Search Documents

By F. W. Penn

An aircraft auxiliary power unit (APU) was used as an exhaust source for evaluation and refinement of sampling and analytical procedures for gas turbine engines. The unit was also used to determine the emission characteristics of APU's in service and to study the effect of fuel composition and combustor design on exhaust emissions. Carbon monoxide, carbon dioxide, oxides of nitrogen, hydrocarbons, aldehydes, particulate loading, and odor were measured at engine operating modes representing the duty cycle encountered in airline operation. Analyses showed good repeatability, and adequate sensitivity was attained in these experiments. Smoke opacity measurements were not taken owing to the lack of a high-sensitivity smokemeter. Results showed that the minimum emission levels occurred with the standard combustor and Jet A fuel. Emission rates were highly dependent on test mode, but emission patterns as a function of test mode were similar for all fuels and combustors tested. A comparison of three identical design production combustors showed a variation in average emission rates of less than 5 pct.

Jan 1, 1973

By William Hustrulid

The National Institute for Occupational Safety and Health (NIOSH), as part of a comprehensive program to improve mine safety through the widespread acceptance of careful excavation principles in drifting, have revisited standard drift round design concepts. Although the initial emphasis was on contour row design and providing improved design tools for blasting with de-coupled charges, the focus has broadened into the development of a general gas pressure-based drift round design approach. The concept of a damage radius (Rd) for a given explosive-hole-rock mass combination is introduced. With the damage radius as the basic building block, the blast holes are positioned on the face, beginning with the buffer row, to achieve the desired excavation size, shape and smoothness. The design of the contour row of holes is also performed using a pressure-based approach. The paper presents in some detail the overall approach and the required gas pressure-based design equations.

Jan 1, 2007

By Potts J. D.

Installation of a horizontal air-blocking shelf around the inside perimeter of the surface mining drill deck shroud is proposed to improve dust capture. Without the use of this shelf, a strong Coand? effect airflow pattern results in dust leakage to the environment, especially at the shroud-to-ground interface. Bailing air exits the drill hole and travels along the drill steel to the underside of the table, where it fans out across the bottom of the drill table and continues down the sides of the shroud. This dust-laden bailing air then strikes the ground and fans out under gaps between the shroud and the ground. The proposed shelf prevents dust-laden air from striking the ground by redirecting it toward the center of the enclosure, where it can be captured. Laboratory tests demonstrated that the shelf reduced dust levels outside of the shroud by 81% under operating conditions consisting of a 1.9:1 collector-to-bailing-airflow ratio and a 51-mm (2-in.) gap between the shroud and ground. The shelf was 152-mm (6-in.) wide and was located at a height equal to 2/3 the distance measured from the bottom of the shroud to the bottom of the drill table. The air-blocking shelf was also capable of overcoming the adverse impact of vertical leakage along the shroud seams as long as this leakage was confined to an area below the horizontal plane defined by the shelf location.

Jan 1, 2008

By Harley A. Coy

This paper, describing the mining methods and practice at No. 2 mine of the American Zino Co. of Tennessee at Mascot, Tenn., is one of a series of papers issued by the Bureau of Mines presenting the mining methods and costs in various districts throughout the United States. Its purpose is to summarize methods recently put into practice whereby increased efficiency has been effected. These improvements have to do principally with mill-hole mining, slushing, contract labor, and bonuses. In general, this paper supplements earlier articles and brings them up to date. ACKNOWLEDGMENTS The author acknowledges the assistance of M. H. Newman, geologist of the American Zinc, Lead & Smelting Co.; of William Black, assistant superintendent of mines; of P. M. Arthur, director of personnel; and of the engineering staff. The paper has been approved by H. I. Young, vice president and manager of operations.

Jan 1, 1930

By Wallace W. Roepke

The Bureau of Mines has a well-established health and safety research effort directed to fundamental studies of the mine cutting system. This report describes the ignition danger of using cutting bits with flat wear area on still-intact carbide inserts.

Jan 1, 1983

By Arthur L. Murray

"During recent months much criticism as to the efficiency of mine labor has been heard from various, sections of the country. No doubt much of this criticism has been well founded. The present lack of efficiency and of stability is due primarily to a spirit of restlessness and partial irresponsibility engendered during the transition from war conditions to peace time conditions. This spirit or unrest not only among the laboring classes but in every branch of the human family following a period of intense nervous tension in a nation appears to be a natural sequence of war and beyond the control of man. This condition will gradually disappear, and the majority of our people will again assume their natural order of living, but labor will for a considerable period be sensitive to these influences, whether they be exerted for good or for evil. Employers of labor should take cognizance of this fact and bend every effort towards the development of measures that promote efficiency and permanence of the working force.Labor efficiency depends upon many and varied factors. Some of these factors as applied to mine labor are briefly enumerated in the following paragraph:Selection and Placement of Manpower:In the selection of men the two main considerations are physical ability and adaptability. The laws of mechanics should be applied in the selection of men as in the selection of machinery. If a machine is required for a certain class of work, the type of machine known to be mechanically fit for such work is selected. Likewise, men should be selected with regard to their physical and temperamental fitness for the kind of work expected of them."

Apr 1, 1920

By Raymond B. Ladoo

"The recent discovery and exploitation of petroleum territory have resulted in the enactment of new petroleum laws in most of the South American Republics. The activities in the discovery of these new fields were engendered by the knowledge of the fact that present producing fields must within well defined periods be exhausted. Oil operators were willing to take the initial steps in exploitation in the absence of legislation that applied strictly to petroleum operations. The enactment of modern legislation in many of these Republics encouraging and protect¬ing exploitations may cause tremendous oil activities in these countries, and the results may be comparable with the magnitude of the undertakings and the prestige of the companies now entering this territory.These, oil fields are admirably located for convenient distribution of petroleum by water to all the Nations using oil as fuel for shipping and industrial concerns. The oil markets of the western coast of South America will derive immense benefits from the Panama Canal. This navigation route brings these markets into direct ocean shipment with the Atlantic coasts of the Western and Eastern Hemispheres.One deterrent to oil production in the Republics of South America is the want of inland. transportation facilities, but the recent laws of these Republics without exception provide for acquiring rights of way for pipe lines and other modes of transportation; and doubtless the great interests and. syndicates already operating in these regions will, as production increases, provide ample pipe line transportation sufficient to convey to the coast the oil produced. It way be assumed, from the legal guarantees afforded, and from operating equipment and machinery that are now being concentrated that refineries will be erected at shipping points for the purpose of making these petroleum products accessible to the world."

May 1, 1921

By Fred N. Kissell

Methane flows and pressures were measured in mines in the Pittsburgh, Hartshorne, and Pocahontas No. 3 coalbeds. From the data, the permeability of each of these coalbeds was computed. It was found to depend strongly on the type of coal and on the amount of water in the coalbed, and it was found to increase with time. All of the coalbeds had a high-permeability zone adjacent to the face or rib, and the Pittsburgh bed exhibited directional anisotropy. Surprisingly, little or no overburden effect was observed.

Jan 1, 1972

By Karl C. Dean

The Bureau of Mines stabilized 10 acres of windblown copper mill tailings at McGill, Nev., by a combination chemical-vegetative procedure. Legumes, winter wheat, wheat-grasses, and wild rye were seeded, and the area was subsequently sprayed with a resinous adhesive chemical to stabilize the sands until the vegetation could grow. During the year since treatment, the area has been well stabilized against wind erosion. The established vegetation appears to be capable of self-perpetuation and renewal without irrigation. The cost of stabilizing the area was $135.50 per acre.

Jan 1, 1969

By Martin Hertzberg

The concept of limit burning velocities, formulated in an earlier Bureau of Mines report (RI 8127), is applied to the problem of flame propagation through tubes of finite size. The limit burning velocity for conductive-convective wall-loss quenching (process b) is (Su)b = [aPe,] where the proper choice of critical Peclet constant, Pe, is determined mainly by the ratio of contact-perimeter loss area to flame-zone cross sectional area. This ratio of loss area to propagation area relates to the shape of the flame front and its control by buoyancy and by boundary conditions. The comparison of (Su)b with previously defined limit velocities for systems mixed by natural convection allows one to assess the influence of tube dimensions and boundary constraints on the "true" or earthly limits for the three directions of propagation. The flame quenching caused by inert powders is shown to be similarly described in terms of a limit burning velocity, (Su)?b. The tube's surface-to-volume ratio (~1/ro) is simply replaced by the powder's surface area per unit volume of the flammable mixture. Thermal loss quenching by these "internal walls" occurs at a critical Peclet constant somewhat higher than that observed for tubes, and the problem is complicated by the finite heat capacities of the powders and particle lag effects in the flame front.

Jan 1, 1980

By D. K. Ingram, G. L. Mowrey, T. R. Rehak

Problem: Blasting is a hazardous component of surface mining. Serious injuries and fatalities result from improper judgement or practice during rock blasting. This paper describes several fatal injury case studies, analyzes causative factors, and emphasizes preventive measures. Method: This study examines publications by MSHA, USGS, and other authors. The primary source of information was MSHA’s injury-related publications. Results: During the 21-yearperiod from 1978 to 1998, the mean yearly explosive-related injuries (fatal and nonfatal) for surface coal mines was 8.86 (95% CI: 6.38 -11.33), and for surface metal/nonmetal mines 10.76(95% CI: 8.39 - 13.14). Flyrock and lack of blast area security accounted for 68.2% of these injuries. This paper reviews several case studies of fatal injuries. Case studies indicate that the causative factors for fatal injuries are primarily personal and task-related and to some extent environmental. A reduction in the annual injuries in surface coal mines was observed during the ten-year period of 1989 - 1998 [5.80 (95% CI: 2.71 - 8.89) compared to the previous ten-year period of 1979 - 1988 [10.90 (95% CI: 7.77 - 14.14)]. However, such reduction was not noticed in the metal/nonmetal sector, i.e., 9.30 (95% CI: 6.84 - 11.76) for the period 1989-1998compared with 11.00 (95% CI: 7.11 - 14.89) for the period 1979-1988. Discussion: A multifaceted injury prevention approach consisting of behavioral/educational, administrative/regulatory, and engineering interventions merits consideration. Impact on industry: The mining community, especially the blasters, will find useful information on causative factors and preventive measures to mitigate injuries due to flyrock and lack of blast area security in surface blasting. Discussion of case studies during safety meetings will help to mitigate fatal injuries and derive important payoffs in terms of lower risks and costs of injuries.

By Irving Hartmann, Edward Thomas

"INTRODUCTION Adoption of rubber-tire shuttle cars underground in conjunction with mobile coal-loading machines has introduced new problems in the control of dust on mine roadways. Where this type of loading and transportation is used, development and extraction are generally rapid, with the result that much coal is spilled from the shuttle cars during normal operation, Coal in the roadways from this source and from sloughing of the ribs is ground to fine dust by the wheels of the 'shuttle cars and by the treads of the loading and mining machines. The coal dust usually is somewhat contaminated by pulverized rock, and the mixture could not be loaded with the run-of-mine coal without undue contamination of the product even if it were cleaned up promptly.The presence of large quantities of fine, loose dust, which is constantly stirred up and kept in suspension in air by the traffic, constitutes a grave explosion hazard, reduces visibility along the roadways, and is physiologically harmful to the workmen who breathe the air. From the operating standpoint the loose material is undesirable along the roadways because it provides poor traction for the trucks and thereby increases wear and power consumption. The dust-explosion hazard could be eliminated or reduced by frequent application of sufficient rock dust on the roadbed; but this would not remedy the other difficulties, and in fact it might intensify them. Where practicable, the most direct and effective safety measure is to clean up and remove promptly all dust that forms and settles on the roadways. Unfortunately, in many cases this procedure is not feasible. A third Suggested remedy is to prevent dispersal of the dust into the air and to promote its consolidation on the floor by wetting the dust particles.During the past few years several mines have used calcium chloride on shuttle-car roadways to allay the dust thereon. When exposed to the' humid atmosphere of the mine this salt absorbs Moisture from the air and deliquesces, and in this way wets the dust on the floor of the roadway. In a survey conducted in coal mines in southern West Virginia and in eastern Kentucky where calcium chloride has been in use, somewhat conflicting re- ports were received regarding the merits of the application, and several operators have abandoned the practice either because of actual or assumed disadvantages. The purpose of the study described in this report was to collect and correlate evidence and, on the basis of experimental data obtained in the field and in laboratory tests, to present a clearer picture of the factors involved in the allaying of dust by use of salts."

Sep 1, 1945

By S. E. Khalafalla

The extremely sluggish oxidation of steel scrap was appreciably accelerated when the charge was pretreated in aqueous solutions of sodium metavanadate or sodium molybdate. The degree of oxidation acceleration was inversely correlated with the melting point of the promoter oxide possessing the highest valency. The magnitude of oxidation enhancement exhibited a systematic inverse dependence on the duration of pickling processes; mere dipping of the oxidizable charge in the vanadate bath was most effective. In general, the rate of steel scrap oxidation increased with increasing concentration of the pickling reagent. The results are explained on the basis of the hydrolytic decomposition of the pickling agent with subsequent slow interaction with the metal surface, coupled with the tendency of vanadium to form polyanions in alkaline media. The data not only served to elucidate the mechanism by which catastrophic oxidation takes place, but also showed that the accelerating species need not be alloyed with the oxidizable metal; surface impregnation by minute amounts of the accelerating species can still produce catastrophic effects.

Jan 1, 1970

By Steven J. Schatzel, William P. Diamond

Coalbed gas content measurements are commonly used in mine safety as well as coalbed methane resource assessment and recovery applications. Gas content determination techniques generally fall into two categories: (1) direct methods which actually measure the volume of gas released from a coal sample sealed into a desorption canister and (2) indirect methods based on empirical correlations, or laboratory derived sorption isotherm gas storage capacity data. Direct gas content determination techniques may be further. subdivided into quick-crushing and extended desorption methods. The quick-crushing methods are primarily used in mine safety applications outside the United States, but have also been used for resource recovery applications. Quick-crushing methods rely on crushing the coal sample soon after collection to release all the desorbable gas, thus significantly shortening the amount of time required for desorption measurements. However, some data useful for resource recovery applications are lost. Extended desorption techniques are most commonly used for resource assessment and recovery applications where information on desorption rates is useful for reservoir modeling, and for fundamental coalbed methane research. Extended desorption methods allow the gases in the coal sample to desorb under controlled laboratory conditions until a defined low desorption rate cutoff point is reached. The sample may then be crushed to measure the amount of gas remaining within the sample. Direct method techniques for gas content measurement are the focus of this paper.

By John W. Frey

This paper presents one of a series of digests of foreign mining legis- lation and court decisions which is being prepared in advance of a general re- port relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Portugal, prepared from the best available information in Washington, has been slightly amplified in accordance with suggestions trans- mitted through the courtesy of the Department of State by Fred Morris Dearing, American Minister at Lisbon.

Nov 1, 1929

By Robert R. Stein

Occupational noise caused by the rock drills used in mining was investigated by the U.S. Bureau of Mines. Using a large reverberation chamber and an automated drill test fixture (ADTF), the sound power levels of mining drills were measured to determine if there are types of drills that are advantageous from a noise production standpoint. Test results show that while there are not large variations among types of drills, there are still some choices that could produce a positive effect on overall noise exposure. It is also shown that lower noise exposures are possible using larger drills because of higher production rates and better operator positioning.

Jan 1, 2010

By L. M. Demers, D. C. Kuhn, N. El-Ayouby, C. F. Stanley

"Oxygenated metabolites of arachidonic acid (MJ are produced by the alveolar macrophage (AM) and have been shown to mediate inflammatory reactions. We therefore assessed the production of eicosanoids by AM harvested from the lungs of rats ex· posed to a bituminous coal dust for 2 wk in an inhalation chamber in order to determine if AA metabolism was altered in a manner that may promote an inflammatory response in the lung. Exposure to coal dust resulted in a 66% increase in the number of AM harvested, an increase in thromboxane A2 (TxA;i) and leukotriene 84 (LTB,j) production to 222% and 181% of control values, respectively, and a decrease in prostaglandin E2 (PGE:i) production to '62% of control values. In AM harvested from rats allowed to breath clean air for 2 wk following coal dust exposure, PGE2 production returned to control levels but TxA2 and LTB4 production remained elevated. The TxA2 synthesis inhibitor UK 38,485 reduced TxA2 production in dust-exposed AM both immediately and 2 wk following exposure. Thus, exposure of rats to coal dust significantly alters the metabolism of AA in AM, with potentially important aspects of AA metabolism remaining altered even after a 2-wk recovery period. Based on the established role of eicosanoids in inflammatory and fibrotic processes, these results suggest that the alteration of AM eicosanoid production as a result of the inhalation of coal mine dust may be an important factor in the pathophysiology of coal workers' pneumoconiosis.The authors are grateful to Joan Greenwood and Barbara Scheetz for their excellent technical assistance and to Brenda Pavone for the preparation of the manuscript. This research was supported by the U.S. Department of The Interior's Mineral Institute Program administered through the Generic Mineral Technology Center for Respirable Dust under grant 1135142.Request for reprints should be sent to Douglas C. Kuhn, Ph.D., Department of Pathology, The M.S. Hershey Medical Center, Hershey, PA 17033.INTRODUCTIONPulmonary alveolar macrophages (AM) are activated by foreign particles and microorganisms that enter the small airways (Kass et al., 1966; Herscowitz, 1985). This defensive reaction involves phagocytosis, lysosomal enzyme release, and the generation of reactive oxygen species by the AM (Snella, 1986; Rich et al., 1987). A number of agents, including phorbol esters, zymosan, adenosine diphosphate, organic hydroperoxides, and calcium ionophore, have been shown to activate the AM in vitro (Badger, 1986; Marshall and Lands, 1986; Snella, 1986). The AM response to these activators appears to be mediated in part by the oxygenated metabolites of arachidonic acid (AA) (Bertram et al., 1988; Demers et al., 1987; Mcleish et al., 1987).The AM may metabolize AA through cyclooxygenase- and lipoxygenase- catalyzed pathways to produce a variety of eicosanoids including prostaglandin (PG) E2, thromboxane (Tx) A2, leukotriene (LT) B4, LTC4, LTD4, and several hydroxyeicosatetraenoic acid derivatives (HETEs) (Willis, 1970; Camp et al., 1983; Poubelle et al., 1986). The production of these eicosanoids may enhance the. defensive ability of the challenged lung since they stimulate chemotactic cell recruitment to the site of invasion, enhance extravasation of circulating immune cells, and promote local vasodilatation. However, continued stimulation of the AM population, with the consequent production of proinflammatory eicosanoids, may ultimately enhance the disease process by contributing to chronic bronchoconstriction, fibrosis, and the persistent release of toxic oxygen species."

Jan 1, 1990

By R. M. Winslow

"The phosphorus content of an iron ore is a determining factor as regards the value of the ore and also its metallurgical treatment. If some method of treatment, such as concentration, leaching, etc., could be used and the phosphorus con- tent of the ore reduced, it would be an important advancement in the iron mining industry towards the utilization of high phosphorus ores. Large bodies of material toe high in phosphorus to be marketable under present conditions would be made available, and a great deal of ore from the Cuyuna Range and other places, which is relatively high in phosphorus but otherwise suitable for making spiegel, could be reduced in phosphorus content sufficiently to permit its use in furnaces producing speigel.The form in which phosphorus occurs in iron ore is a much disputed question and it probably varies with the type and location of the ore. The statement has been made that ore piles on long exposure to the atmosphere often decrease in their phosphorus content. (Emmons, S.F. - Ore deposits, 1913, p. 652; Leith, C.K., Mesabi iron bearing district, U.S.G.S. Monograph 43, 1903, p. 275) There is described below experiments on the leaching of iron ores high in phosphorus, to determine whether it was economically possible to reduce the phosphorus content appreciably by leaching. As the research had a practical as well as a theoretical application, only low concentration of acids and alkalies were used.A number of variables were tried, among these being: (1) The solvent used, (2) strength of the solvent, (3) volume of solution used, (4) time ore was agitated (5) type of ore, and (6) screen size of the ore. The amount of ore taken was kept constant."

Jul 1, 1921

By E. H. Denny

A most interesting safety record has been made by the Colorado Fuel and Iron Co. s. Robinson ho. 1 mine located at Walsen, Cola. Mr. J. L. McBrayer has been superintendent of the Robinson No. 1 and 2 mines for the past 2 1/2 years, and Mr. David Muir has been foreman of the Robinson No. 1 mine since June, 1913. The last fatal accident at Robinson No. 1 mine occurred on July 27, 1915, and the tonnage produced at this mine since July 28, 1915, has been as follows:.

Jan 1, 1929

By Matthew J. DeMarco, Anthony T. Iannacchione

Coal bumps have presented serious mining problems in the U.S. throughout the 20th Century. Fatalities and injuries have resulted when these destructive events occur at the working face. Persistent bump problems can result in abandonment of large reserves or lead to premature mine closure. Through the years, alternative techniques such as artificial supports, extraction sequencing, destressing, pillar design changes and specific pillar retreat practices have been successfully implemented to mitigate coal mine bumps. Several techniques have evolved for room-and-pillar operations that control the way the roof rock breaks, regulating the manner in which stresses are redistributed in the mined section. Special mine layouts employed in longwall mines have also proved to be successful in safely redistributing or containing excessive loadings. However, with ever increasing production rates, greater overburdens and new mining systems, the need to evolve even more effective bump control designs will continue to challenge the U. S. coal mine industry.