Search Documents

By J. Sehata, J. Tshilongo, I. Govender, S. Pikinini, T. L. Moodley, M. Raedani

In the face of dwindling Merensky ore reserves in the early 1990s, Mintek developed the MF2 flotation circuit to economically recover platinum group metals from the shallow upper group-2 chromitite reef. By aligning the primary and secondary grind to the platinum group metal liberation kinetics, excessive fine chromite generation was avoided, and thus one could consistently produce high-grade concentrates (>200 g/t platinum group metals) with low chrome content (<3% Cr2O₃), well within smelter tolerances. This, coupled with upper group- 2's low-cost open-pit mining, made it particularly attractive to investors and mining houses alike. As a result, deeper lying reefs like middle group and lower group with lower platinum group metals grades and complex mineralogy, were primarily mined only for chromite using density-based separation processes (like spirals), of which the waste tailings are best classified as secondary platinum group metals resources. Today, with global platinum group metal demand rising and high grade upper ground-2 reserves rapidly diminishing, the industry must revisit these middle group and lower group tailings. Mineralogical analysis reveals several challenges: Middle group tailings feature platinum group metals locked within silicate matrices, while lower group tailings contain fine chromitite fragments, and are hosted within non-floating laurite grains, each presenting liberation and gangue issues. Smelter constraints still demand concentrates below 3% Cr₂O₃, requiring solutions that consider both platinum group metals recovery and chrome entrainment. To develop a solution, two lower group chrome spiral tailings samples were obtained from a large chrome mine: Sample A (+425 μm – 106 μm) and Sample B (−106 μm). Initial assays showed Sample B contained higher platinum group metal grades but also higher Cr₂O₃. As such, different blends of flotation feeds were evaluated using ratios of 90:10 (C1) and 80:20 (C2) of Sample A to Sample B, targeting the coarse fraction's lower chrome content while recovering valuable platinum group metals from the fines. This work proposes a practical route for mining houses to unlock additional platinum group metal value from lower group ore spiral tailings. By optimising blending ratios and reagent suites, it is possible to meet smelter chrome and platinum group metal grade thresholds, whilst still obtaining economically viable PGM recoveries.

Mar 6, 2026

By T. Vincent, J. Steele, C. Debrunner, M. Whitehorn

This paper presents current work on the development and use of stereovision for underground mining. Information on the calibration of the cameras and the feature-matching algorithm are presented. This system uses an intensity-based approach that evaluated correspondences along the epipolar line. Once features have been identified and their distance from the cameras computed, a three-dimensional map of the muck pile is developed. The approach used here uses a ray-tracing algorithm. This approach provides an uncertainty measure along with the elevation. A discussion of the use of this modelling information in the control of the LHD is included. Keywords: Robotics, automation, LHD, underground mining, vision sensing, task automation, tele-operation

Sep 1, 2001

By F. M. L. Mulaudzi

Metal dusting is a corrosion phenomenon that occurs in strongly carburizing gas atmospheres at elevated temperatures. Reaction kinetics and product characterizations of Alloys 602CA and 800 were examined by scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX) and X-ray diffraction (XRD).The results showed that Alloy 602CA is more resistant to metal dusting than Alloy 800. Visual examination and SEM surface analysis showed that Alloy 800 suffered metal dusting attack after a relatively short exposure period. The amount of coke deposits increased on Alloy 800 with increased exposure from 96 to 336 hours. X-ray diffraction on the reacted surfaces identified graphite and austenite in both alloys and some iron oxides/spinel for Alloy 800.

Jan 1, 2012

By H. S. Baloyi, J. J. Rust

Spiral concentrators are widely applied to beneficiate commodities such as Cr2O3, mineral sands, and ferrochrome. The application of spirals for heavy minerals has been limited to a feed top size of 1 mm. At particle sizes larger than this, friction retards heavy particles and the particles' primary velocity approaches zero, resulting in a solids build-up, therefore inhibiting further separation. Recently, a new Multotec SC25 spiral model was introduced to the industry, which aids in beneficiating particles of up to 3 mm, with successes having been demonstrated in ferrochrome slag and titanium-bearing minerals. This spiral also has potential in electronic waste applications. This paper examines the applicability of the SC25 spiral in coarse Cr2O3 recovery. This stems from the fact that junior chrome miners tend to discard particles larger than 1 mm as they neither have milling nor dense media circuits. Also, alluvial chrome miners discard +1 mm even though this size fraction contains recoverable and liberated Cr2O3. The SC25 spiral has shown better Cr2O3 separation efficiencies than the SC21 model and with higher SiO2 rejection at saleable grades, thus providing an additional revenue stream specifically for the coarser (+820 μm) size fractions. Keywords: Spiral concentrators, chromite recovery, specific gravity, SC25 spiral, coarse spiral

Jan 1, 2020

By A. Singh, K. Bisaka, G. Marape, T. Mokgomola

This paper investigated the pre-concentration amenability of sovite (carbonatite) ore to enhance the grade of rare earth elements (REE) bearing minerals by rejecting calcite, and to improve total rare earth elements (TREE) recovery using gravity and magnetic separation. A high proportion of calcite affects downstream processes like leaching due to high acid consumption. Multiple flowsheets combining gravity and magnetic separation were employed to target > 60% TREEs recovery to the final concentrate and > 60% calcite rejection to the tailings. Head analysis of the feed showed the sample’s main constituents as Fe (15.61%), Ca (16.04%), SiO2 (7.13%), and lastly TREEs (1.12%). Mineralogy liberation data at 2mm top size indicated poor liberation of TREEs, with the majority of minerals displaying < 30% mass greater than 80% liberated. Grain size distribution data showed that the majority of REE minerals are fine grained and report to the < 20 μm size class. Calcite liberation mineralogy showed < 60% mass greater than 80% liberation.A combination of a single-stage shaking table with a wet high intensity magnetic separator at a magnetic intensity of 7520 G was found to be the optimum flowsheet. For a shaking table feed with P80 of 150 μm followed by tails regrind to P80 of 45 μm as feed to wet high intensity magnetic separator, the overall mass balance results showed that 60.5% TREEs are recovered to the concentrate while 63.0% calcite is rejected to the tails. However, due to the fine-grained nature of This paper investigated the pre-concentration amenability of sovite (carbonatite) ore to enhance the grade of rare earth elements (REE) bearing minerals by rejecting calcite, and to improve total rare earth elements (TREE) recovery using gravity and magnetic separation. A high proportion of calcite affects downstream processes like leaching due to high acid consumption. Multiple flowsheets combining gravity and magnetic separation were employed to target > 60% TREEs recovery to the final concentrate and > 60% calcite rejection to the tailings. Head analysis of the feed showed the sample’s main constituents as Fe (15.61%), Ca (16.04%), SiO2 (7.13%), and lastly TREEs (1.12%). Mineralogy liberation data at 2mm top size indicated poor liberation of TREEs, with the majority of minerals displaying < 30% mass greater than 80% liberated. Grain size distribution data showed that the majority of REE minerals are fine grained and report to the < 20 μm size class. Calcite liberation mineralogy showed < 60% mass greater than 80% liberation.A combination of a single-stage shaking table with a wet high intensity magnetic separator at a magnetic intensity of 7520 G was found to be the optimum flowsheet. For a shaking table feed with P80 of 150 μm followed by tails regrind to P80 of 45 μm as feed to wet high intensity magnetic separator, the overall mass balance results showed that 60.5% TREEs are recovered to the concentrate while 63.0% calcite is rejected to the tails. However, due to the fine-grained nature of TREEs, no flowsheet improved their grade.

Nov 6, 2024

By M. -A. de Ville d’Avray, J. Bosman, S. Brochot

Dense Medium Separation (DMS) technologies are used for light (coal, lithium) or heavy (chromite, iron ore, diamonds) minerals concentration, but also for ore pre-concentration (Pb/Zn) or waste (plastics). Dense media are mainly formed from a suspension of magnetite or ferrosilicon in water. Such DMS circuit design or optimisation requires a full and detailed material balance which can be obtained by the aid of modelling and simulation tools. This balance is not limited to ore and its valuable minerals, but also the recovery of the dense medium itself. If the density is the main property used for separation, the particle size plays a non-negligible role, and, more precisely, the liberation classes which can be associated to the washability curve. The paper presents how the modelling and simulation platform USIM PAC can answer this challenge with the set of models for DMS operating units such as drums or cyclones, and their associated screens (drainage, rinsing) and magnetic separators for medium recovery. Some examples for mineral concentration will illustrate this approach. Keywords: Process simulation, process modelling, dense medium separation, process optimisation

Jan 1, 2020

By A. McQuillan, N. Bar

Geotechnical engineers are routinely tasked with advising suitable stand-off distances below highrisk sections of slopes in open-pit mines that are identified to have potential to deform or collapse. Accurate prediction of failed material runout can mean the difference between continuous safe mining and unwanted high-potential incidents that result in loss of production, equipment damage, injury, or loss of life. This paper updates previous empirical relationships presented by the authors for estimating the volume and runout distance of excavated slope failures, in an open-pit mine operation, using slope geometry as the primary predictor. Cases are sourced from varying slope geometries (fall heights up to 385 m, slope angles up to 80°) and a range of commodities (iron ore, coal, nickel, gold, copper, boron, and limestone), excavated in sedimentary, banded-sedimentary, epithermal, and copper-porphyry deposits, across all six inhabited continents. Analysis of these cases identified positive correlations between slope height and runout distance, and slope height and failed material volume. In general, negative correlations were identified between Fahrböschung angle and slope height, and Fahrböschung angle and failed material volume; however, significant scatter is observed in these datasets. A definitive relationship could not be derived comparing Fahrböschung angle with failed material runout. Slope angle was also found to be a poor indicator of runout. Of the parameters analysed, slope height (i.e., fall height) was found to be the simplest and best predictor of runout distance. This paper presents new charts for predicting failed material runout distance for rock slopes. Relationships are defined for structurally and rock-mass driven slope failure mechanisms at average, 75%, and 95% prediction intervals

Jul 10, 2024

"Chairman: Professor J. de V. Lambrechts Rapporteur: Mr R. HempPapers:Computer-aided design of a flash smelting installation by M. A. T. Cocquerel, R. T. Gates and L. A. GreenPlanning of mine ventilation by E. U. Reuther and A. DohrnenCoal mine ventilation systems in the U.S.A. by R. Stefanko and R. V. Ramani Heat flow models in ventilation planning by A. J. Dickson and A. M. StarfieldThe first of the papers in the session dealt with a flash smelter installation, while the remaining three papers dealt with mine ventilation. In view of this the Chairman proposed that the paper on flash smelting be introduced and discussed first, after which the remaining three papers would be introduced followed by discussion on all three.Dr Cocquerel, who presented the first paper, used some typical flow diagrams to illustrate the process and stated that the program considered only steady-state operations and did not take into account the dynamical changes. Subjective judgment was necessary for the preparation of input data and some degree of user appreciation was required.Dr Cocquerel said that no work bad yet been done on an optimization program, but that this was being considered. Such a program would require a large amount of physical and chemical data which were not yet available. The variables to be optimized were the energy and material consumptions and the loss of metal in the slag.The Chairman opened the discussion by asking Dr Cocquerel if he could give a brief description of the flash smelting process for the benefit of those not familiar with the subject. Dr Coquerel replied that in the Outokumpu process con¬centrates were injected directly into the furnace, and that the process was somewhat analogous to flash distillation or evaporation processes, but was perhaps closer to the burning of pulverized fuel.The process had two distinct advantages. First, the heat evolved in the smelting reaction was used to heat the furnace, which resulted in less fuel consumption, and, second, the effluent gases were cheaper to treat than the effluent gases from other pyrometallurgical processes. This was important particularly in view of the current interest in pollution problems.Mr P. Marais thought that the authors had done themselves an injustice by not including details of the very complex processes taking place in the furnace."

Jan 1, 2014

By P. Mühlen, C. Nelson

Process control optimisation depends a lot on the availability of timely data from production to give operators a chance to make adjustments before potential process upsets or disruptions happen. A lot of data is already available with newer and updated machine technologies, but what about the process upsets coming from the raw materials that we use? They are natural products and therefore they are not of a stable composition or mineralogy. The production process depends on a certain chemical or mineralogical stability of the raw materials when they come to a roaster, kiln or sintering stage. Only then can the proposed reactions take place and the equipment be operated at stable temperatures. Laboratory analytical technologies have the limitation that they depend on representative samples and have a long time delay. Therefore online (real time) analysers are used nowadays in mining applications to obtain an early indication of the actual mined or to-be-processed ore. Most available technologies can only analyse inorganic content on an oxide or elemental level. Near infrared (NIR)- based online analysers can overcome that limitation and give a real time analysis of organic as well as inorganic composition, if required on a mineral level. The paper will present two case studies where the NIR online technology was successfully adapted.: a) Optimising refractory gold ore processing at the Goldstrike roaster operation b) Optimising the sinter process at a Japanese manufacturer. Keywords: Analyser, NIR, online, realtime, gold, roaster, iron ore, sinter, mineral phase analysis

Jan 1, 2020

By C. O’Donova, E. Adam, L. A. Torres-Cruz

High-profile failures of tailings dams illustrate the significant safety challenge they pose. The decant pond of such facilities plays an important role in their mechanical stability. This study investigates the feasibility of using public multispectral data collected by the Sentinel-2 satellite mission to monitor the area of the decant pond. The Sentinel-2 mission has a revisit time of 5 days and the data used herein has a spatial resolution of 10 m/pixel. We considered two water-detection metrics: the normalized difference water index (NDWI) and the near-infrared (NIR) reflectance. Implementation of the method at a South African platinum tailings dam illustrates the capabilities and limitations. Public, sub-metre resolution true-colour imagery served as validation data. There is good agreement between pond area measurements based on Sentinel-2 and the validation imagery. These results suggest the feasibility of using Sentinel-2 data to supplement the monitoring of the decant pond.

Apr 2, 2022

By R. Koen, H. Visser, A. Roodt

"SynopsisThe tetraethylammonium salt of the mono-anionic coordination compound mer-oxidotrichlorido(thenoyltrifluoroacetylacetonato- K2O,O’)niobate(V) (NEt4)[NbOCl3](ttfa)], has been prepared under aerobic conditions and characterized by single-crystal X-ray diffraction. (NEt4)[NbOCl3](ttfa)] crystallized in the monoclinic P21/c space group, with a = 11.483 (5), b = 12.563 (5), c = 17.110(5) Å, and ß = 100.838 (5)o. The complex structure exists in a 50.0% (NbA) : 50.0% (NbB) positional disorder ratio.IntroductionComplexes containing organometallic type ß- diketone ligands with O,O and O,N donor atoms are used widely in coordination chemistry and have applications in catalysis, radiopharmaceuticals, etc. (Schutte et al., 2011; Roodt, Visser and Brink, 2011; Brink et al., 2010; Otto et al., 1998). These ligand systems are very useful because of their highly coordinative nature, high solubility, and also due to their ability to be functionalized with various substituents on the carbonyl carbon atoms (Schutte et al., 2011).Only a small number of ß-diketonate ligands have successfully been coordinated to a Nb(V) metal centre, with only a select few being characterized by X-ray crystallography (Viljoen, 2009; Bullen, Mason and Pauling, 1965; Preuss, Lamding and Mueller-Becker, 1994; Funk, 1934; Davies, Leedlam and Jones, 1999; Allen, 2002. The synthesis and crystal structure determination at room temperature of mer-oxidotrichlorido (thenoyltrifluoroacetylacetonato- k2O,O’)niobate(V) {(NEt4)[NbOCl3(ttfa)]} was first reported by Daran et al. in 1979. Accordingly, for this current investigation, (NEt4)[NbOCl3(ttfa)] was re-evaluated at 100 K to determine if the structural features might change with temperature."

Jan 1, 2015

By C. Karageorgos, J. Sakala, A. Prinsloo, B. Ngambi

The sulphide flotation circuit at First Quantum Minerals’ Kansanshi mine in Zambia produced over 100,000 t of copper in 2019. For this circuit, mineralogical analysis has shown that the majority of the copper lost is hosted in fine liberated chalcopyrite, which is a paramagnetic mineral. The objective of this work was therefore to improve fine chalcopyrite recovery in the sulphide flotation circuit at Kansanshi, using a magnetic conditioning technology to agglomerate fine paramagnetic minerals. This theoretically increases the probability of attachment during collision and therefore improves recovery. A four-month paired ‘t’ test plant trial was carried out and comprised of consecutive ON-OFF periods with and without magnetic conditioning in the rougher flotation bank of the sulphide circuit. The experimental design involved assessment of recovery by size based on daily and weekly composite samples of feed and tails, sized using both wet-screening and cyclosizer. Both the daily plant data and the sized samples showed an increase in Cu recovery with magnetic conditioning ON. A 0.56% copper recovery improvement was measured with magnetic conditioning at a 99.4% confidence level. Keywords: Flotation, fine mineral, chalcopyrite, magnetic aggregation

Jan 1, 2020

By D. A. Hayman, N. Rambuda, N. A. Sithole, C. Hockaday, J. D. Steenkamp

"Mogale Alloys operates two alternating current (AC) submerged arc furnaces (SAFs), and two direct current (DC) open bath furnaces. These furnaces are capable of producing two products, silicomanganese (SiMn) and ferrochrome (FeCr), with a total production capacity of 110 000 t/a. This paper focuses on the silicomanganese process specific to Mogale Alloys, with a two-furnace operation facility that produces 55 000 t of SiMn per annum.IntroductionMogale Alloys is situated in Krugersdorp in the West Rand District Municipality in South Africa’s Gauteng Province. The Krugersdorp facilities were initiated by Palmiet Chrome Corporation in February 1963 to produce charge chrome (Basson, Curr, and Gericke, 2007). Mogale Alloys bought the Palmiet Chrome facilities in 2005 from Samancor Chrome. The Afarak Group currently owns 90% of Mogale Alloys.SiMn is produced in two 20 MVA submerged arc furnaces (SAFs), which were originally built for chromite processing, and ferrochromium (FeCr) in two DC open bath furnaces rated at 40 MVA and 10 MVA. When this paper was compiled, the 10 MVA furnace was not operational due to the high cost of production, and one of the 20 MVA SAFs was recently converted to produce FeCr due to market constraints. Mogale Alloys has 290 permanent employees with four contracting companies on site. The paper presented here focuses on the production of SiMn at Mogale Alloys.The high-level process flow at Mogale Alloys is summarized in Figure 1, which details the raw material input and the products produced by the two 20 MVA furnaces. SiMn is produced by carbothermic reduction of manganese-bearing raw materials from four different sources, namely Wessels, Mamatwan, and UMK ores, and BHP sinter feed. The carbon sources are bituminous coal from Forzando and Msobo, local suppliers in Mpumalanga."

Nov 1, 2018

By B. M. V. Baloyi, D. Mchabe, D. Chetty

South Africa accounts for the largest global manganese ore production share, primarily from its Kalahari Manganese Field deposit. Despite this, domestic smelting is beset by energy constraints, resulting in most ore being exported for smelting. Mintek is investigating energyefficient pathways for ore reduction, specifically undertaking prereduction tests to reduce energy consumption for manganese smelting. The present contribution considers the effect of methane, anthracite, and holding time, at a fixed temperature, on the extent of reduction of Mamatwan-type ore, primarily from a mineralogical perspective. In particular, the aim was to carburise the monoxide Mn phase to Mn carbide, as this is less energy intensive than producing metallic Mn from the monoxide. Based on thermogravimetric test results, the ore and products from three experiment sets were analysed using X-ray diffraction and scanning electron microscopy to assess the phases and textures present. The findings show that carburisation of manganese monoxide and its equivalents is most advanced under conditions of 8% anthracite, 10% methane, and 60 minutes of holding time, thus confirming with the thermogravimetric data. These results show promise for reducing energy consumption for Mn smelting in ferromanganese production.

Mar 4, 2025

By E. Saari, B. Musuku, K. Jansson

The quality of the concentrator plant process water is crucial for high performing mineral flotation circuits. Significant metal recovery and concentrate grade losses have been noticed particularly in more closed water loops. The recovery and quality losses have started to emerge mainly with decreased freshwater usage and because of changes in tailings management towards tailings thickening, paste, or dry stacking. These changes result in shorter, closed water loops with a rapid build-up of harmful components with negative impact on the beneficiation process. Consequently, water quality has a direct link to decreased product value and sales returns. Complete cleaning or water blending might not be the right way to achieve high recovery and high-quality products. Instead, the key is to understand what kind of water qualities are needed for the flotation of specific minerals. In this study harmful substances in various plant water streams were removed and/or modified by pilot-scale dissolved air flotation. Batch-scale mineral flotation tests with the untreated and treated water were then performed by using fresh ore samples and the plant’s own laboratory flotation procedure. The results indicate that because of dissolved air flotation, the mineral flotation recoveries were enhanced by 1‒3.3%. Keywords: Mineral recovery, metal recovery, mineral quality, process water, concentrator, beneficiation, mineral processing, flotation, process water treatment

Jan 1, 2020

By T. Song, X. Wang, X. O. Xia, X. J. Luo, B. Chen

Interparticle breakage is the main crushing mode of an inertia cone crusher according to its working principle and feeding condition. In this paper the breakage behaviour of an inertia cone crusher is investigated, based on energy controlled compression combined with the vibration theory, rather than geometry controlled compression (form conditioned) which plays a major role in conventional eccentric cone crushers. The effect of feeding and operating conditions on breakage behaviour was described quantitatively from the perspective of energy consumption and product size distribution. The influence of feeding conditions, discharge size settings and vibration exciter speeds on the crushing process and product quality has been studied according to the results of laboratory crushing experiments. The results of the experiments show that the particle size of broken products becomes finer with the decrease of a discharge gap within the gap range selected by the experiment. The product size increases significantly when the gap approaches the upper limit of 6 mm. The variation of eccentric speed has a more prominent effect on reducing the product size compared with the change of discharge gap. The change in product size is not apparent when the eccentric speed rises to a certain level. The throughput of an inertia cone crusher is sensitive to the change of discharge gap, which increases linearly with the discharge gap and decreases with the eccentric speed. The change of feeding conditions has little influence on the crusher throughput. Keywords: Inertia cone crusher, interparticle breakage, energy consumption, product size distribution

Jan 1, 2020

By P. J. H. de Graaf, S. D. N. Wessels

"Rio Tinto’s Western Australian expansion, combined with mining within structurally complex geology and increasingly below the water table, presents challenges in effective slope management to ensure safe and economic mining.The Geotechnical Management System (GMS) was developed by Rio Tinto Iron Ore (RTIO) to manage geotechnical risks identified during the design process and implementation, and to ensure feedback based on the ‘as-found’ conditions. The GMS utilizes a risk-based approach to geotechnical risk management and is centred on the geotechnical risk and hazard assessment management system (GRAHAMS). GRAHAMS is used to assess pre- and post-control risk for future potential risks (planned slopes), current risks (as-built slopes), and actual geotechnical hazards (realized risks) identified in the pit. This serves as a core operational risk management tool in identifying and prioritizing key risk sectors and management of critical controls. The system’s database reporting functionality supports effective communication of operational risks to operational personnel, as well as reporting the risk profile across operations to management.A rigorous engagement process between design engineers and sitebased engineers is implemented to ensure that key design assumptions, limitations, risks, and opportunities are understood by the site teams. This information, together with mine plan schedule details, is used to assess the design risk and develop appropriate controls. These controls typically include slope performance monitoring and slope reconciliation. The design feedback loop is closed through sharing of key slope performance and reconciliation data with the design teams.The GMS has been successfully implemented in RTIO pits and is fundamental to successful geotechnical slope management. Improved characterization of design assumptions has allowed for re-assessment of the pit design and improved hazard management in high-risk pits. The GMS, GRAHAMS, and other processes reduce the incidence of unexpected slope instability. Improved understanding of rock mass conditions has allowed for economic optimization through redesign of slopes, allowing for an improved understanding of risk and fewer unexpected conditions (surprises), hence an increased realized value."

Jan 1, 2016

By K. M. Primrose

Electrical tomography has developed rapidly over the last few years in its sophistication and practical use to enable three-dimensional information on the distribution of phases within flowing mixtures to be observed1. This paper reviews the current state of application from the industrial perspective, drawing on applications case studies based on scaling studies in the laboratory right through to installations on plant. In the laboratory, applications have looked at scale-up of mixing2 processes involving gas-liquid and solid-liquid suspensions3 with a particular interest in verifying computational fluid dynamics simulations or in checking scale-up design4,5. In the processing plant, the circumstances are usually bespoke and may range from simple detection of the degree of homogeneity of a flowing mixture through to the need to measurement a sophisticated batch process such as crystallization, sedimentation, filtering and drying. Examples drawn from the chemical and pharmaceutical industries will be presented and related to the benefits that can be gained through application of the method.

Jan 1, 2008

By K. E. H. K. Ishak, S. R. M. Zan

Cement production requires significant energy, and entails high costs and CO2 emissions. This is because the clinker requires very fine grinding. Grinding aids can improve production and fineness and decrease energy consumption by reducing the agglomeration of particles and protecting the balls and liners in the mill. In this study we compare the effects of three different grinding aids on clinker grinding using a ball mill. A commercial grinding additive, triethanolamine (TEA), and two industrial grinding aids (GAA079 and GAA088) were compared by ball milling tests, with additions of 0.05, 0.25, 0.50 and 1.00 wt%. The industrial grinding aids were characterized using gas chromatography-mass spectrometry (GC-MS). Particle size and morphological analyses were performed using SEM and XRD. The best results were obtained with 0.25% GAA088, which has a higher active component of diethanolamine isopropanolamine (DEIPA) than TEA. The unique combination of TEA and DEIPA in GAA088 enhances grinding efficiency and significantly improves the particle size distribution compared to TEA alone.. The grinding aids produced smooth rounded particles, which have a smaller specific surface area, enhancing the quality of the cement. XRD showed no significant structural distortion with or without grinding aids, and it was also found that the grinding aids helped decrease ball coating during grinding. The use of grinding aids can significantly improve clinker production and fineness while decreasing energy consumption, which can help reduce the costs and CO2 emissions associated with cement production.

Sep 6, 2023

By S. Stuurman

Inorganic acids such as sulphuric acid have found use together with certain reducing agents in leaching of copper-cobalt oxide ores. These reagents are not ideal due to the adverse effect the inorganic acids generally have on the environment and the high costs of the reducing agents. In this study a copper-cobalt oxide ore from the Central African Copperbelt was leached in two different environments; sulphuric acid in conjunction with hydrogen peroxide as a reducing agent and tartaric acid. The effects of acid concentration, reducing agent concentration, and temperature were independently determined for both leaching environments. The sulphuric acid concentration was varied between 0.4 M and 1.2 M and the concentration of hydrogen peroxide between 4.0 M and 6.5 M, while the tartaric acid concentration was varied between 0.15 M and 0.35 M. The temperature was varied between 20°C and 50°C. The results showed that the extraction of both copper and cobalt increased with sulphuric acid concentration, reaching a peak at approximately 0.8 M and then decreasing at higher acid concentrations. A similar increase and decrease in metal extraction was observed when the reducing agent was increased. In leaching with tartaric acid, the extraction of cobalt was much higher than that of copper, although extraction of both metals increased with acid concentration. Additions of small amounts of hydrogen peroxide were found to increase cobalt extraction in tartaric acid but had a minimal effect on copper. An increase in the solution temperature had a significant effect in the organic acid environment, with the effect on cobalt extraction being much more pronounced than on copper.

Jan 1, 2014