Search Documents

By Harold E. Marr

Energy dispersion X-ray analysis was evaluated for possible application in the secondary metals industries for the rapid analysis and identification of copper-base alloys. Laboratory investigations of standard brass and bronze samples indicate that X-ray methods are capable of separating standard alloys into 10 general classes with analytical times of less than 3 seconds per sample for clean, flat samples. A radioactive source of americium 241 with a secondary fluorescer was used as an excitation source, and a lithium-drifted silicon semiconductor detector was utilized for energy discrimination of X-rays.

Jan 1, 1974

By F. M. Goodwin, John Campbell, G. W. Jones

"INTRODUCTION In previous reports 5 results were given of a manhole investigation carried out over a period from June 1929 to July 193C in cooperation with the Edison Electric Illuminating Co. of Boston. Mass., and during 1931 in cooperation with the Edison Electric Illuminating Co. of Boston and the Boston Consolidated Gas Co., to determine the general hazards of combustible gases and vapors in manholes and other underground openings owned by the Edison Electric Illuminating Co. and to develop methods of eliminating these hazards. These investigations have demonstrated that the detection, control, and elimination of combustible hazards in manholes can best be obtained by a close cooperation of the interested parties through a systematic and continuous inspection of manholes, under proper supervision.The investigation carried out during 1932 has been along lines similar to those conducted during 1929, 1930, and 1931 test crew consisting of two men, one an employee of the Consolidated Gas Co. and the other an employee of the Edison Electric Illuminating Co., was continuously employed during the year in the testing of gases in manholes served by the Edison system. The test crew was under the direct supervision of John Campbell, superintendent of the special service department of the Edison Electric Illuminating Co., and F. M. Goodwin, vice president of the Consolidated Gas Co.As in the previous investigations, all tests were numbered. The test-data sheets, on which the information regarding the tests was recorded, were prepared in triplicate, ono copy going to the Edison Co., one to the gas company, and the third to the Bureau of Mines at Pittsburgh, Pa. These test-data sheets were then filed (1) according to the town, (2) the street location, and (3) the manhole number; in this way a complete record of each manhole tested was immediately available. A typical test-data sheet was given in the 1931 report. These data sheets were found to entirely satisfactory and no changes were made during the 1932 investigation. The procedure of sampling manhole atmospheres, shipment of the samples to Pittsburgh, and method of analysis has been the same as that described in the 1931 report and need not be repeated here. Likewise, there has been no change in the method of calculation of explosibility of the samples analyzed or the use of charcoal filter tests given in appendix A."

Jun 1, 1933

By Douglas F. Scott

Researchers from the U.S. Bureau of Mines conducted geologic investigations in an area of the Lucky Friday Mine, Mullan, ID, that included the 5300-107 demonstration stope using underhand longwall cut-and-fill mining. Structural analysis of the area suggested that argillite beds form planes of weakness between blocks of brittle quartzite, and energy may be released along these planes and at the junctures of fractures. Mapping argillite beds and fractures in the stope wall rock showed that the planes of these features diverged and that their attitudes corresponded from one wall to the other. Seismic analysis showed that the number and location of events varied as each cut was mined, with about 39 pct of the total number of events occurring above the cut being mined, about 54 pct below, and 7 pct at the same elevation.

Jan 1, 2010

By Harry R. Nicholls

A simple economical method has been developed for determining the in situ longitudinal and shear velocities in rock from which its elastic constants can be calculated. By detonating small charges of high explosives in shallow drill holes near a free surface, both longitudinal and shear waves were generated simultaneously. Accelerometers and velocity gages mounted to the rock surface were used to record the arrival time for both waves over travel path lengths from 50 to 450 feet, Measurements were made in two rock types. From the arrival time measurements, the longitudinal and shear wave velocities were calculated. From these velocities and the density of the rock, the elastic constants were calculated. The dynamic elastic constants of drill core samples of the two rock types were determined in the laboratory by the resonant-frequency method, The lab- oratory and in situ elastic constants are compared and significant differences noted. In general, there is less spread in the in situ data than in the laboratory data, and Poisson's ratio does not fall outside the theoretical limits for the in situ data as is often the case for laboratory-determined elastic constants.

Jan 1, 1961

By F. S. Crawford

During the course of a study of the safety organizations of the various iron mining companies in the Lake Superior district considerable in¬ formation regarding the methods of safety inspection in use was obtained which may be of value to other companies beginning safety work or contemplat¬ ing changes in their methods. A short description of the safety-inspection methods of eleven of these companies is given in this paper, and in the appendix are illustrated a number of forms used for safety inspections by several of the companies. Most of the companies whose methods are described use few forms for formal inspection. The one long form (10) attached which is used for a general in¬ spection by the safety inspector appears to present a good method for enabling the inspector to check all branches of his inspection and to assure himself that everything has been covered. All names of companies have been deleted from this paper and from the forms because the object is to disseminate information of constructive value rather than to point out the methods of particular companies by name.

Aug 1, 1931

By Kenneth J. Miller

The Federal Bureau of Mines coal-pyrite flotation process has been modi¬fied to produce a concentrated final clean coal slurry underflow that could be dewatered more effectively by filtration or centrifugation. This change was accomplished by redesigning the Bureau's two-stage flotation pilot plant facility and running the second-stage flotation step with undiluted or only partially diluted first stage coal froth concentrate. Results of the pilot plant flotation tests showed that substantial sulfur reduction could be achieved by flotation with undiluted pulp but some dilution is recommended for maximum selectivity. For example, coal-pyrite flotation in slurry of 25 percent solids yielded clean coal products analyzing as low as 0.7 percent pyritic sulfur and froth reject products containing slightly over 3.0 percent pyritic sulfur. In comparison, coal-pyrite flotation with pulp diluted to about 12.5 percent solids yielded clean coal containing as low as 0.4 percent pyritic sulfur and froth reject of 5.6 to 6.7 percent pyritic sulfur. Despite the need for some dilution, it was concluded that excellent coal-¬pyrite flotation selectivity could be achieved without diluting to 6 or 7 per¬cent solids as done in the earlier work. Thus the economics of coal-pyrite flotation would be improved by easing clean coal dewatering problems and by reducing second-stage flotation cell volume requirements.

Jan 1, 1977

By Fred Kissell

The Bureau of Mines has developed the shearer-clearer--a new type of dust control system for longwall shearers. The system partitions the airflow around the shearer into a clean split and a contaminated split. The dust cloud is confined to the vicinity of the coal face, while the shearer operators remain in the clean split on the gob side of the machine. The shearer-clearer operates on the principle that each water spray moves air like a small fan and can be positioned to direct the dusty air towards the face. The hardware is inexpensive and can be installed in a single shift. It consists of several strategically mounted water sprays and one or more passive barriers. Laboratory testing indicates reductions 1n shearer operator dust exposure as high as 97 pct. Preliminary results from an underground demonstration in one mine also indicate that considerable dust reductions at the shearer may be obtained. In conjunction with the development of the shearer-clearer, dust surveys were conducted in three other mines to determine if some shearer spray systems currently in use partition the flow in a manner similar to the shearer-clearer, and if so, whether this partially accounts for markedly cleaner conditions on some longwalls. Results from these surveys indicate this to be the case. A feature of the cleaner longwalls was a downwind orientation of their water sprays, which is a key element of the shearer-clearer system. The shearer-clearer system described in this report was designed for an Eickhoff EDW 300 shearer working a 7-foot coal seam. The testing to date has concentrated on cutting directions counter to the primary airflow. The development effort continues for different mining equipment and conditions. It is expected that different systems will be required to accommodate the range of conditions occurring underground. Application of the system presented here to conditions different than those described is not likely to produce the same results.

Jan 1, 1981

By M. L. Glenn

The Bureau of Mines is conducting research on Fe-based alloys using Si and Al additions to reduce the Cr required for heat-resisting appli-cations. Part of this research is being done to evaluate alloys containing (8-10)Cr-(10-14)Ni-(0-8.5)Si-(0-4) Al to determine which of these alloys have austenitic structures, as well as fabrication properties and oxidation resistance sufficient to substitute for type 304 stainless steel. Based on initial results, an Fe-lOCr-11Ni-5Si alloy and an Fe-8Cr-13Ni-5Si alloy were selected for evaluation of oxidati.on, stress rupture, and tensile properties. Both alloys have oxidation resistance at 7000 and 8000 C that is better than that of type 304 stainless steel. The stress rupture strengths are less than that of type 304 stainless steel but significantly better than that of commercial heat-resisting steels with similar Cr contents. Yield strengths of the alloys were equivalent to that of type 304. Both alloys had high tensile strengths comparable to those of stainless steels that transform to martensite during straining (e.g., type 301). These alloys have weld-hot-cracking resistance comparable to that of type 304 stainless steel. This initial study shows that Si has potential as a substitute for Cr in stainless steels for heat-resisting applications.

Jan 1, 1984

By E. R. Palowitch, A. W. Deurbrouck

The Bureau of Mines reviewed available data on the effect of crushing high - sulfur coals for the liberation of impurities in the light of increasingly stringent air pollution regulations . The survey , which provided information on Appalachian region coals only , indicated that such important coalbeds as the Upper and Lower Freeport and the Upper Kittanning show significant sulfur reductions when crushed to 14 - mesh top size . For many other coalbeds amenability to sulfur liberation by crushing was indicated , although too few samples were available to draw firm conclusions .

Jan 1, 1966

By K. E. Tame

An alkaline leaching procedure for recovering uranium from a submarginal 0.1 percent Ug Og calcareous carnotite ore from the Shiprock , N. Mex . , area was investigated . A recovery of 72 percent of the uranium was attained in a preliminary test embodying the commonly accepted practice of ( 1 ) alkaline leaching at 90° C , ( 2 ) multiple stage filtration and washing for recovery of a clear pregnant solution , and ( 3 ) caustic precipitation of uranium as sodium diuranate , with recycle of the barren solution to the leaching and washing circuits . Ion exchange resins were used in a second , less orthodox test that comprised ( 1 ) sodium carbonate leaching of minus 10- mesh ore at 90 ° C to dissolve the uranium , ( 2 ) filtration to recover the leaching reagent for reuse , (3 ) recovery of the uranium- bearing solution in the filter cake as a pregnant slime slurry by repulping of the filter cake followed by a sand- slime separation and countercurrent decantation (CCD ) washing for rejection of the sand fraction , (4 ) recovery of the dissolved uranium from the pregnant slime slurry by resin- in- pulp (RIP ) , ( 5 ) elution of the uranium from the resin with a solution of ammonium chloride acidified with hydrochloric acid , and (6 ) precipitation of the uranium with ammonia gas . About 83 percent of the uranium was extracted from the ore and 95.5 percent of the dissolved uranium recovered by ion exchange . Improved laboratory results were obtained using the RIP process , but larger scale tests would be necessary for economic evaluation of the two processes .

Jan 1, 1964

By C. E. Julihn

In the fall of 1933 a new discovery of gold was made in the old Mojave mining district of California about 70 miles north of Los Angeles. It led to mining operations that have surpassed in their results all reasonable expectations and are of exceptional promise for the future. In less than 3 years, exploration has opened up a number of veins, from some of which a substantial amount of high-grade ore has been shipped, while a large tonnage of milling ore has been disclosed. Two mills, operating on ore averaging better than $12 a ton, will probably produce more than a million dollars worth of gold in 1936, and a considerable increase of their output in the following year is anticipated. While continuance of these operations for a number of years is already assured by ample reserves of ore, future discoveries of still other veins are reasonably possible, as occurrence of gold throughout the volcanic rocks of the district is widespread and the veins now being mined showed little to attract attention at the surface.

Jan 1, 1937

By D. Eugene Rannels, Sarah E. Dunsmore

"Dunsmore, Sarah E., and D. Eugene Rannels. Extracellular matrix biology in the lung. Am. J. Physiol. 270 (Lung Cell. Mol. Physiol. 14): L3-L27, 1996.-The lung and other organs are comprised of both cellular and extracellular compartments. Interaction of these components modulates physiological function at the organ, cellular, and subcellular levels. Extracellular components in the gas-exchange region of the lung include both noncellular interstitium and basement membranes. Connective tissue elements of the interstitium in part determine ventilatory function by contributions to tissue compliance and to resistance of the diffusion barrier. The basement membrane underlies cells of both the alveolar epithelium and the capillary endothelium; basement membrane components exert biological effects on adjacent cells through receptormediated interactions. This review emphasizes current knowledge concerning the composition and biological activity of extracellular matrix in the alveolar region of the lung. Matrix synthesis and turnover are also considered. Directions for future research are suggested in the context of current knowledge of the lung and other model systems. EXTRACELLULAR MATRIXEXTRACELLULAR MATRIX is a general term that encompasses components of the basement membrane and interstitial connective tissue. The extracellular matrix has many functions. It provides structural support, compartmentalizes tissues by separating epithelium or endothelium from interstitium, and serves as a physical barrier. Both in vivo and in vitro studies show that extracellular matrices also affect cell shape and function. The matrix elicits a variety of cellular responses, including adhesion and spreading, changes in cytoskeletal organization and differentiation, formation of focal contacts and stress fibers, stimulation of proliferation and migration, induction of polarity and gene expression, alterations in metastatic activity, and outgrowth of cell processes (for review see Refs. 387, 462). Cellmatrix interactions play roles in embryonic development and organogenesis (for review see Refs. 1, 91), in wound healing (for review see Refs. 145, 327), iri metastasis (for review see Refs. 430, 431), and in angiogenesis (for review see Refs. 185, 186). The extracellular matrix is the subject of a large volume of literature. In 1994, over 1,000 articles contained extracellular matrix in the title or abstract. After a brief discussion of key aspects of extracellular matrix biology, this review will focus on the extracellular matrix of the lung."

Jan 1, 1998

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

MINE VENTILATION NETWORK ANALYSIS

Jan 1, 1977

By S. M. Shelton

The widespread occurrence of domestic manganese deposits and the shortage of ferromanganese-grade ore have been sources of much speculation and investigative effort for many years. The present emergency has intensified the search by the Bureau of Mines for methods of producing ferromanganese-grade concentrates4/ from low-grade ores.

Jan 1, 1941

By S. M. Shelton

[The widespread occurrence of domestic manganese deposits and the shortage of ferromanganese-grade ore have been sources of much speculation and investigative effort for many years. The present emergency has intensified the search by the Bureau of Mines for methods of producing ferromanganese-grade concentrates4/ from low-grade ores.]

Jan 1, 1941

By E. L. Litchfield

Descriptions are given of the techniques and apparatus used by the Bureau of Mines for determinations of flat plate ignition quenching distance and minimum spark ignition energy. The descriptions include discussions of reaction vessel materials, shapes, and sizes and discussions of electrode configurations. Spherical, hemispherical, or flat plate electrodes are recommended. The preferred metal in electrodes and electrode supports is stainless steel; the flat plate electrodes incorporate flanges of low electrical conductivity which are most frequently formed from glass. Various aspects of the electrical energy supply system are discussed and suitable arrangements of components are indicated. The concept of a thermal relaxation time is introduced as a basis for the choice of a minimum interspark time during the testing of a gas mixture. The following indicate the varied conditions under which these tech were utilized: Mixture pressures between 10 mm Hg and 45 psig, initial temperatures between -78° and +198° C, and gaseous mixtures representing wide ranges of cL.. D reactivity and corrosiveness. Minimum ignition energies were determined which varied from about 10-7 joule to nearly 103 joule.

Jan 1, 1967

By Anthony T. Iannacchione

The Bureau of Mines developed data on the methane content of the Hartshorne coalbed, Haskell and Le Flore Counties, Okla. The methane content is calculated to be between 1.1 and 1.5 trillion cubic feet, based on an estimate of total coal in place of 2.4 to 3.2 billion short tons. Methane increases with depth, but the rate of increase decreases with greater depths. Degasification in advance of mining is recommended for all mines operating at depths greater than 500 feet to reduce hazards and methane explosions, decrease mine ventilation costs, and conserve the natural gas that would be otherwise wasted.

Jan 1, 1979

By T. J. Ballard

The Ore Knob mine, in Ashe County, N.C., was one of the largest producers of copper in the eastern states during the 1870's. The ore occurs in a fissure vein, which strikes N. 64° E. and dips nearly vertical. The country rock is granite gneiss. Drilling indicated that the vein structure is approximately 200 feet wide and 1,500 feet long. The vein material shows evidence of replacement of the original gneiss by sulfides. Solution cavities in the vein were noted in some places. The ore minerals and pyrrhotite, chalcopyrite, pyrite, and minor quantities of sphalerite. The gangue contains biotite, magnetite, albite, calcite, and many silicate minerals.

Jan 1, 1948

By Mah Alla D.

Previously existing heat-of-formation values for the oxides of vanadium were rudimentary. They were subject to uncertainties of 1 to 5 kilocalories per gram-atom of contained oxygen. This fact has been the only adverse influence on the accuracy of thermodynamic calculations involving these substances, as the requisite entropy and high-temperature heat-content data are known with reasonable accuracy. This report presents new heat-of-formation data for four oxides of vanadium (VO, V203, V02, and V205), obtained by combustion calorimetry. It is believed that the uncertainties have been reduced to 0.1 to 0.3 kilocalorie per gram-atom of contained oxygen. The new heat-of-formation data were combined with existing entropy and high-temperature heat-content values to obtain free energies of formation of the four oxides at temperatures up to 2,000° K.

Jan 1, 1961

By A. M. Gaudin

A study of the consumption of reagents used in flotation gives useful data as to the market which employment of the flotation process creates for the manufacturers of the necessary chemicals and oils, and furnishes a useful clue to the trends in flotation practice influencing the choice of reagents used and the' extent to which new reagents are displacing less suitable older reagents. In the present investigation an attempt has been made to cover both of these phases of the consumption of reagents in flotation. Unfortunately, however, the data collected in tie various districts have not been equally informative; some operators have reported very completely both the consumption of reagents and the metallurgical results obtained therewith, while others were apparently unable to supply these figures in sufficient detail to meet the requirements of this investigation. RESULTS OF INVESTIGATION Table 1 gives the tonnage of ore treated by flotation, as reported. This table shows that flotation has been most largely used in the concentration of copper ores, next in complex lead-zinc ores, followed by lead ores, zinc ores, miscellaneous ores, and copper-iron ores.

Jan 1, 1929