100 managers and supervisors from five plants were trained in the use of positive reinforcement for occurrences of "safe behavior." Each supervisor was also provided manuals and other supportive materials. Additionally, following training, all supervisors were provided some coaching experience to keep the knowledge and capabilities gained during training from being extinguished. The analysis showed significant injury reductions in two sites and no injury reductions in the other two. When the injury data was corrected for the additional man hours expended in the postPOMOST period, a third site showed reduction in injuries. Similar findings were shown when the experimental sites were compared to other sites in the industry. The results were interpreted to support the hypothesis that the application of social reinforcement is related to a reduction in injuries.

Jan 1, 1978

By R. Karl Zipf

A fatal explosion in a sealed area at the Sago Mine in 2006 prompted researchers and regulators in the United States to re-examine the requirements for explosion-resistant mine seals. Seals are used in underground coal mines to isolate abandoned mining areas from active workings. Prior to the Sago disaster, mining regulations required seals to withstand a 140 kPa explosion pressure. Recent research at the National Institute for Occupational Safety and Health (NIOSH)Pittsburgh Research Laboratory showed that pressures from explosions can far exceed this pressure. U.S. mining regulations now require much stronger seals. Current research focuses on understanding the science, engineering and management of sealed areas of coal mines. Scientific efforts seek understanding of how explosive methane-air mixtures accumulate using measurements and models of the sealed area atmosphere. Additional scientific efforts aim to understand the explosion pressures that can develop using a combination of numerical modeling and experiments. Engineering efforts aim to produce design guidelines for seals that can resist the new higher pressure design criteria. NIOSH researchers are also developing guidance for monitoring of sealed area atmospheres and inertization of potentially explosive gas mixtures within sealed areas. This paper seeks to encourage scientific discussion among international peers since preventing explosions within sealed areas is of interest to underground coal operators and regulators.

Jan 1, 2009

By R. A. Guidotti

The Federal Bureau of Mines studied the thermal decomposition of the nitrides of the Group V A metals (CbN, Ta3N5, and VN) with the goal of preparing high-purity metals. Solid-state purification and arc and electron-beam melting were examined. Electron-beam melting proved to be the most efficient means of nitrogen and oxygen removal. Columbium and tantalum of 99.9-pct purity were prepared by this technique; in the case of vanadium, however, nitrogen could not be reduced below the solid-solution level.

Jan 1, 1976

By Susan M. Moore

Many challenges are faced by workers in lower-seam (42 inches or less) mines. The lower-seam heights confine mine workers to their knees as they perform their daily tasks such as installing roof bolts, delivering supplies, repairing belt, or cutting coal. Miners working in these lower seams often consider kneepads to be their only line of defense against knee injuries. However, healthy knees do not start and stop with kneepads. Other interventions such as changing postures, proper hygiene, and work station design may also be used to reduce mine workers? risks for developing knee injuries. Incorporating these and many other interventions into a mine worker?s ?way of life? is an important step to ensuring a long, healthy career and retirement. Keeping knees healthy is also a key aspect to reducing costs in low-seam mines as the industry battles rising health care costs, and training/recruitment of replacement workers is time-consuming and costly. Educating the workforce about the possible interventions to reduce knee injury risk is a primary objective for the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory (PRL). Therefore, NIOSH researchers, along with industry and academia, developed a training package to educate the mining com­munity about some possible interventions beyond kneepads that may be used to help decrease knee injury rates. Increased awareness and simple changes are the first steps to reducing knee injuries.

Jan 1, 2008

By P. Nicholls

[This paper sets forth the burning characteristics of coke used as a domestic fuel as shown by work of the U. S. Bureau of Mines and others. Coke is a truly smokeless solid fuel and is held in high regard for this quality. Ways are being found for making commercial coke from a wider range of cools than heretofore, and tale use of coke for domestic heating is increasing. ACKNOWLEDGMENTS The experimental work reported in this paper was conducted at the Pittsburgh Experiment Station of the U. S. Bureau of Mines cinder the authority of O. P. Hood, chief mechanical engineer; M. L. Orr, assistant feels engineer, and W. M. Brewer, junior fuels engineer, assisted by Charles Schramm cooperated in making the tests.]

Jan 1, 1929

By Arnold B. Hubbard

This report presents a hydrogenolysis study undertaken to obtain information on the constitution of the kerogen or organic material in Colorado oil shale and to determine some of the properties of the hydrogenolysis products. The high yield of hydrogenolysis products was separated, so far as possible, into type compounds; a number were identified. The results thus obtained were used as a basis for proposing the possible existence of certain structures in kerogen. To the authors' knowledge, few or no hydrogenolysis studies have been made of Colorado oil-shale kerogen by others. However, this method has been used in studying the constitution of coal. In general, the coal studies involved treating pulverized coal at different temperatures and hydrogen pressures with different catalysts. In some instances different solvents were used during the treatments.

Jan 1, 1959

By Clarence A. Wright, JAMES T. NORTON, JAMES G. PARMELEE

The object of this paper is to give to mining companies and to all others who are interested some idea of the possibilities in the treatment, by differential flotation, of lead-zinc ores of the Coeur d'Alene region and other districts. The purpose of these investiga.. tions is not to evolve a differential flotation process that would replace present methods of gravity concentration but rather one that could be applied to the relatively fine material and slime produced in the mills and treated unsuc_pessfully by gravity methods or by flotation. It is expected, of course, that the products to be obtained by differential flotation would be of much better grade than those now produced by flotation in the Coeur d'Alene mills. In view of the fact that it has been difficult to obtain representative samples of flotation feed from the mills, owing to the necessity of shipping the material wet and free from oil or other foreign matter that might be deleterious to the differential separation of the sulphides, the writers have felt justified in running flotation tests with the mill feeds in order to ascertain whether a differential separation of the sulphides could be effected. However, two different lots of flotation feed were tested for differential flotation, and the results of tests of one of these are given in this report. It is hoped that it will be possible later to test out the flotation feed for differential flotation on a large scale in some of the mills. This paper covers part of the investigations carried on by the United States Bureau of Mines in cooperation with the Idaho Bureau of Mines, the University of Idaho, and certain mining companies of the Coeur d'Alene region. Although the results of the tests included in this report are not to be considered final, they indicate possibilities and may suggest others leading to a solution of the problem of separating lead and zinc sulphides by differential flotation in the treatment of certain ores.

Jan 1, 1921

By Philip C. Good

Preliminary studies showed that direct hydrolysis of H2SiF6 to SiO2 and HF at elevated temperatures was subject to many mechanical difficulties, and that corrosion of construction materials was a serious problem. Elimination of SiO2 from the HF product was generally poor. An alternative procedure, hydrolysis of lime-neutralized H2SiF6 by steam at 950° to 1,100° C, yielded a product very low in SiO2. Condensates containing up to 300 g/1 HF were prepared.

Jan 1, 1968

By D. S. Kingery

Investigations over several years have disclosed that the principal manners of occurrence of shuttle-car injuries are in order: 1. Victims in contact with roof or crossbars. 2. Victims in contact with ribs or timber legs. 3. Victims falling from, or jerked from, shuttle cars. 4. Victims in contact with overhanging brows or protruding pine for pin timbers, or water lines. 5. Contact with persons or collisions with parked equipment. 6. Victims injured by roof falls or falling timbers caused by knocking out roof supports with shuttle cars. 7. Victims injured by runaway shuttle cars. 8. Victims injured while loading or unloading timbers or other materials from shuttle cars. These recurring types of shuttle-car accidents reflect the physical conditions of the working sections, certain safety deficiencies in shuttle-car maintenance and design, and unsafe practices by operators.

Jan 1, 1952

By Brian R. Zelenka

The Bureau of Mines (Bureau) reviewed all available information regarding geologic and depositional processes contributing to potential coastal and offshore platinum group metal (PGM) placer deposits around the Goodnews Bay Mining District. The Bureau found that favorable environments for PGM along with gold and chromite enrichment include: (1) buried paleofluvial channels; (2) recent paleofluvial channels with little marine sediment overburden, (3) beach deposits, particularly in the upper swash zone and near back beach environments; (4) paleostrand lines; (5) shoal lag deposits inside the mouths of Goodnews and Chagvan bays; and (6) bases of far offshore tidal ridges which may represent reworked glacial deposits. Limited geologic and compositional (assay) data prevent determination of deposit size and grade of PGM mineralization for each deposit class. Future geologic sampling requirements for demonstration of identifiable offshore and beach PGM-bearing placers are discussed. Beach and offshore sampling programs conducted by the Bureau in 1986 will contribute additional information providing verification of specific deposit classes.

Jan 1, 2011

By R. V. Lundquist

Aeration in water slurries and controlled drying of manganous hydroxide produced from dithionate leaching of Artillery Peak manganese ores from Arizona were investigated by the Bureau of Mines at its Electrometallurgical Experiment Station, Boulder City, Nev., to determine whether a simple process could be developed for converting this product into a battery-grade manganese dioxide. The properties of manganese dioxide prepared by the thermal decomposition of manganous nitrate were investigated also. Manganese dioxide suitable for use in batteries was not obtained from the dithionate leach product, but some of the factors controlling its oxidation were isolated. Aging of manganous hydroxide was of major importance in retarding its oxidation by aeration. Sodium hydroxide and sodium silicate promoted oxidation by drying. Optimum quantities were about 0.85 mol of sodium hydroxide and 0.2 mol of sodium silicate per mol of manganese, and drying temperatures of 200° C. produced yields of manganese dioxide up to 90 percent of the manganese present. Higher temperatures and concentrations of reagents carried oxidation of manganese beyond its tetravalent state.

Jan 1, 1957

By R. F. Linfield

Figure 1-1 shows the basic transmitter design concepts used for the pulse system, the half-wave CW system, and the full-wave CW system. The antenna current waveform is also shown for each transmitter for typical operating frequencies and antennas. The switches shown in Figure 1-i were actually implemented using solid state devices. In all three systems the signaling format may be interrupted to conserve power and thereby extend battery life. Frequency accuracy and stability is achieved using a tuning fork oscillator in the transmitters and tuning fork filters in the receivers for all three systems. This provides the narrow reception bandwidths needed to enhance signal detectability. All three systems also use frequency assignment for identification purposes. The location schemes employed are likewise identical, each being based on detecting the null (signal minimum) of the horizontal magnetic field on the surface. Since these systems are basically similar, the primary purpose is to select the system which gives the maximum signal detectability on the surface from a manpack transmitter operating in the mine. Both the pulse and half-wave C W systems use a d. c. pulse to energize the loop antenna. However, with the pulse system, this pulse duration is short compared to the pulse repetition rate (prf), whereas with the half-wave C W system the pulse duration equals one-half the period of the switching frequency. In the pulse system, energy from the battery is stored in a capacitor so that during the switching interval the internal resistance of the power source can be considered almost negligible. Both transmitters must drive a loop antenna which is a reactive load having inductance, L, and resistance, Ra.

Jan 1, 1973

By A. J. Barry

Recent developments in mechanizing longwall it mining in Europe have aroused considerable interest among American coal-mine operators because this method provides an opportunity to improve safety, production, efficiency, and recovery. The success of longwall mining in Europe has depended to a large degree on development of effective roof-control systems. One of the major contributing factors in designing these systems is development off improved supports, which combine high load-bearing capacities with controlled yield characteristics, to use in the face areas. Other factors that relate to successful longwall mining involve knowledge of the structural properties of the strata above end below the coal bed being mined, movements of these strata induced by mining, and effects of the strata movements on the strata itself, as well as on the support system used. Extensive studies of the above factors relating to long-wall mining have been made in coal-mining countries abroad, and corresponding studies (1, 2, 3, 4, 5)3/ of room-and-pillar operations have been made in this country. Although descriptions and results of experiments of mechanized longwall operations in the United States have been published (6, 7, 8), this is the first instrumented study of roof behavior on a longwall operation. In view of the possible widespread application of this method of mining to American coal mines, where underground mining conditions are different from those found in European mines, an investigation was conducted at a mechanized longwall operation inn the Lancashire No. 15 mine, Barnes & Tucker Co., Cambric County, Bakerton, Pa., to study the factors that affect roof control. This report describes this investigation and discusses the results. ACKNOWLEDGMENTS This investigation was made under a cooperative agreement between the Bureau of Mines and the Barnes & Tucker Co., Barnesboro, Pa., end was conducted in the Lancashire No. 15 mine located at Bakerton, Cambria County, Pa. The authors acknowledge the cooperation given by Richard Z. Todhunter, Sr., president, Richard T. Todhunter, Jr., general manager, and other mine officials and employees of the Barnes & Tucker Co. Mr. Edward Thomas, chief, Roof Control Section, Bureau of Mines, Washington, D. C., and Dr. Leonard Obert, chief, Applied Physics Branch. College Park, Md., collaborated in the planning and promulgation of the program investigation.

Jan 1, 1954

By J. M. Goris

The U.S. Bureau of Mines is conducting research on cable bolt ground supports to assess their material and support properties, to provide design criteria for using cable bolt supports as roof control systems under various types of underground mining conditions, and to provide a mathematical model of cable bolt support systems. Part 1 describes laboratory studies of the support properties of cable bolts made of conventional steel cables and provides recommendations on such topics as the use of thick grouts, selection of breather tubes, and reduction of water bleeding in cement-based grouts. The studies evaluated both single and double cables; effects of different embedment lengths, water-cement ratios, and grout curing temperatures on support strength; effects of use or nonuse of breather tubes; pumpability and water-bleeding properties of grouts; and the strength properties of sand-cement grouts. Part 2 will cover the strength characteristics of birdcage cable bolt supports, epoxy-coated cables, and cables with steel buttons attached.

Jan 1, 1990

By J. L. Eakin

The Bureau of Mines determined agents that are effective in foaming heavy brines and oil from gas wells in severe concentrations of sodium chloride, in severe concentrations of calcium chloride, or in moderate oil-brine mixtures. Dynamic foam tests were designed to select the more effective foaming agents. Numerous foaming agents were tested in concentrated simulated brines, in oilfield brines having varied concentrations of ions, in heavy natural brines, and in a commercial brine generally used as a reservoir pressure-balancing fluid. Several agents were detected that could perform efficiently in the field under the most severe saline conditions. Agents that promote foaming in oil-brine mixtures were also determined.

Jan 1, 1965

By E. S. Leaver

The gold that is not recovered by a particular process is refractory to that process. A study to determine how the refractory gold is associated in the ore constituents usually indicates the needed improvement in the process or additional methods for bettering recovery. In preliminary work, segregation of the various minerals, gangue or impurities, and data showing the reactions of each in the recovery method readily confines the refractory gold to a certain part on which extensive research can be directed. In this dissecting plan, the microscope is an important aid in locating the refractory gold but should be supplemented by chemical tests. Each ore is an individual problem until the association of the gold has been determined. Knowing the problem through the interfering minerals or elements, the solution often is only the application of part of a former known practice as an auxiliary or additional feature. In the treatment plan for most gold ores, it has been the custom to try each of the usual recovery methods or combinations thereof, accepting the best results on a basis of the lowest cost. A better plan includes knowledge of the association of the gold and the various minerals from which it is to be recovered. This presents reasonable foresight into the problems that should be expected and permits some provision for avoiding probable difficulties. The preliminary work should include: Determination of the percentage of free gold with classification showing size of gold particles to be expected; determination of the percentage of gold associated with each mineral and whether it be freed from the mineral by crushing; and an analysis of representative samples of the ore to include other valuable minerals and the form in which they occur.

Jan 1, 1934

By H. C. Young

This paper deals with roof bolting in Alabama coal mines and iron-ore mines from the time it was introduced in early May 1948 to May 1, 1953, a 5-year period. The Tennessee Coal & Iron Division of the United States Steel Corp. began systematic roof bolting in early May 1948 in a coal mine and in an iron-ore mine, which had some of the poorest roof conditions in the Alabama mines. After the efficiency of roof bolting had been proved by the Tennessee Co. it was gradually adopted by other companies throughout the State, until in May 1953 approximately 53 percent of Alabama's total coal production and 100 percent of Alabama's total iron-ore production, mined underground, was being produced from roof-bolted areas. Statistics in this report will show the advancement made in roof bolting in the 5 years and also the amount of roof bolting that was being done as of May 1, 1953. Significant progress has been made in the coal and iron-ore mines of Alabama in reducing the roof-fall fatality rates during the past several years by adopting systematic roof bolting. The groundwork was laid through successful experiments early in 1948 by the Tennessee Coal & Iron Division of the United States Steel Corp. in cooperation with the Federal Bureau of Mines. This experimental work was based upon the previous experience of the St. Joseph Lead Co.2/ in its Southeastern Missouri mines.

Jan 1, 1954

By Margaret R. Egan

The Bureau of Mines experimentally burned Pittsburgh Seam coal and other combustible materials found in mines in order to obtain a better knowledge of their emission products. These experiments were conducted in the Bureau's intermediate-scale fire tunnel, which simulates environ-mental conditions in underground mines. Smoke characteristics, gas concentrations, mass loss, and ventilation were measured. From these values, heat-release rates, particle sizes, obscuration rates, combustion yields, and production constants were calculated. This information was sought as part of a comprehensive study of combustible materials that will ultimately advance the design of more efficient fire detection and suppression systems. The coal combustion measurements presented in this report, together with previous analyses of wood and transformer fluid fires form a data base by which future studies of other mine combustibles can be compared.

Jan 1, 1987

By Larry A. Haas

The U.S. Bureau of Mines, in cooperation with Cleveland-Cliffs, Inc. (Hibbing, MN), investigated ways of enhancing the quality (compressive strength, after-tumble and reducibility) of domestic acid and fluxed magnetite pellets by modifying the oxygen content during the preheat and induration periods of the firing operation . Oxidation of magnetite was best accomplished when sufficient oxygen and time were available before the peak induration temperature was reached. The rate of magnetite oxidation increased directly with the gas oxygen content during the preheat period at 7000 C and above. With 30 pct ( or more) O2 and a preheat rate of 2000 C/min, most of the magnetite was oxidized during the preheat period. With laboratory tube and mini-pot furnace tests, oxygen enrichment during the preheat period improved the pellet properties more in the simulated grate-kiln tests than in the simulated straight-grate tests. The longer induration period with the grate-kiln test resulted in more sintering of the residual magnetite and its reaction with the silicon compounds. When flux was present in the pellets, calcium silicates and calcium and magnesium ferrites were formed. More calcium ferrite was formed when the magnetite was oxidized early and less iron was present in the fayalitic calcium silicate slag.

Jan 1, 1993

By E. J. Gleim

To make a thorough survey of a coal mine in order to eliminate hazards, the competent safety engineer must be familiar with mere than one branch of engineering. It is essential that he know the properties of mine gases and the methods of detecting them, as well as hew to prevent dangerous as accumulations. It is also essential that he understand the action of overlying strata when the coal is removed, and the proper methods of protection by timbering or other suitable means of support. He must know the value of protective clothing in reducing injuries and mast be informed as to the correct handling and use of explosives to avoid premature blasts, misfires, and ether failures in blasting practice. He must understand hew to operate locomotives and cutting, loading, and various other types of machines to be able to recommend effective safeguards for protecting the men who use them in addition to being informed as 'to these and many ether activities connected with the mining of coal, he must net overlook electrical engineering if he wishes to combat the fire, shook, and ignition hazards attendant upon the use of electrical machinery and circuits in and around the mine intelligently. There are many points relating to safely in the selection, maintenance, and use of electrical circuits and equipment that are perfectly obvious to the electrical engineer but perhaps are not se evident to those not trained in this particular branch of engineering. Engineers of the U.S. Bureau of Mines who have made a special laboratory study of electricity as related to safety in minus haw e also made inspections of electrical installations at a large number of bituminous mines. These inspections have revealed practices and conditions that not only do not contribute to safety but that add nothing to efficiency and economy in the operation of the mine.

Jan 1, 1936