Search Documents

By A E. Paterson

General aluminium corrosion charts based on 1100 alloy listing product and temperature have been developed by AFSA, mainly from available sources. The categories of corrosion expectation are fairly wide. As a result the charts are more useful in indicating what is not suited as distinct from what is. The question of how to develop useful information is assessed. Having discarded improbable options one is left with the need to refine the possible. Within each alloy group corrosion potential differs. From an engineering application point of view, the corrosion resisting marine alloys, the 5xxx series show increasing corrosion as the percentage of Magnesium increases. An important issue is that as the welding filler used for 5xxx series is Mg rich (to avoid hot cracking), the filler is likely to show the weakest resistance. In addition, when subjected to fatigue loading, the preference for critical joints is to dress the joint to the level of the base material. Overheating of the weld extends the HAZ zone and weakens the material as Mg moves to the grain boundaries. Indicator chart refinement approaches suited to aluminium use in commercial transport are discussed.

Jan 1, 2006

By H. Han, Z. Gao, Y. Gao, W. Sun, J. Wang

Strategic Ca-bearing minerals like scheelite and fluorite are usually separated by flotation, yet the separation is quite difficult due to their similar surface Ca active sites. Compared with the conventional strong collector sodium oleate (NaOL), lead nitrate-benzohydroxamic acid (Pb-BHA), complex collector shows a better selectivity for scheelite, yet its high cost hinders its wide application. Therefore, a novel collector (Pb-BHA-NaOL complex) was initially developed in this work to overcome the abovementioned dilemma. The flotation results of a single mineral showed that Pb-BHA-NaOL had a better selectivity for scheelite than Pb-BHA. Under the conditions of sequential assembly of Pb, BHA and NaOL at the molar ratio of 240:120:1 and pH 9.0, selective separation of scheelite from fluorite could be achieved without adding any depressants. In addition, for the same preferred scheelite recovery, Pb- BHA-NaOL could also save approximately 20% Pb and BHA compared with Pb-BHA. The analyses of the zeta potential measurement and X-ray photoelectron spectroscopy indicated that Pb-BHA-NaOL showed stronger adsorption on scheelite relative to fluorite. Meanwhile, Pb-BHA-NaOL showed more adsorption modes and higher utilisation of Pb and BHA on scheelite than Pb-BHA, which was due to the accelerator, NaOL. Keywords: Scheelite, fluorite, lead nitrate, benzohydroxamic acid, sodium oleate, flotation

Jan 1, 2020

Council and Standing Committees, 1978-1979 President: Dr M. G. Atmore. Vice-Presidents: D. A. Viljoen and Dr P. R. Jochens. Honorary Treasurer: J. K. E. Douglas. Immediate Past President: P. A. von Wielligh. Members of Council: J. D. Austin, A. N. Brown, H. E. James, Prof. R. P. King, Dr D. G. Krige, Prof. F. Q. P. Leiding, D. G. Malan, C. S. McPhail, J. C. Mostert, G. Y. Nisbet, H. G. M. Rose, W. T. Ruhmer, G. C. Thompson, R. A. von Maltitz. Chairman, Witbank-Middelburg Branch: T. S. Wilmot. Chairman, Orange Free State-Klerksdorp Branch: H. M. W. Eschenburg. Past Presidents Serving on Council: R. J. Adamson, H. Britten, J. K. E. Douglas, Prof. D. D. Howat, Dr J. P. Hugo, D. G. Maxwell, Prof. R. P. Plewman, Dr R. E. Robinson, Dr M. D. G. Salamon, P. W. J. van Rensburg. Standing Committee Chairmen: Membership, Dr P. R. Jochens ; Technical Programme - Metallurgy, Prof. R. P. King ; Technical Programme - Mining, H. G. M. Rose; Vacation School - Metallurgy, J. C. Mostert; Vacation School - Mining, D. G. Malan/J. D. Austin; Awards, P. A. von Wielligh; Excursions, D. A. Viljoen; Adjudication, P. A. von Wielligh; Constitution, Rules and Policy, P. A. von Wielligh; Monograph Series, Dr R. E. Robinson; Professional and Technician Train¬ing Committee, Dr M. D. G. Salamon; Career Guidance, D. G. Malan; Phoenix National Committee, Dr R. E. Robinson; 1982 World Congress, Dr M. G. Atmore; Witbank Coal Colloquium, Dr P. R. Jochens; Mines and Works, P. A. von Wielligh.

Jan 1, 1979

By D. -X. Li

The paper covers many literature reports of processes using nitrogenous species as an oxidant for processing refractory gold ores, especially development in the pretreatment of refractory gold minerals by nitric acid. These processes include the high-pressure and the atmospheric-pressure oxidation methods. High-pressure oxidation processes are difficult to carry out, because they require high-capital cost autoclaves. Atmospheric-pressure oxidation processes are easier to manipulate, but complete absorption and reuse of NOx is difficult or multiple-stage absorption must be established for its reuse. So, some new methods were developed, such as catalytically oxidizing technology of NOx to allow subsequent recovery of gold. Keywords: nitric acid; pretreatment; refractory gold

Jan 1, 2009

By C. B. Carelse, M. Manuel, D. Chetty

Automated mineralogical analysis of platinum group minerals (PGM), using the mineral liberation analyser, provides information used to understand flotation efficiency, primarily from a PGM liberation and association standpoint. To date, however, there is no consistent understanding regarding PGM speciation and its impact on floatability. Previous studies of PGM from UG2 ores concluded that a larger dataset is needed from which the various parameters can be modelled. Parameters on telluride, arsenide, sulfurarsenide and alloy species need to be integrated to fully understand the impact of PGM speciation on flotation, and for this, ores other than PGE-sulfide-rich UG2 must be assessed. Flotation rougher rate tests were performed on feed samples from two Platreef ores to determine the flotation response of individual liberated PGM species. This was achieved through automated mineralogical analysis of feed, rougher concentrates and tails. Based on 1529 liberated PGM grains assessed over the circuit for two Platreef ores, preliminary results show that PGM speciation, species grain size and competition from gangue appear to influence floatability in an ‘optimised’ laboratory environment. Keywords: PGM, PGM species, flotation, liberation

Jan 1, 2020

By L. A. Cisternas, A. Lopez-Valdivieso, Y. L. Botero, L. Cortes

In the processing of sulfidic ores, pyrite is usually depressed and ends up in the tailings. However, pyrite is the most common species responsible for acid mine drainage (AMD) due to its spontaneous oxidation. This AMD affects the tailing chemical stability by dissolving some toxic or heavy metals species such as As, Cd, Co, Pb, and Zn, which can migrate into the surrounding ecosystems. Therefore, the strategies to reduce pyrite’s environmental impacts are a crucial point to produce more chemically stable tailings. Consequently, numerous studies have been made to find procedures that could inhibit or restrain AMD. This work aims to develop a procedure for designing conceptual flotation circuits that can produce tailings with low content of pyrite and to assess this type of circuit with traditional flotation circuits. The method consists of applying optimal flotation design where three products are considered: metal concentrate, pyrite concentrate, and tailing with low content of pyrite. Two approaches are considered; in the first, a flotation circuit is designed to generate a concentrate rich in all sulfide minerals and to obtain a tail with low pyrite content. Then, a second flotation circuit is designed for the selective separation of the bulk into metal concentrate and pyrite concentrate. This is called fractional separation design. In the second approach, a flotation circuit design is realised that generate the three products simultaneously. This is called integrated separation design. Both fractional separation design and integrated separation design are assessed in this paper. This methodology is focused on cleaner production (waste prevention and resource minimisation) rather than end-of-pipe technology (treat existing waste). The methodology was applied to a copper sulfide ore from a local company in the Antofagasta region (Chile). This ore contains chalcocite, covellite, iron oxides, and pyrite. Keywords: Flotation, tailing, pyrite, cleaner production

Jan 1, 2020

By D White, L. Lorenzen

Sampling and metallurgical testwork during various phases of engineering studies is of paramount importance for a robust processing plant design. When developing a process flowsheet, risks in achieving desirable financial outcomes are minimised by ensuring that appropriate sampling and adequate metallurgical testwork support the engineering and cost estimation at each phase of project development. The quality and type of samples used for metallurgical testwork are just as important as the metallurgical testwork itself. The key characteristic required of any sample is that it represents some defined portion of a mineral deposit. Representivity should consider the spatial orientation, lithology, alteration, degree of oxidation, mineralogy, and competency of the ore such as hardness and abrasiveness. Statistically representative sampling procedures and an appropriate metallurgical testwork program should be designed to bring metallurgical understanding up to feasibility study standard and to give a basis for process plant design. The authors have observed that the quality of sampling and quantity of metallurgical testwork carried out during the various phases of engineering studies are often insufficient to truly support a robust plant design. Some designs are based on benchmarks of apparently similar ore bodies or rely on buoyant metal prices supporting cash flows until rectifications can be implemented. The paper will discuss important aspects of sampling and testwork required for engineering studies in designing process plants. Keywords: Sampling, metallurgical testwork, studies, design

Jan 1, 2020

By B. Kweto, W. Legodi, C. van Buuren, R. F. Sandenbergh

Biooxidation, and especially the BIOX® process, is a viable, economical and environmentally attractive process to liberate gold hosted in refractory sulfides by oxidatively leaching the sulfides as soluble sulfates. The moderate to high cyanide consumption during the subsequent cyanidiation of the washed biooxidation residue is probably caused by the retention on the solids of labile sulfur species formed during the multi-electron oxidation process of sulfide to sulfate. In this work the nature and mode of transport of the cyanicides in the products from the mesophile BIOX® process, as well as that of the combined mesophile and thermophile bioxidation process, were considered and strategies to reduce cyanide consumption evaluated. It was found that labile sulfur species were the major cyanide consumers in the mesophile biooxidation product, forming predominantly thiocyanate during cyanidation. The transfer of labile sulfur species was only marginally decreased by more intensive and thorough washing of the biooxidation products with warm and hot water, intense stirring and warm caustic leaching. A major reduction in cyanide consumption was however achieved by using a combined mesophile and thermophile biooxidation process. Keywords: Biooxidation, refractory sulfide gold ores, cyanide consumption

Jan 1, 2020

By F. Petersen, W. van Dyk, J. Bonsu, A. Isafiade

"This paper aims to demonstrate how a systemic approach can be applied to the analysis of the causes of accidents in South African mines. The accident analysis framework used was developed previously by the authors from the combination of the Mark III version of the Swiss Cheese model, Incident Cause Analysis Method (ICAM), the Nertney Wheel model, and safety management principles. Data on 91 accidents occurring from 2010 to 2012 at the site of a platinum mine in South Africa were used to populate the newly developed framework. The results obtained show that while routine violations (45% of all accidents analysed) were the most common form of human error, problems in the physical environment of workers were the most common workplace factor (39.6% of all accidents analysed). Furthermore, inadequate leadership was found to be the most common systemic factor responsible for accidents (51.6% of all accidents analysed). Some workplace factors were more commonly associated with particular unsafe acts than others, and some systemic factors were more associated with particular workplace factors than others. The outcome of this study demonstrates that systemic factors, rather than human errors and violations, are the chief causes of accidents in the mining sector. IntroductionThe mining industry is a very important sector of the South African national economy. A major factor threatening the sustainability of this industry is mining accidents, which frequently result in injuries or deaths, destruction of property, and pollution of the environment. In the past, mining accidents have led to the shutdown and threat of shutdown of mines (Ryan, 2008; Mail and Guardian, 2011). The country stands the risk of incurring significant losses if the mining industry continues to experience shutdowns. In 2012, the mining sector accounted for R262.7 billion (equivalent to US$32.83 billion) representing 8.3% of GDP directly, on a nominal basis (Chamber of Mines of South Africa, 2013).Mining safety is a global concern and has attracted significant international attention. This has precipitated various studies into different aspects of mining. Unfortunately, human error has been blamed for the majority of these accidents. A study by the US Bureau of Mines found that human error is the cause of almost 85% of all accidents (Patterson and Shappell, 2008). In Australia, it is the cause of two out of every three occupational accidents (Patterson and Shappell, 2008). Various mining companies maintain that they run efficient systems, and hence the behavioural problems of workers are to blame for most accidents. An understanding of accident causality could be a major step in the quest to reduce accidents. Only with a good understanding of the accident process can effective remedies can be designed."

Jan 1, 2017

By B. Hayen

The principal advantages of fibre optics as compared to copper wire are well known and include almost perfect electromagnetic isolation, light weight, small size, excellent transmission security and substantially better bandwidth/distance performance. The decreasing cost of the optical fibre technology (both fibre cable and equipment) has led to another generation of private networks, which provide much larger bandwidths, very high reliability and an increase of the maximum geographical coverage. The larger bandwidth allows to transport all types of information on a single network. Typical communication requirements are speech (audio), computer data, LAN info, control information, video, etc. OTN or ‘Open Transport Network’ is a transmission system based on the latest available technology in fibre optics. It is characterized by the dual ring approach, resulting in high network availability, and the integration of different types of services in one network. As such, it can fulfil almost all transmission requirements for voice, data, LAN, video and any special service required.

Sep 1, 2001

By Z. Yang, X. Bian

"The synthesis of 3-hydroxy-2-naphthyl hydroxamic acid (H2O5) as a collector for bastnaesite is described. The flotation performance of H2O5 with respect to bastnaesite was investigated by flotation tests, measurements of the surface adsorption capacity, and polarizing microscopy. The results indicated that H2O5 exhibits superior collecting performance compared with direct flotation recovery of bastnaesite, with recoveries above 90% at pH 8–9. The adsorption mechanism of H2O5 on bastnaesite was studied by solution chemistry analysis and ?-potential tests. The results showed that the adsorption of H2O5 is associated with the types and concentrations of hydrolysis products of rare earth cations on the bastnaesite surface. At pH 8–9, the hydrolysis-dominant components RE(OH)2+ and RE(OH)2 + of the rare earth cations were adsorbed onto the bastnaesite surfaces, which were considered to be the major positive active points and were beneficial to chemical adsorption of the reagents. The pH range of 7–10 was optimum for bastnaesite floatability, and the adsorption of H205 on bastnaesite was by means of chemical adsorption through formation of a five-membered ring chelate. IntroductionThe rare earth elements (REEs) have long been known as ‘industrial gold’ and are widely used in the petroleum, chemical, ceramic, metallurgical, and permanent magnet material industries because of their special physicochemical properties (Chen, 2011; Krishnamurthy and Guptac, 2002; Esquivel, Bohe, and Pasquevich, 2002; Abrahami, Xiao, and Yang, 2015). Demand for REEs is growing in response to continuous advances in science and technology. Currently, most REEs are extracted from bastnaesite ((Ce,La)CO3F) (Chelgani et al., 2015; Yosry, 1990), which is recovered from rare earth ores by flotation. Typically, hydroxamic acids are used as bastnaesite collectors (Xu, 2015; Ren, 1997; Mousumi and Venugopal, 2016). Research into the mechanism of interaction between hydroxamic acids and bastnaesite is important for improving the recoveries of bastnaesite. However, there have been few studies that examine this mechanism."

Jan 1, 2017

By J. Witley

"Narrow tabular platinum group element deposits in the Bushveld Complex of South Africa are typically evaluated by diamond core drilling from surface. Several short deflections are drilled from each mother hole in order to obtain multiple intersections at a close spacing (less than 1 m). Examination of the intersections from deflection drilling revealed the importance of these deflections in understanding the representivity of the borehole, obtaining an estimate of the nugget effect, and mitigating the undesirable effect of the high grade variability at the ultra-short range that is a characteristic of these deposits. The use of deflections in estimation was investigated by means of a number of techniques and scenarios in order to find the most appropriate way to use them in an estimate. A significantly improved level of confidence was gained from using multiple close-spaced intersections rather than a single borehole intersection. IntroductionThe Upper Group 2 chromitite layer (UG2 or UG2 Reef) is known for its remarkable geological continuity, being traced almost uninterrupted for tens of kilometres. However, what is often less well emphasized is the high variability in platinum group element (PGE) grade and thickness (and therefore PGE content) and internal reef stratigraphy over very short distances (several metres or even tens of centimetres).This paper examines the application of short drill-hole deflections in evaluating UG2 PGE mineral resources at Marikana in the western Bushveld Complex of South Africa."

Jan 1, 2017

Slope stability is a fundamental part of a successful mining operation. It impacts directly on the safety of personnel and the economics of the mine. The Jwaneng Mine in Botswana is planning a push back of 644m depth in the south east wall. Mining will commence in 2010 and be completed in 2024. This will put the mine in the deep pit category. The mine has invested in extensive geotechnical data gathering and design programs that started as far back as 2003 for the south east wall. The south east wail of Jwaneng Mine is characterized by foliation that dips adversely into the mining faces. The orienta1ion of the foliation is variable due to intense tectonic movements that have also caused the occurrence of faults that are sub-vertical. A considerable amount of information on the characteristics of structural patterns and the rock mass has been collected. This paper presents an overview of the feasibility level geotechnical design that is about to be concluded.

Jan 1, 2010

SYMPOSIUM ON THE RECOVERY OF PYRITE The proceedings of the Symposium on the Recovery of Pyrite, held in Johannesburg in June 1969, may be ordered from the Secretary, S.A.I.M.M., P.O. Box 61019, Marshalltown, Transvaal, at the reduced price of R5.00. Papers and addresses presented at the Symposium were: Opening Address by Mr J. K. E. Douglas (President). "The world sulphur position," by W. C. J. van Rensburg (Member). "The South African sulphur position," by D. L. Taylor (Member). "The recovery of pyrite at Government Gold Mining Areas Limited," by R. J. Westwood (Member), G. S. Stander (Affiliate) and H. P. Carlisle (Member). "Recovery of pyrite concentrates from colliery-waste discards-A preliminary assessment," by W. A. Gilbert (Visitor) and E. A. Nugent (Member). "The role of pyrite in upgrading the uranium content of Witwatersrand conglomerate ores by means of the heavy-medium separation process," by D. J. Tutt (Associate Member). "Pyrite recovery by jigs at Durban Roodepoort Deep Limited," by E. J. Dominy (Affiliate), F. Diamond (Affiliate) and A. D. Graham (Affiliate). "The storage of pyrite concentrates," by Joan C. Campkin (Visitor) and P. J. Lloyd (Member). "The flotation plants of the Anglo-Transvaal Group," by L. A. Bushell (Member). "Pyrite flotation with amines and cyanidation of the products," by E. H. D. Carman (Member). "Gold recovery by cyanidation from mill products obtained after pyrite flotation," by P. G. Mrkusic (Graduate), M. Sciarone (Visitor) and H. E. Simonsen (Visitor). "The influence of sulphydryl and cationic flotation reagents on cyanidation of native gold," by K. G. Ashurst (Visitor) and W. P. Finkelstein (Member). "Laboratory tests on the flotation of pyrite from Witwatersrand gold ores by cationic collector," by J. Levin (Member), and M. L. Veitch (Visitor). Closing Address, by Dr R. E. Robinson (Director, National Institute for Metallurgy). INCOME TAX: POST-GRADUATE STUDY COURSE CONCESSION As a result of representations made by the Associated Scientific and Technical Societies of S.A. and the Suid-Afrikaanse Akademie vir Wetenskap en Kuns, engineers and scientists will now be allowed to deduct expenses incurred on post-graduate study courses from their taxable income. The conditions of this concession are set out in section 16 of the Income Tax Act, 1969, which reads as follows: 16. (1) The following section is hereby substituted for section 16 of the principal Act: 16. "Notwithstanding the provisions of section 23(a) and (b), there shall be allowed to be deducted from the income of any person who is a dentist or medical practitioner or practises any profession referred to in paragraph (a), so much as the Secretary may allow of any expenditure incurred by such person in the circumstances contemplated in paragraph (c), if the Dental Association of South Africa in the case of a dentist, or the Medical Association of South Africa in the case of a medical practitioner, or the "Suid-Afrikaanse Akademie vir Wetenskap en Kuns" or the Associated Scientific and Technical Societies of South Africa in any other case, certifies in such form as the Secretary may prescribe that such person- (a) if he is not a dentist or medical practitioner, is the holder of a degree in engineering or allied technology or natural sciences awarded by a recognized university on completion of a prescribed minimum period of study of not less than four academic years or the equivalent thereof and enabling the holder thereof to practise the profession of an engineer or a profession for which advanced and specialised scientific knowledge is required which relates directly to- (i) the development or exploitation of natural resources; (ii) mining or prospecting for minerals; (iii) the production of pastoral, agricultural or forest produce ; (iv) the breeding or care of farm animals; (v) any industrial process; or (vi) the training of specialists in any branch of science or technology connected with any aforementioned profession; (b) has practised his profession for not less than three years; and (c) has incurred such expenditure during the year of assessment in respect of the attendance by him of any postgraduate study course approved by such body to improve his qualifications for carrying on his profession in the Republic". (2) The amendments effected by subsection (1) shall first take effect in respect of assessments for the year of assessment ending on the twenty-eighth day of February, 1970. From this section it is clear that the concession will only be granted if the application is accompanied by a certificate, which certificate must be either signed by the Chairman of Die Akademie or the President of the Associated Societies. In terms of the authority granted such certificates must certify that: (i) the taxpayer concerned has practised his profession for not less than three years; (ii) the expenditure was incurred by the taxpayer during the year of assessment indicated in the certificate; (iii) the expenditure was incurred by the taxpayer in respect of the attendance by him of a post-graduate study course approved by the Associated Scientific and Technical Societies of South Africa or Die Suid-Afrikaanse Akademie vir Wetenskap en Kuns, as the case may be, to improve his qualifications for carrying on his profession in South Africa; (iv) the taxpayer is the holder of a degree in engineering or allied technology or natural sciences, which degree was awarded by a recognized university,

By L. S. Linda, P. G. H Pistorius

Ferritic stainless steel is utilized to fabricate automotive exhaust systems using a ferritic weld metal. Ductility of the weld metal is higher if its microstructure contains a significant proportion of equiaxed grains. The formation of equiaxed (rather than columnar) grains is favoured by a higher titanium weld metal content. In this study, the Ti content of ferritic stainless steel weld metal was changed by using Tifree (Type 436) and Ti-containing (441) ferritic stainless steel as base metals. The metal-cored welding consumable contained 0.4% Ti. Gas–tungsten arc welding and gas–metal arc welding processes were compared. The weld metal Ti content ranged from zero to 0.5% Ti, as determined from scanning electron microscopy supplemented by inductively coupled plasma optical emission spectroscopy. Cross-sections of the weld beads were subjected to point counting (to estimate the fraction of equiaxed grains) and image analysis (to estimate the average grain size). Point counting proved to be more reliable. The fraction of equiaxed grains was sensitive to the Ti content, but not to the welding process. Below 0.4% Ti, the fraction of equiaxed grains gradually increased with an increase in the weld metal Ti content; above 0.4% Ti, the fraction of equiaxed grains rapidly increased with increasing Ti content. The transition in behaviour at 0.4% Ti corresponded to a Ti content at which Ti-rich precipitates became stable at the estimated liquidus temperature of the weld metal.

Jul 2, 2022

By T. Nesane, S. S. Mnyakeni-Moleele, L. C. Murulana

The effectiveness of two synthesized ionic liquids, 1-(benzyloxy)-1-oxopropan-2-aminium 4-methylbenzenesulfonate (1-BOPAMS) and 4-(benzyloxy)-4-oxobutan-1-aminium 4-methylbenzenesulfonate (4-BOBAMS), were evaluated for mild steel corrosion inhibition in 1.0 M hydro-chloric acid solution, using electrochemical impedance spectroscopy (EIS), potentiodynamic polarization (PDP), and gravimetric techniques. Organic moieties responsible for the adsorption process on mild steel surface were investigated using Fourier transform infrared spectroscopy (FTIR). Gravimetric analysis revealed that the inhibition efficiency of 1-BOPAMS and 4-BOBAMS increased with concentration, with maximum inhibition values of 90.32% and 97.91%, respectively, at the highest concentration of the inhibitors. Gibbs free energy (ΔG°ads) values indicated a strong interaction between the mild steel surface and the molecules of the ionic liquids, and that the adsorption process was spontaneous. These values also show that the inhibitive nature of ionic liquids against mild steel corrosion is caused by a mixedtype of adsorption film formed on the steel surface. The Langmuir adsorption isotherm was used to describe the adsorption of ionic liquid molecules onto the mild steel surface. Polarization curves showed that 1-BOPAMS and 4-BOBAMS have a similar effect on both the anodic and cathodic half-reactions, indicating that they prevent the dissolution of mild steel through both physical and chemical process. Nyquist plots were defined by incomplete semicircle capacitive loops, showing that the charge transfer mechanism controls the corrosion of mild steel in acidic solution.

Apr 1, 2021

By M. Z. Emad, A. Khan, N. Abbas, K. G. Li

Probability-based empirical methods were employed as an alternative approach to predicting uncertainties associated with rock mass properties. The focus was on developing probabilistic spreadsheets to forecast rock mass classification indexes. Histograms were constructed to describe the best distribution in predicting rock mass properties. The developed models also offer utility in predicting the impact of discontinuities within the rock mass on rock strength and rock mass classification systems. Statistical analyses identified volumetric joint count, joint spacing, joint frequency, and rock strength as the most influential parameters. Moreover, the statistical analysis revealed varying degrees of correlation among different rock mass properties. While some properties demonstrated significant correlations suitable for modelling, others did not align well with any correlation model. The results highlight the need for a comprehensive approach to rock mass characterization, considering multiple factors beyond volumetric joint count. Geological complexities, including tectonic activity and weathering processes, may obscure direct correlations. These results emphasize the importance of empirical modelling and detailed site investigations for accurate assessment of rock mass quality and stability in the Himalaya.

Jun 10, 2024

By J. Petersen, M. Reuter, E. Asselin, M. Becker, N. Uys

In order to meet society’s ever-increasing demand for metals and address the numerous technical, economic and environmental challenges within the current mining context, a holistic approach to process design, which is grounded in mineralogy, is needed. This would ensure that the impact of varying process mineralogy (and associated chemistry) on technical considerations and the associated economic implications and environmental consequences are taken into account upfront. This investigation focuses on the commodity zinc due to its strategic value coupled with limited resource availability and the wide variety of substantially different process technologies in existence. As the most commonly processed zinc ores contain zinc sulphides, the mineralogy/chemistry of these ores and their associated process routes will be discussed. The findings have been generated through the analysis of two case studies, Teck’s Trail Operations (British Columbia, Canada) and Hudbay Minerals’ Flin Flon Operations (Manitoba, Canada). The flotation of zinc sulphide ores to produce concentrates with varying mineralogy, represents the starting point for both case studies. The hydrometallurgical process routes for the further refining of zinc and other valuable metals include roast-leach-electrowinning (RLE), and zinc pressure leaching (ZPL). The effect of process route choices on primary metal recovery (Zn), coproduction of other base metals (Cu, Pb), potential for other valuable metal production (Ag, Au) including less well known, but increasingly important trace elements (In, Ge), and the production of other by-products (H2SO4, S0) are discussed. The economic and environmental implications of these aspects will also be considered. It is concluded that a quantitative modelling approach must be taken where waste management is integrated into process system design and simulation as a key unit operation. Keywords: Zinc Sulphide Processing; Design Decisions; Mineralogy

Jan 1, 2020

THE THIRD INTERNATIONAL GEOCHEMICAL EXPLORATION SYMPOSIUM (Summary Account) This Symposium, co-sponsored by the Canadian Institute of Mining and Metallurgy and the Society of Economic Geologists, was held in Toronto, Canada in April, 1970. Over 700 delegates attended from 26 countries. Ninety papers were presented at the symposium and another 18 papers were read by title. The programme included: An Opening Session, Five General Sessions, a session on Remote Sensing Methods, a session on Geochemical Prospecting for Petroleum and Natural Gas, a session on Primary Halos and Lithogeochemical Methods, and a session on Statistics and Evaluation of Geochemical Data. The delegates were welcomed by Dr J. M. Harrison, President of the Canadian Institute of Mining and Metallurgy and Dr C. H. Smith, Regional Vice-President, North America of the Society of Economic Geologists. Dr D. R. Derry of Toronto delivered the opening address to the Symposium entitled 'Geochemistry-the link between ore genesis and exploration'. Dr Derry considered the various hypotheses on the origin of economic mineral deposits and expressed his belief that the next ten years will show evidence of an increased proportion of ore bodies that owe their origin, at some stage in time, to supergene agencies. He stressed that 'there are no sharp divisions between processes that form and destroy ore bodies at or near surface and those that form or destroy them at a depth of 20 kilometres in the earth's crust. The more we understand about the migration and concentration of metals the more accurately we can apply this knowledge to searching for unknown concentrations, whether at rock surface or at depth. To learn more about these processes of ore genesis we must rely on geochemical studies co-ordinated with field observations'. The five general sessions included accounts of progress in geochemical prospecting in different countries of the world, case histories describing the application of soil, stream sediment, geobotanical and biogeochemical techniques, papers on the behaviour of different elements under varied environmental conditions, discussions on analytical methods and the use of stable isotopes in mineral exploration. It is anticipated that the proceedings of the Symposium will be published late in 1970 or early in 1971 as a Special Volume of The Canadian Institute of Mining and Metallurgy. All registrants at the Symposium will receive a copy of this publication and copies will be available for purchase. At a special meeting called during the Symposium, charter members of the Association of Exploration Geochemists approved a constitution and elected an interim Council which will organize procedure and formulate policy during the coming year. The interim president of the Association is J. Alan Coope, Newmont Mining Corporation of Canada Limited, Toronto, Canada. More information on the constitution and membership in the Association will be distributed to learned societies and technical magazines in the near future. Membership will be open to exploration geochemists in all countries of the world. SOUTH AFRICAN COUNCIL FOR PROFESSIONAL ENGINEERS Report on Registration The Professional Engineers Act (Act 81 of 1968) came into force on the 14th February, 1969. At the time it was recognised that the success of the Act would depend in large measure on the extent to which engineers in South Africa would become registered professional engineers in terms of the provisions of the Act. The promulgation of the Act and its provisions relevant to registration were the subject of considerable publicity during 1969. This has resulted in a rate of application for registration far beyond the capacity of the very active committees set up for this purpose by the South African Council for Professional Engineers (SACPE). To give some idea of the task before these committees and before SACPE itself, which must ratify each case,

By C. H. Wyndham, N. B. Strydom

INTRODUCTION Acclimatization of the labour force to heat is an integral aspect of gold mining in South Africa. A recent survey revealed that about 250,000 Bantu mine workers require to be acclimatized to heat each year. Until 1965 men were acclimatized by means of one of the Chamber of Mines methods (introduced by the Human Sciences Laboratory in 1953). This type of acclimatization was carried out underground where men shovelled rock in hot stopes under careful supervision. However, it has become increasingly difficult in the last few years for mines to provide underground the conditions of work and environmental heat required for adequate acclimatization to heat. In examining an alternative to acclimatization in underground hot stopes, the Human Sciences Laboratory carried out a trial in 1965 of acclimatization in an air-conditioned climatic room on the surface of a mine. The new procedures developed from this trial have been so successful that there are today 26 climatic rooms on different mines. These rooms have been built following a design proposed by Mr Hodgson of the National Mechanical Engineering Research Institute1. Approximately 85 per cent of the total number of men being acclimatized each year are put through the new procedures in these climatic rooms. This paper gives an account of the problems which arose and how they were solved, the inter-relationship between physical conditioning and climatic room acclimatization, the prodecures developed for elimination of labourers with low maximum oxygen intakes, and the advantages of climatic room acclimatization. CLIMATIC ROOMS The majority of the climatic rooms (twenty) have been built on the surface, but a number (six) of mines preferred to establish their acclimatization centres underground in order to decrease the initial costs involved in the construction of such facilities. These underground climatic rooms are usually located near shaft stations in redundant haulages and they can accommodate from 200 to 400 labourers, thus eliminating the need for multiple acclimatization shifts. Figs. 1-4 illustrate various aspects of a surface climatic room. PROBLEMS WHICH AROSE IN INTRODUCING CLIMATIC ROOM ACCLIMATISATION There were four main problems which arose in connection with the introduction of the new method. These were: (i) The type and rate of work to be used. (ii) The air conditions required to obtain optimum acclimatization. (iii) The duration of exposure to heat each day and the total number of days of acclimatization. (iv) The methods of cooling labourers with high body temperatures. Shovelling rock would have been the desirable type of physical work to employ, but the air-conditioned space required to accommodate large numbers of men and the difficulty in standardizing the work rate in shovelling led to the decision to employ instead the work procedure used by the Human Sciences Laboratory in acclimatizing men in the Laboratory. This is the lifting of the body weight against gravity when men step on and off a bench. It has the advantage that large numbers of men can work physically at the required rate in a relatively small space (120 men can be accommodated in an area of 70 ft by 21 ft) and the cost of construction and ventilation of the climatic rooms is thereby reduced. Also the work rate can be standardized by varying the height of the stepping benches in relation to the individuals' body weights. The next problem was the air condition to be used in the climatic rooms. The Laboratory's research experience in acclimatization led it to choose an air temperature of 89°F (with the air almost saturated with water vapour) and an average velocity of air movement of 100 fpm. This air condition was combined with a work rate of 1,560 ft lb/min (oxygen consumption 1.0 litre/min) on day 1, and the work rate was increased gradually over the period of acclimatization to reach a work rate of 3,120 ft lb/min (oxygen consumption 1.6 litres/min) on day 9.