Search Documents

By Edward Cogan

Equilibrium phase diagram studies of zirconium- rare earth metal alloys by the Bureau of Mines at its Albany Metallurgy Research Center prompted the development of a rapid gravimetric method for determining rare earths in zirconium in which the rare earths are absorbed from sulfuric acid solution of the alloy on a cation exchange resin . The sample in 10 percent H2SO4 is introduced into the column , the zirconium is eluted with 10 percent H2SO4 , and the rare earths are eluted with (NH4 )2SO4 solution and precipitated with NH4OH . A tracer technique was employed to determine the efficiency of the procedure . Y203 and europium 154 - 152 (Oak Ridge ) were added to 10 g of zirconium and taken through the entire procedure . Recovery averaged 97.6 percent on 0.002 μg europium in the rare earth fraction . Rare earths were determined in the range 0.10 to 90 percent .

Jan 1, 1964

By Fred N. Kissell

In this report the importance of diffusion in controlling the emission of methane in mines is examined. An in-situ diffusion parameter is defined and calculated for a hypothetical unfractured lump of coal in the Pittsburgh and Pocahontas No. 3 coalbeds. The values obtained are similar to those obtained with lump coal in laboratory experiments.

Jan 1, 1972

By C. Stephan, E. Weiss, J. Trackemas, M. Sapko

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), in collaboration with the Mine Safety and Health Administration (MSHA), the mining industry and seal manufacturers, conducted a series of full-scale experiments within the underground experimental mine at PRL's Lake Lynn Laboratory. The purpose of the experiments was to evaluate the explosion-resistant characteristics of several new seal designs for rapid deployment during mine emergencies. These seals can be deployed in less than 12 hours and are capable of withstanding explosion overpressures in excess of 140 kPa (20psi). These novel seal designs use available mine materials, do not require conventional rib hitching and, most importantly, can substantially reduce exposure time for coal miners during sealing and mine recovery operations.

By C. B. Manula, R. L. Sanford, R. A. Rivell

This report was prepared by The Pennsylvania State University under USBM Contract No. 60111808. The contract was initiated under the coal Mine Health and Safety Program. It was administered under the technical direction of DMSE, with M. G. R. Schottler acting as the technical project officer. Mr. J. A. Herickes was the contract administrator for the Bureau of Mines.

Jan 1, 1974

1. In 2002, a total of 4,311 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA). The major industrial classifications in stone mining are dimension stone (used for construction purposes), crushed and broken stone (aggregates), cement, and lime. Stone mines comprised 29.7% of all mining operations. • Mines producing crushed and broken stone (n = 3,372) comprised 78.2% of all stone mining operations.

Jan 1, 2004

By John W. Frey

This paper presents one of a series of digests of foreign mining legisla- tion and court decisions which is being prepared in advance of a general report relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Trinidad has been prepared from the best information available in ashington but is released subject to correction and amplification, if necessary, by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State.

Sep 1, 1930

By Dorsey A. Lyon

At the main experiment station of the U. S. Bureau of Mines , situated in Pittsburgh, Pa . , three phases of its work in behalf of the safety of the coal miner are the establishment of permissible explosives for use in gaseous and dusty mines , the development of electrical equipment that can be used with safety in mines of this character , and improvement in the safety of mechanical devices used in and about the mines . Also That these efforts are beginning to have a cumulative effect in lives. saved is evident from the fatality statistics of the industry . Although nearly 80,000 more men are employed in coal mining than ten years ago and much more coal is mined , the fatalities each year are considerably less than ten years ago . the amount of coal mined in a year for each life lost has risen between 60,000 and 70,000 tons . In 1909 , the year before the Bureau was created , the production of coal for each life lost was 174,416 tons . In 1920 , the production for each life lost was 285,000 tons .

Mar 1, 1921

By W. W. Weller

Heat-capacity measurements of sodium dimolybdate (Na2Mo207) and sodium ditungstate (Na2W207) were conducted over the temperature range from 51° to 298° K. The entropies of the two compounds at 298.15° K were calculated from the heat-capacity values and were used, in conjunction with other entropy data, to evaluate the entropies of formation of the compounds from their constituent elements and oxides.

Jan 1, 1963

By E. G. King, W. W. Weller

Low- temperature heat capacity measurements of muscovite were made in the temperature range from 50° to 298 ° K. The entropy at 298.15 ° K was evaluated as S298.15 = 69.0 ± 0.7 cal /deg mole .

Jul 1, 1960

By C. L. Severy

On the Pacific coast during World War II, a tremendous ship-building industry was developed, Early in the war it became impossible to obtain in- got or steel scrap for ship ballast. Magnetite, an oxide of iron, was sub- stituted as it fulfilled the requirements of weight for available space in the ships. Consequently, a new use for the western magnetite was rapidly developed.

Jan 1, 1948

By V. A. Marple, K. L. Rubow

"IntroductionA particle dispersion system has been developed to aerosolize bulk powders or material deposited on surfaces such as filters. The size distribution of the aerosolized particles can then be obtained by sampling the particles with an aerosol sizing instrument such as a TSI aerodynamic particle sizer (APS) or a cascade impactor.Of particular interest is the applicability of using this technique to obtain the size distribution of particles collected on filters. This system has been used to determine the size distribution of coal dust particle collected on membrane filters. The use of this device in this application is quite intriguing in that, if this technique can be shown to accurately determine the size distribution of airborne particles, one can easily collect particle samples using either personal or area particle samplers, determine the mass concentration of the collected material through gravimetric techniques and then use the particle dispersion system coupled with the APS to determine the particle size distribution. With this technique one can determine the particle size of dust in environments, such as underground mines, where it would be inconvenient or impossible to use a particle sizing instrument.Particle Dispersion SystemA prototype particle dispersion system has been developed for aerosolizing particles. A schematic diagram of the system is shown in Figure 1. The system consists of mechanism for advancing the particle sample beneath a dust pickup tube, a venturi for deagglomerating the particles, and a instrument for analyzing the aerosolized particulate matter.The procedure to analyze a particle sample is as follows. The particles to be aerosolized are placed on a sample plate from where the particles are picked up by an air stream flowing upward in a small capillary tube (dust pickup tube). This tube operates as a small vacuum cleaner passing over the sample plate. The air is drawn up the capillary tube at a rate of 2 L/m by a venturi aspirator. This is accomplished by placing the outlet of the capillary tube near the throat of the venturi. The accelerated velocity of the air creates a low pressure in this region which draws flow up the capillary tube. From the outlet of the capillary tube particles are transported to the inlet of the APS where a small fraction are sampled and the aerodynamic diameter of the particles determined. The particles which are not measured by the APS are passed into a HEPA filter."

Mar 1, 1989

By Lucia Kuizon

The Morongo Wilderness Study Area (WSA) is in south central San Bernardino County, California. U.S. Bureau of Mines examined the area during the fall of 1983. No mines, prospects, leases, or mining claims were found in the WSA. There are no known mineral deposits within the study area boundaries. Sand and gravel in the area is suitable for many types of construction uses, but similar and larger deposits outside the WSA are closer to markets. No energy resources have been identified in the WSA.

Jan 1, 1984

By H. J. Fissan, G. Ananth, K. Rubow, V. Marple

"INTRODUCTION Over the past several years a new type of cascade impactor that utilizes small nozzle diameters (micro-orifice nozzles) has been under development (Kuhlmey et al., 1981; Marple et al., 1981). The small nozzle dimensions allow for particles to be collected as small as 0.024 µm aerodynamic diameter on the last stage of the impactor. To obtain a reasonable flow rate of 30 I min - i through the impactor, a large number of nozzles (up to 2000) are required per stage.Furthermore, by locating the nozzles of multi-nozzle stages in a prescribed manner (described in detail by Marple et al., 1981) and rotating the impaction plates relative to the nozzle plates, uniform deposits can be achieved on the impaction plates. As described by Marple et al. (1981), the advantages of a uniform deposit impactor over the conventional impactor that collects particles only beneath stationary nozzles are: (1) maximum use of the impaction substrate surface, reducing both particle bounce (if substrates are greased) and tare weights of the substrates (if particle mass is measured gravimetrically); (2) deposited particles can be analyzed for elemental composition by X-ray fluorescence (Dzubay and Rieke!, 1978); and (3) the pressure in the impactor can be kept relatively high compared to low pressure impactors that depend on a large slip correction to achieve small particle collection (some types of particles may evaporate at low pressures). The work described in this paper investigates two additional advantages of a uniform deposit impactor. These are: (1) the possibility of collecting two separate deposits at one time on one stage for two types of analysis techniques, and (2) the possibility of utilizing piezoelectric quartz crystal impaction plates more effectively by eliminating the deposit location sensitivity nature of the crystals (Schulze-Frohlich, 1981 ).MICRO-ORIFICE UNIFORM DEPOSIT IMPACTOR (MOUDI)A photograph of an eight-stage MOUDI is shown in Fig. 1. Each stage body of the impactor supports the impaction plate for the stage above and the nozzle plate for the stage below as shown in Fig. 2. By rotating alternate stage bodies, while holding the other stage bodies stationary, the impaction plates (or nozzle plates) will be rotated relative to the nozzle plates (or impaction plates).Rotation of the alternate stage bodies is achieved by gears on these bodies that mesh with gears on an electrically driven drive shaft of a rotating mechanism (Fig. 1 ). The alternate stage bodies are restrained from rotation by pins that rest on the drive shaft."

Mar 1, 1989

By C. M. Mason

A series of gelatinous permissible explosives was prepared with increasing sodium nitrate content and subjected to an improved technique for evaluating incendivity in coal dust-air and coal dust-gas-air mixtures. Those explosives containing an appreciable amount of sodium nitrate were found to be very hazardous in coal dust-air and coal dust-gas-air mixtures.

Jan 1, 1969

By Robert W. Freedman, Benjamin I. Ferber, Wayne H. Duerr

Vacutainers are employed by the Bureau of Mines and the Mining Enforcement and Safety Administration for sampling mine air and other atmospheres containing fixed gases, low-molecular-weight hydrocarbons, and products of combustion. Tests were conducted to study shelf life of evacuated samplers prior to sampling and also to check the stability of sampled gases prior to analysis. An unexplained phenomenon, slow accumulation of carbon monoxide in evacuated samplers, occurred after a few weeks' storage; levels were low but increased with time and could pose a problem for critical applications. Accordingly, attempts to halt CO release by additional means of treatment were made, and storage at low temperature was found to be effective.

Jan 1, 1978

By C. M. K. Boldt, R. L. Levens, A. D. Marcy

Researchers at the U. S. Bureau of Mines conducted investigations to evaluate the potential for ground water contamination by mine waste used as backfill. Samples of cemented waste backfill and water discharging from drillholes and seeps were collected to use in chemical analyses and laboratory tests to determine the physical and chemical factors that control release of heavy metals to ground water. Greater water retention by cemented backfill (as compared to uncemented sandfill) reduces the surface are aexposed to oxidation, which in turn reduces the amount of acid produced. The acid is neutralized by the cement and minerals contained in the backfill. The grain-size distribution of tailings used for backfill affects the structural integrity of cemented backfill under attack by acidic water; breakdown of the backfill structure releases neutralizing materials faster. Backfilled stopes in rock with low hydraulic conductivities will constitute preferential flow paths after mine flooding; however, the rate of flow through backfill will be much slower than when the stope is partially saturated during mine operation. Considering all factors, acid generation and release of metal ions from cemented backfill should be less than in uncemented sandfill.

Jan 1, 1995

By J. E. Chilton

Regular monitoring for methane gas is required near working faces in gassy underground mines where the potential for methane ignitions is greatest. However, high concentrations of methane can also accumulate outby the face where methane levels are monitored less frequently. Wearing a personal methane monitor equipped with an alarm could protect persons working in these outby areas from injury or death due to methane ignitions. The National Institute for Occupational Safety and Health (NIOSH) has conducted studies to evaluate methanometers that could be used as person-wearable monitors. For the present study, seven different person-wearable monitors that are not currently approved for underground use were evaluated. This paper describes test procedures used to evaluate performance of methane monitors that could be used underground for continuous personal monitoring of methane. The information in this report provides data that allows the reader to make side-by side comparisons of these instruments.

By Judith A. Eisele

The possibility of improving the volatilization of gold through the formation of a metal-gold chloride vapor complex was investigated. Gold-silica mixtures, containing ferrous and nonferrous minerals and salts as additives, were treated in a laboratory tube furnace with a flow of chlorine gas at various temperatures. The addition of pyrite (FeS2) to a charge of gold-silica increased the volatility of the gold from 3, 20, and 62 percent of the total gold to 62, 93, and 100 percent at 200°, 300°, and 400° C, respectively. Chemical analyses of the condensate indicated the volatile species to be FeAuCl6.

Jan 1, 1971

By Andrew B. Cecala, Edward D. Thimons, George W. Klinowski

The U.S. Bureau of Mines has designed and evaluated total mill ventilation systems at two different mineral processing operations. Both systems have proven very effective at reducing respirable dust levels throughout the mill in a cost-effective manner. A 25,500-cfm system installed at a clay processing mill provided approximately 10 air changes per hour. This system reduced respirable dust concentrations by approximately 40 pct throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 50,000 and 100,000 cfm of ventilation to the mill building, corresponding to 17 and 34 air changes per hour. Average mill-wide respirable dust reductions were 36and 64 pct, respectively. Not only did these systems reduce respirable dust concentrations and increase visibility throughout the mills, they were also easy to install and required minimal maintenance. A total mill ventilation system provides a general purging of the mill air; the system should be viewed as a supplemental technique to assist other dust control systems in operation.

Jan 1, 1993

By R. J. Matetic

The National Institute for Occupational Safety and Health (NIOSH) has recognized that Noise-Induced Hearing Loss (NIHL) is the most common occupational illness in the United States. The use of heavy equipment, the drilling of rock, and the confined work environment are some of the factors that contribute to high levels of noise exposure to workers in the mining industry. Every day 80% of the nation’s miners go to work in an environment where the time weighted average (TWA) exceeds 85 dBA. Moreover, 25% of the miners are exposed to a TWA noise level that exceeds 90 dBA, the Permissible Exposure Limit (PEL). Furthermore, a NIOSH analysis of a large sample of audiograms showed that at age 50 approximately 90% of coal miners and 49% of metal/non-metal miners have a hearing impairment. By contrast, only 10% of the non-occupational-noise exposed population has a hearing impairment at age 50 (Franks, 1997) (Stephenson, 1998). Simply stated, the majority of miners have a hearing loss by the time they retire. While NIHL is the most common occupational disease in this country, this problem is especially acute among workers in the mining industry. There are several barriers to reducing NIHL in the mining industry. These include: gaps in knowledge of noise dose/source relationships, the unavailability of effective noise controls, and needs for worker education and worker empowerment. A related issue is the difficulty of communication in noisy workplaces by both hearing impaired and normal hearing workers. The Pittsburgh Research Laboratory (PRL) at NIOSH has strategically developed a hearing loss prevention program for overcoming these respective barriers in an attempt to reduce NIHL in the mining industry. This paper provides an overview of the research program being conducted at the PRL.