Search Documents

By W. E. Lamont

The Bureau of Mines conducted flotation tests on a mixture of barite waste materials from Nevada in which essentially all of the barite values were finer than 20 micrometers. Flotation variables investigated in these tests were the effects of (1) sodium silicate as a pulp dispersant, (2) sodium hydroxide as a pH modifier, (3) increased amounts of sodium cetyl sulfate, (4) conditioning time and (5) solids content during conditioning. The optimum flotation conditions were achieved by adding 2.5 pounds of sodium silicate and 10 pounds of sodium cetyl sulfate per ton of feed and conditioning the pulp for 20 minutes at a 35-percent solids content. Using these conditions, a concentrate was produced that contained 94.7 percent BaS04, with an attendant recovery of 90.9 percent of the barite in the feed. In addition to the flotation tests, a selective barite flocculation process was developed to treat extremely fine barite. A barite concentrate containing 96.5 percent BaS04 with an attendant recovery of 82.1 percent of the barite was produced by selective flocculation. A process patent application has been filed based on this process.

Jan 1, 1982

By Edward E. Tate

This is a report on the design, development, and manufacture of a prototype roof bolting machine for high rise applications. The machine is designed to traverse a 32 inch entry and rebolt a roof fall area to a height of 28 feet 10 inches. Covered in the report is a chronology of the project, an explanation of the design problems, and a description of their solutions. The report concludes that the equipment as designed is suitable for the purpose intended and further testing is recommended.

Jan 1, 1981

By Maria I. De Rosa

Table 55 and figure 19 show the number of fires and fire injuries for stone mills by state during 1990-2001. Table 55 also shows the injury risk rates, employees' working hours, and lost workdays. In all, 118 fires occurred in 33 states. Seventy-six of the fires caused 82 injuries (including 8 fires and 6 injuries involving contractors). The yearly average was 9.8 fires and 6.8 injuries. The Ewhr value was 873 x 106 hr (In = 0.019), and the LWD value was 1,911. Missouri had the most fires (16 fires and 9 injuries), followed by Pennsylvania (15 fires and 14 injuries), Michigan (9 fires and 5 injuries), and Virginia (7 fires and 5 injuries). Of these states, Virginia had the highest injury risk rate value (In = 0.09 1). Table 56, partly illustrated in figure 20, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires and fire injuries decreased during most of the periods, with a sharp increase during the last period. The number of employees' working hours increased throughout the periods. The In values follow patterns similar to those shown by the injury values. Tables 57-63 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 21 shows the major variables related to fires for 1990-2001. Table 63 shows the fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By Leonard Obert

[Tng occasional. rock noises in a nice caured by brc,*ing and ripping of the back, settling, and other cailscr, are well-known tc~ a11 mining en- gineers. These noises oftcn prececte certnin tpes of rock failure as such are used to e certain ev';ent a; w:,rnlngs. Senides t5ese audible rock noisee t'nere are, l?o\;evpr, even Iprger nw.iber of' s;Lba.J^;li5le rock mis~s, which must; be piclcell UT with sole type of vi-urr,tion rnicroyhoce and qli- fied in order tnnt :hey n;ny e heard. It v:zs s~v;,yestec" Ir, an evlier ? ,I a.ldible noises Ifureau of I.lines s~zb:ic;et.iod that n stud:r of t!ler;c! *- t mig!!t be useful ir. de temining roc^ movemrnt 3 preceding failure.]

Jan 1, 1941

By Leonard Obert

[Tng occasional. rock noises in a nice caured by brc,*ing and ripping of the back, settling, and other cailscr, are well-known tc~ a11 mining en- gineers. These noises oftcn prececte certnin tpes of rock failure as such are used to e certain event a; w:,rnlngs. Senides t5ese audible rock noisee t'nere are, l?o\;evpr, even Iprger nw.iber of' s;Lba.J^;li5le rock mis~s, which must; be piclcell UT with sole type of vi-urr,tion rnicroyhoce and qli- fied in order tnnt :hey n;ny e heard. It v:zs s~v;,yestec" Ir, an evlier ? ,I a.ldible noises Ifureau of I.lines s~zb:ic;et.iod that n stud:r of t!ler;c! *- t mig!!t be useful ir. de temining roc^ movemrnt 3 preceding failure.]

Jan 1, 1941

By T. Christos

The explosive oils, nitroglycerin (NG) and ethylene glycol dinitrate (EGDN), were extracted from dynamites by a halocarbon solvent and were then determined by high-pressure liquid chromatography. Separation was achieved by liquid-liquid chromatography on a column packed with Durapak-Carbowax 400/Corasil II and the eluted NG and EGDN were detected with a double-beam ultraviolet detector.

Jan 1, 1973

By Homer J. Ballinger

A multiple drill carriage or "jumbo," which is believed to be unique in both design and performance, was constructed and has been in use for the past year at the Bureau of Mines experimental oil-shale mine near Rifle, Colo. This jumbo mounts four long feed percussion drills and is so designed that two men can operate all four drills. Before the jumbo was placed in operation, a minimum of eight man-shifts was required to drill 72 fifteen-foot holes in headings 60 feet wide and 27 feet high. The sane round is now drilled by two men in about 6 hours. Over 500 feet of drilling per man shift is easily and consistently accomplished. Use of the jumbo has resulted in a 75 percent reduction in drilling labor and a substantially lower drilling cost.

Jan 1, 1950

By Lippe D. Sadwin

This report describes a high-speed streak camera technique for measuring the lateral shock pressure generated by a cylindrical explosive charge detonated from one end. Experimental data show that the magnitude of the lateral pressure is approximately 50 percent that of the pressure generated from the terminal end of the charge for three explosives studied.

Jan 1, 1965

By M. O. Renwick, Paul Zinner

"INTRODUCTION In September 1943, the Bureau of Mines conducted a limited program of churn drilling on the Winskell property in the Shullsburg area of Lafayette County, Wis. The work was undertaken as part of a general investigation by the Bureau of the zinc-producing area of southwestern Wisconsin at a time when special effort war being made to increase the production of metals necessary for the war program.Drilling described supplemented a previous drilling program conducted by the Vinegar Hill Zinc Co. The results of both programs encouraged subsequent investigation by the Cuba Mining Co. and eventual development of the Andrews mine.ACKNOWLEDGEMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by such project as soon as praticable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the investigative work, and prepares the final report."

Aug 1, 1947

By J. T. McCartney

Thin sections of coal have been prepared for many years either by cutting on a microtome (1,2)5 or by grinding and polishing (2,1). Specimens of most coals had to be demineralized in hydrofluoric acid and softened in caustic solutions before they could be successfully cut with a conventional microtome. Some lignites could be cut without pretreatment. Jeffrey (1) obtained sections from coals of all ranks, although long and tedious pretreatment was required for anthracite. His sections were less than 1 cm.2 in area (probably much less for high rank coals) and about 5 microns thick. Thiessen (2) also cut sections of softened coals, mostly of low rank. His sections were a few square millimeters in area and about 3 microns thick. However, Thiessen preferred ground and polished sections for detailed studies because they were larger and had not been chemically attacked by softening media. He prepared ground sections as large as 4 cm.2 in area and usually 5 to 10 microns thick. Thousands of such sections, covering complete column samples of many coal beds, were studied for a number of years (4). With the development of the electron microscope and increased interest in quantitative optical studies of coals, a need for much thinner sections arose. However, no suitable technique for preparing such sections was known until Fernández-Morán developed a diamond knife for cutting ultrathin sections of hard materials (5). Workers at the Centre d'Etudes et Recherches de Charbonnages de France applied this new tool to the cutting of coal sections and have recently described their technique to the Burg, of Mines. Using their methods, with some modifications, researchers of the Bureau of Mines have succeeded in cutting ultrathin sections of coals ranging in rank from lignite to

Jan 1, 1961

By J. H. Perry, Joseph Cervik, G. N. Aul

The Bureau of Mines is conducting research to determine the effectiveness of long holes in degasifying an area of the Upper Split of the Lower Sunnyside coalbed at Kaiser Steel CO.'s Sunnyside No. 1 mine. These holes were drilled from the two outside entries of a section that was closed to mining because of excessive methane emissions. Two holes drilled to 430 and 450 feet produced initial gas flows of 160,000 and 127,000 cfd, respectively. Sixteen days after the completion of the second hole, the total gas production declined to just over 144,000 cfd. In 9 months of degasification, over 35 MMcf of commercial-quality gas has been removed from the coalbed. The combined gas flows declined to 106,000 cfd in the 9-month period. The two holes have reduced face emissions by about 40 pct.

Jan 1, 1978

By R. V. Ramani, R. Bhaskar

"One of the primary means of control of health hazards from respirable contaminants in mine atmospheres is through design and operation of mines to meet mine health and safety regulations and recommended practices. A U.S. National Academy of Sciences study concluded that for significant progress in coal mine dust control, research should be directed more toward obtaining fundamental understanding of the origin, transport and characteristics of respirable coal mine dust. Theoretical and experimental studies on transport of dust · in mine airways, particularly coordinated efforts to validate theory with practice, are scarce. Some empirical models, developed on the basis of experimental data, are available but these models cannot be applied to new conditions. The purpose of this paper is to present the results of theoretical and experimental studies on the transport and deposition of dust in mine airways. This study is a part of an ongoing research project in the Generic Mineral Technology Center on Respirable Dust.In the paper, the assumptions of the modeling phase of the project and the development of a convectiondiffusion equation for dust transport in mine airways are outlined. The important aspect of the modeling effort is the capture of the deposition phenomenon. The experiments performed under controlled conditions in a typical mine airway, as well as under normal mine operating conditions, are discussed. The comparison of the model predictions with experimental results are made to identify critical areas of agreements and deviations. The implications of the findings and areas for further research and development are presented."

Jan 1, 1990

By S. B. Levin

"INTRODUCTION An exposure of large beryl crystals in pegmatite on Beryl Mountain, in Sullivan County, N. H., was the basis for investigation by the Bureau of Mines to determine the extent of the beryl mineralization and to expose other parts of the same zone that were favorable for additional beryl-rich shoots. Testing by surface cuts, trenching, and tunneling was conducted by the Bureau of Mines from August to December 1943.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to the national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyzes samples and makes beneficiation tests. The field work was supervised by Paul M. Tyler, regional engineer, and John D. Bardill, district engineer. S. B, Levin was in direct charge of the project.LOCATION AND ACCESSIBILITYThe deposit is on the northeast slope of Beryl Mountain, 1 mile south of the village of South Acworth. The village, on State Highways 101 and 123a, is 12 miles northeast of Bellows Falls, Vt. The deposit is reached from South Acworth over a gravel-surfaced road and about 1,000 feet of good truck trail (fig. 1).The nearest railroad siding is at Cold River, on the Boston & Maine Railroad, where there is also a fairly modern, but now idle, feldspar mill."

Mar 1, 1948

By A. Wahab Khair

"Geologic materials emit transient noises when stressed /1/. The rate and pattern of these transient noises or acoustic emissions (A.E. hereafter) depend on the stages of deformation of the material /2/. It has been demonstrated that rock/coal fracture processes under stress consist of three distinctive stages--crack initiation, propagation and ultimate fracture--and that coalescence of numerous cracks leads to ultimate failure rather than the propagation of a single crack /2,3/. This paper presents an analysis of fracture formation in rock/coal specimens subjected to straight wedge indentors using A.E. technique.The effect of specimen geometry, wedge indentor angle, confining pressure, and material anisotropy on fracture type (tension, extension, and shear crack), fracture length, and fracture intensity were studied. Two types of material mainly Berea sandstone and Coal Berg No. 2 coal were used in this study. Prior to the experiment the mechanical properties of both sandstone and coal were determined using rectangular specimen (Figures 1 a) in standard compression tests and are given in Table 1. In this study cylindrical and rectangular specimens were first prepared to proper dimensions of 2 in. x 1.5 in. and 3 in. x 1.5 in. x 1.5 in. (5.08 cm x 3.81 cm and 7.62 cm x 3.81 cm x 3.81 cm), respectively and then instrumented with SR-4 strain gages as shown in Figure 1. The instrumented specimens were then tested under four distinct load boundary conditions as illustrated in Figure 2. During a typical experiment the instrumented specimen was placed in a specially designed loading jig (Figure 3) where a predetermined lateral pressure was applied mechanically to the specimen by adjusting the inner plate of the confining chamber via screw while monitoring strains in the specimen. Using rock/coal elastic constants and measured strains, a predeter¬mined lateral pressure was applied to the specimen. Then a vertical load was applied by the straight edge of a wedge indentor attached to the upper platen of the universal loading machine via ball and socket arrangement (Figure 4). The arrangement allowed uniform application of load in a straight line manner on the surface of the specimen. During the test a number of parameters namely strains, load and A.E. rates were recorded (Figures 5a-b)."

Jun 1, 1988

By Charles T. Chislaghi

An economical, remotely operated (automated), temporary roof support (ATRS) has been developed by the Bureau of Mines for use on a single, fixed-head roof-bolting machine (squirmer) that operates in low coal seams (less than 42 in thick). The ATRS eliminates the need for squirmer operators and helpers to go under unsupported roof to set or remove temporary support prior to or during the roof-bolting cycle--a task that annually accounts for approximately 20 pct of all roof fall fatalities. The ATRS can be adapted to any squirmer used in the U.S. low coal fields. A prototype ATRS was field-tested at Imperial Colliery Co.?s Mine No. 20 in Eskdale, W. Va. The Mine No. 20 amended roof- control plan, which requires the use of the Bureau?s ATRS as temporary support during face bolting, has been approved by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor.

Jan 1, 1982

By BUREAU OF MINES

Atentative Draft of a standard smoke abatement ordinance has been prepared by a joint committee made up of representatives of the American Society of Heating and Ventilating Engineers, the Stoler Mamufacturers Association, the American Civic association, and the Fuels Division of the American Society of Mechanical Engineers. The Committee is desirous of obtaining helpful criticism and suggestions about this ordinance, which should be mailed to the chairman, Dr. O. P. Hooi, Bureau of lines, ashington, D. C. Te personnel of the committee is as follows: Dr. O. P. Hood, chairman, and Henry Kreisinger, representing the Fuels Division of the American Society of Mechanical Engineers; P. J. Dougherty, representing the American Society of Heating and Ventilating Engineers; Lloyd R. Stowe, representing the Stoker Mam- facturers Association; Everett L. Hillard, representing the American Civic Ascociation; and Osborn Monnett and Harry 3. Meller, members at large.

Mar 1, 1930

By Thomas C. Miller, Charles E. Mongan

"This publication is a progress report on Bureau of Mines studies in applying sonar techniques to roof-control problems in coal mines. Preliminary tests in the laboratory were made on layers of roof rock. To apply the experience thus obtained, a unit was designed and constructed and was used underground.The term ""sonar technique"" refers to the system of generating a beam of sound waves, shaping and directing the beam, introducing the beam into a medium to be studied, and examining any returning waves with a view of inferring the nature of the material traversed by the waves and the presence of interfaces or obstacles in the medium.The theory and actual underground experiments indicate that the sonic method is feasible. Information from physical tests made in the Bureau's Experimental mine confirmed the validity and potential usefulness of the sonar method. Lighter and more compact apparatus is desirable, and permissible equipment suitable for use in gassy or dusty mines must be developed. However, no particular difficulties are anticipated; consequently, this scientific approach to the exploration of roof strata shows definite promise. INTRODUCTIONThe problem of roof control in the coal-mining industry is of major importance. More than 50 percent of all coal-mine fatalities and 25 percent of all nonfatal serious injuries are caused by falls of roof, face, or ribs. The Bureau estimates that more than $128 million was spent by the coal-mining industry in 1958 for supporting roof."

Feb 1, 1960

"Reports are sometimes heard of one ill effects of pneumatic tools on the hands of workmen. In consequence of such reports, Dr. Francis M. Barnes, Jr., M..D. of St. Louis, Missouri, was retained by the operators to make an investigation of conditions in the Bedford, Indiana, region, and the result of this investigation was published the Journal of the Missouri State Medical Association, Volume 16, February 1919. A brief review of this report may be of interest to all users of pneumatic tools, or operators of plants where such tools are employed.The investigation was made during December 1917, and involved an examination of general working conditions, and a careful physical examination of stoneworkers who had long used pneumatic tools. As the Bedford district is the most important structural limestone producing center in the country, the results of this investigation may be regarded as fairly conclusive as to the general effect of pneumatic tools on limestone workers."

Jan 1, 1920

During 1999, there were six fatalities in surface mines involving haulage equipment colliding with a smaller vehicle or person, or backing over the edge of a dump point. All of these fatalities can be attributed to the extensive blind areas around large haulage equipment. Researchers at NIOSH are investigating various technologies that can be used to monitor these blind areas and provide information on nearby obstacles to an operator. So far, the technologies listed below have been tested on dump trucks used in surface mining. The selection of these systems was based on their ability to handle the tough environmental conditions found in mining operations and how well they detected obstacles out to 40 or 50 feet beyond the rear of large dump trucks. Some of the manufacturers of available collision warning and camera systems are also listed.

Jan 1, 2001

By Van E. Shaw

Fusion of an 86-percent euxenite concentrate with ammonium sulfate was investigated by the Bureau of Mines. Reaction for 4 hours at 400° C results in conversion of both the rare-earth elements and the titanium-columbium components to water-soluble compounds. Similar results are obtained with ammonium bisulfate. Stirring the fusion mass decreases the reaction time substantially. Alternatively, treating the fusion product with a 3-hour, 650° C calcining step renders the non-rare-earth constituents insoluble, thereby allowing selective leaching of a pure rare-earth fraction with an overall yield of 97 percent.

Jan 1, 1967