Search Documents

Detect fires in or near mine shafts, isolate smoke filled areas, and remotely extinguish fire. Approach A system (of sensors, automatic alarms, an aboveground control console, remotely operated ventilation doors, and sprinklers) has been built from off the-shelf components, and fire, tested in two mines. How It Works The system uses three different kinds of sensors that can detect the heat or smoke of a fire and automatically actuate alarms. When the alarm sounds in the control center on the surface, water sprays in the mine shaft and shaft station areas can be remotely turned on to deluge both the inside and the outside of the mine shaft's wooden support structure. To protect miners from toxic fumes, smoke control doors can be closed or opened, either remotely from the control center or directly by miners using the manual or electrical actuators at the door locations. Man doors built into each ventilation door allow persons to pass without opening the main door.

Jan 1, 1977

By M. J. Ferrante

Relative enthalpies of cuprous iodide (CuI) were measured at the Bureau of Mines to provide thermodynamic data for the advancement of min-eral technology. Enthalpy measurements between 298.15 and 1,396.3 K were made with a copper-block drop calorimeter. The temperatures of transition were measured by differential scanning calorimetry (DSC). Reversible transitions were determined at 643 K with a standard enthalpy of transition [(6Htr)] = 0.74 kca1/mol, at 679 K with a [6Htr = 0.65 kca1/mo1, and at 868 K] with a standard enthalpy of fusion [(6H~) = 1.895 kca1/mol.] Tabulated values are listed at selected temperature increments from 298.15 to 1,600 K for the standard relative enthalpy (HO -H298), heat capacity (CpO), entropy (SO), and Gibbs energy function [-(Go -H298)!T]. The enthalpy data are also given in the form of equations and combined with thermodynamic data from other investigations to derive values of standard entha1pies of formation [(~HfO)], Gibbs energies of formation [(6GfO)], and logarithms of the equilibrium constants of formation (log Kf).

Jan 1, 1987

By Fred N. Kissell

Methane flows and pressures were measured in mines in the Pittsburgh, Hartshorne, and Pocahontas No. 3 coalbeds. From the data, the permeability of each of these coal beds was computed. It was found to depend strongly on the type of coal and on the amount of water in the coalbed, and it was found to increase with time. All of the coalbeds had a high-permeability zone adjacent to the face or rib, and the Pittsburgh bed exhibited directional anisotropy. Surprisingly, little or no overburden effect was observed.

Jan 1, 1972

By Clarence O. Babcock

ROCK BEHAVIOR has proved of national interest in a variety of fields. The behavior of rock consequent to a nuclear blast was used to detect such blasts, as criteria for the design of underground military defense installations that would resist nuclear blasts, and for judging the feasibility for peaceful uses of nuclear explosives. An obvious peaceful application of nuclear explosives would be for large-scale rock excavation, and plans were presented during the year to improve the present Panama Canal or create a new canal by this method. These plans were based largely on earlier crater tests that demonstrated rock behavior when subjected to a buried nuclear blast. A knowledge of rock behavior under impact was used to evaluate the materials of the moon by means of the geometric configurations visible in the close-up pictures of the moon surface taken by the U.S. rocket Ranger 7. The composition of the moon must be considered in devising methods for taking samples of the surface layers or in designing underground shelters as bases for future explorations of the moon.

Jan 1, 1965

By Kenneth M. Earl

In its program of investigation of deposits of strategic minerals, the Bureau of Mines did some development drilling at the Tapley deposit in an endeavor to find an additional source of copper. There are accounts that many years ago the property had some production; there are several old, inaccessible shafts apparently sunk on a vein in rhyolite or diabase. The waste dumps of these shafts contain considerable sulfides, chiefly pyrite and chalcopyrite. To cut the vein below the old mine workings, the Bureau of Mines? diamond-drilled five holes aggregating 1,204 feet. No significant copper mineralization was found.

Jan 1, 1950

By Lloyd A. Morley

To reduce safety and production problems, it is essential that the electrical operating characteristics of coal mining equipment and their electrical subsystems be clearly understood. The Bureau of Mines and the Pennsylvania State University have developed techniques to monitor and analyze several of the critical parameters. A unique system for measuring traction locomotive consumption at the machine has been assembled and utilized. Conclusions from 27 continuous miners show that voltage levels are directly tied to machine efficiency. The Bureau of Mines and Pennsylvania State University, along with West Virginia University, are currently monitoring and accessing mine power transients. Results exhibit that voltage transients of three to five times the line -to-line value are common on underground distribution systems.

Jan 1, 1975

By Robert R. Stein, Roy C. Bartholomae, William W. Aljoe

This Bureau of Mines report describes in detail the design and operation of a test apparatus for measuring the sound power levels of drills used by the mining industry. The two major components of the test apparatus are a computer-controlled automated drill test fixture (ADTF) and a large (45,000-ft3) reverberation chamber that houses the ADTF. Design specifications and performance capabilities of the ADTF and the reverberation room are given. Initial test results for three types of drills--a pneumatic percussion drill, a hydraulic percussion drill, and a pneumatic rotary drill--are given to illustrate the types of experiments that can be conducted with the test appartus.

By Alton B. Cook

Data are presented to show oil vaporization resulting from the passage of natural gas through a sand-packed tube saturated with synthetic reservoir oils. The Bureau of Mines performed 13 experiments, using reservoir oils synthesized with base crude oils of approximately 22°, 35°, and 45° API, at 100°, 175°, or 250° F and 1,100, 2,600, or 4,100 psia. It has been determined that the amount of vaporization is significant if proper conditions exist. These experiments show that oil vaporization depends on pressure, temperature, volatility of the oil, and amount of gas cycled. Increases in each of these conditions increase the volume of oil vaporized.

Jan 1, 1969

By R. C. Wang

Solid-liquid flow in different pipe geometries was investigated. This investigation was conducted by measuring delivered solids concentration and head loss. The delivered solids concentration was measured to study the effect of pipe geometry on the minimum carrying velocity above which solids do not lag behind the fluid. Head loss was measured to study the effect of pipe geometry on the friction loss. A mathematical formula was developed for determination of the minimum carrying velocity. Darcy-Weisbach's equation and Durand's equation were used for comparison of head losses of pipe shapes. Of the different pipe shapes studied, each having the same interior cross-sectional area, the rectangular pipe with the wide side oriented as the base yielded the lowest minimum carrying velocity at high solids concentrations. The minimum head loss at low velocity and high solids concentration also was attained with this pipe. Although the circular section is known to be the best for transporting liquid only, the present study suggested that pipe geometry is a factor in lowering the operating velocity and reducing head loss in solid-liquid flow.

Jan 1, 1973

By Robert P. Vinson

This report describes three coal mine ventilation studies by the Bureau of Mines in which sulfur hexafluoride (SF6) was used as a tracer gas. One of these studies was conducted to determine air movement and leakage in a sealed area. Another was run to determine the ventilation efficiency of a bleeder system. Finally, a study was made of air leakage across permanent stoppings of parallel intake airways. These studies proved sulfur hexafluoride to be a useful addition to the equipment commonly used in coal mine ventilation analysis.

Jan 1, 1976

By Robert J. Timko, Edward D. Thimons

Sulfur hexafluoride (SF6) is an odorless, colorless, nontoxic gas that has found acceptance as a tracer gas in research on ventilation pat- terns, measurement of air leak rates, respirable dust reductions due to bagging hood modifications, and the study of airflows relating to gob boreholes. Following a short review of the SF6 sampling technique, this report describes recent Bureau of Mines projects in which SF6 was used successfully as a tracer gas, enabling researchers to acquire representative data quickly and inexpensively.

Jan 1, 1982

By J. D. Hadden

The Bureau of Mines conducted drilling studies in the Pocahontas No. 3, the Pittsburgh, and a western coalbed to establish the gas migration characteristics for each. Gas pressures in the Pittsburgh coalbed were about 260 lb/in2 and in excess of 550 lb/in2 in the Pocahontas No. 3. Caving in drill holes prevented pressure measurements in the western coalbed. The Pittsburgh coalbed contained intersecting "clay veins" which formed gas pressure cells. Although these geological features hamper mining, they can be used to control the flow of methane into a mine working. Methane control techniques are proposed for the Pittsburgh and Pocahontas No. 3 coalbeds.

Jan 1, 1969

By Stephen A. Hare, O&apos

The melting, casting, and welding of the Raney nickel alloy (42 pct Ni-58 pct A1), a methanation catalyst useful in coal gasification, were investigated. Melting was done in graphite crucibles by heating aluminum and adding nickel using a cryolite slag cover. Casting conditions were found to be optimum when the melt temperature ranged from 1,125° to 1,200° C and the mold temperature ranged from ambient to 250° C. Suitable mold materials were found to be quartz, heat-resistant glassware, olivine, and zircon. Welding of the alloy can be accomplished using tungsten inert gas process. Tensile strength of the alloy, in the as-cast condition, was found to be 2,000 1b/sq in with an impact strength of less than 1 ft-1b. The coefficient of thermal expansion was determined to be 18.4 x 10-6/° C after heat treatment.

Jan 1, 1977

By Robert L. Lagace

The attention of this group was focussed on four through-the-earth communication systems that are presently of high interest to the U.S. Bureau of Mines; four systems for providing operational/emergency communications on the working sections of coal mines, indeed up to the very face of the section. The systems are: uplink-data, downlink-voice, sidelink-call alert coded page, sidelink-roof bolt voice page. Each of these systems makes use of the mine overburden as the signal transmission medium, as opposed to the guiding wires, cables, and tunnels treated by the operational communications working group. Each of these systems satisfies one or more of the Bureau's objectives for mine communications systems; namely • reliable links for monitoring the mine environment under both operational and emergency conditions. • reliable links for communicating with miners during emergencies. • special links for increasing the efficiency of day-to-day operations of the mine. Each of these systems has been successfully demonstrated on a limited experimental basis, and prototypes of all these systems are installed and operating in the USBM experimental mine in Bruceton, Pa. Each of these systems must now be optimized regarding its performance, and engineered for practical routine application to the working sections of actual operating coal mines, particularly those of the room and pillar type. This optimization and engineering must take place subject to the principal constraints listed by Howard E. Parkinson in his Workshop paper entitled, "Objectives and Constraints of Through-the-Earth Electromagnetic Communications Systems'' and enumerated below. • Depth of Mine Overburden • Overburden Conductivity • Electromagnetic Noise In and Above Mines • Limited In-Mine Electrical Energy (Stationary or Man Carried) During an Emergency • Intrinsic Safety for In-Mine Equipment • Practical and Rugged Equipment for Use Under Both operational/Emergency conditions • Severe Weight Limitations for Man Carried Equipment • Reasonably Low Costs Especially for Man Carried Equipment Part II of this paper provides a brief description of each system, while Part III summarizes the present status of developments related to these systems and some recommendations for future work needed to advance these systems to the practical application stage.

Jan 1, 1973

Improve face ventilation in mines with large cross-sectional entries. Approach Oil shale, salt, and limestone mines typically have large entries. Providing adequate airflow to the working faces of such mines for worker comfort, health, and safety is a substantial ventilation problem. If diesel equipment is used at the face or if a methane hazard exists in the mine, the problem becomes even more complex. To address this problem, a study was conducted under a joint contract between the Oil Shale Committee of the Colorado Mining Association and the Bureau of Mines. The study evaluated two face-ventilation concepts for large-entry mines. Improving Ventilation Two face-ventilation systems were selected for testing of an oil-shale mine, based on results of a cost/benefit analysis. The systems were a free-standing jet fan and a ducted fan operating in the blowing mode. The jet fan was spotted on the intake side in the mouth of the entry being advanced with final positioning, in or out, deter-mined by minimum recirculation. The ducted fan was also positioned in the mouth of the entry being advanced, with its tubing terminating 75 feet from the working face. The mine face entry was a dead heading 55 feet wide, 30 feet high, and 320 feet long. Sulfur hexafluoride (SF.) tracer gas was used to measure the performance of the two systems in diluting mine face pollutants including after-gases from blasting, hot diesel emissions, methane roof layers, and methane emitted from muckpiles.

Jan 1, 1987

Determine the extent to which remote-sensing techniques, primarily lineament analysis, can be used to identify geologic structures that may affect the location and migration of subsidence over abandoned underground coal mines in the Colorado Springs, CO, area. Compile data using a geographic information system (GIS) to allow efficient and reproducible comparisons and analyses. Background The basis for evaluating abandoned mine land (AML) sites with remote-sensing techniques comes from past and ongoing Bureau ground control research using remote-sensing data to identify potential hazards caused by geologic structures (faults, joints, etc.) above active underground coal mines. Research showed that lineament (linear feature) analysis of Landsat Multispectral Scanner (MSS) images could indicate locations of fractures and fracture trends that had varying, but significant, impacts on the stability of mine openings. Such geologic structures should be identifiable over abandoned mines as well. If fractures are present, even if they arc not faults, they should represent areas of potential instability over these mines and, therefore, should tend to localize subsidence when it occurs, particularly for deep and moderately deep portions of mines.

Jan 1, 1992

Provide a machine for economically drilling probe holes in coal mines (required where there's a possibility of unmapped, abandoned workings) to check for possible water flood or gas hazards ahead of the face. Approach A lightweight air-powered drill, that mounts on a light-weight frame anchored to the face with an expandable packer, is used to drill one or more probe holes. The anchor installs quickly and will lock the drill in any desired position. How It Works The drill is portable and can be broken down to small components for ease of transportation. One man can carry these sections through restricted access routes to the working place. Components that are separable are the anchor assembly, drill frame assembly, and drill motor assembly. The drilling sequence is as follows: A 2-inch-diameter anchor hole is drilled 2 feet deep. The fixed anchor tube is rubber packer is expanded. A second anchor hole is drilled through a bushing in the anchor frame. The removable anchor tube is inserted and its rubber packer expanded. (This anchoring system withstood pulls of up to 14,000 pounds.) Next, the frame is attached to the anchor with two screw knobs, and the motor is attached to inserted in the hole and the rubber packer is expanded. A second anchor hole is drilled through a bushing in the anchor frame. The removable anchor tube is inserted and its rubber packer expanded. (This anchoring system withstood pulls of up to 14,000 pounds.) Next, the frame is attached to the anchor with two screw knobs, and the motor is attached to the frame with a single locking pin. Installing the anchor and drill takes less than 12 minutes.

Jan 1, 1981

By J. A. Lamonica

The Bureau of Mines studied two types of approved coal mine dust personal samplers to determine the effect of decreasing the amplitude of airflow velocity fluctuations on cyclone performance. Results indicate that more dust is collected when pulsation free flow is used. Velocity fluctuations were reduced by means of a pulsation damper; damper efficiency of about 85 percent was needed to reduce the fluctuations to an acceptable level. The data were obtained employing both pulsating and non-pulsating flow. A comparison was made of (1) the masses of respirable coal dust as determined by weighing and of (2) the particle size distributions as determined by an electronic counter. An empirical relationship is given between the ratio of masses collected using pulsating and nonpulsating flow (M') and the ratio of the maximum air velocity to the minimum air velocity (V') as measured in the cyclone entrance channel.

Jan 1, 1972

By Manuel Gomez

Prediction models were constructed for seam elevation, overburden, and sodium concentration for a lignite deposit in Ward County; N. Dak. These models were developed by mathematical-statistical techniques using surface coordinates as independent variables to permit interpolation between drill holes. The results suggest that sodium concentration in lignite may be predicted in advance of mining. This information is helpful to mine planning, specifically, in scheduling production to deliver a uniform product to existing powerplants.

Jan 1, 1970

By W. Wallace, T. Ong, M. Gautam, M. Keane, S. Xing, J. Harrison

"Diesel exhaust soots were assayed in the Ames Salmonella typhimurium histidine reversion assay system using TA 98, the soots being applied as the following preparations: dispersion in dipaimitoyl glycerophosphoryl choline (DPL), dispersion in dipalmitoyl phosphatidylethanolamine (DPP!), and dispersion in dipalmitoyl phosphatidic acid (DPPA) in physiological saline, and in physiological saline without added surfactant. The extracts of soots by dichloromethane / dimethylsulfoxide (DCM/BHSO) were also assayed. Studies were performed both with and without :IQ microsomal activation of the soot preparations. The DPP! and DPPA surfactants were chosen as phospholiridz with two palmitic acid moieties esterified to a glycerol as is the case with DPL, but with hydrophilic groups having different electrophilic characters. The soots, without S9 activation, showed mutegenic activity when extracted in the conventional procedure with DCM/DMSO. The mutagenic activity of soots dispersed in DPL was quantitatively comparable to, and in some cases greater than, the activity expressed by an equal mass of soot extracted by DCM/DMSO. Soots in other surfactantpreparations, DPP! and DPPA, also expressed positive mutagenic activity. Praincubation with S9 microsomal enzyme fraction reduced the activity of solvent extracted soots, and greatly diminished the activity of DPL dispersed soots. Initial sister chromatid exchange (SCE) assays using the Chinese hamster V79 cell line indicated DPL dispersed soot also can cause SCR in mammalian cells. Results thus far suggest that surfactant suspended or ""solubilized"" respirable soot particles could provide a mechanism for transport and expression of mutagens in the lung."

Jan 1, 1989