Search Documents

By H. P. Greenwald

About mid-December 1936, the safety director of a large coal corporation visited the authors at the Bureau's Experimental coal mine to discuss a rock-dust barrier he had invented primarily for use in trackless entries of coal mines. The rock dust in this device was carried in its original paper containers and means were provided for ripping these open so that the dust might be scattered in the path of an explosion. The inventor termed the device a "bag barrier", and this term has been adopted in the present paper for convenience. At that time the device was in an early stage of development, and the inventor felt that the barrier should be tested to determine whether it had enough promise of being successful to justify further development. The matter was taken under consideration and finally three tests were made during the week of February 15, 1937. It was concluded that while the device did stop an explosion in two of the three tests, it was much loss effective than ordinary rock dusting, and that too few data were obtained to permit direct comparison with tests of other barriers. Apparently, the conditions under which the device could, be successful were somewhat limited, out the limits could not be defined without additional tests.

Jan 1, 1938

By R. D. Brown

There are techniques for separating aluminum alloys from mixed scrap, but there are no efficient ways to separate wrought aluminum from cast aluminum. This Bureau of Mines report describes a novel technique for separating mixed aluminum alloy scrap into cast and wrought aluminum alloy fractions. The technique, which uses conventional heating, fragmentizing, and screening equipment, exploits differences in the mechanical properties of cast and wrought aluminum alloys at elevated temperatures. The cast alloys become brittle at high temperatures owing to intergranular melting of regions of eutectic composition. This melting begins to occur as the solidus temperature for each alloy is reached. Solidus temperatures for casting alloys generally range from 520° to 580° C, but are above 600° C for most wrought alloys. Thus, the casting alloys are easily fragmented while the wrought alloys remain ductile in the proper temperature range. Starting with a mixture containing approximately 80 pct cast and 20 pct wrought alloys, fractions of 100 pct cast and 98 pct wrought have been produced.

Jan 1, 1985

By R. C. Buehl

Pilot-plant tests have been in progress at the Bureau of Mines, Pittsburgh, Pa., on the recovery of manganese from open-hearth slag.3/4/5/ In the process, 1 the slag is first reduced in a blast furnace to make a high-phosphorus spiegeleisen containing 12 to 22 percent manganese. A slag containing 55 to 60 percent manganese is made from this spiegel by oxidation in a basic-lined converter. The metal from this blowing operation contains about 3 percent phosphorus, 1 percent manganese, and less than 1 percent carbon. Economic efficiency in the manganese-recovery process requires that this metal be converted into steel. Because of its high phosphorus content the metal is suitable for blowing in a basic-lined converter. In most of the tests described in this report, metal of this composition was used as the starting material in a 1-ton, side-blown, basic-lined converter. Although basic-lined converters are not used for steel production in the United states, in Europe a considerable portion of the steel is made in them. Open hearths largely have replaced converters for steelmaking in the United States; mainly because open-hearth steels have better physical properties than converter steels because of lower nitrogen and phosphorus contents. However, by improving converter design and operating technique during the past 15 years, metallurgists have found that low-nitrogen steels with physical properties equal to open-hearth steels can be produced in converters.6/ Tests at Jones & Laughlin steel Corp. with side-blown, acid-lined converters of 3 and 22 tons capacity showed that steel with a low nitrogen content comparable to that of open hearths operating on scrap charges could be made by surface blowing.7/

Jan 1, 1955

By A. J. Miscoe

A unique machine for inducing bending fatigue in wire ropes was built at the U.S. Bureau of Mines' Pittsburgh Research Center. This machine can produce nine levels of degradation through repetitive cycling of long samples of wire ropes of the types used in the mining industry. This report provides an analysis of the results of the first wire rope to be fatigued on this machine. These results have indicated that as a wire rope accumulates bending cycles, its strength first decreases because of wear and then in-creases due to cold working of the wires. As the amount of cold working increases, more and more of the embrittled wires break and the strength of the rope decreases rapidly. In this test, application of several of the regulatory retirement criteria to various sections of the rope suggests that there may be some inconsistency among them.

Jan 1, 2010

By T. H. Jeffers

The Bureau of Mines conducted laboratory tests to devise a procedure for extracting copper from low-grade discarded mill tailings. A solid extractant consisting of an organic solvent extraction reagent adsorbed on granular activated carbon was investigated and proved to be satisfactory for extracting copper directly from leach pulps. When this material was used in a cyclic leaching, stripping, and electrowinning pro-cess, 95 pct of the acid-soluble copper was recovered from oxidized mill tailings. The weathered tailings contained 0.24 pct Cu (total) and 0.20 pct acid-soluble Cu. The copper was recovered as cathodes containing, in parts per million, 1.6 Pb, 3.6 Fe, 0.5 Sb, 1.5 AI, 1.9 Mn, and <1 Mg.

Jan 1, 1985

By Welby G. Courtney

The Bureau of Mines conducted a field test program in the Pittsburgh coal seam to investigate the effect of water sprays in the suppression of respirable dust being formed while cutting with a continuous-mining machine. Emphasis was given to the location of spray nozzles on the top and bottom of the cutting boom. Results showed that (1) sumping caused about 60 percent of the dust escaping the face area, and shearing and loading caused the other 40 percent; (2) during sumping, top and bottom sprays were equally effective in dust suppression and reduced dust ~13 percent; (3) during shearing and loading, bottom sprays reduced dust 61 percent and were about 50 percent more effective than top sprays; (4) the combination of top and bottom sprays was slightly more effective than the separate systems, but water consumption increased 60 percent; and (5) inclusion of throat sprays decreased dust reduction by removing some of the water from top and bottom sprays where it was more effective.

Jan 1, 1978

By Yael Miron

Two recent unplanned detonations occurred during blasting operations in sulfide-bearing ores in a Nevada gold mine. Other premature detonations have also reportedly occurred at other Nevada, California, and Arizona operations within the past few years, with increasing frequency. Unplanned or premature detonations can be extremely hazardous to life and can cause extensive property damage. A miner was injured in one of these occurrences. This report, by the U.S. Bureau of Mines, is intended to acquaint personnel involved in such mining activities with the basic causes for these accidents. These causes include the exothermic oxidation of pyrite (FeS2) and formation of ferrous sulfate (FeS04), the exothermic and energetic reaction of the ferrous sulfate with ammonium nitrate-fuel oil (ANFO)-based explosives, and the associated elevated temperatures that can set off detonators and explosives in the boreholes. Recommendations for safe operation by the Mine Safety and Health Administration, the Bureau, and the mine involved with the recent incidents include monitoring temperatures in the blast holes, analyzing for sulfate and ferrous ions, and limiting the time between loading and firing in accordance with conditions in the blast holes. Other procedures for safe operations should fit specific conditions in, the mines.

Jan 1, 1992

By T. E. Purcell

(a) Moisture. - Moisture, "as fired," is specifically significant in pulverized-coal firing because of its effect upon the continuity of raw-coal feed to the pulverizer, pulverizer capacity, flame stability, and speed of ignition. The extraneous moisture content is a rough index of potential difficulties in unloading and maintaining the flow of raw coal to the pulverizer and of pulverized coal to the furnace, with the troubles increasing geometrically as the percentage increases. Sticking or other stoppage of coal flow at any point between the bunker and the furnace is especially serious with pulverized-coal firing because there is danger of immediate loss of output. Where moisture is a problem, the designer must exercise great care in the design of coal-handling and preparation apparatus.

Jan 1, 1951

By A. C. Smith

The U.S. Bureau of Mines conducted a study to evaluate the effect of underground mining conditions on the activation of automatic sprinkler heads. Sprinklers were exposed to liquid fuel fires in a rectangular tunnel at airflows of 0, 45, 90, 150, and 250 m/min to determine the effect of ventilation and fire size on the time to activation. As the airflows were increased, the time to activate the sprinklers for a given fire size increased. Also, as the fire size increased, the activation time decreased. Temperature profiles of the tunnel showed that the maximum temperature near the roof was shifted downstream as the airflow increased. Experiments to determine the effect of rated activation temperature and response time index (RTI) value on activation time showed that the time to activate increased with increasing activation temperature, and decreased with decreasing RTI value. Exposure to the mine environment showed little effect on the activation times in large-scale experiments, and no significant effect in laboratory experiments. The results showed that airflow can have a significant effect on the activation times of automatic sprinklers. This needs to be considered in the design of effective sprinkler suppression systems for ventilated areas.

Jan 1, 2010

By D. B. Dow

"In the natural-gas Gasoline industry, the methods used in determining the amount of gasoline in natural gas are many and varied; they include the specific-gravity test, laboratory tests involving absorption, charge in volume of the gas or in the absorption medium, absorption in charcoal with subsequent distillation, compression of the gas which results in the condensation of the gasoline, and the absorption of the gasoline vapors in an absorption oil, from which the gasoline is distilled and measured. Each of these various tests has advantages, and disadvantages. It is however, conceded in the industry that the tests in which the gasoline is obtained and measured as such are the more reliable.This paper deals with certain factors which should be considered in making absorption tests using ""mineral seal oil"" as an absorbent; this method of testing is widely used not only in the field, but in control work in absorption gasoline plants where the gasoline content of the intake and discharge gas is determined daily. In control work it is frequently found that the plant produces more gasoline than the tests show, which gives the plant the appearance of making more gasoline than is actually present in the gas treated, or in other words operating at more than one hundred per cent efficiency. Obviously then, the tests as made in these cases are in error, and in hope of correcting some of these variances, the following factors have been studied at the U. S. Bureau of Mines petroleum station at Bartlesville, Oklahoma."

Aug 1, 1920

By Aldo L. Furno

Sufficient quantities of combustible vapors are released by some sulfurs to produce flammable atmospheres under prolonged storage. Hydrogen sulfide and carbon disulfide appear to be the principal flammable constituents in the vapor space above molten sulfur. If sufficient carbon disulfide is present, ignition of the vapor-air mixtures can occur spontaneously on contact with the heated surfaces found within storage tanks.

Jan 1, 1963

By David Cooper, Susan Robertson, William Wiehagen, Launa Mallett, Charles Vaught, Joan Dickerson, Richard Conkle, ROBERT PETERS, Mike Brnich, Charles Urban

This trainer’s guide is designed as a reference manual. The purpose is to offer information and examples to skills trainers to assist them in structuring training for new operators of Walk-Thru roof bolting machines. Trainers can use this manual as a resource for helping trainees learn, understand, and apply knowledge and skills. In this sense, the guide is not prescriptive. It is designed to offer information and trigger ideas on what might be done to accelerate learning to those who are new to the roof-bolting task. On-site trainers can modify this guide to fit their conditions, machines and equipment, and work procedures. They can integrate roof control plans, company policies and procedures, and operators’ manuals from the manufacturers of the original equipment into this guide. Every trainee is different and will come to the job with varying levels of relevant knowledge and skills. The trainer’s decisions on where to start, how to organize the on-the-job and classroom training portions, and when and how to offer different aspects of the training will be based on (1) a pretraining assessment of the trainee’s knowledge and skills and (2) the trainer’s experience in conducting skills training. The “Skill Check” section might be useful for deciding where training should start among miners who have underground experience but limited knowledge of roof-bolting techniques. Every job carries a learning curve and likely has a number of “teachable moments” where significantly new knowledge and skills can be learned. The videos on the DVD that accompany this guide can be shown at the beginning of training to give trainees an idea of what the job entails and related requirements. They can also be used within the training cycle (after the trainee has some experience in the job) to reinforce key points or as a trigger for eliciting questions about particularly difficult parts of the job. The video segments are meant to be visual models of good performance. They are designed to elicit discussion on good (lower risk) ways to do the job. In this context, they can be used very creatively at different times within the training cycle. The section on “Talking Points” offers a number of questions that can be used in the classroom to support and elaborate on certain aspects of the job duties. If the trainee has a fair amount of underground experience, some of the questions can also be used to support the pretraining assessment (i.e., skill check) of knowledge and skills. Likewise, some of the questions can also be used while teaching on the job to reinforce key points affecting safety, production, or maintenance. The section dealing with a mine’s roof control plan should be used at various times in the training cycle to make sure the trainee understands the plan and knows how to apply it in performing the job. The supplemental materials offer additional resources that can be used to support initial job training or follow-up. Learning continues well after an individual has been trained. The supplemental materials can help reinforce good operating skills and provide an opportunity for further discussion on better ways to do the job.

Jan 8, 2006

By N. E. Hanna

Experience with the current version of gallery test 4, in use since 1913 to evaluate the incendivity of permissible explosives in the presence of coal dust, has shown the procedure to have inadequate discrimination. Consequently the Bureau of Mines used the up-and-down method of statistical design to investigate the incendivity of permissible explosives in the presence of coal dust and gas. A suitable device was developed to measure coal dust concentrations in the air-gas mixtures and to disperse the dust in the gallery atmosphere. A proposed testing method which uses suspended shots in a predispersed coal dust-gas-air mixture was evaluated. The new method can discriminate between different explosives with respect to their incendivity. Maximum ignitibility of the coal dust cloud by permissible explosives occurred in the vicinity of 0.3 oz/cu ft. About 10% sodium chloride in permissible explosive formulations had a very significant effect in reducing the probability of igniting coal dust. Bundled charges were more incendive than column charges.

Jan 1, 1966

By C. H. Gorski

Evaluation of raw materials for mineral wool is one phase of the Bureau of Mines broad program for the more effective utilization: of our mineral resources. The experimental work and test-evaluation results on several raw materials as useful components for the production of mineral wool are presented in this report. Samples from all sections of the United States, including copper slag from Tacoma, Wash., pebble phosphate slime from Florida, and granites from Massachusetts and Minnesota, have been blown into mineral wool successfully in the laboratory tests. Maximum conservation of the Nation&apos;s mineral and manpower resources requires maximum utility of those resources. Al though the domestic reserves of oil, gas, and coal are tremendous, judicious use of these fuels through the use of proper insulation will insure the highest thermal efficiency. The effectiveness of mineral wool as a heat-insulating material has assumed an increasingly important role in the national economy, and it has become a fuel saver in countless applications. The most immediate concern to many is the use of mineral wool in the home, which promotes uniform temperature and minimizes drafts by reducing heat transfer through the walls, ceiling, and floors. There are, however, many industrial and commercial uses that require large volumes of mineral wool each year.

Jan 1, 1951

By H. R. Hardy Jr., E. J. Kimble Jr., H. W. Shen

"The primary objective of this research project is to study the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. Secondary objectives include the investigation of the acoustic emission technique as an indirect method for coal dust characterization and remote bit wear monitoring. The results of the project will be useful in developing efficient coal cutting techniques which significantly reduce the harmful coal dust components, and in providing methods for remote monitoring of bit condition and associated coal dust character. This paper will outline recent experiments carried out on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. During the experiments acoustic emission and a variety of other mechanical parameters were monitored. · A commercially available artificial intelligence computer package, namely: JCEPAK (Intelligent Classifier Engineering Package), has been utilized to provide a powerful and objective means for AE waveform analysis. This program is able to evaluate a number of features of each AE event and to make objective comparisons between AE signals associated with different loading or cutting parameters. Finally, the paper will discuss the results obtained from a variety of coal breakage tests.INTRODUCTIONStudies to date clearly indicate that the reduction of the severity, and eventual elimination, of Coal Workers' Pneumoconiosis (CWP) depends on gaining fundamental understanding in a number of major areas. These include dust generation and entrainment, transportation, suppression, medical effects of dust and possible treatment. At present a project is underway by the authors to investigate the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. An important aspect of this on-going project is the development of acoustic emission (AE) criteria which will make it possible to carry out remote monitoring of coal cutting operations. Suitable on-line analysis of monitored AE data would allow engineers to evaluate factors such as shearer bit condition and cutting efficiency, and to quantify the particle size and shape distribution of the generated dust. The on-going AE studies are fundamental in form and were undertaken to evaluate the general feasibility of AE monitoring techniques using simplified coal cutting procedures. This paper will outline recent experiments on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. Additional information on these studies are presented elsewhere [4]."

Dec 1, 1996

By G. L. Hundley

An anhydrous chlorination process has been developed by the Bureau of Mines for the production of copper, ferric oxide, and sulfur from chalcopyrite. The first part of the process is a chlorination step in which elemental sulfur and a mixture of iron-copper chlorides are produced. This paper describes the second step of the process in which the copper and iron chlorides are reacted with oxygen to selectively convert the iron chloride to ferric oxide and chlorine leaving the copper in the chloride form. The chlorides are pulverized and dropped countercurrent to a flow of oxygen in a vertical 20-cm-diam. reactor at 800° C. By leaching with brine, the copper chloride may be separated from the insoluble iron oxide and reduced to copper powder by electrowinning. It has been demonstrated that 70 to 80 pct of the iron can be converted to oxide in a single-stage operation with a chlorine content in the offgas of 80 pct. After removal of the oxygen, this chlorine could be recycled to the chlorination step. A two-stage operation will convert 98 to 99 pct of the iron in the mixture to insoluble oxides. The offgas from the second stage contains 70 pct chlorine.

Jan 1, 1974

By C. H. Schack, K. C. Dean

An investigation was made to devise and evaluate a flexible flotation method for beneficiating typical tactite types of calcareous scheelite - bearing ores ; these scheelite - bearing ores are available in large tonnages in deposits containing 0.2 to 0.3 pct tungsten trioxide . The objective was to achieve a high recovery of the tungsten in concentrates , containing a minimum of 10 pct WO3 , that would be suitable for chemical processing into high- quality synthetic scheelite . The principal problems encountered and resolved by bench- scale flotation tests on ore samples from five different deposits were to define the conditions and reagent combinations essential for ( 1 ) achieving selective flotation of a small amount of scheelite from a large amount of calcite and ( 2 ) controlling the effect of small amounts of calcium , magnesium , and iron salts in the ores and water used . The flotation process was evolved from batch tests and continuous runs in a pilot - scale mill with a capacity of 100 lb per hour . The flotation process comprised ( 1 ) removal of sulfide minerals , ( 2 ) conditioning the residual ore pulp with sodium carbonate , quebracho , and trisodium phosphate , and ( 3 ) rougher flotation and single - stage cleaning of a scheelite concentrate . In a pilot plant run , over 91 pct of the tungsten was recovered from ore containing 0.27 pct WO3 , in a concentrate containing 11.2 pct WO3 .

Jan 1, 1964

By M. M. Tilman

The Bureau of Mines conducted research to evaluate superplastic behavior in commercial magnesium-base alloys AZ6IA, ZK60A, ZW3, AZ3IB, ZWI, and an experimental Mg-12 pct Al alloy. Strain-rate sensitivity indices (m-values), maximum elongations, and effects of superplastic elongation on tensile properties were determined on fine-grained sheet. Inert-gas-pressure hemisphere-forming tests were conducted on selected sheet stock of the five alloys. Formability trials on AZ31B alloy sheet were conducted on industrial equipment for comparison with commercial superplastic forming of Zn-AI alloy. Closed-die-forming tests were performed on extruded ZK60A rod. All alloys exhibited well over 100-pct elongation, indicating superplasticity, at temperatures and strain rates near the maximum m-values. Tensile properties were generally reduced following 100-pct superplastic elongation, but not to an extent that would preclude use of the commercial alloys in the superplastically deformed condition. The potential for industrial superplastic forming of AZ31B sheet was indicated by hemisphere forming in the laboratory and substantiated in industrial forming trials.

Jan 1, 1982

By G. W. Grove

Coal-mine officials and those who are preparing to become officials should be familiar with the instruments and devices that are employed rather commonly in and around mines and should know how to use them with safety and efficiency. Among these axe instruments and devices used in determining the pressure, velocity, volume, and certain other conditions of ventilation and in detecting the more common mine gases, such as methane, carbon monoxide, and hydrogen sulphide, or a deficiency of that very important agent, oxygen. Water gages, anemometers, barometers, psychrometers, flame safety lamps, lamp-testing boxes, and methane, carbon monoxide, and hydrogen sulphide detectors are described and their use and operation discussed in this paper.

Jan 1, 1938

By W. C. McBee

Over the past several years the Bureau of Mines has developed a sulfur concrete (SC) technology in which chemically modified sulfur is mixed with suitable mineral aggregates to produce construction materials that are resistant to corrosion by acids and salts. Modified SC materials have been tested in actual operating conditions in 50 corrosive process environments at 40 commercial plants. SC components ranging from small test coupons to 4-ton acid sump tanks were fabricated and installed at plant locations where chemical corrosion was destroying conventional concrete materials. Through cooperative agreements with several companies, floors, retaining walls, and foundations were cast in place us-ing SC materials, then monitored for resistance to corrosion and retention of strength properties.

Jan 1, 1983