Search Documents

By Mark I. Copeland

The Bureau of Mines discovered that silicon and nickel additions can prevent the formation of copper alloys of Sn, Sb, and As on the surface of steel during reheating to hot-working temperatures. When molten, these copper alloys cause surface hot shortness during hot working. Wrought steels were reheated isothermally and by simulated industrial practice; the resulting surfaces were metallographically evaluated. The steels contained, In weight-percent, 0.20 C, 0.45 Mn, and up to 1.00 Si, 1.00 Cu, and 0.15 Ni, and up to 0.30 Sn, Sb, or As. The larger the Cu, Sn, Sb and As content of the steels, the greater the amount of silicon necessary to prevent copper alloy formation. A content of 0.10 Ni considerably decreased the amount of silicon necessary for copper steels containing tin and antimony, but not for those containing arsenic. Theories for the beneficial effect of silicon and nickel additions are presented.

Jan 1, 1975

By Ronald D. Hill, Elmore C. Grim

Some of the terms defined here are not used in the text. However, the terms will be useful to those interested in this and other publications in the field of coal surface mining.

Jan 1, 1974

By C. D. Litton

Submicrometer particle concentrations and average particle sizes were monitored for four full-scale sealed coal fires in the multiple-entry section of the Bruceton Experimental Mine. The data from these tests indicate that there exists a very good correlation between the submicrometer particle concentrations and the maximum temperatures measured within the coalbed. As the maximum coalbed temperature decreases with time after sealing, the submicrometer particle concentrations show a corresponding reduction. This particle-temperature correlation is in sharp contrast to the gas concentration data obtained, for which essentially no correlation exists with the measured coal-bed temperatures. The results of these full-scale tests indicate that the measurement of submicrometer particle concentrations may be a more realistic approach to determining the status of underground sealed fire areas.

Jan 1, 1981

By Gregory P. Cole, Jeffrey Shawn Peterson

The Pittsburgh Research center3 conducted research to study and improve electrical fault detection on coal mine direct-current (dc) trolley systems. A suspended trolley line delivers power at voltages of 300 or 600 V dc to the haulage equipment and other loads. Roof falls or other accidents may force the trolley line down so that an electrical fault current may flow between the trolley line and rail. This fault current could result in localized heating, arcing, and perhaps fire. Such faults are not always preventable by the existing circuit protection because the current magnitude is well below typical operating levels of the trolley system. The research discussed in this report studies the applicability of computerized signal analysis techniques to solve this problem. Tests were conducted at cooperating coal mines. Measurements were taken during normal loading of the trolley system (light, intermediate, and heavy traffic), during induced fault conditions (arcing and bolted faults), and during transitions between the two. These data were then used to train and test a microprocessor-based fault detection algorithm. Later, field tests of the detection algorithm found that it correctly classified the state of the trolley system greater than 95% of the time.

Jan 1, 1997

By John Jordan, Steven J. Knoll, Douglas Tesarik, Theodore J. Williams, David K. Denton, Douglas F. Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because this condition can result in failures of ground that lead to both injuries and death. Personnel from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health studied two methods for identifying stress in rock. A seismic tomographic survey, finite-difference analysis, laboratory measurements of compression wave (ultrasonic) velocities in rock cores, and site geology were integrated to evaluate the use of seismic tomography for identifying induced pressures in an underground pillar at the Edgar Mine, Idaho Springs, CO. Electromagnetic (EM) emissions were also investigated in the Galena Mine, a deep underground mine in Idaho, in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results of this research indicated that (1) seismic tomography appears to be a useful tool for determining relative stress in underground pillars, while (2) EM emissions do not appear to be significant precursors of impending catastrophic ground failure.

Jan 1, 2004

By Samuel P. Harteis, Eric S. Weiss

The National Mining Association and the Mine Safety and Health Administration requested that the National Institute for Occupational Safety and Health (NIOSH) conduct full-scale evaluations of a recently developed carbon fiber-reinforced polymer (CFRP) reinforcement technique for upgrading existing mine ventilation seals to withstand an explosion pressure of 50 psi or greater. The evaluation was conducted in the NIOSH Pittsburgh Research Laboratory’s Lake Lynn Experimental Mine (LLEM) near Fairchance, PA. The purpose of the evaluation was to determine the blast resistance of the CFRP reinforcement technique, designed to increase the strength of two types of existing 20-psi-rated in situ mine ventilation seals. Two candidate ventilation seals were selected to represent the 20-psi alternative seal designs typical of those used in mines prior to July 2006. Installed within the LLEM were (1) a 4-ft-thick pumpable cementitious foam seal using material with a designed 150- to 200-psi average compressive strength at 28 days and (2) a 24-in-thick, low-density cementitious block seal with a center pilaster and keyed to the floor and ribs. The materials necessary for the CFRP reinforcement technique were then installed on the outby (active) side of each seal, and the seals were subjected to explosion overpressures. Both seals with the CFRP reinforcement retrofit successfully withstood explosion pressures of 60 psi or greater during the full-scale evaluations in the LLEM.

Jan 1, 2008

Large quantities of combustible materials are often found in underground metal and nonmetal mines, with support timber predominating. Wood lagging and timber, wires and cables, brattice cloth, hose, paper products, cardboard cartons, and wooden containers are additional combustible materials commonly found in underground storage areas. Shorted or overloaded electrical cables, worn sockets and plugs, spontaneous combustion, careless smoking, and welding and cutting are common fire ignition sources. Inexpensive, reliable fire detection and suppression systems are available to provide early warning and to extinguish fires that originate in underground storage areas.

Jan 1, 2011

By Charles L. Kusik

As part of an effort to establish processes that could be exploited in case of adverse changes in international chromium production and trading patterns, this study was sponsored by the Federal Emergency Management Agency (formerly the Federal Preparedness Agency) through the Bureau of Mines, to experimentally determine the feasibility of recovering chromium from critical scrap metals containing significant quantities of this element. Based on a conceptual pyrometallurgical chromium recovery flowsheet developed at Arthur D. Little, Inc., the experimental program described in this report demonstrated key process steps for the recovery of chromium as ferrochromium in a batch process. The process involves oxidation of chromium into a slag phase, subsequent separation of the slag phase from the remaining metal, followed by reduction of chromium from the slag phase to produce ferrochromium.

Jan 1, 1981

By Martin Hertzberg

The Bureau of Mines 8-liter flammability system was used to study the effectiveness of a variety of powdered inhibitors in preventing the propagation of explosions of coal dust or methane in air. Over 35 different chemical additives were evaluated against Pittsburgh seam pulverized coal. The least effective inhibitors were the carbonates, which required mass additions in the range of two to three parts inhibitor to one part of coal dust in order to prevent propagation. The most effective inhibitors were the derivatives of ammonium phosphate, which were effective quenching agents at additions of only one part inhibitor to four parts of coal dust. Alkali halide powders were of intermediate effectiveness. These laboratory-scale results are in good agreement with full-scale mine experiments in all cases where detailed comparisons have been made. Data were also obtained for the effectiveness of several of the same powdered inhibitors against methane-air explosions. Their relative order of effectiveness and the concentration ranges required for quenching the gas explosion are comparable to those measured for coal dust explosions. Data are also presented for the effectiveness of N2 and CF3Br addition. Some preliminary data are also presented for powder addition to methane burner flames. Those data are compared with other burner data and evaluated in terms of their relevance to explosion tests.

Jan 1, 1982

By E. Chin

The mineral industry of Bangladesh was totally dominated by natural gas production and its downstream uses. A small amount of cement was produced, and clays were used locally for ceramics and construction materials. Nitrogenous fertilizer was produced from natural gas and a modest, scrap-based steel industry produced steel for local consumption. The country has been developing and using its abundant and inexpensive gas reserves as fast as practical. The population, however, was predominantly dependent on agriculture for its livelihood. The industrial sector accounted for 10% of the economy, and most of the industrial output was directly associated with agricultural products jute, tobacco, and textiles. Industrial expansion, even with the availability of gas, was severely constrained because of limited domestic demand, lack of skilled work force and management, poor infrastructure, and a low rate of domestic savings. To put greater emphasis on the industrial sector, the Government established a National Committee for Industrial Development in July. The Committee instituted policy reforms in the areas of trade and investment. One important step was to move from a positive import list to a negative list, thereby permitting imports of items not restricted or banned. The system for recovering and approving new domestic or foreign industrial investments was streamlined to expedite what had become a cumbersome, bureaucratic exercise. To encourage industrial development in areas away from the crowded urban centers, several economic incentives reportedly were adopted. These included a reduced tax rate on imported machinery, exemption of import license fees, a reasonable debt equity rate, and a 9-year income tax exemption period.2 In the trade sector, imports increased 12% in fiscal year (FY) 19843 mainly

Jan 1, 1987

By C. E. Jordan

Under its program of advancing minerals technology, the Federal Bureau of Mines has invented a laboratory apparatus for continuous separation of minerals based on differences in dielectric properties. The separator consists of a rotating drum electrode and a wire screen electrode positioned 3 mm apart. A high voltage applied across the electrodes that are immersed in a dielectric fluid produces a high-gradient electric field. The high-dielectric-constant (K) minerals are attracted to and conveyed through the separator by the rotating drum electrode, while the low K minerals settle through the screen electrode. Several design and operating parameters, such as electrode configurations, the dielectric liquid and its dielectric constant, electrical voltage and frequencies, feed rates, and particle sizes were studied. In addition, 28 different mineral mixtures were tested with the dielectric separator. In typical tests, a sample of rutile and quartz gangue containing 10-percent rutile was concentrated to 62-percent rutile with 94-percent rutile recovery. A second-stage dielectric separation of the rutile concentrate produced a 92-percent-rutile concentrate. The overall rutile recovery for the two-stage dielectric separation was 86 percent.

Jan 1, 1980

By R. L. Anderson

Mechanical cleaning of bituminous coal in the United States was begun about 1875, with plants in western Pennsylvania and Illinois. The United States Geological Survey began to record the quantity of washed bituminous coal in 1906; and the series was carried forward to 1923, except that no data were collected, for 1922. This statistical work was transferred to the Bureau of Mines in 1925, and the collection of data on mechanical cleaning was resumed in 1927. Data collected before 1927 include only the coal that was washed at the mines and do not include that cleaned by pneumatic methods at the mines and that cleaned at central washeries operated by consumers.2/ The total bituminous coal washed in 1906 was less than 10 million net tons. In 1927, the first year for which complete figures are available for all types of mechanical cleaning, 28 million net tons of bituminous coal were cleaned in the United States.

Jan 1, 1951

By W. J. Pena, C. W. Owings

"Generally, the hazard of cool-dust explosions in tipples and cleaning plants is not given the consideration that is given it underground. This lack of consideration is probably due to failure to appreciate the potential hazard. An explosion in a tipple or cleaning plant is basically little or no different from an explosion underground. If bituminous-coal dust is raised into a cloud in the air and comes in contact with arcs from motor brushes, switches, or open flame, the dust is very likely to ignite, and flame will very probably propagate or extend through it if the quantity of dust per unit of air space is sufficient. The open space in a tipple or cleaning plant may reduce the violence of the explosion, but it is not likely to prevent ignition or propagation of flame.The movement of coal through a tipple or cleaning plant naturally puts into suspension a large amount of dust, which finally settles on exposed surfaces. Any disturbance that will put this dust into suspension in a sense enough cloud can result in the dust being ignited by an arc or open flame if one should be present. An explosion of bituminous-coal dust in a tipple or cleaning plant generally can be prevented either by keeping it thoroughly clean or by removing all sources of ignition, or both.The tests at the U.S. Bureau of Mines Experimental mine have shown that the explosibility of coal dust is proportional (other things being equal) to the ratio of the volatile matter to the volatile matter plus the fixed carbon, indicated thus:The volatile ratio for the Pittsburgh coal bed is calculated as follows:Therefore, as the volatile matter decreases the liklihood of ignition decreases; however, coal-dust explosibility depends on other factors also, such as fineness, dryness, and cloud density; and under some conditions other factors also intervene.Proof of the explosibility of coal dust in the absence of explosive gas has been shown in numerous cases in mines and mine plants and also by a series of tests. In these tests a dense cloud of dust is blown onto an open flame or an electric arc, almost invariably with resultant exploding of the dust. The Safety Division of the United States Bureau of Mines has made a number of demonstrations of the explosibility of Pittsburgh coal-bed dust, using a small gallery or box in which a cloud of coal dust is blown onto a lighted match; larger-scale tests have been made with an electric arc as the igniting agent. Bituminous-coal dust is readily ignited with a medium arc, but with low-volatile coals a larger arc is required. For test purposes, a 100-ampere arc has been used. Ignition has occurred readily under these conditions with Pocahontas No. 5 coal dust with ratios of volatile to total combustible of 0.232 to 0.253, and with Pocahontas No. 3 coal dust with a combustible ratio of 0.242. Lower Kittanning coal dust, with a ratio of 0.187, did not give definite ignitions, and Pocahontas No. 4 dust did not explode, although part of the coal-dust cloud ignited. It is probable that even the low-volatile coal dust will be found to be explosive with a higher-amperage electric arc as the initiating agent."

Jul 1, 1936

By D. Harrington

"Since its establishment in 1910 the Bureau of Mines has consistently recommended the rock-dusting of bituminous and lignitic coal mines as a preventive of widespread explosions. As with many other proposed innovations, the response to the bureau's recommendation has been slow; but during the past 10 years many coal mines have done some rock-dusting, even though probably fewer than 50 of the country's approximately 6,000 coal mines are thoroughly rock-dusted. Notwithstanding the inadequacy of the rock-dusting which has been done in most of the mines which have adopted the new system, numerous cases are at hand. indicating the well-founded basis of the bureau's claims regarding the effectiveness of rock-dust in stopping explosions. Very brief descriptions will be given of several cases in which explosions in coal mines of the United States are fairly definitely known to have been stopped by rock-dust during the past 5 or 6 years; in addition, several cases are cited in which explosions were stopped through the agency of rock-dust and moisture.A rock-dusted mine is one in which the floor, roof, and sides of every accessible working place, including haulage ways, airways, manways, and rooms and connections have an application of rock-dust - for instance, limestone - such that the incombustible content of the aggregate dust on those surfaces is over 60 per cent. The dust in these workings should be sampled at regular intervals to determine whether the incombustible matter in the coal-dust is less than the necessary minimum of 60 per cent; another application of rock-dust should be given when the incombustible percentage is less than 60. (As an example of thorough rock-dusting, see Bureau of Mines Information Circular 6578, 1932, which describes how rock-dusting is done in Alabama at a cost of 1.8 cents per ton of coal for a thorough application; Report of Investigations 3060, February, 1931, Rock-Dusting In A Pennsylvania Coal Mine; or Information Circular 6244, 1930, giving data, including costs, on rock-dusting in coal mines in New Mexico.)An explosion may be started by the ignition of gas, even when rock-dust is present; hence it is not correct to say that rock-dust will prevent an explosion of gas; however, if rock-dust has been applied to a working place which has present an explosive mixture of me-thane and air, and if an open light is used or a blown-out shot or an electric arc occurs, although there will very likely be an ignition and possibly an explosion, the rock-dust will certainly prevent ignition of the coal-dust nearby, and unless the general atmosphere has an explosive gas mixture, the rock-dust will stop propagation of the flame throughout the mine. In other words, if an explosion is started by gas or by coal-dust and the mine has been rock-dusted as defined, the rock-dust will prevent widespread extension of the explosion, unless the general atmosphere contains methane and air in explosive proportions.With these definitions clearly in mind, instances are now given where rock-dust has played a prominent part in the stopping of several explosions. No cases have been included where there was any reasonable doubt that rock-dust had taken a definite part in the limiting of the explosions."

Apr 1, 1932

By E. H. Denny

"Reduction of mine accidents appears to depend upon essentially the same fundamentals, whether considered from the viewpoint of the mine operator, miner, State mine inspector, or safety engineer. Conditions of mine operation with respect to safety are governed in most States by a mining law, usually somewhat general in its provisions but more specific than laws dealing with other industries, Methods of mining development and practice evolved through experience have been handed down from generation to generation; many of these are intended to avoid injury to men and also loss of property. To carry out the intent of these bases of law and experience relating to safety supplemental measures and conditions are necessary. Among these may be: (1) Planned safety rules adapted to the mine and compliance by both officials and Miners with such of these rules as pertain to their work; (2) a supervisory force adequate and competent to ¬administer the mining laws and safety rules; (3) discipline adequate to secure compliance with safety measures; (4) safeguards against mechanical, electrical, falling, and other hazards; (5) mining operations planned with respect to safety of workers; (6) an active safety organization of officials and employees; (7) education of officials and employees in safety practices; and (8) an active sustained interest in safety by management and employees.This paper presents the viewpoint of the safety engineer, though a safety engineer connected with a specific mine or group of mines would be in a better position than the writer to present the industrial engineer's thought. The application of the mine safety fundamentals just outlined will be given consideration from observations of methods used by safety engineers and supervisors.The term ""safety engineer"" includes men of various duties, various degrees of experience, and various authority. Depending upon the size of the operation or the interest of the management in safety, the safety engineer may have accident prevention as his sole duty; he may be the head of a sizable safety organization; or he may be in part a claim agent; a statistician compiling figures for the enlightenment of the company, the public, or a mining institute meeting; a surveyor who must convince the miner that his scale of 10/10 equals 1 foot does not defraud the miner of 6 inches to every yard measured; or he may be by heaven¬ly gift an orator capable of assuring the employees that ""all's right with the world""; he may be a young engineer gaining, experience while checking the observance of company rules and investigating accidents; or he may have the physical ills frequently resulting from several decades of mining experience and instead of a pension, the position of safety engineer has fallen to his lot. He may have mine-operating authority to correct immediately a dangerous condition or practice or he may have his recommendations officially disregarded at the monthly meeting or when the bottom of the desk basket is reached. He is likely to find that his viewpoint on accident reduction is considered unsound today because of youth and inexperience and unsound later because of old age and senility. He is likely to find the easiest course to be that of attributing to Providence and the carelessness of the worker the mishaps that result in the removal of a man to the hospital or the morgue."

Dec 1, 1936

By F. W. Richard

This paper describing the mining practices at the Ground Hog Unit of the Asarco Mining Co., a subsidiary of the American Smelting and Refining Co., is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and costs in the various mining districts of the United Stated. The Ground Hog mine is at Vanadium in the Central mining district, Grant County, N. Mex., about 1.0 miles east of Silver City and 2 ½ miles southwest of Santa Rita. A branch line of the Atchison, Topeka & Santa Fe Railway connects Vanadium with Deming, about 45 miles southeast.

Jan 1, 1930

By G. L. Neumann

In October 1949 the College Park Branch of the Mining Division instituted a survey of the New England pegmatites. Many of the New England pegmatite deposits were superficially examined, and the Bumpus quarry in Albany, Oxford County, Maine (see fig. 1), was selected for a diamond-drill exploratory-development project to supply information for developing more economical mining methods and no increasing production of beryl and other scarce minerals associated with pegmatitic intrusives. The Bumpus quarry has been mined intermittently by three operators since it was opened in 1927. At the time of drilling, the vein or dike (see figs. 2 and 3) had been mined to a depth of 60 feet for a strike length of 280 feet. The dike averages 40 feet in thickness and dips 50 degrees southeast. The Bureau of Mines drilled seven diamond-drill holes between September 27 and November 27, 1950. These holes showed that the dike persists for at least 350 feet to the east and probably 200 foot to the west of the present excavation. The drilling also indicated that the dip, as exposed at the surface, continued unchanged at 500 to a depth of at least 50 foot below the pit. The dike was not delineated, although it fingered out as pegmatite interbanded with Granite, diorite, and gneiss in diamond-drill hole B-4, approximately 250 feet west of the pit. Further drilling will be necessary to find the extent of this pegmatite dike and to determine the safest and most economic mining system.

Jan 1, 1952

By C. M. McKinney

Sulfur content data from Bureau of Mines routine analyses of 1,060 United States crude oils were used with crude oil production data for the years 1956-66 to prepare tables and charts that illustrate the volume and percentage distribution according to sulfur content of crude oil produced in 10 geographical areas of the United States. Similar relationships for foreign crude oils based on analyses of 201 crude oils and production during 1966 are illustrated for Africa, Canada, Middle East, and South America. Tables are included giving field name, sulfur content, geologic name and age of producing formation, depth of producing formation, and production during 1966 for 882 United States crude oils and 201 .foreign crude oils. Between 1955 and 1966 the average sulfur content of crude oils produced in the United States decreased from 0.73 to 0.67 percent.

Jan 1, 1967

By W. L. Hunter

Eleven steelmaking heats are described in this Bureau of Mines report in which acid practice was used to produce carbon steel from pre reduced iron ore pellets. Furnace slags obtained with no flux addition to the charge became quite viscous as they cooled, which precluded pressure casting from a ladle. Lime was added to the furnace charge at two levels to eight of the heats to modify slag characteristics in the furnace, and to the ladle in two heats to further modify the ladle slag cover. Selected ingots from nine heats were successfully rolled on a commercial mill to produce No. 10 reinforcing bar.

Jan 1, 1974

By Charles L. Kimbell

In broadest overview, a substantial part of the world's mineral industry in 1990 registered small gains over its 1989 performance, but traditional statistical measures of mineral industry performance, namely global production, trade, and consumption levels, failed to mirror these gains. This was because of the sharp downturns in the mineral industry activity in the U.S.S.R. and the former centrally planned economy nations of eastern Europe. These downturns in this one geographic area had influences on almost all traditional statistical series, in some cases simply significantly reducing growth, in other cases providing for a global downturn, in almost all cases despite considerably brighter outlooks based on activities in other world areas. To be sure, the U.S.S.R. and eastern Europe were not the only places on the planet suffering problems of one type or another in 1990 that impacted on minerals industry activity, but with the acquisition of information presently available, it seemed almost assured that the difficulties of these economies in transition will be the most difficult of problems to resolve in the long run. It certainly appeared that the legacy of the half century or more of economic central planning will be a decade or more of very difficult adjustments, and a number of these will greatly affect not only the minerals industry of these transition countries, but also the rest of the globe's mineral industry as well.

Jan 1, 1993