Search Documents

By M. Shaw, H. R. Heydenrych, A. E. Lewis, E. Glass, J. Chivavava

The removal of calcium from the retentates of reverse osmosis (RO) treated minewater is desirable since it allows the recovery of both additional potable water (through RO) and higher-purity salts (in downstream processing). This, in turn, reduces the need for costly and unsustainable evaporation ponds and enhances the economics and operability of potential zero-liquid discharge downstream processes, e.g. evaporative-, cooling- and eutectic freeze-crystallisation. For this study, a multi-component retentate high in sodium content was considered, typical of those emanating from minewater reclamation plants in Mpumalanga, South Africa. Four technologies were evaluated to remove calcium: gypsum precipitation by addition of lime; calcium carbonate precipitation by addition of soda-ash; heating crystallisation of calcium sulphate anhydrite; and cooling crystallisation of gypsum. Full processes were developed and simulated using electrolyte thermodynamics. Using the results of these simulations, capital- and operating costs, as well as revenues were calculated and used in economic comparisons of the processes. Sensitivities to key purchasing and selling prices were also investigated to understand the impact of changes in these variables. For the case of a low magnesium-to-sodium ratio in the feed, gypsum precipitation through lime addition was found to have the lowest operating and total annualised costs; but, if revenue could be derived from the sale of sodium sulphate, calcium carbonate precipitation through soda-ash addition was favoured. Keywords: Calcium removal, gypsum precipitation, calcium carbonate precipitation, heating crystallsation, cooling crystallisation, economic comparison

Jan 1, 2020

It is perhaps somewhat unusual for a contributor to comment on the authors' reply to his critique. However, I should like to return to a specific comment made by the authors. Award to Bob Laburn The Federation of Societies of Professional Engineers (FSPE) is pleased to announce that the 1984 FSPE Award for Services to the Engineering Profession was presented to Dr R. J. (Bob) Laburn at a function held on 14th February, 1984.

Jan 1, 1984

By R. T. Rudd

DISCUSSION R. T. RUDD I have the following comments on Mr Bosman's paper. Before giving the company permission to discharge neutralized mine drainage containing 1800 mg/l of dissolved solids into a public stream, my Department had to consider the matter from both the legal and the practical viewpoint.

Jan 4, 1974

By A. Santana, J. Jankolovits, G. S. Reyes

The flotation of sulfide ores that contain carbonaceous gangue requires significant operational and chemical intervention to achieve suitable metallurgical outcomes. Carbonaceous gangue dilutes concentrate grades, alters the froth behaviour, reduces operational stability, adsorbs reagents, and reduces value recovery. Carbon management processing strategies like preflotation and depression are often presented as point solutions. Moreover, oversimplified mechanisms of carbon depressants belie their complex and nuanced impact on flotation behaviour. Optimising the flotation of carbonaceous sulfide ores requires a holistic consideration of interactions between the carbon management reagents and the processing strategy, ore mineralogy, flotation behaviour, flowsheet, and all other aspects of the flotation system. Examples are shown where conventional, simplistic mechanisms of carbon depressants fail to explain the observed flotation behaviour. The multifaceted impacts of carbon depressants on froth behaviour, collector performance, and value recovery highlight the need for a holistic approach to carbon management. Keywords: Carbon management, carbonaceous ores, sulfide flotation, carbon depressant

Jan 1, 2020

By C. Mueller

In many automated mines, multi media video and audio funtionality has to be combined with sensor information or steering commands, which is the idea of a new, PC based integrated and multi media capable control system. The new control system (Multimedia Control - MMC) bases entirely on TCP/IP networking and internet technology. For the first time, this enables the ‘intelligent’ use of video and audio information: pictures and voice sequences may be forwarded on request only, they may be stored if particular events occur (e.g. video black boxes) and sensor signals as well as actions from the automation system can directly be assigned with multi media sequences. MultiMedia Control entirely bases on object oriented software. It uses most modern software technology. As user interface, only a standard web browser is required. This makes the handling of different machines easy. By using mobile web pads, dedicated local operator interfaces are not required any longer. The service staff just connects to the automated equipment by – wireless –LAN to make required adjustments. Customization is easy using an open Application Programming Interface. Software modules may be added to the system without touching or recompiling existing components. The system was prototyped in 2000 using a demo-application. The performance tests showed very positive results both regarding the control system behaviour and the speed/latency timing behaviour of the multi-media information processed. The system now is slightly reshaped to completely meet the final product requirements. It is expected to be available by the end of 2001. Key words: Machine Automation; Control System; Multi Media; Remote Control; Teleoperation; Ethernet; TCP/IP; Internet Technology; Streaming Video; Quality Assurance; Service; Control Centre.

Sep 1, 2001

By C. A. Jermy, B. J. Venter

Excessive build-up of methane and water pressures was identified as the leading cause of some Q/the roof falls in a coal mine in the eastern Transvaal. In order to characterize the migration of the methane and water into and around the mined coal seam, a laboratory investigation of the permeability of the roof strata was undertaken. The aim of the investigation was to correlate changes in the fades with changes in permeability to enable the prediction of possible zones of pressure buildup. The tests were carried out on samples from borehole core that had been obtained from the roof strata as part of the mine exploration programme. Permeability measurements were then conducted under atmospheric and triaxial-stress conditions. For the tests under atmospheric conditions, a modified Ohle cell was used and, for the tests under triaxial-stress conditions, a modified Hoek cell was used. The liquid equivalent permeability?s of the different samples were obtained by use of ASTM D4525- 85, and these were then used as a basis for comparison. Facies type, i.e. grain size, was found to have an influence on the permeability but, owing to the variable nature of the sediments, a range of permeability rather than a specific permeability value was associated with each type of Jades. The measured permeability was bound to decrease with an increase in gas pressure. The liquid equivalent permeability was bound to increase with an increase in grain size for the coarser-grained Jades, and to decrease with an increase in grain size for the finer-grained types. The application of an external stress regime to the sample was bound to reduce the permeability, but the amount of the reduction depended on the type of stress. The permeability was also found to depend on the recent stress history of the sample. The authors conclude that the methods described are useful for the correlation of facies type with permeability, but that the results are sensitive to changes in locality.

Jan 1, 1994

The nature of metallurgical engineering?applying and optimising chemical and physical processing of ores into useful materials?is reviewed. Important trends that shape the context in which metallurgical engineers practise are identified ? increased global production of primary metals, declining prices, environmental constraints, and increased property requirements of materials. A successful department of metallurgical engineering is one which employs a team of academic leaders to develop graduate engineers who are productive across the full range of metallurgical processing. Keywords: metallurgical engineering, primary metals, commodity prices, processing

Jan 1, 2003

By D. Mesa, J. Karvonenb, A. López, P. R. Brito-Parada, R. Grau, D. Davoise

The froth zone in flotation cells plays an important role in determining metallurgical performance. This is even more critical as cell sizes increase, since larger bursting surface areas can easily result in poor froth transport and even stagnant froth zones, which are detrimental to recovery. Generating additional overflowing lip length by adding internal launders and reducing surface area (while also directing the froth to the overflow) by adding crowders are well established design strategies to enhance froth mobility. However, comparative experimental studies of froth zone design modifications at industrial scale are scarce and often lack detailed froth characterisation. In this work, we present the results of two experimental campaigns that were carried out at Atalaya’s Riotinto concentrator in order to determine the effect of a new froth zone design on the flotation performance of a TankCell® e300 cell that operates as the first cell of the rougher bank. These campaigns provided a unique opportunity to assess froth phase phenomena and metallurgical performance before and after changes in design. The original cell design had an internal peripherical launder and a froth cone, while the new concentrate launder technology adds a centre launder and an adjustable froth crowder to the existing launder design. The new concentrate launder arrangement reduces significantly the froth area as well as the froth transport requirements, aiming to improve froth recovery and, consequently, enhance flotation performance, allowing copper recoveries in the TankCell® e300 cell to increase dramatically. In addition, radial profiles of froth height and froth velocity at the surface were determined, which provide valuable insight into the effect of design changes on froth stability and mobility. Keywords: Flotation performance, enhanced recovery, launder, crowder, froth stability

Jan 1, 2020

By K. G. Lomberg

The density used to covert volume to tons is critical in determining the real in-situ tonnage of Mineral Resources. However, the methods used to determine density and the use of different technical terms are seen to be inconsistent throughout the industry. Probably the best discussion addressing the determination of density was presented by Lipton (2001). This paper does not try to replicate this excellent work, but rather to review current industry practice and present a comparison of the approach to density in public reporting. Some of the technical terms used in reporting and the common methods applied are also discussed.

Sep 1, 2021

By T. Moodleya, I. Govender

Despite the widespread use of DEM to simulate particle processes, comparatively little work has been done to evaluate its accuracy. One of the reasons is a lack of available measurement techniques that can capture dynamic information at the momentum transfer timescale which is lower than 10-6 s - typical of the kinetics occurring within the drum. This work makes use of Positron Emission Particle Tracking (PEPT), an in-situ method capable of measuring 3D kinematic data at 1000 frames per second. PEPT measurements are performed using 3 mm and 5 mm mono-size glass beads in a 300 mm diameter rotating drum at critical speeds that are relevant to industry. We undertake systematic ‘tuning’ of DEM with a view to optimising the agreement between experiment and simulation. To ensure an equitable comparison scale, both the DEM and PEPT data are coarse grained within representative volume elements. This work seeks to validate DEM predictions against experimentally derived PEPT kinematic measurements. Keywords: PEPT, nuclear imaging, DEM, Tumbling Mills

Jan 1, 2020

By K. J. Kruger

Aluminium alloys have gained popularity in many industries due to their high strength and low weight. One shortcoming of aluminium alloys is their poor resistance to abrasion and erosion wear compared to materials such as stainless steels. In this project, aluminium alloy 2014 (AA2014) was coated with a 1.5 mm thick laser-deposited layer composed of silicon, copper, and aluminium with the aim of increasing the wear resistance. The amount of silicon, copper, and aluminium added to each sample was determined by a mixtures model. It was discovered that the Al-Cu system is very sensitive to silicon additions and that wear resistance depends on the primary phase to solidify as well as on the final phase distribution. Two primary phases were identified; alpha aluminium and theta intermetallic. It was observed that the clad layer increases both the hardness and wear resistance of AA2014, and that the material solidifying as primary alpha aluminium displayed a lower hardness but higher wear resistance than the samples containing primary theta phase. All clad layers performed better in terms of wear resistance than the unclad samples. The knowledge gained and principles used in this project could be applied to many other aluminium alloys.

Jan 1, 2014

In the previous chapters we did not concern ourselves with the fact that the geostatistical properties of the regionalized variable x (z) are affected by the size of the support w. Ideally, when analysing an ore body O, we would like to determine the properties of point values in O, i.e. the properties of a regionalized variable with an infinitely small support, say w°. In practice, point values are never known. To measure the value of x at a point z we must take a sample of size w centred at z. For example, if we are interested in the grade at point z, w will be the volume of the sample 'centred in z; if we are interested in the metal accumulation at point z, w will be the area of the cross-section of the sample centred in z. We say that the measured property is a regularized variable, and so the semivariogram (or covariogram) calculated from the values obtained is also regularized. In the majority of the mining problems which can be solved by geostatistical methods, we are interested in the properties of blocks of ore and of samples with a finite non-point support. It will be shown in the following chapters that these problems can be solved by calculating the average value of the point sernivariogram in volumes or areas of finite dimension, or between such volumes or areas. These calculations would be simple if we knew the point semivariogram. This means that the point semivariogram has to be estimated from the observed regularized semivariogram(s).

Jan 1, 1978

By B. Genc, C. Gous

Spontaneous combustion during coal mining operations is a major problem that affects the health and safety of workers and causes environmental problems. The phenomenon is associated with the presence of coal, coal shale, and pyrite. In 2020, a premature detonation incident occurred at an iron ore mine where the waste material contains black carbonaceous shale units known to be associated with pyrite. The spontaneous combustion propensity and properties of samples of the black carbonaceous shales from the mine were examined and compared with samples from the Witbank Coalfield. The spontaneous combustion liability indexes of these samples were correlated with X-ray fluorescence (XRF) and proximate and ultimate analyses using linear regression. The Wits-Ehac Index classification results show that the samples were between medium and high risk. The linear regression analysis showed very poor correlations between the Wits-Ehac Index results and the XRF and proximate and ultimate results. The most valuable relationship found is between the presence of relatively high sulphur (greater than 3%) and ground reactivity with nitrate-bearing explosive emulsion.

Jun 5, 2023

By P. Minkkinen, R. C. A. Minnitt

Particle size distribution analysis is important to many industries for assessing product quality, process efficiency, and compliance with contractual standards, while ensuring sample accuracy, and representativeness. Inaccurate particle size distribution results, arising from fines due to excessive handling can lead to penalties and buyer-seller disputes. A non-representative particle size distribution means samples will not accurately represent the chemical components either. Sampling blasthole cuttings poses challenges due to large material volumes, segregation, and uneven settling of particles in dense gold bearing ores. Commonly used sampling methods, such as spear or sectoral sampling, may lack representativeness. Particle size distribution analysis is crucial for evaluating sampling methods by comparing test sample representativeness against a reference standard derived from multiple particle size distribution analyses. Acceptable samples must fall within the 97.5% confidence intervals of the standard; deviations analyses lying outside these boundaries indicate a strong likelihood of segregation errors. A case study demonstrates this approach by using a 6.005 kg benchmark sample to assess two additional samples (1 kg and 5 kg), highlighting particle size distribution’s role in detecting sampling errors and refining protocols. An example of three test samples collected from reverse circulation drill cuttings compared to a standard reference sample is presented to illustrate a quality assurance/quality control procedure for reverse circulation drilling.

Oct 2, 2025

By A. S. Geldenhuys, L. S. Leal Filho, D. A. Deglon, T. C. Souza Pinto

The Brucutu iron ore mine (Minas Gerais, Brazil), is Vale`s largest iron producing operation achieving around 21 million tons by flotation of iron ore pellet feed per annum. The run of mine is mainly composed of hematite (70%) and quartz (30%). After preparation (comminution and sizing), the slurry is submitted to reverse cationic flotation of quartz under basic conditions (pH=10.5). Corn starch (500g/t) is used to depress Fe-bearing minerals and alkyl (C10) ether amine is the collector for quartz. The flotation circuit is arranged in a “coarse” section utilizing dated 28m3 square Wemco cells, and a “fine” section utilizing modern 160m3 tank cells. The “coarse” flotation circuit treats material from the deslime cyclone underflow while the “fine” circuit treats material from the deslime cyclone overflow and the pulp product from the “coarse” circuit scavenger 2 bank. Evaluation of process performance is of high importance as even small gains can lead to large improvements for this high throughput plant. Cell-by-cell samples of the froth products, selected feed and pulp-products were analyzed for flow-rate, overall chemical composition, and particle size distribution. Bank-by-bank samples of the feed, froth and pulp products were analyzed on an assay-by-size basis. In addition, the flotation cells were hydrodynamically characterized and gas dispersion parameters assessed. The detailed experimental program resulted in a thorough characterization of the process and enough information to produce a calibrated floatability component model. Longer mainline residence time results in significant Fe2O3 losses while yielding little benefit in terms of SiO2 grade. Scavenger 2 has twice the residence time of scavenger 1 while having to treat only 10% of the SiO2; resulting in high Fe2O3 recoveries to the froth and poor separation. In addition, it is shown that the Fe2O3 exhibits true flotation behavior resulting in increased Fe2O3 losses. The detailed data collection campaign coupled with in depth data analysis and modelling gives unprecedented information and highlights avenues for optimization that was previously unknown. Keywords: Froth Flotation, Process modelling, Process evaluation, Metallurgical survey

Jan 1, 2020

By J. D. Koch

The past ten years or so have seen many changes in the methods and approach adopted for projects in the metallurgical and mining industry in South Africa. These changes have led to an increased use by operating companies of the project and construction management services offered by engineering contracting companies. For a variety of reasons, this development has been slower in the metallurgical industry than in other areas of production, but that industry is also now showing an increasing trend in this direction.

Jan 1, 1981

The October General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 21st October, 1970, at 4.30 p.m. V. C. Robinson (President) was in the chair. There were also present 25 Fellows, including J. K. E. Douglas, Prof D. D. Howat, D. G. Maxwell, Dr R. E. Robinson, P. A. von Wielligh (Council Members). D. Ayres, G. Burrow, E. H. D. Carman, D. L. Carson, M. E. E. Douglas, S. A. Finney, W. R. Flook, A. J. Freemantle, W. A. Gilbert, E. B. Gordon, B. W. Gray, J. M. Jacobs, P. H. Kitto, C. H. Kruger, Dr P. J. D. Lloyd, D. G. Malan, W. Pilkington, W. G. Pyne-Mercier, K. S. Rae, W. T. Ruhmer, D. J. Tutt and D. T. Watt. Seven Members, including E. J. Dominy, S. I. du Preez, L. V. Grobler, D. R. Lings, G. D. Louw, J. S. A. Oelofse and O. B. Prentis. Fifteen Visitors, including J. R. Coppin, Dr A. Faure, P. E. Franzl, G. P. Hart, D. van Heerden, A. W. Hunt, A. R. F. MacDonald, B. G. Meyburgh, P. H. Radcliffe, J. M. Shirley, T. H. Tunley, A. D. Vellema and R. E. Wheeler. Secretary, D. C. Visser. Total present: 49. OBITUARIES The President: "It is my sad duty to announce the death of the following: Sir George Arthur Davenport, Honorary Life Fellow, who joined the Institute in 1930 and passed away on 17th September, 1970. The late Sir George was also, for many years, our corresponding member for Rhodesia. Andrew Malcolm Carmichael, Associate, who joined the Institute in 1944 and passed away on 22nd August, 1970. Cyril John Douglas Veal, Life Fellow, who joined the Institute in 1929 and passed away on 27th August, 1970. As a mark of respect to the memory of the deceased and in sympathy with the bereaved I would ask you all to rise and observe a few moments' silence." CONFIRMATION OF MINUTES The President: "May we confirm the minutes of the Annual General Meeting held on 26th August, 1970, and the minutes of the monthly general meetings which were held on the 20th of May and the 17th of June, 1970, as published in the August Journal." Agreed. MEMBERSHIP The President: "I have much pleasure in announcing that the names of the undermentioned candidates, having been published in accordance with By-Law 5.2.2., Council has elected them to membership of the Institute in the following grades: Members: Nikolaos Lalakakis, Gordon Phillips Rundle. Associates: Henry du Preez, James Robert Forbes, Johannes Stephanus Albertus Oelofse, Casper Vorster van Heerden. Graduates: Michael Harold Crosbie, Graham Robert Wallis Walker, Gary Walker Braithwaite. Students: Mohammad Ali Kazemzadeh, Gerhardus Petrus Benade. APPLICATIONS FOR TRANSFER From Graduate to Member: James Wormald. From Student to Graduate: Peter John Cook, Pieter Willem Greeff. "I welcome the newly elected members to the Institute and congratulate the members who have been transferred to a higher grade." PAPER FOR PRESENTATION The President: "This paper is entitled 'The Design, Erection and Operation of a Purlex Plant at Buffelsfontein Gold Mining Company Limited'. It is presented to the Institute by Mr B. G. Meyburgh, a visitor to our Institute. He is a graduate of the University of the Orange Free State and is the Uranium Plant Superintendent at Buffelsfontein and he, therefore, is in a very strong position to describe this very excellent job which is being done as he has been associated with this plant from the inception." After the presentation of the paper the President said: "Gentlemen, the paper you've heard from Mr Meyburgh is a very concise and interesting account of an important piece of work, and I think the title is so completely descriptive of the subject, which is admirably set out in the paper which you have heard. You probably haven't all had the opportunity of reading it, but you very soon will. I found it interesting to note that the results predicted were surpassed in the operation of the plant to date. The actual results obtained are significantly good, I think. Any process which, in this country, increases production and decreases costs, is to be welcomed, particularly when it is so necessary for South Africa almost to bend over backwards to utilise every avenue available in order to increase the scope of the production for overseas' markets, of her metallurgical and mineral potential. In lighter vein-and there is no reason why we should always be so serious-I am glad to see that, in a scientific journal like this, such words as the American word 'crud' which I have been picked out about so often, because my grandchildren use it, is now given an aura of respectability. Thank you very much, Mr Meyburgh, for an interesting paper. We have a long list of contributors, and I am not going to waste any more time. I am going to call on Mr Tunley of the N.I.M. for the first contribution." T. H. Tunley, P. de Bruyn (read by A. D. Vellema), E. J. Dominy, E. H. D. Carman, A. R. F. MacDonald D. C. Streicher (read by P. H. Radcliff), Dr A. Faure and Dr P. J. D. Lloyd then contributed to the discussion. (This discussion will appear in a later issue of the Journal.) The President: "I wish to thank members and visitors for their attendance, and now declare the meeting closed." The meeting closed at 6.05 p.m.

By A. Koning

Pressure hydrometallurgy operations require vessels to be lined with an impermeable membrane for corrosion protection and one or more courses of refractory or ceramic brick. Examples of unit operations that utilize composite lining systems include pressure oxidation autoclaves, sulphide precipitation autoclaves, chloride leach reactors, flash vessels, cyclone separators, and direct contact condensers (heater vessels and quench vessels). The refractory lining must satisfy multiple requirements: it must thermally insulate the membrane from process fluid, be structurally stable, provide erosion resistance, be chemically compatible with process fluid, and provide an economic service life. New hydrometallurgical processes are pushing the pressure, and temperature with each new generation of plants. A fundamental understanding of all factors affecting the mechanical stability of the lining system is essential as lining designs move further away from the industry?s experience base. The method of designing a refractory lined vessel is examined taking into account the impact of irreversible chemical swell, operating factors, design factors, and installation factors. The effect of geometry and incorporating additional degrees of freedom to the analysis is explored using two-dimensional and three-dimensional finite element analysis (FEA). The effect of these additional degrees of freedom on the results of the one-dimensional model are discussed. Keywords refractory lining design,autoclave, finite element analysis.

Aug 1, 2013

By S. Shi, X. Xia, F. Xuesai, Z. Shen, D. Han

The hydrodynamic characteristics of a mechanical flotation cell’s transportation zone have significant impact on its metallurgical performance, especially on coarse particles recovery efficiency. However, how to define and adjust the transportation zone was seldom investigated by researchers. In this paper a method will be introduced to define the boundary of the transportation zone by PIV measurement. It is found that the transportation zone can be extended upwards by enlarging the entire rotor-stator assembly from the bottom of tank and increasing the jet angle of the impeller. Two control methods have been validated in industry tests on KYF-160m3 and KYF-320m3 air-forced mechanical flotation cells. The result shows coarse particles recovery are both improved distinctly. It is suggested that enlarging the top transport boundary is able to helpful to reduce the floating distance of bubbleparticle aggregates, which contribute to improve coarse particle recovery in large flotation cells. Key Words: Flotation cell; Transportation zone; Coarse particles flotation

Jan 1, 2020

The FSPE Award for Services to the Engineering Profession was awarded to Or Francis George Hill at a ceremony held in January of this year by the Federation of Societies of Professional Engineers. The following is an abridged version of the citation made by Professor A.N. Brown, President of FSPE, and of Or Hill?s reply. Achievements. It is indeed fitting that such a distinguished group of people have gathered on this special occasion to honour and pay tribute to Or Pinkey Hill

Jan 1, 1988