Search Documents

By E. Pothas, P. R. Jochens, L. B. McRae, D. D. Howat

Discussion H. J. S. Kriek*: During 1956 Iscor became interested in the acid smelting in a blast furnace of siliceous ores containing 15 per cent silica. This interest was as a result of the successful acid smelting in Germany at a CaO/SiO2-ratio of between 0.4 and 0.8. Acid smelting can become an economic proposition due to a reduction in slag volume accompanied by a lowering of the coke rate. Paschke and Hannel1 found that a free flowing slag (i.e. viscosities of less than two poise) would not be obtained at C/S-ratios lower than 0.82 and that the addition of 3 to 4 per cent alkalies became necessary. In titanium bearing slags it was established that maximum fluidity is obtained with 10 per cent TiO2. Acid smelting resulted in increased sulphur pickup with decreasing O/S-ratio and desulphurization with soda-ash outside the blast furnace was necessary. At Iscor Mr B. B. Segal established that, for slags with (CaO+MgO)/SiO2-ratios of 0.5, 0.6 and 0.7, the addition of alkalies and TiO2 resulted in a substantial decrease in melting point and also of viscosity. At a (CaO+ MgO)/ ratio of 0.53 the addition of 10 per cent TiO2 is as effective as the addition of 3.75 per cent alkalies. This means that a blast furnace can be run without the addition of alkalies and consequently the detrimental effect of alkalies on the lining can be avoided; also that fluid slags with 5 to 15 per cent MgO and 8 to 10 per cent Al203 can be obtained with 10 per cent TiO present. (CaO+ MgO)/SiO2-ratios smaller than 0.5 the addition of titania resulted in a decrease in melting point and also in an increase in viscosity. In ceramic crucibles the slag did not become more viscous with time but thickened appreciably when held in graphite crucibles. No titanium carbonitride could be detected and only Ti20a was found. Prof Howat also did not obtain the TiC-TiN solid solution and therefore it appears that the thickening of the slag is not solely due to the formation of the titanium carbonitrides. This is in agreement with the work of Michailov and Belyakova2 who found that TiO2 decreased the viscosity of acid slags and increased the viscosity of basic slags; that titanium sesquioxide (Ti203) and titanium monoxide (TiO) increased the viscosity of both acid and basic slags and that titanium carbide, which is found in larger amounts in basic slags than in acid slags, considerably increases the viscosity of both acid and basic slags. Patzak et al3 describes the following oxygen deficient titanias, viz Ti2O, TiO, Ti203, Ti3O5, Ti4O7, Ti5O9, Ti6O11- Ti10O9,Ti7O13,Ti8O15 and Ti9O17. Until about 1959 a fair amount of data was available on the viscosity of normal slags to which titania was added2, 4, 5, 6, 7, 8, 9. At Iscor an electromagnetic viscometer based on the viscometer developed by Bockris10 was built. Progress was very slow as our main attention was centred around problems associated with the operation of the Rotor process. During 1962 and 1963 two papers containing fundamental work on the viscosities of slags in the systems CaO-SiO2-TiO211 and CaO-SiO2-TiO2 at 0 per cent A1203, 10 per cent Al203 and 20 per cent Al20312 appeared. The work of Ross and Ohno obviated the necessity of any further work by Iscor on the viscosity of blast furnace slags containing titania. Ross gave the following optimum compositions for blast furnace slags containing titania. Titania % Lime % Silica % Lime/Silica-ratio 20 30-42 38-50 0.6-1.10 30 27-36 34-43 0.63-1.06 40 24-32 28-36 0.66-1.14 The optimum temperature is 1,500°C because at this temperature the largest workable composition range exists. Higher temperatures result in narrower optimum composition ranges and in increased rates of thickening. The factors affecting the rate of thickening were also investigated by Ross and Ohno, as the main problem with slags containing titania is not finding compositions which are fluid at operating temperatures but the thickening due to a lack of oxygen. With these slags when there is insufficient oxygen to co-ordinate each silicon atom with its own individual shell of four oxygen ions, some sharing of oxygen ions must occur, resulting in the formation of large silicate ions and a rise in viscosity. The formation of oxygen deficient titania can be prevented as long as iron oxide or manganese oxide remain in the liquid slag. Iwase13 and also Viens, Camp bell and Rogers14 obtained in the experimental smelting of ilmenite ores fluid slags with more than 3 to 5 per cent manganese oxide and ferrous oxide in the slags. It appears that titaniferous ores can be smelted in blast furnaces under the following conditions: (1) Acid slag operation, i.e. at C/S-ratios from O.6-1.0. (2) Dolomite can be used as a flux as MgO is a network modifier. (3) The Al2O3-content must be less than 15 per cent as alumina promotes thickening of the slag and decreases the optimum composition range. (4) The hearth temperature must not exceed 1,500°C. According to Ross a definite amount of energy is required for each ton of iron produced and in order to increase production an increase in heat

Jan 6, 1969

By F. J. N. Bruwer, T. R. Stacey

The research described considers whether the variability in coal material strength, as derived through a series of uniaxial compressive strength (UCS) tests, could be used to indicate the variability in coal pillar strength. The aim is to be able to use a distribution of UCS tests as input into the coal pillar strength calculation. This will allow the pillar design to be expressed in terms of a probability of failure rather than as the commonly used safety factor. To achieve this, the bulk strength factor associated with commonly used pillar strength formulae was replaced with a distribution of UCS results divided by an adjustment factor. The factor was determined so as to ensure that the resulting bulk strength does not deviate from the statistically determined bulk strength published in the original formulae. This approach enabled pillar strength distributions to be obtained using industry-accepted strength formulae, subsequently allowing for a probability of failure to be calculated for a specific pillar design. Using a regional coal material strength curve as a baseline, coalfields in which the coal is stronger than the regional mean can be identified and the pillar designs optimized. This is based on the stronger coals achieving lower probabilities of failure at similar safety factors. The research has considered actual UCS data from multiple mines in the Mpumalanga coalfields of South Africa, and has proved that the variability in material strength between coalfields could allow for some optimization using the proposed approach. Based on the data used in the study, a 2.78% increase in extraction could be achieved. However, further research will be required to validate the results of the study in an underground environment.

May 3, 2023

By M. Borowski, N. Szlazak, D. Obracaj

Methods of research and control of the intensity of gas inflow to undersoil layers, after the mines were abandoned are presented in the paper. Gas migration causes them to penetrate to lower storeys of buildings and earthen structures being a menace to people's health and life. The results of measurements of gas concentration in undersoil layers, gas emission to atmosphere and their accumulation in buildings on the territory of closed down mines are presented.

Jan 1, 2003

By A. Adeli, A. V. Metcalfe, E. Addo, E. Sepulveda

"The accurate modelling of geometallurgical data can significantly improve decision-making and help optimize mining operations. This case study compares models for predicting copper recovery from three indirect test measurements that are typically available, to avoid the cost of direct measurement of recovery. Geometallurgical data from 930 drill core samples, with an average length of 19 m, from an orebody in South America have been analysed. The data includes copper recovery and the results of three other tests: Bond mill index test; resistance to abrasion and breakage index; and semi-autogenous grinding power index test. A genetic algorithm is used to impute missing data at some locations so as to make use of all 930 samples. The distribution of the variables is modelled with D-vine copula and predictions of copper recovery are compared with those from regressions fitted by ordinary least squares and generalized least squares. The D-vine copula model had the least mean absolute error. IntroductionIn this paper we compare the use of D-vine copula, generalized least squares (GLS), and ordinary least squares (OLS) for modelling geometallurgical data from an orebody in South America. The first objective is to construct models for predicting copper recovery (Rec) from the Bond mill index test (BWi); resistance to abrasion and breakage index (A*b); and semi-autogenous grinding (SAG) power index test (Spi). This involves fitting a D-vine copula and regression models fitted by OLS and GLS. The second objective is to investigate the performance of the fitted models for predicting Rec (Willmott and Matsuura 2005).Traditional resource model approaches either ignore the mineral processing characteristics of extracted tonnages or treat processing as an independent component of a mining operation. The net present value (or any other objective) can be truly optimized only by considering the mining operation as an integrated system in which net value is defined as the end-product that the company sells. This approach requires the resource model to be extended to include all relevant rock properties and processing responses."

Mar 1, 2019

By H. P. Kritzinger, T. C. Kingsley

Rotary kilns are used for a variety of mineral processing operations. Hatch makes use of a kiln model developed from first principles to evaluate designs for its clients. This tool has been applied to a variety of pyrometallurgical applications. This paper illustrates the application of numerical optimization techniques in combination with the kiln model in the interrogation of a generic iron-ore reduction process. The fundamental modelling concepts are explained, followed by a description of the optimization approach. The results show how the combination of the two methods, with modern computing power, can generate a large number of viable design and operating candidates.

Jan 1, 2014

By M. Mbonami, R. Pretorius, J. Miller, P. Kyony, B. Nel, N. Mautsa

Challenges due to the formation of stable froth in acid leach systems is common at many copper and Ccbalt producers. Stable froth affects downstream process, critical equipment, and operational parameters. In severe cases the froth present safety and environmental risks and increased operational costs. Solids reports in the pregnant leach solution, accumulates, and clogs launders resulting in a potential costly safety and environmental risk. Solvent extraction is operationally affected by crud formation, organic solvent and extractant losses, reduced mass transfer due to the solids carried downstream. This article reviews the generally inadequate mechanical and hydraulic solutions of froth elimination employed over the years. The recent introduction of a chemically based solution able to eliminate froth problems that can potentially turn around the situation for those who adopt the technology.

Jan 1, 2023

By J. Sjöberg, T. Savilahti, S. B. Umar

"Sublevel caving in Malmberget mine results in mining-induced surface deformation. One of the currently mined orebodies is the Printzsköld orebody. As mining deepens there is need to assess the behaviour of the cave formed in the subsurface above this orebody. Numerical analysis was used to assess the effects of extraction to deeper levels and perform strength parametric studies. Stress redistribution was studied, and the results showed high stress buildups in the hangingwall and the crown pillar. Two failure mechanisms have been identified – shear and tensile. Reducing cohesion by 50% increased the area of the yielded zone by more than 100% in the hangingwall.IntroductionThe Malmberget mine is owned and operated by the Luossavaara-Kiirunavaara AB (LKAB) mining company. Iron ore is extracted by large-scale sublevel caving. The mine comprises a total of 20 orebodies, about 10 of which are in production today (Figure 1). The mine is located in the municipality of Gallivare, about 100 km north of the Arctic Circle (Figure 2).Successful sublevel caving requires progressive caving of the orebody after initial blasting. This results in caving of the hangingwall, sometimes all the way to surface, resulting in surface deformation. As mining progresses to deeper levels a larger area is affected by deformation. Over the years, extraction from the Malmberget orebodies has led to deformation of the ground surface, affecting residential areas and existing infrastructure.Forecasting the caving process is not straightforward as it can be rapid or slow, depending on the rock mass conditions, stress conditions, the failure mechanisms at work, etc. Moreover, several of the orebodies in Malmberget are non-daylighting, which makes reliable caving analysis even more difficult, primarily since there is less available experience from such cases. The present study was designed to improve the understanding of the caving and deformation mechanisms at Malmberget, and in particularly for the Printzskold orebody"

Jan 1, 2017

By L. Scott, M. A. Goncalves

Effective communication is a sought-after non-technical skill in the health, safety, and environmental (HSE) function and is fundamental in achieving an organization’s safety objectives. While different channels are used to communicate HSE matters, many organizations employ posters, videos, and/ or signs containing images to convey information. Communication through signage and graphical hazard symbols has been regulated in standards, but vast sections of HSE communication are bespoke communications and exist outside the sphere of standards. Effective HSE communication through images requires an understanding of the organizational culture in which the images will be used, as well as an understanding of the semiotics of the images themselves. Creative interpretation within HSE communication can create situations where the message that was received is not the message that was intended, leading to confusion and misinterpretation. This paper is aimed at elucidating the semiotics of South African HSE visual content. It was found that the indexical mode of images was most preferred in visual communication, and text-only designs the least preferred. Senders and receivers of messages differ in their opinions on the complexity of HSE communication.

Feb 2, 2021

By G. van Aswegen, J. D. Bosman

Gold bearing deposits in the Witwatersrand consist predominantly of narrow tabular conglomerates with quartzite host rock. Extensive mining of these deposits at depth results in significant stresses being induced in the periphery of the tabular excavations. Where remnant pillars are created excessive stresses have resulted in the dynamic failure of the abutments. At the Hartebeestfontein Mine four brittle shear zones have recently been exposed and investigated. For most part, they represent abutment failure into the weaker hangingwall strata, striking parallel to the abutment, dipping towards the stope, with a sense of displacement consistent with closure of the stope from above. These shear zones are similar to those described in various publications by Ortlepp2: they are essentially brittle shear zones characterised by the presence of very finely comminuted ‘rock flour’ on an obviously freshly sheared surface. The angle between the shear zone wall and extension fractures indicate the sense of shear and the intersection of the extension fractures with the shear zone walls define a strong lineation normal to the direction of slip. It is suggested that these structures are referred to as ‘mining induced dynamic brittle shears’. Les gisements d’or du Witwatersrand consistent principalement de conglomérats tabulaires peu épais contenus dans une quartzite mère. Une exploitation poussée de ces gisements en profondeur a pour résultat l’apparition d’importantes contraintes induites à la périphérie des excavations tabulaires. Là où des piliers restants sont créés, des contraintes excessives ont eu pour résultat une rupture dynamique des appuis. Dans la Mine d’Hartebeestfontein, quatre zones fragiles de cisaillement ont été récemment exposées et étudiées. Dans la plupart des cas, elles représentent une rupture des appuis dans les strates moins solides de la paroi suspendue, orientée parallèlement à l’appui, inclinée en direction du chantier d’abattage avec une direction de mouvement consistante avec l’affaissement du toit de la galerie d’abattage. Ces zones de cisaillement sont similaires à celles décrites par Ortlepp2 dans diverses publications: Ce sont essentiellement des zones cisaillement fragiles caractérisées par la présence de « farine de roche » très finement réduite sur une surface évidemment fraîchement cisaillée. L’angle entre la paroi de la zone de cisaillement et les fractures de tension indiquent le sens du cisaillement et l’intersection des fractures de tension avec les parois de la zone de cisaillement définit une forte délinéation perpendiculaire à la direction du glissement. Il est suggéré que l’on se réfère à de telles structures comme des « cisaillements dynamiques fragiles induits par l‘exploitation ». Goldablagerungen im Witwatersrand bestehen überwiegend aus schmalen tabularen Konglomeraten mit Quarzitwirtgestein. Der umfangreiche Abbau dieser Ablagerungen in der Tiefe resultiert in signifikanten Drücken, die auf die Peripherie der tabularen Aushöhlungen wirken. Wo Restpfeiler hergestellt wurden, resultierten exzessive Drücke im dynamischen Versagen der Auflager. In der Hartebeestfontein Grube wurden kürzlich vier spröde Scherzonen freigelegt und untersucht. Zum größten Teil representieren sie Auflagerversagen im Stratum der schwächeren Stollenfirste, parallel zum Auflager verlaufend, in Richtung Abbaustelle abfallend, mit einem gewissen Grad an Verschiebung konsistent mit der Schliessung der Strosse von oben. Diese Scherzonen sind jenen ähnlich, die in den verschiedenen Publikationen von Ortlepp2 beschrieben werden: sie sind im Wesentlichen spröde Scherzonen, charakterisiert durch das Vorhandensein des sehr fein pulverisierten „Gesteinsmehls“ auf einer offensichtlich frisch abgescherten Oberfläche. Der Winkel zwischen der Scherzonenwand und den Bruchverlängerungen deutet die Richtung der Scherung an und die Kreuzung der Bruchverlängerungen mit der Abscherzone grenzt sich gegen eine starke Lineation normal zur Richtung der Lehne ab. Es wird vorgeschlagen, daß diese Strukturen als `vom Abbau verursachte dynamisch spröde Scherungen’ bezeichnet werden.

Jan 1, 2003

By K. Barani, S. M. S. Ganji

Creatine was used as a lixiviant for gold dissolution from gold ore. The effects of creatine concentration, temperature, leach time, and pH were examined for their influence on extent of gold dissolution. The results show that at a temperature of 75°C and pH 11.5, gold dissolution increased from 51% to 88% on increasing creatine concentration from 25 to 50 g/t. Further increase in creatine concentration showed a negative effect on the gold dissolution. Gold dissolution increased from 47% to 87% by increasing the temperature from 25°C to 55°C, and from 61% to 89% by increasing pH from 10 to 11.5. Under the optimum conditions of solids’ content of 30%, pH 11.5, creatine concentration of 100 g/t, temperature of 75°C, and hydrogen peroxide addition of 2%, about 90% of the gold could be dissolved from the ore after 24 h. A comparison between creatine and cyanide leaching showed that 90% gold dissolution was achieved at a cyanide concentration of 300 g/t, which is three times higher than the creatine concentration under optimal conditions.

Apr 14, 2024

By S. Combrink, N. Naude

Hydrocyclones are widely used in wet mineral classification applications and can be notoriously prone to wear. The methods currently used for quantifying hydrocyclone wear profiles are mostly twodimensional. In this paper it was attempted to quantify and monitor wear in three-dimensions, using a micro-CT scanner (Nikon XTH 225 ST). Hydrocyclone wear and, more specifically, spigot wear was investigated on a Multotec HC250 (Dc 250 mm, barrel diameter) hydrocyclone. The hydrocyclone is lined by a vulcanised natural rubber compound within a metal shell, with a thermosetting polyurethane spigot and vortex finder. Tests were conducted on the hydrocyclone in a pilot-scale recirculating test setup. The wear rate of the spigot was quantified by measuring the volume change within the spigot over 122 days in operation, using the micro-CT scanner. After 122 days in operation (recirculating feed materials) the wear in the hydrocyclone led to only a 13.67% loss of spigot volume. The relatively low wear rate could be related to the fact that material recirculation led to particle smoothing and a reduction in size, thereby decreasing the wear rate. This also shows the enormous influence that particle shape and size have on wear. The research was conducted with the support of Multotec, NECSA and the University of Pretoria. Keywords: Wear, hydrocyclone, micro-CT

Jan 1, 2020

By B. Besa, S. Nalukui

Globally, the demand for mineral products is ever increasing. Extraction of these mineral resources results in the continuous production of a huge volume of waste material, including tailing dumps. The mass of tailings usually exceeds the actual resource and often contains hazardous contaminants. This study investigated the effects of tailings disposal on soil, water, and air quality in the Nampundwe area. Water, soil, and dust samples were collected from different locations in the surrounding communities. The constituents analysed in the samples included copper, cobalt, iron, sulfate, and silica. According to the results obtained, some seepages occurred from the tailings impoundment to the shallow aquifer in the area. However, the general water quality meets the Zambia Environmental Management Agency (ZEMA) statutory limits. Recorded concentrations of sulfate (1500 mg/l), copper (1.5 mg/l), cobalt (1.0 mg/l), iron (2.0 mg/l), and silica were between 0.003 mg/l and 705 mg/l, which is far below ZEMA’s statutory limit. Silica concentration was also evident in the air. The highest concentration recorded was 260 ppcc (particle per cubic centimeter) recorded in July 2019 from the northern direction of the tailings dam. The concentration was below the statutory limit of 350 ppcc. The topsoil from the northern part of the tailings recorded a silica dust concentration of 39.9 ppcc. Iron was evident in the underground soil with a concentration of 8.01 ppcc, cobalt 0.005 ppcc, copper 0.051 ppcc, while sulfate was recorded as 0.41 ppcc.

Oct 9, 2024

By D. F. Malan, P. M. Couto

We propose a layout design for the UG2 Reef where weak geological alteration layers are present. The collapse of the Everest platinum mine in South Africa indicated that these layers substantially weaken the pillars. The popular Hedley and Grant pillar strength formula cannot be used where these alteration layers are present. Underground investigations at Everest mine and numerical modelling of the layout were conducted using the TEXAN code and a limit equilibrium model. Simulations of a collapsed area and an intact area allowed for a preliminary calibration of the model. This was subsequently used to explore modified layouts for these ground conditions. An alternative is to compartmentalize the blocks of ore using barrier pillars. The numerical modelling predicted that the barrier pillars appear to remain stable even in the case of large-scale collapses, provided their width exceeds 25 m. Main access routes into the mine can be protected by a double row of pillars at least 15 m wide to provide a safe travelling way. As a cautionary note, these conclusions are based on the model calibration and this needs to be refined in future. Calibration of the limit equilibrium model remains a challenge owing to the large number of parameters involved.

May 3, 2023

By D. A. Cowen

Toll and custom treatment of base metal concentrates have been performed for decades as mines and concentrators are developed distant from capital and, energy-intensive smelting and refining facilities. Commercial treatment terms have been developed and refined for over a century, and are negotiated taking into account a complex array of quality and economic factors. Treatment of third-party concentrates in the South African platinum industry is a comparatively recent development, brought about by the opening up of mineral rights and operations being developed that are smaller than the critical size required to sustain capitalization of smelting or refining plant. Published commercial terms have not been demonstrated to reflect the complexities and subtleties of base metal concentrate markets. This paper outlines some key elements and parameter ranges of base metal concentrate treatment contracts, and applies similar principles to typical Merensky and UG2 platinum group element (PGE) concentrates to determine potential value distribution between the mining and treatment parties in tolling arrangements.

Jan 1, 2012

By Y. P. Shoupletsov

ABSTRACT. A retrospective analysis of some geomechanical classifications for rock masses is presented. It is shown that estimates of rock mass strength according to geomechanical classifications developed, e.g., for construction of tunnels and for ore mines can differ very much. Development of specifically oriented classifications for rock masses with certain geomechanical properties is required. ZUSAMMENFASSUNG. Es wurde eine retrospektive Analyse einiger geomechanoschen Klassifikationen von Gesteinsmassiven durchgefuhrt. Es idt aufgezeigt worden, dass die Bes-timmung der Festigkeit des Massivs nach geomechanischen Klassifikationen, die z.B. fur den Bau von Tunnelen und fur Erzbergwerke entwickelt wurden, sich um etliche Male unterscheiden kann. Es ist eine Entwicklung von spezialisierten Klassifikationen fur Gesteinsmassive mit bestimmten geomechanischen Eigenschaften erforderlich. RESUME. Il a ete fait l’analyse retrospective de certaines classifications geomecaniques des massifs de roche. Il a ete montre que les estimations de solidite du massif suivant les classifications geomecaniques etudiees, par exemple, pour la construction des tunnels et pour les puits de minerai peuvent differer en quelques fois. Il est donc necessaire d’etudier les classifications specialisees pour les massifs aux proprietes geomecaniques particulieres.

Jan 1, 2003

By E. Govender-Opitz, L. Lelia

The South African mining industry plays a significant role in the economy of the country. Nonetheless, the negative impacts on the environment continue to prevail. In regions where mining exists in proximity to communities, mining activities have led to the disruption of modality. Rural communities are mostly affected as they depend on land use for agriculture to sustain their livelihoods. The conversion of land for mining activities often leaves the communities vulnerable when mines close because of the limited life span of mines. An ongoing discourse focuses on how the mining industry can contribute to sustainable development of the communities in which they operate. Post-mining transformation offers an approach for the mining companies to contribute to sustainable livelihoods post-mine closure by strengthening rural-urban linkages, which ensures inclusive development of both rural and urban areas. The paper employs a case study approach to Richards Bay Minerals and the adjacent rural communities of Sokhulu and Mbonambi. It sets out to understand the post-mining transformation employed by RBM and explore the rural-urban linkages that manifest as a result. Findings show that sand dune rehabilitation employed by RBM is successful in restoring soil fertility and establishing the natural ecosystem. The casuarina planted to rehabilitate the dunes is used to spur an alternative charcoal industry post-closure. The main rural-urban linkages that manifest are flows of people due to job opportunities and flows of goods from the sale of charcoal produced. However, there is a lack of communication and lack of authority to ensure responsible management of the casuarina plantation and equitable sharing of benefits. The paper recommends that other post-mining transformation strategies such as eco-tourism should be explored and that the government, at both national and local level, the community and the mine should be involved to ensure overall success and sustainability of the strategy. Keywords Post-mining transformation, rural-urban linkages, alternative land use

Jan 1, 2020

By J. Fu

"Since it was first identified in 1817, selenium has received considerable interest. Native selenium and a few selenium minerals were discovered several decades later. With the increasing number of selenium minerals, the occurrence of selenium minerals became the focus of much research. A great number of selenium deposits were reported all over the world, although few independent selenium deposits were discovered. Selenium is obtained mainly as a byproduct of other metals, and is produced primarily from the anode mud of copper refineries. This paper presents a comprehensive review of selenium minerals, as well as the treatment of copper refinery anode slimes for the recovery of selenium. Our focus is on the selenium minerals, including their discovery and occurrence, and the distribution of selenium resources. In addition, the main methods of recovering selenium from copper anode slimes are summarized. IntroductionSelenium (Se) was first observed in 1817 in a laboratory (Greenwood et al., 1984). The discovery of selenium was made by the Swedish chemist J.J. Berzelius and J.G. Gahn, who isolated selenium from a red residue in sulphuric acid from pyrite mined at Fahlun, Sweden. Selenium was named from the Greek word selene (moon), since it resembled tellurium, which had been discovered a few years earlier and named from the Latin word tellus (Earth).After the first observation of selenium in the laboratory, selenium received considerable interest. In 1954, E.P. Kaiser pointed out that Se is enriched in sulphide ores and often associated with Bi, Co, Sn etc. (Kaiser 1954). In 1959, Hawley and Nichol investigated selenium in Canadian sulphide minerals, and presented the content of selenium in sulphide from several deposits of different types. They also proposed that Se is enriched in lowtemperature hydrothermal pyrite (Hawley and Nichol, 1959). The thermodynamic conditions for forming native selenium and selenium minerals in sedimentary rocks were discussed, as well as geochemical behaviour of selenium near the oxidation zones of sulphides in the 1970s (Howard III, 1977; Zhu et al., 2003). Zhu et al. examined the morphology, features, and genesis of native selenium from Yutangba, Enshi City, Hubei Province, China in 2004, and pointed out, from the different forms of native Se, that selenium can be activated,transformed, remobilized, and enriched at sites such as in the unsaturated subsurface zone or in the saturated zone (Zhu et al., 2005). The transport and deposition of selenium in felsic volcanic-hosted massive sulphide deposits of the Yukon Territory, Canada was studied and reported by Layton- Matthews et al. (2005)."

Jan 1, 2016

Numbering of the Journal Because computer and library authorities prefer journal subscriptions to be based on the calendar year, and because the present numbering system of the Journal of the South African Institute of Mining and Metallurgy does not conform with the calendar year, it has been decided to change the numbering system of the Journal.

Jan 1, 1979

By L. Godfrey, Z. Nontso, F. Magweregwede, B. Maphalala, S. Khan

The aim of this paper was to establish if mineral resource scarcity is a driver for South Africa to transition to a circular economy. The project objectives were achieved by investigating economically viable, and critical or strategic minerals remaining in South Africa, as well as resource scarcity, as a driver for South Africa to transition to a circular economy. The study found that some minerals in South Africa, such as iron ore, lead, manganese, gold, and cobalt have less than 50 years of economically viable mining remaining. At least 18 minerals can be classified indicatively as critical or strategic: aggregates, bauxite, chromite, cobalt, copper, gold, graphite, iron, limestone, lithium, manganese, nickel, phosphorous, platinum group metals, rare earth elements, silver, titanium, and vanadium. The classification was based on the minerals’ economic importance, supply risk, and potential use in the development and manufacturing of emerging technologies. The findings suggest that the scarcity of mineral resources is a critical driver for the country to transition to a circular economy. Other identified drivers include socio-economic factors, climate change commitments, and business objectives. All minerals are non-renewable resources and at risk of depletion, therefore sustainable extraction and use are critical. Priority should be directed at investigating circular economy opportunities and substitutes for commodities at risk of being depleted within the next 50 years. There is an opportunity for South Africa to transition from a minerals export-based model to one that promotes local mineral beneficiation and manufacturing of end products.

Mar 5, 2025

By A. Mabentsela

A furnace freeze lining is necessary for safety and economic reasons in several smelting operations. The integrity of the freeze lining is put at risk by furnace power imbalances. Although numerous models have been derived to model the growth and depletion of the freeze lining due to power imbalances, no model exists for thermomechanical damage to the freeze lining. This study provides an initial pathway for modelling thermomechanical damage to the freeze lining in an ilmenite smelting furnace using information from the literature and experimental work. A methodology under the framework of continuum damage mechanics is proposed to model mechanical damage to the freeze lining due to phase changes, thermophysical changes, and constrained thermal expansion. Drill cores of solidified slag ingots were used to represent the freeze lining. The modified power law proved to be the best predictor of the softening response of the drill cores. Damage driving parameters were extracted from the raw data, and governing equations of the parameters with respect to temperature were derived for use in a finite element method (FEM) code.

Jan 26, 2023