Search Documents

By Lloyd A. Morley, Alan M. Christman

General Six open-pit metal mines, five copper and one molybdenum, were visited during the course of the research. Four were investigated twice, in summer and in winter, in order to determine the effects of seasonal variations In temperature and moisture upon the measured parameters, Permission to enter the fifth mine was received too late to make an examination during the summer months. The sixth mine was visited to confirm the results obtained from the other five and specifically, to observe how the project recommendations (as will be presented in this chapter) would apply to open-pit metal mines in general. Information gathered during the ten plant visits is sufficient to form an adequate data base for the report. A complete presentation of all field trip data is given in Appendix 1. Further, a detailed description of the electrical distribution and grounding practices at each mine is also contained there. Typical System. At a typical mine as shown schematically in Figure 62, one or more substations with resistance-grounded secondaries are employed to transform the incoming utility-voltage to the lower potential used by the mining machines, generally three-phase 4160 V. At this level, pit distribution is carried on overhead lines, supported by wooden poles, to supply switchhouses located in benches near the particular piece of equipment. A switchhouse is a small portable (often skid-mounted) structure at the termination of an overhead line which contains disconnect

Jan 1, 1976

Reduce longwall intake contamination by controlling respirable dust generated by the stage loader. Approach Install a water-powered scrubber on the stage loader immediately outby the crusher. Dusty air from the crusher is drawn through the scrubber and a clean air discharge is delivered into the primary face airflow. How It Works The contamination of intake air is a significant dust control problem often overlooked on many longwall faces. This dust source contributes to the full shift dust exposure of all face personnel, and thus can significantly affect compliance with Federal regulations. Several sources contribute to contamination; however, dust generated by the stage loader crusher is the single largest source. The breaking action of the crusher generates a tremendous quantity of dust, which mixes with the primary ventilation airstream and is carried down the entire length of the longwall face. The installation of a water-powered scrubber (see diagram) has proven effective in controlling crusher-generated dust. The scrubber is mounted immediately outby the crusher. A duct is placed over the scrubber intake and attached to a flanged opening over the crusher discharge. In

Jan 1, 1982

By Richard J. Mainiero, Sapko, Marcia L. Harris

Since 1988, there have been thirteen documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through near surface strata into structures or other enclosed spaces as a result of nearby trench blasting or surface mine blasting. From these incidents, there are thirty suspected or medically verified CO poisonings and one fatality associated with these incidents. To better understand the variables contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out a small-scale field study to identify key factors that may contribute to the migration of CO through the ground. NIOSH conducted single-hole heavily confined experimental test shots to measure the radial pressure pulse as it propagated through surrounding monitoring holes to determine if a relationship existed between the pressure pulse and resulting CO measurements afterwards. NIOSH also monitored blasts at an airport construction site. Following the detonations, the concentrations of CO, nitric oxide (NO), and nitrogen dioxide (NO2) were monitored for several days in the surrounding satellite holes. The peak CO measurements relative to distances from the shots were compared. Pressure histories and peak particle velocities (PPV) were measured at monitoring boreholes. It was found that the differential pressures recorded within the boreholes give some indication as to the likelihood of CO appearing, whereas the PPV measurements do not seem to be as good an indicator for potential CO migration. In this limited study, changes in barometric pressure had very little influence on removing the trapped detonation products, whereas applying a vacuum to the monitoring holes was effective in reducing the entrapped CO concentration.

By D. Harrington

"The fire boss in coal mining and the shift boss in metal mining, though held responsible to a large extent for safety of underground employees and of the mine, are, it seems to me, not always vested with sufficient authority nor given compensation commensurate with their duties. The metal-mine shift boss, although his position as regards his relations between employer and employee, is frequently an unenviable one, has as a rule much more authority than the fire boss and is not expected to perform the menial tasks required of the latter by many coal-mining companies.In most coal-mining States the coal-mine foreman and the fire boss are re¬quired to possess a certificate of competency obtained by passing an examination. The foreman is legally responsible for the safety of the miners, as in most instances the superintendent is not required to pass an examination. Although the foreman is held legally responsible for the safety of the miners, the law does not, in general, compel the superintendent or other higher officials to delegate sufficient authority to the foreman to enable him to put his wishes or judgment into effect; and this condition has tended in many instances towards perpetuation of unsafe conditions.The fire boss is held legally responsible for conditions in his ""beat"", but he is generally given only such authority as the mine foreman sees fit to delegate, frequently very little, Moreover, the fire boss is generally required to cover his ""beat"" within two hours before the entrance of the underground workers. Only too often his territory is so great that in order to reach all the working faces and chalk the required date at the face, he must travel at a rapid walk or even run. When such haste is necessary to cover the required ground, it is manifestly im¬possible for the fire boss to make a careful inspection or examination of the roof, timbering, wiring, gas, etc., at each place, and doubtless in his hurry many unsafe conditions escape his notice."

Sep 1, 1920

By Michael J. Pazuchanics, Thomas J. Fisher, John J. Sammarco, Jeffrey H. Welsh

This report (An Introduction to Safety) is the first in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment's life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics, and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard 61508 and other recognized standards. The scope is "surface and underground safety mining systems employing embedded, networked, and non-networked programmable electronics." System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system's safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a "proof of safety" that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full life cycle of the system, and provides administrative support for the safety program of the full system. [ ]

Jan 4, 2001

By Frank J. Susko

The U.S. Bureau of Mines is developing a process for removing metals from mining and mineral processing waste streams by precipitation. The precipitation process is accelerated by flocculation when a high molecular weight polymer is added. Infrared (IR) studies were performed on zinc hydroxide [Zn(OH);J, copper hydroxide [Cu(OH);J, and zinc sulfide (ZnS) flocculated with both non ionic and anionic polyacrylamide (PAM) and polyethylene oxide (PEO). The IR data were compared with general trends in the performance of the polymers observed during flocculation. These studies will help to understand the bonding between the precipitate and polymer and indicate the effectiveness of a flocculant for dewatering. Two types of bands showed up on the IR spectra; one type described the interlayer water of the flocs, the other described the organic bonds of the polymers. A general decrease in the areas of the three water bands, hydroxyl (O-H) stretching (3,200-3,500 cm-1), water bending (1,610-1,630 cm-1), and torsional oscillations (600-700 cm-1), indicate interlayer water being driven off, which is a favorable condition in flocculation. Shifts in the O-H stretching band indicate water bridging between the precipitate and polymer. Shifts in the amine (N-H) deformation, carbon-nitrogen (C-N) stretch band (1,600-1,610 cm-1) indicate the amine group of the PAM is involved in the bonding. Evidence suggests that ether oxygen of PEO is also involved in the bonding process.

Jan 1, 1990

Estimate costs for projected uranium in-situ mining operations. Approach Develop a computer model and an associated data base which will allow users to supply data applicable to a specific mining site in order to estimate total capital and operating costs for a potential in-situ mining operation at the site. How the Model Works The model requires a minimal amount of input from the user. The data input must be known or estimated information about a potential in-situ mining operation. The user can also supply any additional project specifications. The computer model uses a process-engineering approach and determines through a discounted cash flow analysis the total capital and operating costs for the life of the project. This time-span measures from the start of the pilot-scale operation through to the site's restoration and reclamation. The model will determine the production cost per pound of material mined subject to the rate of return identified by the user. Conversely, it will also solve for the rate of return realized for the specific sales price per pound. [ ] Currently the model's data base can tai ns costs, rates, and specifications for Texas and Wyoming, the only states where commercial uranium in-situ mining is being conducted. However, this model can be used by anyone who is conducting in-situ leaching or who plans to leach uranium in-situ. At least part of any uranium deposit has a potential for in-situ mining.

Jan 1, 1982

Engineering controls for overburden drilling include dry dust collection systems, wet dust suppression systems, and enclosed cabs [Zimmer and Lueck 1986; Volkwein et al. 1979]. Proper maintenance of the dust suppression system is critically important for drills using dry dust suppression methods. Failure to rigorously maintain these systems will result in inadequate dust control. Acute silicosis has been reported in miners operating equipment that relies on dry dust suppression [NOSH 1992].

Jan 1, 1997

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

TEST DECK – ALTMETER SURVEY WITHOUT PLTTMETER TEMPERATURE CCRRECTION DATA INPUT

Jan 1, 1977

By Charles E. Whieldon

This report presents the results of a study on part of the Smithfield oilfield, Wetzel County, W. Va. The primary purpose of the investigation was to determine the original and the present volume of stock-tank oil in the formations and to investigate the feasibility of waterflooding the Gordon Stray, Gordon, and Fourth sands underlying the I. D. Morgan lease. The study was based on laboratory core analyses, geophysical well logs, geologic considerations, and various field prediction data from the I. D. Morgan lease. The Bureau found that, of the three sands cored, the Gordon Sand was the best prospect for waterflooding, and that a properly engineered water flood should recover 136 to 230 barrels of oil per acre-foot from this formation.

Jan 1, 1967

By B. T. Brady

Results of a study are presented of the effect of low radial reinforcement pressure on the postfailure characteristics of two types of granite, a sandstone, and marble. The low radial reinforcement pressure is applied to the rock surface by a gooch rubber sleeve. The gooch rubber sleeve provides a radial pressure of less than 1 psi pressure to the rock surface. This method of support gives an average strength increase of approximately 8 percent to the fractured rock sample.

Jan 1, 1973

By Oscar Lee

"Flotation is generally regarded as a process that is only applicable to metallic minerals. However, its scope is now known to be greater than this, because some of the nonmetallic minerals are floatable, such as graphite, sulphur, and fluorite. Recent observations show that limestone may be added to the list of floatable nonmetallic minerals. Such work is being done on a laboratory scale at the Southern Experiment Station (Tuscaloosa, Ala.) of the Bureau of Mines, Department of Commerce, where experimental magnetic concentration of the low-grade iron ores of the Birmingham district is in progress. Certain experiments have demonstrated that the limestone may be floated from the magnetic log-washer tailing, and then incorporated in the iron concentrate.If the loss of lime could be prevented, some ores though low in iron and high in insoluble contain enough lime to make their concentrates self-fluxing. Since this loss in the magnetic log-washer can not be avoided, the Time must be recovered from the tailing by some method and added to the magnetic iron concentrate before sintering. Then the resulting concentrate will be self-fluxing.While seeking a suitable means of treating the tailing for recovery of lime, flotation was tried. It was at once evident that this method had possibilities, during the early part of the investigation, soap solution made from a common soap was used as a flotation reagent. The froth obtained was a fairly good lime concentrate. This result was an important clue, and led to tests with the use of such reagents as oleic acid and sodium oleate. Later, cresol, creosote, coal tar and other similar flotation reagents were tested in combination with the oleic acid and soap solutions. As a result, oleic acid and cresol used together were found to be satisfactory.The tailing from the magnetic log-washer is in excellent physical condition fur flotation. The iron ore had been ground in a ball mill to 100 mesh for magnetic concentration. Hence the bond between the lime carbonate and the other constituents of the tailing was well broken."

Apr 1, 1926

By an Slo, J. J. Forbes

"INTRODUCTION This is the first of a series of information circulars dealing with the control of roof and the prevention of accidents from falls of rock and coal. These circulars are being published to focus attention of the coal-mining industry on this most prevalent source of fatalities and injuries and to present factual information that should be helpful in reducing loss from these causes.Records of fatal accidents in the coal mines of the United States, from all causes, have been kept since 1906; during this period approximately 30,000 men have been killed by falls of rock and coal in the bituminous-coal mines, and more than 7,000 men have lost their lives in the Pennsylvania anthracite mines from the same causes. From 1906 to 1930, about 900 men were killed annually by falls of rock and coal in bituminous-coal mines, and about 200 men were killed annually in anthracite mines during the same 25-year period. From 1931 to the present time, the number killed annually from falls of rock and coal has averaged more than 500 men in bituminous-coal mines and about 125 men in Pennsylvania anthracite mines.Numerically the record of accidents from falls of rock and coal shows improvement, but on a percentage basis and on a million-man-hours-of-exposure basis little, if any, improvement has been made during the past 40 years. The cold fact is that, year after year, about 50 percent of all those killed in coal mines in the United States lose their lives from falls of rock and coal."

Apr 1, 1948

By John M. Gomes

Two methods for electrowinning tungsten from wolframite [(Fe,Mn)W04] were investigated. The first method, direct electrowinning from wolframite concentrate dissolved in molten salt mixtures composed essentially of various combinations of sodium phosphates, sodium borates, and sodium halides, yielded impure products. The second method was electrowinning from a halide-tungstate melt that was obtained from a high-temperature, two-phase extraction of tungstic oxide (W03) from wolframite. Electrolysis in electrolytes prepared from addition of sodium metaphosphate (NaPO3) and boric oxide (B2O3) to the halide-tungstate melt produced tungsten metal of 99.9 percent purity. Tungsten carbide (WC) was electrodeposited from the halide-tungstate melt when the melt was adjusted to contain 82 mole-percent NaCI and 6.0 mole-percent each of W03, sodium metaborate (Na2B204), and caustic soda (NaOH).

Jan 1, 1970

To develop and design a bit that will rapidly drill smooth and precise instrumentation holes in soft rock. Approach Use a one-piece bit made by combining a drag bit and a diamond bit. Because a smooth-walled borehole with a precise diameter is needed for borehole pressure cells (BPC) and other borehole instruments, a diamond bit is usually used. However, diamond bit drilling is slow, and the bit will tend to bind when squeezing ground is encountered. On the other hand, the drag bit will cut faster, but the walls of the drill hole will be rough and the diameter will not be as precise. The combination will provide a bit which penetrates as rapidly as a drag bit, but retains the smooth-wall and precise borehole diameter of a diamond bit. How It Works A three-foot-length of EW-size drill rod is centered in a diamond bit by welding it to three equally-positioned spacers at each end of the bit. A drag bit is attached to the EW rod with a standard EW-to-drag bit adapter as shown in the diagram. Three equally-spaced diamond inserts are set to the desired hole size and welded to the diamond bit barrel behind the crown. These inserts increase the smoothness and precision of the hole by cut-ting away any hole closure. Three equally-spaced shims are set approximately 0.020-inch under the overall insert diameter size and welded to the rear of the diamond bit barrel. The combination bit should be used on a diamond drill with either water, mist or air as the coolant.

Jan 1, 1982

By Isaac A. Zlochower, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) conducted a study of the explosibility of various metals and other elemental dusts, with a focus on the experimental explosion temperatures. The data are useful for understanding the basics of dust cloud combustion, as well as for evaluating explosion hazards in the minerals and metals processing industries. The dusts studied included boron, carbon, magnesium, aluminum, silicon, sulfur, titanium, chromium, iron, nickel, copper, zinc, niobium, molybdenum, tin, hafnium, tantalum, tungsten, and lead. The dusts were chosen to cover a wide range of physical properties-from the more volatile materials such as magnesium, aluminum, sulfur, and zinc to the highly "refractory" elements such as carbon, niobium, molybdenum, tantalum, and tungsten. These flammability studies were conducted in a 20-L chamber, using strong pyrotechnic ignitors. A unique multiwavelength infrared pyrometer was used to measure the temperatures. For the elemental dusts studied, all ignited and burned as air-dispersed dust clouds except for nickel, copper, molybdenum, and lead. The measured maximum explosion temperatures ranged from "-1550K for tin and tungsten powders to "-2800K for aluminum, magnesium, and titanium powders. The measured temperatures are compared to the calculated, adiabatic flame temperatures.

By Stephen W. Lambert, Michael A. Trevits

The Bureau of Mines examined the wellbore of a vertical gas drainage well in the Mary Lee coalbed to determine the results of specific completion procedures in coal. A jet-slotting tool was used to cut four vertical slots through the casing about 1 ft below the coalbed. Even though stimulation treatment pressure was excessive, hydraulically induced channels were contained entirely within the target coal zone. Sand-filled, induced channels were horizontal, inclined, and vertical, and were propagated in directions similar to bedding planes, rock joint, and coal cleat directions measured in the mine. Variable gas flow rates, recorded during the productive life of the well, were attributed to chronic downhole pump malfunction and the slotted casing below the production zone.

Jan 1, 1978

By E. G. King

Cerium and thorium sulfides have found use as crucible materials for melting certain radioactive metals. However, thermodynamic treatment of these sulfides has been hampered by lack of experimentally derived entropy values. This Bureau of Mines report describes heat-capacity measurements between 51° and 298° K, and entropy evaluations at 298.15° K, for cerium monosulfide (CeS), cerium sesquisulfide (Ce2S3), and thorium disulfide (THS2). The entropy values, with Literature results for the heats of formation, are used to obtain free energies of formation at 298.15°K. MATERIALS The samples used in this work were supplied by Prof, Leo Brewer of the Department of Chemistry, University of California. The methods of preparation and some of the physical and chemical properties of these sulfides were given by Eastman and coworkers.3 4/ Chemical analyses, conducted in our laboratory, gave the following results:

Jan 1, 1959

By R. P. Vinson, Abdurrahman Cetinbas, Joseph Cervik, M. G. Zabetakis

The periphery of longwall panels in the Pocahontas No. 3 coalbed is characterized by a zone of reduced permeability that inhibits the natural drainage of methane. A residual gas pressure of 105 psig was measured after 1 year in an isolated block of coal measuring 340 by 1,100 feet. The buildup of gas pressure within such large blocks causes methane problems during plowing operations. However, natural drainage holes drilled during development have been found to reduce the gas content of the coal in this coalbed by over 90 percent. The effect of water infusion on dust during plowing operations was investigated using existing methane drainage holes. These holes were cleaned of debris and a pipe was grouted into the hole for water infusion of the panel. Both total and respirable dust levels were reduced by 40 to 79 percent. Water infusion of the panel proved more effective than did the use of a plow-mounted spray sys tem.

Jan 1, 1974

By H. C. Ko

As part of the Federal Bureau of Mines effort to provide thermodynamic data for the advancement of minerals technology, energy conservation, and environmental preservation, the standard enthalpies of formation of a-magnesium sulfate, a-magnesium sulfate, and magnesium sulfate monohydrate were determined by hydrochloric acid solution calorimetry. The values of the standard enthalpies of formation in kcal per mole at 298.15 K are -307.95 ± 0.13 for a-MgS04, -307.03 ± 0.13 for ß-MgS04, and -384.72 ± 0.13 for MgS04 .H2O.

Jan 1, 1979