Search Documents

By Robert L. Rough

This report presents the results of an investigation by Federal Bureau of Mines engineers of water-injection projects in the northwestern Pennsylvania and southwestern New York area, where oil-producing wells have been converted from pumping to flowing. Data from 24 leases converted to flowing were collected and examined. Only 10 leases had information of significant scope for inclusion in the final analysis. The projects were classified in one of two categories. Group I consisted of leases operated to permit an evaluation of operational changes in terms of existing pressure differentials between injection and producing wells. Group II included remaining properties, for which enough information was available to justify an economic analysis but which did not have sufficient production data to support an engineering study because of radical changes in operational techniques. Variations in production and costs resulting from conversion to flowing were examined for production methods, well-spacing and completion techniques, and reservoir characteristics. Where water-injection rates were constant, oil production usually decreased rapidly at the time of conversion; production then increased slightly for 6 to 8 months before resuming a normal decline rate considerably below the estimated pumping rate. The abrupt decrease in production after conversion is indicative of lower pressure differentials between injection and producing wells, caused by the increased hydrostatic head in the producing wells.

Jan 1, 1960

By E. G. Davis

The flash reduction of fine iron ore in a dilute-phase system was investigated at 500° to 900° C within a heated stainless steel tubular coil. Alabama brown iron ore and Mesabi semitaconite ore were fed into the coil concurrently with reducing gases of hydrogen and reformed natural gas, so that the velocity of the gas at the reaction temperature was sufficient to entrain and pneumatically transport the solids through the coil. Reduction is very rapid with retention time of the ore in the coil varying from 4 to 15 seconds. Variables affecting reduction are temperature, ore feed rate, and gas flow or velocity. Results of the studies show that a partially reduced product (10-to 25-percent reduction) can be made which, on subsequent magnetic concentration, yields a concentrate containing 64 to 70 percent iron with a 90-to 94-percent iron recovery. Maximum reduction of 77 percent was obtained when hydrogen was used in a four-stage reduction test to yield a product containing 61 percent metallic iron.

Jan 1, 1972

By N. Kyriazi, W. Duerr, J. Shubilla, J. G. Kovac, J. Kravitz

A joint effort by the Bureau of Mines and the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, was undertaken to determine how well self-contained self-rescuers, deployed in accordance with Federal Regulations (30 CFK 75.1714), held up in the underground environment. This report presents findings regarding laboratory-tested breathing apparatus from the first year of a 5-yr program as well as other related findings. The SCSR's were tested on human subjects and on a breathing and metabolic simulator. These results indicate that the apparatus, if well-treated, perform as expected except for manufacturing defects or quality control problems, which are identified. However, when the apparatus are carried in and out of the mine every day and stored at the working section, they may suffer abuse that can be extreme. Physical signs of abuse, unless extremely obvious, frequently are not detected by the miners or the mine operators; this poses a danger to a potential user in case of emergency. Recommendations include improved training in inspection procedures.

Jan 1, 1986

To pinpoint dust sources and to improve dust control on longwalls. Approach Use short-term gravimetric sampling to determine the severity of various dust sources, and to evaluate dust control techniques used in longwall mining. Short-term gravimetric sampling can be used to isolate dust levels produced by various dust sources. How It Works Traditionally, gravimetric samples have been collected over an 8-hour shift, yielding time-weighted, average dust concentrations. This method gives a good indication of the full-shift respirable dust exposure of underground workers, but is less than satisfactory for identifying dust sources, determining their severity, or for evaluating the effectiveness of dust control techniques. Short-term gravimetric sampling uses equipment available to all mine operators. Two individuals composing the survey team each collect multiple (three to four) gravimetric samples during selected segments of the mining cycle. Multiple samples are necessary to insure accuracy, and to obtain a valid average measurement of the respirable dust concentration when sampling for short periods of time (typically 20 to 30 minutes). The gravimetric instruments may be carried in a sampling package or in a "sampling vest." A fishing vest with four large pockets can be used for this purpose. The sampling pumps are carried in pockets and the sampling head assemblies arc hung across the front of the vest.

Jan 1, 1982

By Robert L. Crosby

The Bureau of Mines investigated the substitution of cement copper powder for commercial copper powder in an Fe-7 pct Cu-l pct C powder metallurgy alloy. Copper powders from six different commercial cementation operations were separately upgraded by screening and hydrogen reduction. They were then mixed with commercial iron and graphite powders to form the Fe-7 pct Cu-l pct C alloy. Various chemical and physical properties were determined on the upgraded cement copper and the alloy powders. Mechanical, physical, and chemical properties were determined on green and sintered specimens made from the alloy powders. Mean tensile and bending strength of sintered specimens were significantly lower than the means from specimens made from commercial metal powders. The lower strengths are apparently related to poor sinterability.

Jan 1, 1970

By H. P. LeVan

Research was conducted to examine the feasibility of extracting manganese from Georgia umber ore by a three-stage continuous sulfuric acid-ferrous sulfate pickle liquor leaching process. A continuous cyclic process for treating the umber was operated successfully, using a synthetic solution simulating a ferrous sulfate fortified anolyte solution discharged from a manganese electrolytic cell as the leaching medium. Leaching efficiency based on removal of the manganese from the ore ranged from 83 to 89 percent for all systems tested.

Jan 1, 1965

By N. N. Moebs

The Bureau of Mines air-sealed a 77-acre) above-drainage coal mine to evaluate sealing as a means of reducing the acid and metallic salt contents in drainage from abandoned mines. An approximate reduction in acidity of 150 ppm (equivalent to 193 pounds per day) and in iron of 98 ppm were directly attributed to sealing. The topographical, hydrological, and other factors involved in air-sealing are discussed, and the construction used to seal the mine is described.

Jan 1, 1970

By W. R. Hardwick

This paper describes block -caving methods and practices of the Bagdad Copper Corp. in Yavapai County , Ariz . It is one of a series being prepared by the Federal Bureau of Mines on mining methods , practices , and costs in various mining districts of the United States . The story of the Bagdad caving operation is of particular interest because the ore body was not as thick as at other mines where the method had been successful . At Bagdad the caving method worked very well as a smallscale operation of 300 tons per day but was abandoned when production was increased to 2,000 tons per day . The Bagdad mine is in western Yavapai County , Ariz . , about 22 miles northwest of Hillside , a station on the Phoenix -Ash Fork branch of the Atchison , Topeka & Santa Fe Railway system ( fig . 1 ) . Copper ore now is mined by open -pit methods . The ore is concentrated , and the concentrates are trucked to Hillside and shipped by rail to a custom smelter . Some molybdenum sulfide is produced as a byproduct . This report gives a brief history of the district , describes the ore de- posit , and outlines the methods of prospecting , exploration , and estimation of ore . Development and former underground mining , including stope preparation , stoping , and transportation , are described . Extraction of ore , production rates , miscellaneous operations related to mining , wage and contract systems , and method of concentration are described . The final section discusses mining costs . The underground mine was visited by the author several times between 1937 and 1942 , and some information has been drawn from personal notes . The property again was visited in June 1957 , and maps and plans for this paper were furnished by the company at that time ; they have been edited to conform with Bureau of Mines format . The underground mine could not be visited then because it had been closed in 1948 when open -pit mining was begun .

Jan 1, 1959

During the 20th century, the increased emphasis on worker health and safety and the advent of new mining equipment and methods led to many changes in mine face ventilation practices. Efforts by government and private industry to improve and modify ventilation practices resulted in better health and safety conditions for workers. This article focuses on U.S. Bureau of Mines (USBM) and National Institute for Occupational Safety and Health (NIOSH) research to examine factors that had a significant influence on mine face ventilation design during the past century. Several "milestone" events are discussed along with the impact they had on worker health and safety. Significant ventilation research efforts by government and private industry are presented. This brief ventilation history highlights innovative face ventilation designs and a consistent commitment to mining health and safety. Ventilation has always been a concern in underground coal mining. For many yeas, there was no appreciation of how ventilation could be used to remove harmful contaminants from the air or how to control airflow quantities. The first known problems with ventilation date back to the 14th century, when it was recognized that lack of air was a major impediment to the expansion of mines. The common method of solving ventilation problems at that time was to abandon the existing mine and start a new one nearby. Ventilation in the early days of coal mining was accomplished by means of a natural draft, created principally by a difference in the weights of columns of air between the intake and return openings. Later, in the 18th and 19th centuries, a furnace was introduced underground to increase the updraft in the return shaft. This allowed for a larger quantity of air in circulation. When mines went deeper and became larger, mechanical ventilation became necessary and was first accomplished by steam-driven fans. These fans became more prevalent as furnaces were prohibited in underground mines, especially after the Avondale disaster in Pennsylvania in 1869 (Roy, 1876). Eventually, these fans were replaced by more powerful, electrically [ ]

Provide a rapid, reliable means of warning underground miners of a fire or other emergency. Approach An ultalow-frequency electromagnetic signaling system was designed, breadboarded, and tested at various under around mines. How It Works Current fire warning systems for underground mines, such as stench, audible alarms, and messengers, arc slow, unreliable, and seldom achieve total mine coverage. An ultralow-frequency electromagnetic fire warning alarm system with true through-the-earth signaling capabilities was developed to solve these problems. The system was originally designed for high-back room-and-pillar mines where stench systems are unusable due to the low velocity of mine air flow. However, the system has an application to all underground mines.

Jan 1, 1988

By R. J. Matetic

The objective of this U.S. Bureau of Mines hydrologic-subsidence investigation was to evaluate the effects of longwall mining on the local ground water regime through field monitoring and numerical modeling. Field data were obtained from multiple-position borehole extensometers (MPBX's) that were used to measure subsurface displacements. Survey monuments were installed to measure mining-induced surface deformations. Numerous drawdown and recovery tests were performed to characterize hydrologic properties of the overburden strata. Coreholes were drilled above the study area to determine lithologic and strength characteristics of the overburden strata using the rock samples collected. Electronic recorders were installed on all monitoring wells to continuously monitor ground water levels in coordination with mining of the longwall panels. A combined finite element model of the deformation of overlying strata, and it's influence on ground water flow was used to define the change in local and regional water budgets. The predicted effects of the postmining ground water system determined by the model correlated well with field data collected from the fieldsite. Without an infiltration rate added to the model, a static decrease of 3.0 m (10 ft) in water level would occur due to mining of both longwall panels and if an infiltration rate was inputted in the model, no predicted long-term effects would occur to the ground water system.

Jan 1, 2010

During the summer of 1973 we were asked to perform a theoretical investigation of the propagation of low frequency (LF) radio waves down deep (10,000 feet) hoistshafts* for the case where the hoist cable ("rope") is the only metal conductor present. Propagation is by means of the TEM coaxial mode of transmission in which the hoist cable serves as the inner conductor and the surrounding rock acts as the outer conductor. Since the rock is a relatively poor electrical conductor the current in the outer conductor of the coaxial line is not confined to a very thin surface layer as in a metal coaxial cable, but spreads radially to a distance that is generally many times the shaft diameter. This feature of the wave propagation requires a more sophisticated theoretical treatment than the approximate skin-depth theory that is adequate for metal coaxial lines. In this Part we treat the hoist shaft wave propagation loss, characteristic impedance, and the field current distributions in the surrounding rock medium. We also show that the large penetration of the wave into the rock outer conductor does not present a difficult problem with regard to coupling the transmitter or receiver to the transmission line with a minimum of insertion loss, but that the large impedance mismatch caused by the capacitance termination between the cage and shaft wall may well be the most significant contribution to overall system loss. Inductive coupling and impedance matching to the hoist rope/shaft transmission line are also treated briefly. Preliminary results indicate that a broad minimum in overall system loss should occur between 100 kHz and 1 MHz, possibly centered around 300 kHz. Further work is needed to better quantify this signal loss behavior, compare it with hoist shaft electromagnetic noise spectral data recently acquired by NBS, and identify the most favorable operating frequencies.

Jan 1, 1974

To suppress the natural bacterial action in acid mine drainage (AMD), the major contributor to acid formation. Approach Recycle partially-treated affluent back to the source of AMD within a mine, or to the coal or coal-waste stockpile. This effectively eliminates any further biologically-promoted AMD by inhibiting catalyzed weathering or oxidation by acid-forming bacteria. How it Works AMO-type effluents can be largely reduced by "recycling" the acidic outflow back to the source of AMD within a mine or to the Input side of a waste pile to percolate through the reactive pyrite and bacteria mixture. The bacteria in the cell thrive on the oxidation of ferrous to ferric iron through the electron transfer, Fe2 +[=]Fe3 + + e. Its reaction product [s, therefore, essentially ferric iron. While small quantities of Fe3 + will not interfere with the exponential multiplication of the bacteria

Jan 1, 1982

By J. P. McGee

As part of a joint U.S. Atomic Energy Commission-Federal Bureau of Mines program for using nuclear energy to supply process heat, a simulated nuclear loop has been constructed to test components. This loop has been operated for more than 1,800 hours at 100 p.s.i.g. Of this period, 23 hours were at 2,500° F. and higher; 540 at 2,000° to 2,500° F.; 840 at 1,500° to 2,000° F.; 200 at 1,000° to 1,500° F.; and 260 below 1,000° F. Leakage at flanges and welds was not a serious problem. A helium-recycle system with gas temperatures of 2,300° to 2,500° F. and a static pressure of 250 p.s.i.g. appears feasible. Difficulties were encountered with the recycle compressor due to thermal distortion of the impeller and shaft. The use of sealed bearings limits compressor operation to the life of the bearings.

Jan 1, 1960

By E. J. Gleim

In April 1932, the Bureau of Mines published Information Circular 6595, entitled "Data in Reference to Installation of Cables in Shafts and Boreholes", in which were described methods followed in various sections of the United States when electrical circuits are taken into mines by means of cables suspended in shafts and boreholes. In view of the present tendency to extend high-tension cables along entries and passageways from the bottom of the shaft, borehole, or other point of entrance to coal mines rather than over the surface, it is deemed that the various methods of installing such cables deserve careful consideration, particularly in mines in which gas and coal dust contribute to explosion hazards. This is especially true of localities where there is an inclination to restrict the extension of 2,300- and 4,000-volt circuits into the mines. Probably it is feared that accidental contact with the cables of such circuits may result in more serious shock than with lower voltages; also, it is possible that new circuits are regarded merely as explosion hazards additional to those already existing, regardless of the manner in which the new circuits may be installed. It is the firm belief of some engineers that the circuits can be installed so that they will not be damaged by wrecks or roof falls, thereby eliminating the hazard of explosion from this source while at the same time making the chance of accidental contact remote if not impossible. Moreover, some believe that fire hazards from direct-current systems can be reduced by keeping motor-generator sets close to load centers. Thus, although the alternating-current circuits would be lengthened, the size and extent of direct-current circuits would be kept to a minimum.

Jan 1, 1939

By David W. Houseknecht

Probabilities of encountering coalbed discontinuities during vertical or horizontal drilling in a specific coalbed can be estimated based on analysis of mined-out areas of the coalbed where the size, shape, orientation, and distribution of discontinuities are known. The result-ant probability estimates can be applied to cost-risk evaluations of drilling programs proposed for exploratory, developmental, or methane drainage purposes in undeveloped areas of that coalbed. Data compiled from mine maps of the Beckley Coalbed in southern West Virginia were used to estimate the probabilities that discontinuities would be encountered in two illustrative hypothetical drilling programs--one for drilling vertical boreholes and the other for drilling horizontal boreholes. Analysis based on a mined-out area of the Beckley Coal bed indicated that vertical methane drainage boreholes spaced 1,000 feet apart in a square grid pattern would each have a 29 percent probability of encountering a discontinuity in a geologically unexplored area of the coalbed. It was also determined that exploratory vertical drilling could locate most of the discontinuities if a borehole spacing of 2,500 feet were used. For horizontal drainage boreholes in the Beckley Coalbed, the analysis indicated a linear relationship between hole length and the probability of encountering a discontinuity.

Jan 1, 1982

By Peter F. Steidl

As part of the Bureau of Mines methane control program, the Upper Free-port coalbed was studied in Fayette County, Pa., where this coalbed lies about 650 feet below the Pittsburgh coalbed and contains the largest remaining reserves of any coalbed in the county. Coal and overburden isopachs, structure and joint pattern maps, and a fence diagram were prepared using data from gas and oil exploration logs and coal outcrops. These maps will aid in deter-mining the need and/or feasibility of degasifying the Upper Freeport coalbed in the study area. Much of the coalbed in this area is under 600 to 1,400 feet of overburden. By correlation with data from the Pittsburgh coalbed, the gas content at depths of this order is estimated to be between 140 to 300 cf/ ton of coal, for a total of 190 to 400 billion cubic feet of methane in this coalbed in Fayette County.

Jan 1, 1977

By Leland A. Yerkes

Refining aluminum from crude aluminum alloys by the subhalide reaction was investigated to develop a method of producing aluminum by means other than electrolysis of its oxide. The best materials and design for the apparatus and also optimum operating conditions, including temperature, pressure, vapor flow rate, and composition of alloy charge were studied. In the subhalide process, aluminum-trihalide vapor reacts with aluminum in the alloy under high temperature and low pressure, forming volatile aluminum monohalide which reverts to aluminum metal and aluminum trihalide on cooling. The only halide used in this investigation was aluminum trichloride. The crude aluminum-silicon alloys used as the principal raw material contained from 21.9 to 36 percent aluminum, and significant quantities of iron and titanium. These alloys were produced by direct electric smelting of clays. Graphite tubing that was heated by an induction coil proved to be satisfactory material for the laboratory reactor chamber, Enclosed in an insulated glass or quartz pipe, the reactor was used in both vertical and horizontal positions with various baffle and tray arrangements for directing the trihalide vapor both over and through the alloy. Aluminum trichloride vapor was generated in the sublimer at one end of the glass pipe, passed into the reactor where contact was made with the crude alloy, and aluminum monochloride gas was formed. When the gaseous mixture of aluminum monochloride and unreacted tri-chloride passed out of the reactor and entered the condenser, the gases were cooled to 900° C. or less, causing the monochloride to disproportionate into aluminum and aluminum trichloride vapor. The aluminum was deposited on the condenser walls while the aluminum trichloride vapor was carried out of the condenser and into the opposite end of the glass pipe where it solidified on the cooled copper coils.

Jan 1, 1961

By D. S. Kingery, F. F. Kopsch

The practice of using two or more main ventilating fans is common at large coal mines throughout the coal-mining industry. To assure adequate and efficient ventilation at may mines, such multiple-fan systems are necessary. The hazards associated with interrelated ventilating currents if a fan fails are controversial, and to date little effort has been made to study this specific problem and to determine corrective measures. The obvious questions are: 1. Is there a hazard? 2. Under what circumtances does it exist? 3. How serious is it? 4. What are corrective measures? Most members of the mining fraternity agree that reduced quantities of air and changed airflow patterns introduce potential hazards, especially where gaseous conditions exist when mechanized methods are used in concentrated mining 0 The seriousness of the hazard depends on the ease with which methane accumlates in face areas or haulage roads, the quantity of methane in workedout areas, and the extent to which reversed air currents interfere with escape and recovery operations after mine fires or explosions. These studies cover three mines and give the distribution of air for the specific conditions show. Each mine probably has somewhat different airflowpressure relationships between fans. This depends on the number of fans, the

Jun 1, 1959

By J. E. Tiffany, Z. C. Gaugler

"In presenting this list of permissible explosives and blasting devices, the Bureau of Mines desires to call attention to pages 20 and 25 outlining the conditions in use under which, and only under which, the explosive or blasting device is permissible.In view of a recent publication recounting trade practice favoring the use of a blasting device without stemming, particular emphasis is placed upon condition 4 on page 20 and condition 2 on page 25. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming.PERMISSIBLE EXPLOSIVES TESTED UNDER SCHEDULE 17CAn active list of permissible explosives was published in October 1938 as part of Bureau of Mines Report of Investigations 3421, under the title ""Active List of Permissible Explosives and. Blasting Devices Approved Prior to June 30, 1938."" This list included 191 brand names.Changes in the list that have been authorized to June 30, 1939, placed 56 additional brands of permissible explosives on the active permissible list as a result of tests, changes in brand names, or transfer from the inactive list. Fifty-seven permissible explosives were transferred from the active to the inactive list. The brand names of four explosives were rescinded curing the year. The present list contains 18G brand names. The brand names of the Permissible explosives placed on the active list are as follows:"

Sep 1, 1939