Search Documents

By Alvin Schallis

Of all the uses for dolomite that depend on its magnesia content, perhaps the most important is its use in basic refractories. The quantities of dolomite (including both that used as crude and that calcined before use) sold or used for refractory purposes by producers in the United States for 1920-41, inclusive, are shown in figure 1. As can be seen from the chart, the utilization of dolomite as a basic refractory is far from new; it was, in fact, the first basic refractory used extensively in open-hearth steel furnaces. After large deposits of magnesite were opened in Austria-Hungary, the use of dolomite in the open hearth declined somewhat, only to be actively revived during the World War of 1914 to 1918, when supplies from Austria were shut off. The use of dolomite as a refractory in the steel industry again declined slightly for a brief period after the Armistice, but subsequently its use has tended steadily to increase, latest statistics indicating that more dead-burned dolomite is used per ton of open-hearth steel now than during the World War of 1914 to 1918. Despite fluctuations in consumption, dolomite has continued to be by far the most widely used basic refractory material. The following table, showing the quantities of basic refractories consumed in the manufacture of steel, the principal outlet, indicates the relative importance of dolomite. The chief reason for the widespread use of dolomite as a basic refractory is its relatively low cost. Its abundance and the proximity of the deposits to the steel industry (see fig. 2) afford every incentive to enhance the desirable physical properties of dolomite refractories and to ameliorate certain of their less desirable characteristics. The present emergency, with its huge demands upon the steel industry, has lent further impetus to the work of improving dolomite refractories.

Jan 1, 1942

By Andrew Allan

During recent years underground production for the Pennsylvania anthracite region has reached the lowest output per man per day figure of the last decade and a half. This fact, combined with increased unit costs for labor and material, has forced the market price of anthracite ever higher. Over the years the mines have become deeper, and haulage distances have increased, thus adding to the mining costs. The industry now recognizes the need for new mining techniques to offset increasing costs. The Federal Bureau of Mines, through its Anthracite Research Laboratory, is engaged in a program of underground-mining research in cooperation with anthracite-producing companies to aid in reestablishing the economy of the region by introducing methods and/ or machines that will reduce underground-mining costs and, at the same time, enhance the safety of the workmen.

Jan 1, 1953

By A. E. Raddatz

The Federal Bureau of Mines, as part of its goal to minimize undesirable environmental impacts associated with mineral processing, has investigated a soda-smelting technique for processing ilmenite into pig iron and a titanium slag that is suitable for a feed to a sulfate-process titania pigment plant. By this procedure, the generation of ferrous sulfate waste and its associated disposal problem is obviated. Molten titania slag was quenched, water leached, and filtered to yield a sodium titanate intermediate product containing about 70 wt-pct Ti02, 1 wt-pct Fe, and 20 wt-pct Na20. This intermediate product, high-soda titanate (HST), was mixed with H2S04, calcined, quenched, and water leached to produce a low-soda titanate (LST) product that contained only 2 wt-pct Na20. Both the HST and LST were evaluated as feed materials for preparing titania by the sulfate process. About 95 pct of the Ti02 was extracted from HST and LST by digestion in concentrated or 50-wt-pct-H2S204 solutions. About 95 pct of the solubilized Ti02 was subsequently recovered from the titanyl sulfate solutions by hydrolysis. Barren solutions from hydrolysis, containing about 26-wt-pct H2S04, were upgraded by vacuum-thermal evaporation or electrodialysis. The regenerated acid solutions were used to digest additional HST and LST.

Jan 1, 1979

By Pete G. Kovalchik, Lynn A. Alcorn, Rudy J. Matetic, Adam K. Smith

Over-exposure to noise remains a widespread, serious health hazard in the U.S. mining industries despite 25 years of regulation. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. Mine Safety and Health Administration (MSHA) coal noise sample data collected from 2000 to 2002 show that 65% of the equipment whose operators exceeded 100% noise dosage is comprised of seven different types of machines. The continuous mining machine is first among all the equipment with 35% of the noise overexposures. The ational Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce excessive exposure for operators of continuous mining machines and preventing additional cases of oise Induced Hearing Loss (NIHL) by developing low-cost retrofit noise controls for mining equipment. This paper describes a noise control for reducing the noise overexposures of continuous mining machine operators. Underground results show a 26.4% and 27.4% noise exposure reduction for the continuous mining machine operator. This research is providing the mining community with an additional noise control to be utilized on continuous mining machines, therefore reducing operator noise overexposure. Utilizing this newly developed noise control, along with previously proven controls for the continuous mining machine chain conveyor, will provide operators of these machines an opportunity to be within the MS HA-Permissible Exposure Limit (MSHA-PEL).

By W. M. Myers

"The continued expansion of modern industry broadens the markets for minerals and their product. With these increasing demands new uses are being found for minerals that heretofore were considered as possessing no commercial possibilities. This tendency is reflected in the nonmetallic field in a constantly increasing demand for minerals formerly considered to be of scientific interest only, Furthermore, nonmetallic minerals of established commercial importance are used in new ways in various products, and this tends to expand the markets for these minerals. Some recent outstanding developments in applications of minerals are given in the following pages.The Andalusite GroupAmong the minerals that until recently were considered of scientific interest only, may be listed those of the andalusite group. This group is composed of the three minerals, andalusite, cyanite (or kyunite), and sillmanite, which are all forms of the compound Al2SiO5 (A1203, S1O2), and are therefore identical in chemical composition, but differ in physical properties,"

Mar 1, 1924

By J. F. Shultz

The Bureau of Mines investigated the hydrogenation of carbon monoxide and carbon dioxide over Raney nickel catalyst and nitrided fused-iron catalyst using both a single-pass and a recycle system. Activation energy over Raney nickel catalyst is 29 to 32 kcal/mole for synthesis from either CO or CO2, Pressure dependence of the gas conversion is to the 0.3 power for synthesis from CO and to the 0.5 power for synthesis from CO2. Nitrided fused-iron catalysts were tested using high recycle rates and 3H2+lCO, 2H2+lCO, and 1H2+lCO feed gas at 21.4 atmospheres absolute pressure. The relative usage of hydrogen (moles H2 consumed per moles Ha+CO consumed) was larger than in corresponding single-pass tests, and the relative usage of hydrogen approached the feed gas ratio monotonically as conversion increased. Activation energy was found to be 12 or 13 kcal/mole fresh feed gases of 3H2+lCO or 2H2+lCO. For single-pass operation the activation energy under the same conditions was 19 to 21 kcal/mole.

Jan 1, 1967

By L. B. Berger, S. J. Pearce

One phase of Bureau of Mines' work in health and safety is promotion of the use of safe, satisfactory, and reliable respiratory protective. devices. To insure that such devices will be available, the Bureau has established schedules of minimum requirements for self-contained breathing apparatus, gas masks, supplied-air respirators. (hose masks, air-line respirators, and abrasive blasting helmets, hoods, or masks), dispersoid (dust, fume, and mist) respirators, and nonemergency gas respirators (chemical cartridge respirators). Approval tests of self-contained breathing apparatus are conducted by the Safety Branch; approval tests of other types of respiratory protective equipment are conducted by the Health Branch. Both branches are in the Health and Safety Division.

Jun 1, 1950

By Gerald W. Elger

A new process under development by the U.S. Bureau of Mines for producing synthetic rutile from ilmenite is described. Rutile formation is based on oxidation and fluxing of titania slag produced by electric furnacing of ilmenite. Laboratory tests show that phosphorus pentoxide flux additions to oxidized slag enhance conversion to rutile by forming a phosphate-based glass matrix. This matrix contains most of the major impurities, including the oxides of iron, aluminum, magnesium, manganese, and silicon. Rutile crystals of 5 to 150 microns in size were formed in slags heated to temperatures of 800° to 1,550° C. The synthetic rutile crystals were liberated from ground slag by treating with phosphoric acid to weaken the glass matrix, followed by attrition scrubbing. Rutile fractions analyzed as high as 94 percent titania content. In several instances, more than 90 percent of the titanium in the shag was recovered to yield combined rutile fractions containing 90.2 to 92.6 percent titania.

Jan 1, 1971

By C. B. Daellenbach

A prototype particulate size analyzer system was developed that would rapidly determine size distributions of homogeneous and two-mineral materials in the 74-micrometer (200-mesh) to 7-micrometer size range. The system sizes particles in a series of hydrocyclone elutriation steps and senses the weight of the five sized fractions by nuclear attenuation techniques. Size distribution of materials was determined from experimentally developed mathematical relationships that existed between particulate weight and the measured transmittance of gamma rays from an Americium-241 source. In the developmental phases, size distributions of three minerals (quartz, magnetite, and hematite) and a laboratory prepared two-mineral mixture of quartz and magnetite were accurately determined by the prototype system. In later stages of the investigation, semiconcentrates, an intermediate magnetic product from a taconite plant, were evaluated. Using 25-gram feed samples of this industrial material, the analyzer system was found to predict weight percentages for individual size fractions with an accuracy of ±0.85 percent or better at a 95-percent confidence level.

Jan 1, 1974

By A. F. Colombo, R. T. Sorensen, D. W. Frommer

The Bureau of Mines developed a flotation method for concentrating spiral tailing produced from pilot plant tests on the Champion mine ore fines . The feed material contained about 49 percent Fe and 15 percent SiO2 and was posed mostly of specular hematite , muscovite , and chlorite . Bench- scale , batch flotation research developed a reagent suite composed of tall oil - fatty acid , fuel oil , sulfuric acid , sodium fluoride , and sodium silicate for recovery of iron minerals in the froth product . Concentrate made with the reagent suite contained 87.3 percent of the iron and analyzed 65.6 percent Fe and 1.9 percent SiO2 . Continuous flotation tests were made with a nominal feed rate of 400 lb /hr , but without middling recirculation . Using nearly the same amount and complement of reagents as in the batch tests , three similar continuous tests gave concentrates averaging 63.9 percent Fe and 3.1 percent Sio while recovering about 86 percent of the iron .

Jan 1, 1964

By Eugene Frey

"INTRODUCTION The Blue Bell fluorite deposits were examined in August and November 1944 by an engineer 3/ of the Bureau of Mines, and an underground project was set up. The Bureau of Mines began development of fluorite here February 10, 1945, and completed its survey on June 21, 1946.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepared the final report. The Metallurgical Branch, C. C. Ralston, chief, analyzes samples and perform beneficiaticn tests. The exploratory project was under the direction of Paul T. Allsman, chief, Salt Lake City Division, Mining Branch. Acknow¬ledgment is due R. Thurston of the Federal Geological Survey for mapping the topography of the area, and to F. H. Gunnell and W. A. Young of the divisional office for detailed mapping of the surface and underground development and interpretation of the results.The chemical analyses included in this report was performed under the direction of H. E. Peterson, analytical chemist; the petrographic studies on the ore were written by LaMar Evans, petrographer; and the beneficiaticn section was written by C. H. Schack, metallurgist, under the direction of S. R. Zimmerley, chief, Salt Lake City Division, Metallurgical Branch."

Jul 1, 1947

By Richard A. Dick

Eight blasts were fired in a 2-1/2-ft bench in the Stewartville member of the Galena Limestone formation in an aggregate quarry near Stewartville, Minn. The shots were dimensionally proportional to production-size bench blasts and were about 5 to 10 percent of full scale. The effects of site, timing of initiation, and burden-to-spacing ratio were studied in a 2 x 2 x 2 factorial experiment, using three boreholes, caw;, containing a 1/2-in charge diameter of high-density ammonia dynamite, in each blast. Detonation velocity measurements indicated that the dynamite detonated satisfactorily in the 1/2-in charge diameter. The effects of the three experimental variables were analyzed by weight for the percentage of oversized material produced and for size distributions determined by screening the entire muckpiles. The bench faces were painted before each shot in an effort to determine the origin of the oversized material. The square pattern (burden and spacing = 15 in) produced finer overall fragmentation and less oversized material than the rectangular pattern (burden = 15 in; spacing = 22-1/2 in). Sites 1 and 2 were about ft apart. Although site 2 produced slightly better overall fragmentation than site 1, the amounts of oversized material produced showed no significant difference. The timing of initiation (instantaneous or delayed) did not significantly influence the overall fragmentation or the amount of oversized material produced.

Jan 1, 1973

By W. J. Fullerton

This paper is one of a series being prepared by the U. S. Bureau of Mines describing mining and milling methods and costs at cement-plant quarries throughout the United States, end deals directly with methods and costs at the quarry and mill of the North American Cement Corporation at Catskill, N. Y. The process of manufacturing cement is described only as far as the final grinding of the raw materials. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in many instances cause embarrassment to individual producers, as well as to the industry as a Whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding; of the scone of the cost tabulations may ensue.

Jan 1, 1931

By P. J. Coleman

Research in the field of mining safety and health in the United States plays an important part in protecting the lives of miners. The National Institute for Occupational Safety and Health (NIOSH) Mining Program conducts surveillance, studies and developmental work aimed at improving the safety and health of miners. With recent reviews of the Mining Program by the National Academy of Sciences and the Mining Program response (NIOSH, 2008), the importance of setting goals, conducting high quality engineering and scientific research and evaluating the outputs, outcomes, relevance and impacts of these projects has been reemphasized. Surveillance of reported injuries is a first step in deciding on research directions and in designing specific projects. Groups of injuries often share features and attributes that suggest common causes and may respond to similar preventive efforts. Identifying groups of injuries also serves to prioritize intervention efforts. The Mine Safety and Health Administration (MSHA) Accident and Injury database (MSHA, 2008) provides individual case reports of mining injuries, illnesses and certain no-injury accidents (events such as roof falls that stop mine production or miners? activities for more than one hour). This database is an indispensable resource for researchers and stakeholders needing information on the statistics of these events. From an epidemiological perspective, research projects target groups of miners at risk due to specific patterns of work, equipment, mine settings and the management of safety and health in their mines. Incidence rates are provided by the MSHA data for selected variables, such as surface/underground location, standard industrial classification and state. While incidence rates are the preferred measure for all variables, denominators are not typically available; for example, to more clearly under-stand the data about injury by occupational type, it would be necessary to conduct demographic surveys. A current survey of the demographics of the mining industry should be complete by 2010, which will allow incidence rates to be developed for a number of variables such as age, occupation and experience. This survey will provide the first update of its kind since the first survey was conducted in 1985.

Jan 1, 2010

By Arden D. Fugate

This work was conducted to determine a feasible process for converting siliceous fluoride offgases to a commercially usable product. The offgases were generated by pyrohydrolytic defluorination of low-grade fluorspar in a gas-fired rotary kiln, and fluorine was collected as a hydrofluoric-fluosilicic acid. A silicon-free fluoride solution for further processing was then produced by neutralizing the acidic scrubber solution with anhydrous ammonia, silicon being separated as orthosilicic acid. Ninety to ninety-nine percent of the fluorine originally present remained in solution as ammonium fluoride. Silicon was also separated from synthetic fluosilicic acids, having F-to-Si weight ratios ranging from 3.50 to 14.3. The solutions below a ratio of 4.06, the F-to-Si ratio of H2SiF6, containing dissolved silicon were desiliconized as completely as those containing less than the stoichiometric quantity of silicon. An electrolytic-grade cryolite was recovered from the ammonium fluoride solution by reacting with either sodium aluminate or alumina trihydrate and sodium hydroxide. A product containing 97 to 100 percent of the fluorine, represented by Na3A1F6, was recovered, and 94 to 99 percent of the theoretical yield was realized.

Jan 1, 1963

By J. S. McNabb

"A search for manganese ore by core-drill exploration was carried out by the Bureau of Mines in the Philipsburg mining district in Granite County, Mont., in 1939 and 1940. This work was based on detailed studies of the manganese ore bodies of the district previously made by the Geological Survey.In 1949 further search for manganese in the district was deemed advisable. Diamond drilling was begun the following year as a joint program by the Geological Survey and the Bureau of Mines with the primary purposes of probing ore-leasing structures and extending the limits of known ore bodies. A secondary objective was to test a geologic theory based on a new conception of manganese-ore localization. The exploration targets were designated and the drilling results interpreted by the Geological Survey, and the Bureau of Mines was responsible for the drilling, sampling, and core handling. Improved drilling equipment and methods were utilized in an effort to obtain better core recoveries than resulted from the earlier drilling campaign.The Philipsburg mining district, Granite County, Mont., is 27 miles south of Drurrnnond, about 45 miles airline northwest of Butte, and 1 mile east of Philipsburg. During the course of the investigation patented lode-mining claims owned by the American Machine & Metals, Inc., the Contact Mines, Inc., and the Moorlight Mining Co. were diamond drilled.The district has been an important source of domestic manganese dioxide ore since local recognition of the mineral's importance during World War I. Peak annual output in 1918 of about 127,000 tons of manganese ore was utilized principally by the steel industry. A small but relatively steady output has persisted to the present to satisfy demands by battery manufacturers for battery-grade manganese dioxide.The known manganese deposits of the district are in sedimentary rocks of Paleozoic age. These rocks lie along a north-trending anticline traversed by a series of east-west tension veins. The east flank of the anticline terminates at a steep-dipping fault contact against a small granodiorite batholith.Replacement deposits of manganese oxides and carbonates occur locally in or closely associated with tension veins cutting calcareous rocks, or adjacent to the intrusive. Rhodochrosite has been a common accessory mineral in deposits valuable chiefly for lead, zinc, and silver. Some of the replacement deposits characteristically are irr2gular in outline, whereas others have fairly regular walls marking the limits of favorable beds."

Dec 1, 1955

By J. C. Franklin

The Spokane Mining Research Center of the Federal Bureau of Mines is placing major emphasis on chemical stabilization as part of the ground support program. Development of polymeric material suitable for bonding rock fractures around the mine opening is one phase of the program. Some of the problems that must be considered are viscosity, applicability, adhesion, cure times, strength, toxicity, and flammability. Epoxies and polyesters were investigated, but shrinkage in polyesters caused redirected effort toward epoxies. Test results with the latter showed that bonded fractures in mine-roof strata were stronger than the virgin rock. Further tests showed that polymeric materials have good potential for bonding, and in conjunction with polymer roof bolts, are expected to result in an economic and useful new support concept.

Jan 1, 1974

By J. E. Tiffany

A stick of explosive is a package of stored energy that can be released when needed to blast rocks, coal, and other materials; but, unlike fuels such as coal and gasoline, its potential energy is self-contained, there being enough oxygen within the package to complete the almost instantaneous reaction. When an explosive is ignited or detonated, the solid or liquid materials of which it is composed are converted rapidly into highly heated gases, which, if free to expand, would have a volume many times larger than that of the original explosive. At the instant of explosion these gases occupy only the volume of the shot hole and are therefore produced at a very high pressure, which causes the material that is being blasted to be broken or disrupted. In blasting coal efficiently the proper placement of the shot hole and the confinement of the explosive therein are both of prime importance. When these are not adjusted properly, only a small amount of the energy is expended in bringing down coal, consequently the balance of the energy tends to be expended by the emission of a flame into the working place that may lead to a gas or dust explosion. Permissible Explosives Defined The term "permissible explosive", as applied by the Bureau of Mines to explosives it has approved for use in blasting in coal mines, embraces not only the requirement that the explosive, when used, shall be similar in all respects to the basic sample that passed all the tests necessary for its admission to the published permissible list, but also that the explosive shall be used under certain prescribed requirements.

Jan 1, 1938

By Lloyd A. Morley

This annual report details progress under USBM Grant G0155003 during the project period of January 1, 1977 through December 31, 1977. The report contains four principal chapters covering accomplishments in the mine electrical safety research areas of continuous monitoring, battery and battery-charging safety, and computer modeling. Highlights of the work are summarized in the last report chapter.

Jan 1, 1978

By Robert W. Ageton

Optimal planning for mining the deep, lead-zinc-silver deposits of the Coeur d'Alene mining district, Shoshone County, Idaho, could be facilitated by a knowledge of the magnitude and direction of the pressure acting in the virgin rock. The distribution of primary stresses should be considered in order to prevent possibly destructive mining-induced stress concentrations. This particular investigation was concerned with determining stress in a zone 4,000 feet below the surface and known to be ender stress concentrations due to mining operations. Disking of the stress-relief cores obtained in a vertical down hole permitted qualitative evaluation from visual observations; the results indicate that a high lateral stress existed at the time the measurements were made. Stress-ellipsoid determinations gave a compressive principal stress of -13,000 psi oriented about N 45° W and nearly horizontal, a compressive principal stress of -11,000 psi oriented about S 45° W and abut 60° off the vertical pointing away from the vein, and a compressive principal stress -5 -7,000 psi oriented N 45° E and about 60° off the vertical, pointing toward the vein. Subsequent to the overcoring stress-relief drilling, a rock burst occurred about 100 feet northwest of the test site.

Jan 1, 1967