Search Documents

By K. Kar, A. Sreeoath, M. Gautam

"This paper presents results of an experimental investigation of the sampling efficiency of a blunt cylindrical sampler oriented with respect to the oncoming flow. The number of particles sampled by the cylindrical blunt sampler and an isokinetic sampler is measured using the TSI Aerodynamic Particle Sizer. A technique is described to conven the ratio of the particles sampled into the sampling efficiency. The experimental data thus obtained is then compared with the impaction model of Vincent and Mark (1982) with the empirical constant determined from our experiment.. The comparison shows excellent agreement for 0° and 90° orientation.1.0 IntroductionCylindrical dust samplers are widely used in practice to determine the concentration of the airborne particulate matter. The sampler is simply a means to collect particles from the ambient, whose concentration is subsequently measured by some size selective techniques. Gravimetric and optical techniques are the two most commonly used methods to measure the particle sizes. While impactors are used in gravimetric analysis, Aerodynamic Particle Sizer, Aerosizer. Electron microscope, Coulter Counter etc. use the optical method to measure the particle sizes. The Aerodynamic Particle Sizer (APS) and the Aerosizer are the new generation devices which employ the time of flight of particles within intersecting laser beams to determine the particle size.The introduction of the sampler in the free stream disturbs the flow pattern due to two distinct actions of the sampler on the fluid stream: one of them results due to the conformity of the flow to the geometry of the circular cylinder and the second one is caused by the flow into the suction orifice. If the sampler performance is determined by the number of particles entering into the sampler inlet relative to the number of particles present in the free stream, then the particle trajectory outside the sampler and into the inlet is the deterministic factor for the sampling efficiency. The particle trajectory inside the sampler is not important in this case."

Nov 1, 1995

By W. E. Dennis

"INTRODUCTION The strategic importance of zinc warranted investigation of the Silver Eagle zinc prospect, which was first examined by an engineer 3/ of the Bureau of Mines in January 1943.From October 12, 1943, to March 16, 1944, the Bureau explored the deposit by trenching, core drilling, and sampling to establish the amount and grade of ore and to test for the presence of sulfide-ore minerals at depth.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Oct 1, 1946

By J. G. Donaldson

Cobalt-tungsten binary deposits were formed in laboratory experiments by hydrogen reduction of the anhydrous mixed vapors of cobaltous chloride and tungsten hexachloride. The materials were sublimed in seperately heated zones of reaction tube and were transported in a stream of purified helium into the deposition section of the tube where the chloride gases were reduced to metal by a countercurrent flow of hydrogen. Heattreating of the near stoichiometric binary metallic deposits converted nearly all to the intermetallic compound Co3W, however, small quantities of both cobalt and tungsten remained. Mechanical tests showed that the tensile strength of heat-treated 75 percent cobalt-25 percent tungsten deposits was twice as high as that of similarly treated deposits of cobalt.

Jan 1, 1965

By Warren E. Morrison

Demand for energy in the United States in 1965 was stimulated by the continuing expansion of the economy. A gain of 5.9 percent in gross national product for the year was accompanied by a 4.4-percent rise in energy consumption. Domestic energy resources met about 93 percent of the nation's requirements. The remaining 7 percent consisted of imported fuels, mainly of crude petroleum and residual fuel oil. The major fossil fuels-natural gas, crude petroleum, and coal, in that order-contributed 96 percent of all commerical energy utilized, with the balance of 4 percent being primary electricity from hydropower and nuclear power plants. Production was up for all of the major mineral energy resources in 1965, with the single exception of anthracite, output of which continued to decline. Bituminous coal output for the year was 512 million tons; marketed production of natural gas, 16,039 billion cubic feet; and crude petroleum output, 2,848 million barrels. Among the secondary products processed from primary energy resources, the most significant gains were in coal carbonized for coke which increased 6.7 percent to 95 million tons, and in the output of liquefied gases from natural gas which rose 4.8 percent to 11,257 million gallons (268 million barrels). Within the latter category, the off? take for petrochemical feedstocks continued to rise at a very rapid pace.

Jan 1, 1967

By C. F. Davidson

The Bureau of Mines studied the extraction of lithium from lithium-containing clays by chlorination with hydrogen chloride (HC1). In bench-scale laboratory investigations, HC1-H20 mixtures were used to selectively chlorinate lithium, but not calcium or magnesium, in lithium-containing clays. The addition of calcium carbonate to the clay was found to improve the lithium recovery. Reaction conditions found to affect the lithium recovery were ratio of clay to carbonate, reaction temperature, and HC1 concentration. The best conditions for selective chlorination of the lithium were 2:1 clay-carbonate, 750° C, and 20 wt-pct HC1. The experimental results and trends in lithium extraction are explained using thermodynamic relationships.

Jan 1, 1981

By McHenry Mosier

This paper describes come mechanical raid electrical signal systems in common use in Metal-mine shafts, together with several distinctive systems that indicate or control the origin of the signal. The latter systems remove the hazard of the movement of the cage from one level in response to signals from another. Previous publications of the Bureau of Mines have covered several meritorious installations One of the best signal systems for deep shafts is at the Homestake mine4/. A successful installation of an induction system in the Lake Superior mining region permits signaling as well as telephoning from cages at rest or in motion5/. El Potosi mine uses a variation of the three-wire electric system6/. A mine in Utah has developed a system of the double trolly-wire type, in which the cage attendant may signal from a moving cage7/. At present no system of the sine-shaft signaling employing radio is available.

Jan 1, 1939

By N. N. Moebs

The atmosphere in part of an air-sealed coal mine was monitored continuously through a drill hole for oxygen content to determine the effectiveness of sealing a mine against the entrance of air and the major force that caused the phenomenon of mine breathing through the overburden. The differential pressure across the seal and the barometric pressure on the outside also were recorded. A general correlation, obtained between the oxygen level, differential pressure, and barometric pressure, indicates that changes in air pressure are the cause for periodic replenishment of the oxygen in the mine. Mine effluent quality was determined by conditions in many sections of the mine and could not be related to the oxygen level at the drill hole.

Jan 1, 1972

By Jr. Kauffman

The data contained in this report were obtained incidental to the Bureau of Mine's investigation of the lime-soda sinter process as applied to the recovery of alumina from siliceous bauxite, kaolin, and other high aluminous materials. The Bureau of Mines was charged by Congress to investigate processes for the production of aluminum from domestic low-grade ores. The Eastern Experiment Station at College Park, Md., conducted laboratory and pilot-plant investigations of the recover-y of alumina by the lime-soda sinter process. Reports by the College Park staff covering the recovery of alumina from these sources have been published. The lime-soda sinter process involves the sintering of the finely ground siliceous bauxite or clay with limestone and soda ash in a rotary kiln. During the sintering the alumina supposedly reacts with the soda ash to form soluble sodium aluminate and the silica combines with the lime to form the insoluble orthosilicate. In the early stages of the investigation it was considered desirable to know the temperatures at which the phase changes occurred during the sintering operation. The total time involved in the passage of any given portion of the charge through the kiln was 28 minutes. The exposure time of the charge to temperatures above 600° C. (decomposition temperature of kaolinite) was, roughly, half the total. The exposure to the full temperature of the kiln, 1,100° C was only 3 minutes. (Subsequently, the maximum kiln temperature and retention time were increased.)

Jan 1, 1949

By Ivan F. Avery

The design productive capacity of natural-gasoline and cycling plants in the United States on January 1, 1960, was 54.6 million gallons per day, according to the Bureau of Mines biennial survey. This represents an increase of 5.8 million gallons per day during the 2-year period since the last survey. The major increases occurred in Louisiana, Oklahoma, New Mexico and Texas. In Utah, natural gasoline capacity was reported for the first tine at 320 thousand gallons per day as of January 1, 1960. The total number of plants increased from 584 on January 1, 1958, to 596 on January 1, 1960. However, the operating plants decreased from 558 to 555 in the same period.

Jan 1, 1961

By A. W. Deurbrouck

This report describes the preparation characteristics of the significant coalbeds from which samples could be obtained in Webster County, W. Va. In 1964, approximately 825,000 tons of coal was produced in the county, of which 732,000 tons was mechanically cleaned in three preparation plants. The Sewell coal bed accounted for 94 percent of the coal produced. Twelve samples were collected from five coalbeds. Four of the samples would require upgrading to meet metallurgical requirements; two others of just over 8.0 percent ash would require some upgrading. In general the coalbed samples collected in the county were of medium-sulfur and medium-to low-ash content as received or after removal of the sink 1.58-specific-gravity material.

Jan 1, 1966

By J. M. Mutmansky, L. Xu

"This paper outlines the results obtained when sampling twenty underground coal mine sections, each in a different mine. The sampling effort was oriented toward a detailed characterization of coal mine dusts and thus eight-stage Anderson Model 298 impactors were used as the primary collection instrument. This instrument allowed a rather detailed size distribution for each of the particulates sampled. Because four of the mines used diesel outby equipment and/or diesel shuttle cars at the face, it is possible to make some comparisons on the particulate distributions in diesel versus non-diesel mines.One of the more interesting results is the pattern that exists in mines that contain only diesels used for outby utility haulage. Particulate in these mines seem to be consistently heavy in the fine size ranges, perhaps being of significant concern to the industry. While no definite conclusions can be achieved from the limited data collected in this study, the data indicates that more detaile~ study of particulates in diesel mines is needed so that some idea of the particulate loadings in diesel mines can be achieved."

Jan 1, 1988

By H. Foster Bain

Ten years ago there was no general , country-wide service for the systematic training of miners in matters relating to safety . A beginning only had been made at a few scattered points . Under the old conditions each man was left largely to look out for himself in meeting the hazards of his day's work, and the foreman , shift bosses , and superintendents chiefly relied upon improvision when major accidents occurred . So long as the mines were small and the workers highly intelligent and well trained in routine mining methods , and when too , the pressure for output had not yet speeded up industry to the extent it has since those days , there was something to be said for this lais- sez faire attitude . When , however , the rapid expansion of industry lead to the introduction of new and little trained labor and to units of production of greatly increased size , the natural dangers of mining were greatly intensified . An accident in a small mine affects only a few; the same accident in a large mine , unless proper precautions have been taken , may cost the lives of many . The public does not generally recognize that the greatly increased outputs of the mines , of coal mines in particular , have been in recent years , obtained from substantially the same number of miners as ten years ago but with a personnel not nearly so well trained in mining . It is inevitable under : such conditions that more care must be devoted to avoiding accidents and much more elaborate preparations made for meeting them . In the years immediately preceding the establishment of the Bureau of Mines this speeding up of industry , change in the character of mine labor , and increasing hazard had all begun to be felt . Immediately prior to the organization of the Bureau of Mines , public attention had been drawn to a series of disastrous coal-mine explosions , to the increasing frequency of these disasters , and to the terrible loss of human life . resulting therefrom. One of the first problems , therefore ; confronting the Bureau was clearly that of finding methods of reducing the number of such disasters and lessening the severity of those that continued to occur . Toward this object were immediately directed the energies not only of the Bureau of Mines but also those of State mine inspectors , mine operators and various other agencies , all of whom were urged to cooperate in this great humanitarian work. The results of this work naturally cannot be measured by figures only . Work for increasing the health , safety , comfort , and happiness of human beings may not be gaged with mathematical precision . But certain features of this work as revealed by the record from year to year are of much interest . ”

Apr 1, 1921

By William M. Nabors

As a part of a program to promote conservation and efficient utilization of petroleum resources, Bureau of Mines engineers are studying secondary oil-recovery projects in the United States. Published reports that set forth the pertinent facts of these operations help others to profit by the experience gained. This report presents the results of a study of secondary-recovery methods used in Kentucky by the Cumberland Petroleum Co. on its L. C. Bailey lease, Oil Springs pool, Magoffin County, Ky. This is believed to be the first water-flooding project in eastern Kentucky (fig. 1).

Jan 1, 1958

By Ronald D. Hill, Elmore C. Grim

Sediment is one of America's greatest pollutants. More than a billion tons of sediment reach the major streams of the United States annually(l). Damages are reflected in the reduced carrying capacity of streams, clogged reservoirs, destroyed habitat for fish and other aquatic life, filled navigation channels, increased flood crests, degraded facilities for water-based recreation, increased industrial and domestic water treatment costs, premature aging of lakes by enrichment of the water with silt-carried fertilizer that promotes algae growth, destroy crops, and reduce productivity of flood plain soils. Erosion and sedimentation are natural processes that are usually gentle actions releasing controlled amounts of silt from watersheds to receiving streams. Surface mining activities accelerate these natural processes and short duration, high intensity storms can become a violent force moving thousands of tons of soil in a brief period of time. Cover is a very important factor. With the removal of ground cover, water moves across the denuded area on its own terms picking up soil particles as it flows and leaving gullies behind. The susceptibility of strip-mined land to erosion depends on: 1.Physical characteristics of the overburden 2. Degree of slope 3. Length of slope 4. Climate 5. Amount and rate of rainfall 6. Type and percent of vegetative ground cover. By development of erosion and sedimentation control plans before disturbance of the area, many of the detrimental effects of strip mining can be prevented.

Jan 1, 1974

By Paul B. Harder

Round Mountain Gold (RMG) in cen­tral Nevada, reports that over a nine-year period and a million operating hours, its fleet of 150-ton and 190-ton haul trucks has averaged better than 93% availability, with some of the trucks approaching 70,000 operating hours. Repair costs have been far below industry averages. Mine operations manager Pete Kesl credits the high availability and low repair costs to a succession of Product Support Agreements between RMG and Caterpillar dealer Cashman Equipment. He adds that good equipment and a high level of trust and co­operation between all parties to these agreements have been essential to their success at Round Mountain.

Jan 1, 1998

By Kenneth L. Cashddollar, Terry G. Montgomery, Eric S. Weiss, John E. Going

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research on dust explosions by studying post-explosion dust samples. The samples were collected after full-scale explosions at the PRI, Lake Lynn Experimental Mine and after laboratory explosions in the PRL 20-L chamber and the Fike 1-m3 chamber. The dusts studied included both high and low volatile bituminous coals. Low temperature ashing for 24 hr at 515°C was used to measure the incombustible content of the dust before and after the explosions. The data showed that the post-explosion incombustible content was always as high as or higher than the initial incombustible content. The MSHA alcohol coking test -was used to determine the amount of coked dust in the post-explosion samples. The results showed that almost all coal dust that was suspended within the explosion flame produced significant amounts of coke. Measurements of floor dust concentrations after LLEM explosions were compared to the initial dust loadings to determine the transport distance of dust during an explosion. All of these data will be useful in future forensic investigations of accidental dust explosions in coal mines or elsewhere.

By John W. Buch

Safety and cost in mining coal beds under the extreme pressures found at depth, full extraction to conserve resources, and even surface subsidence to minimize damage of improved areas have directed much well-deserved attention, in the United Kingdom; to roof-control methods. Because the effects of pressure will be felt intensely as our Pennsylvania anthracite mines grow deeper, the senior author took advantage of an opportunity afforded by a mission to Europe3/ to observe, to a limited extent, the effects of pressures found in deep mines and the manner in which they are con trolled. Organized research relating to strata control has been carried on in Great Britain for nearly 25 years. These activities have been ably outlined by Dr. D. W. Phillips.4/ Physical properties of coal-measure rocks, movements of roof and floor, and types of face and roadway supports have been investigated. Same of the forces induced by the extraction of coal have been measured. The results of this research have been publicized and openly discussed, and much progress has been made in establishing a better factual understanding of roof-control problems and their solution.

Jan 1, 1951

By Uldis Jansons

This report evaluates the economic Mining feasibility of four selected mineral deposit types that can be anticipated to be found in (d)(2) lands in the western Brooks Range, Alaska. The major assumption made for this study is the availability of a rail system for transporting equipment and concentrates for the base metal mines. Commodity prices used are those in existence in July 1976. Mine models were established based on known deposits and then evaluated. A lead-zinc-silver-barite deposit for which grades were available but ore reserves were assumed would require approximately 25% higher ore grades or higher metal prices to yield a 15% discounted cash-flow rate of return an the investment if mined at a rate of 10,000 tons per day open pit methods. Large copper-zinc mineral deposits could be mined economically at rates either of 5,000 tons per day underground or 10,000 tons per day by open pit methods. A high-grade copper deposit require a copper price of over one dollar ryes pound to yield an economic profit to be mined at 2,000 tons per day by underground methods. A small high-grade gold underground mine would require a gold price of about $295 per ounce to yield a 20% discounted cash-flow rate of return on investment if all new mine equipment were used and if existing labor rates were paid: Enterprising mining groups operating as partnerships might be able to operate this mine profitably at a gold price of about $152 per ounce, perhaps slightly less.

Jan 1, 2012

By J. H. Field

Capital and operating costs have been estimated for removing sulfur dioxide from flue gases of a powerplant of 12,000-kw. capacity by liquid-purification processes, using limestone, ammonia, or sodium sulfite as the reactant. The annnonia and sodium sulfite processes yield end products that may be marketable. Coals containing about 1.5 and 5.0 percent sulfure have been considered. The sulfur dioxide content of the gases to be treated is 0.083 and 0.30 percent, respectively. Estimates have been made for 90-percent removal of the sulfur dioxide from both gases. A third instance has been considered in which 70 percent of the sulfur dioxide is removed from the flue gas of 0.30-percent concentration. The scrubbed gas would contain 0.09 percent sulfur dioxide, which might be within the permissible limit for discharge to the atmosphere in most areas. Although it is unlikely that flue gases with sulfur dioxide concentrations of less than 0.10 percent would require purification, a cost estimate for such a gas is included because an estimate is available for a British plant employing the limestone process at these conditions. Capital investment and operating costs, with no credit for products, are lowest for the limestone process for gases of both concentrations. Crediting the ammonium sulfate and sulfur produced in the ammonia process at their market prices at the end of 1956 of $32 and $28 per ton, respectively, the operating costs of the ammonia process become the lowest for purification of the gas containing 0.30 percent sulfur dioxide. The operating costs of the sodium sulfite process for purifying gas of high sulfur dioxide content approach those of the limestone process when the byproduct sulfur dioxide is credited at $14 per ton. Even if credit for products is allowed for the ammonia and sodium sulfite processes, the operating costs are higher than those of the limestone process for the gas of low sulfur dioxide content. Because of the large quantity of materials that would be produced by removing sulfur dioxide from a relatively small number of plants, credit for products should be allowed with extreme caution.

Jan 1, 1959

By R. P. Adams

Because of the extreme interest in materials with high melting temperatures and the advantages offered over the powder route for making high-density material, arc-melting and centrifugal-casting methods were investigated for preparing shapes of hafnium carbide with and without excess carbon. Highly satisfactory equipment was constructed and efficient operating procedures were established. Also, methods for preparing consumable electrodes and shrink-tolerant graphite molds were developed. Although crack-free hafnium carbide (6.3 weight-percent carbon) shapes were not made, coherent castings containing 9 to 13.5 weight-percent carbon were produced; the same compositions were shown to be resistant to thermal shock. Selected physical and chemical tests were performed on castings chosen for investigation by chemical and nondestructive inspection techniques. Electrical conductivity and thermal expansion measurements were made. Measurable oxidation of all the compositions studied was observed to start between 500° and 600° C. Attack by nitrogen, however, did not occur until temperatures exceeded 2,000° C. A linear relationship of the logarithm of the diamond pyramid hardness to the temperature was noted. Considerable scatter of the bend-rupture strengths at room temperature and of the tensile strengths up to 2,000° C was found. However, at the latter temperature and above, a definite relationship of strength to temperature was observed and some ductility was noted.

Jan 1, 1968