Search Documents

By G. F. Balderson

In response to the written contribution made by G. J. C. Young to the above paper, I would like to make the following points. Paragraph 1 The build-up of oxidized coatings on cone surfaces has not been a problem in other applications similar to that at President Steyn. The following companies have commented.

Jan 1, 1982

By C. O. Aksoy, G. G. U. Aksoy, A. Fisne, I. Alagoz, E. Kaya

Coal produced in underground mines is transported to the surface by means of conveyor belts throughout long roadways. The combustion of belts puts a large number of employees at great risk. Underground collieries differ from other underground mines -due to the combustible nature of the product. The most prevalent cause of belt fires in underground coal mine is spontaneous combustion due to oxidation of the coal, which also enables the conveyor belt to burn over time. In 2014, a belt fire in an underground coal mine in Manisa-Soma, Turkey caused 301 fatalities. A study has been conducted on this accident for approximately 3 years, consisting of combustion tests in a purpose-built research gallery, comparison of the test results with mine records of the accident, and CFD modelling of the mine environment. The intensity of the fire was sufficient to redirect the air flow underground, causin large amounts of toxic gases to fill almost the entire mine in approximately 15 minutes. It is recommended that CFD analysis be used in planning emergency action strategies in underground mines.

Dec 13, 2023

By P. R. Jochens, D. D. Howat, C. W. Wolhuter

Prof D. D. Howat (Member): I am a man with a grievance this afternoon. The other authors of the paper entered into a conspiracy to ensure that I presented the paper, and finally even had the audacity to say that this was the least that could be expected from me as I had done so little of the other work. Looking at the distinguished audience here that includes some figures who have forgotten more about cement that some of us have ever learned, I realise how right the other authors were. I feel very much cast in the role of the fool who was pushed in where angels fear to tread. I hesitate to say, Sir, that I would not use the word angels in any definition of the authors of this paper. In presenting the paper, may I try to put forward a few simple points about cement that are probably as little known to the majority of the audience as they were to me-at least until very recently. Concrete, made by mixing Portland cement, sand, crushed rock and water is the most widely used constructional material in the world. Generally the production of actual Portland Cement is about two-thirds that of steel and by the time this is formed into concrete the total is about five times the world tonnage of steel produced. A very rough approximation suggests that world consumption of concrete is about one ton per person per annum. Apart from fresh water mankind consumes no other material in such quantities. What mankind originally required was a mortar to be used for joining blocks of stone or bricks. Such mortar was originally made from limestone burned in a kiln and then mixed with water. Production of mortar of this type began over 5,000 years ago. Some samples from pyramids in Egypt have shown this mortar to be in good condition although over 4,500 years old. The progress of technological development was very slow until 1824 when an English bricklayer, Joseph Aspidin, patented a new mortar material which he made by burning limestone and clay together in his kitchen stove. Aspdin called his product 'Portland Cement' because, in colour, it resembled a well-known building stone quarried in the Isle of Portland on the south coast of England. Aspid's same types of raw materials are used today in modern cement production and the product is still referred to as Portland cement. A lime-containing material such as chalk or shell and a clay-type material such as shale, slate or clay itself, are mixed in the required proportions, ground and fed to a kiln where the minimum burning temperature is about 1,500°C. The raw materials react to form hard chunks of a material known as 'clinker'. About 5 per cent of gypsum is added to the clinker and the mixture is then ground to a very fine powder, the function of the gypsum being to control the rate of setting of the concrete. The key oxides in cement production are lime, silica, alumina and iron oxide. The possible reactions occurring during and the products of the burning process are shown in Table I.

Jan 12, 1968

By S. Fuchida, Y. O. Zubair, C. Tokoro

Mining of As-bearing minerals had resulted in the release of arsenic species predominantly As(III), which is known to be more toxic, and undue exposure to it is detrimental to human organ systems. Many materials have been examined for As(III) removal, but it is still challenging to advance sustainable materials for effective removal of As(III). In this paper, a more eco-friendly and superparamagnetic Fe0-Fe3O4 composite was synthesised and evaluated for heterogeneous catalytic oxidation and removal of As(III) with peroxymonosulfate (PMS, KHSO5). The kinetic removal studies showed that removal of As(III) was probably through a chemical process and the Elovich model best represented the experimental data. The removal capacity for As(III) on Fe0-Fe3O4 with PMS (1.76 mmol/g) is superior to that without PMS (0.83 mmol/g). Combined results from XPS and ESR showed that As(III) was fully transformed to As(V) through catalytic oxidation by Fe0-Fe3O4/PMS and afterwards enhanced its removal. The removal mechanism of arsenic was ascribed to the formation of outer-sphere (electrostatic attraction) and inner-sphere complexes. The adsorbent can be separated easily from water due to its excellent magnetisation (64.5 emu/g) and also has good reusability potential as more than 85% of the initial concentration of As(III) was immobilised after five consecutive cycles. Keywords: Arsenite, Fe0-Fe3O4 composite, catalytic oxidation, removal mechanism

Jan 1, 2020

By B. Oladipo, E. Govender-Opitz, T. V. Ojumu

Bioleaching, one of the several important processes of biohydrometallurgy is an accepted technique for the extraction of desired metals from sulphide ores. Although the mechanism is well understood, the slow metal extraction rate due to passivating layer and ferric ion precipitation, especially in a typical chalcopyrite leaching, impact negatively on the overall efficiency of the process. Iron precipitates are common in many biohydrometallurgical operations and these precipitates represent the exit route for undesired iron, alkali ions or sulphate ion from the processing circuit. While there have been reports on approaches to slow the formation of these precipitates by manipulation of various operating conditions such as pH, redox potential and temperature, the precipitates become highly significant over the long term in the continuous operation of bioleaching and may render heap impermeable. Although there is evidence supporting the nature of the passivation to be precipitates of iron, their scavenging mode of reducing extraction efficiency is still not well understood. This paper thus discusses iron precipitation in biohydrometallurgical processes, including its formation and significance on bioleach processes. The paper also details the associated passivating species identified with heap bioleaching of sulphide minerals and provides some insight into sorption mechanism that limits metal recovery in a typical bioleach operation. Keywords: Iron precipitation, bioleaching, chalcopyrite, passivation, jarosite, metal sorption

Jan 1, 2020

By A. J. Raubenheimer

The most important criteria in the selection of mining equipment (mining conditions. operational performance, engineering design, manufacturer's involvement, and financial considerations) are discussed in turn. Some mention Is made of the equipment population In South African collieries. and it is pointed out that both the manufacturer and the mine operator should take due cognizance of future trends in equipment.

Jan 1, 1983

By J. A. Theron

"This paper provides guidelines on performing mass and energy balance modelling involving coal and coal derivatives. Usually, the inputs to a pyrometallurgical process would be specified in terms of elements and compounds. Reliable thermochemical data is more widely available for species involving uniquely defined, relatively smaller molecules. However, in the case of coal, the molecules are extremely large and not uniquely defined. Consequently, modelling processes involving coal and its derivatives have several potential pitfalls. These are outlined in the present paper. The main findings are as follows:•,Coal proximate analysis should not be regarded as absolute; it could vary with several parameters, including heating rate •,For modelling, the use of ultimate analyses should be considered a preferable option to proximate analyses, where, ‘fixed carbon’ and ‘volatiles’ are not defined in terms of chemical composition •,Significant errors could be made if the larger molecules are neglected during calculation of the calorific value (CV) of coal gas (the gas liberated when coal is heated in the absence of oxygen) •,For elemental analyses, the oxygen content (which is calculated by balance) should be checked to ensure it is within the expected range •,For representation of sulphur in coal, double-counting due to SO3 in the ash analysis should be avoided •,Potentially, oxygen in coal could be represented as O2, H2O, CO, or CO2; however, use of some of these species without considering the experimentally determined gross CV results in significant errors in the energy balance. If coal enthalpy is calculated from elemental analyses without correction, representation of coal oxygen as H2O(l) gives reasonable accuracy (up to 6.9% error for a set of South African coals). Coal volatiles could be represented by a complex mixture of compounds, even using different oxygen-containing species than the abovementioned four, provided the enthalpy is corrected •,It is recommended that an ‘enthalpy correction value’ is incorporated in energy balances involving combustion, devolatilization, or conversion of coal and coal derivatives, e.g. coke, char, or tar. That would imply that proximate analysis, elemental analysis, as well as the gross CV would be required for all solid or liquid coal-derived substances being modelled. No other correction due to the form of carbon being different than graphite should be used, as that would imply doublecounting some effects."

Jan 1, 2014

By S. A. Villalobos, F. A. Villalobos, and L. E. Aguilera

Rockburst events have been a serious problem for many years in many mines worldwide, and in particular at El Teniente mine in Chile. El Teniente is the largest copper mine in the world, located in the Andes Cordillera where high stress levels are present due to intensing mining activity in addition to complex geology. Consequently, the study and management of the rockburst threat are necessary. In this work, the case of the Diablo Regimiento (DR) mine within El Teniente is studied. The energy capacity of dynamic support systems is determined for different tunnel geometries based on two kinetic methodologies, using data from DR. Initially, rockburst potential is determined by means of a stress analysis around different tunnel geometries through the boundary elements method. In the first methodology a yielding zone (YZ) is estimated for each excavation geometry using the finite element method FEM. The second methodology involves the definition and determination of a critical strain energy (SE) around each excavation geometry using a FEM numerical analysis. In both cases, peak particle velocity PPV is estimated by a scaling law, which is subsequently adjusted due to tunnel amplification effects. According to the results, and knowing the working energy capacity applied in DR mine, it was found that the values of energy capacity for the rock dynamic supports were better estimated by the YZ-PPV approach than by the SE approach.

Sep 1, 2022

By M. H. Tyeb, C. Banerjee, A. K. Majumder

The primary requirement from a hydrocyclone is the classification of the feed solid particles. Particle classification occurs inside a hydrocyclone by virtue of the relative radial distribution of the suspended particles, based on their size and specific gravity. The particle classification behaviour in a hydrocyclone is experimentally studied in this paper. The phenomenological features of the air core at different feed solid concentrations and the distribution of the solid concentrations in the hydrocyclone are also analysed by the theoretical study of flow features in a steady Rankine vortex. Semi-empirical models for predicting the hydrocyclone performance in terms of flow split ratio, and cut size have been developed using the background knowledge of convoluted hydrodynamics. In addition, to validate the classification performance of a smaller diameter hydrocyclone, the potential of the present model is extended for envisaging the same for larger diameter hydrocyclones. A comparison between the model predicted values and the measurement data shows a good match. Keywords: Hydrocyclone, classification, Rankine-vortex, air core, modelling

Jan 1, 2020

By B. Jack, A. Vervoort

During pillar extraction, sidewall fracturing and spalling at some collieries constitute a severe stratacontrol problem. In order to obtain a better understanding of this phenomenon, a survey of pillar corner conditions before and during pillar extraction was conducted at one particular site. For the various successive mining steps, the vertical stresses on the pillar corners were calculated by use of a three-dimensional boundary element program. A significant correlation was found between the calculated vertical stress prior to the extraction of the panel and the sidewall conditions. During the extraction of the panel, a significant deterioration of the sidewall conditions at a pillar occurred only when the adjacent pillar was mined, causing an increase in vertical stress on the remaining pillar.

Jan 1, 1992

By N. J. Roodt

Mine dumps created in terms of the pre-MPRDA regime (old order mine dumps) are currently not regulated by the MPRDA, and the common law owners of such dumps are free to process them without the need to obtain the relevant rights. The MPRDA Amendment Act purports to change this position. However, the wording of the Amendment Act raises a number of problems which render the post-amendment position at best unclear and at worst absurd and unworkable. The primary concern with the Amendment Act is that, on one interpretation, material placed on the same dump at different times may be treated differently at law. Thus, parts of a dump may be subject to one person?s right while others may be subject to another?s right. Moreover, case law has generally regarded mine dumps as movable property and, by extending the MPRDA to apply to all mine dumps, the Legislature is extending the ambit of the Act to cover movable property, a scenario not contemplated by the wording of the Act (even after its amendment) in relation to applications for rights. The better interpretation of the amendments, which are not yet in force, is that they will not apply retrospectively to old order mine dumps.

Jan 1, 2010

By J. J. leR. Cilliers

ABSTRACT The recently introduced concept of negative taxation complicates estimation of the distributable profit of certain South African gold mines, and an assisted mine could operate at a working loss and yet produce an overall profit for distribution amongst its shareholders. A simple diagram is presented from which the approximate working profit or loss, taxation payable or tax credit received, and the distributable profit of an assisted mine can be estimated directly for any combination of the four main variable operational factors: tonnage milled, recovery grade, unit cost and capital expenditure. INTRODUCTION The effects on the working profits of South African Gold mines caused by changes in unit working costs, recovery grade, tonnage milled and capital expenditure are readily estimated. For normal tax- and lease-paying mines the distributable profit is related to the working profit and the latter is a commonly accepted comparative measure of the profitability of an operation. However, the recently introduced concept of State assistance in the form of negative taxation1, i.e. a tax credit, for mines with a life of less than eight years complicates such estimates. A requirement of State assistance is that an assisted mine must lower its normal pay limit by 16 to 20 per cent, and it will be possible for a mine to operate at a working loss and yet produce an overall profit for distribution amongst its shareholders. In the case of an assisted mine it is therefore necessary for management to judge the effects of changes in unit costs, grade, etc., in terms of distributable profit instead of working profit. This will require repeated calculation of tax to be paid or tax credits that will be received under the numerous possible combinations of the four main variable factors. However, with the aid of the diagram illustrated in Fig. 1, it is possible to assess at a glance the practical effect of these variables on the distributable profit of an operation not subject to tax on the normal formula, or small mine formula, with sufficient accuracy to decide whether a detailed analysis is required. USE OF THE DIAGRAM From the central point 'X' in Fig. 1, a range of tonnages milled per annum has been plotted along the north-bearing axis, a series of costs per ton milled in the northwestern quadrant, recovery grades in the northeastern quadrant, and capital expenditures in the southwestern quadrant. Starting from the tonnage milled per annum, a line is drawn east and west across the two northern quadrants up to the points where it reaches the desired cost- and grade-lines. From these points two north-south lines are drawn into the southern quadrants. A further line is drawn to the east from the point where the western north-south line crosses the desired capital expenditure. Distributable profit is read off in the southeastern quadrant where this line intersects the eastern north-south line. Every possible combination of

By S. Ramatsoma, D. N. C. Phillpotts, B. Whitehead

Changes in flotation performance have been correlated to changes in froth structure, velocity and stability. Literature has shown that when the aeration rate is varied for a specific float cell, the recovery of the valuable mineral reaches a peak which also coincides with a peak in the air recovery – a measure of froth stability. Peak air recovery optimisation methodology is a way to use direct readings of physical phenomena by froth cameras to optimise the metallurgical performance of a flotation plant. The aim of this paper is to show the transient nature of the peak air recovery value and the variety of conditions required to attain the peak air recovery on an industrial flotation plant with tight base-layer control of the feed and internal conditions. Industrial site tests that were conducted under controlled conditions showed different peak values at significantly different corresponding aeration rates during normal operation. The measured peak air recovery points corresponded to maximum PGM recovery during normal flotation, as expected. This dynamic nature of the peak air recovery point conditions has not previously been discussed in literature and indicates the need for online measuring equipment and informs the design of process control algorithms required to exploit the phenomenon for optimisation. Keywords: Froth flotation, flotation control, flotation optimisation, peak air recovery

Jan 1, 2020

By K. Basaure, S. Palma, R. L. Castro

"Mud rushes are sudden inflows of fine wet ore within underground mines; they can harm people and equipment as well as cause production delays. Block and panel caving mines are prone to mud rushes in their production levels, with mud flowing from the drawpoints. Different mines have developed methods to control drawpoint conditions and thus perform safe ore extraction. The aim of this study is to develop a decision matrix and apply it to samples from drawpoints for the Diablo Regimiento mine, Codelco, El Teniente Division (Chile). The Abrams’s Cone was used to perform slump tests on mud samples and characterize their consistency by setting the saturation degree and packing. The unconfined strength for different saturation degrees and packing was then evaluated. The results show that conditions for fluid response in slump tests correspond to conditions for low strength in unconfined compression tests. We also found the water content value at which the flowing consistency changes from plastic to soft behaviour according to the slump test classification for each sample. This value varied between 12.2% and 16.9%, depending on the sample tested. Finally, a fluid security factor was defined in order to design an extraction pattern for the samples tested, based on the water content. We conclude that a very densely packed ore is not prone to flowing. The flow properties depend strongly on the specific properties of the ore tested, and consequently a specific criterion should be developed for different types of ore at a particular mine. The criterion developed for Diablo Regimiento ore provides critical water content values from 11% to 15%, depending on the ore type. IntroductionBlock/panel caving has the lowest cost and the highest production rates of all underground methods (Heslop, 2000; Hubert et al., 2000). Good management of the risks is important to ensure the security of personnel and infrastructure. Operational risks for the method include rockbursts, air blasts, and mud rushes (Hubert et al. 2000). A mud rush is defined as a sudden inflow of mud from a drawpoint or other underground opening into the mine (Butcher, Joughin, and Stacey, 2000; Butcher, Stacey, and Joughin, 2005). Mud rushes can cause dilution, production delays, and damage to equipment as well as injuries and fatalities. The elements necessary for mud rushes are mud-forming material, disturbances, a discharge point, and water (Butcher, Joughin, and Stacey, 2000). All these elements are present in block/panel caving mines. Mud-forming material comes from ore milled by the caving process; water comes from underground and surface sources. Drawpoints in the production level are discharge points for the mud. Finally, several types of disturbance could trigger the mud rush phenomena: blasting, earthquakes, operation of equipment (Call & Nicholas, Freeport McMoRan, and Hydrologic Consultants, 1998; Jakubec, Clayton, and Guest, 2012), arch collapse above drawbells (Butcher, Joughin, and Stacey, 2000; Butcher, Stacey, and Joughin, 2005; Jakubec, Clayton, and Guest, 2012) and ore drawing (Butcher, Joughin, and Stacey, 2000; Butcher, Stacey, and Joughin, 2005; Call & Nicholas, Freeport McMoRan, and Hydrologic Consultants, 1998; Jakubec, Clayton, and Guest, 2012)."

Jan 1, 2017

By G. R. Marchant, B. K. Loveday

"A mathematical model has been developed for flotation circuit simulation. This model was designed to investigate the effect of varying the circulating loads and to determine whether an improvement in overall efficiency could be gained by a size separation prior to flotation.Model parameters were obtained by regression to plant data. Highly correlated parameters in the model were combined to reduce the number of parameters so that the need for excessive data gathering was eliminated. Mass balance smoothing was used to obtain a consistent data set for regression.The results of the simulation indicate that for the same grade of concentrate, an increase in copper recovery of 0.6 per cent may be Possible by increasing the circulating loads. The results of the simulation also indicated that recleaning of the plus 200-mesh material may be beneficiaL."

Jan 1, 2014

By H. M. Friede

Discussion of the above paper by A. SIFF The steely nature of the Iron Age objects mentioned in Dr Friede's paper point to two hypotheses. (1) The African iron workers were conversant with the art of direct steel manufacture. (2) They were less knowledgeable of the art of the production of carbonless iron. In this context I cannot but quote T. A. Wertime.

Jan 1, 1980

By J. Meintjes

by I. J. BARKER and A. B. STEWART J. MEINTJES I read the above paper with considerable interest. I would like to point out, however, that it is fallacious to conclude that the adverse effects of a high inductive reactance on furnace operation can be cancelled by connecting capacitors in series - or for that matter, in shunt - with the power supply.

Jan 1, 1980

By M. M. Bwalya, F. K. Mulenga

"SynopsisThe application of the attainable region (AR) technique to the analysis of ball milling is currently limited to batch data. This paper introduces the use of the technique to continuous milling.To this end, an industrial open milling circuit processing a platinum ore was surveyed. Samples were collected and later characterized by means of laboratory batch testing. On site, several milling parameters were varied systematically so as to collect data for modelling purposes. These paramters included ball filling, slurry concentration, and feed flow rate. After data analysis, a simulation model of the open milling circuit was developed under MODSIM®, a modular simulator for mineral processing operations. The mill was then simulated and the data generated was analysed within the AR framework.Initial findings reveal an opportunity to gain valuable insight by studying milling using the AR technique. From an exploratory perspective and inasmuch as this study is concerned, feed flow rate, ball size, and ball filling were identified as being pivotal for the optimization of open ballmilling circuits. Mill speed, on the other hand, had only a limited effect on the production of particles in the size range -75 +10 µm.IntroductionGlasser and Hildebrandt (1997) propounded the attainable region (AR) as a technique for the analysis of chemical engineering reactor systems. Results have since been produced and tested on both the laboratory and pilot scales. The method results in a graphical description of chemical reactions by considering the fundamental processes taking place in the system, rather than the equipment. From the plotted graphs, the process and the reactors can be synthesized optimally into a flow sheet.The use of the AR method still has a long way to go as far as mineral processing is concerned. For instance, several articles have reported the application of the AR technique to ball milling: Khumalo et al. (2006, 2007, 2008); Khumalo (2007); Metzger et al. (2009, 2012); Metzger (2011); Katubilwa et al. (2011); Hlabangana et al. (2012). Their main shortcoming has been the exclusive use of laboratory batch grinding data.To address this deficiency, Mulenga and Chimwani (2013) proposed a way by which the technique could be extended to continuous milling. In effect, the batch milling characteristics of a platinum-bearing ore (Chimwani et al., 2013) were used and scaled up to an open milling circuit. Then, with simplifying assumptions, an attempt was made to optimize the residence time of particles inside the mill. Later, Chimwani et al. (2014a) presented some optimization examples involving various milling parameters. The sequence of published articles then paved the way for the study of industrial milling systems with the AR methodology."

Jan 1, 2015

By D. P. Enright, D. D. Howat

Austenitic manganese-steel castings are very widely used in crushing and grinding in the' gold-mining industry in South Africa, The service life of a casting in a short-head crusher is difficult to predict because there are no clear-cut criteria by which such a judgement can be made, The addition of molybdenum and zirconium to the castings for crushers failed to result in improved performance, The results of extensive tests with through-hardened steel castings were very disappointing, mainly because of a design factor in the bowl liner. The design of the bowl liner is an important determinant of the life and performance of these castings. The extent to which the material in a crusher is reduced in size has profound effects on the consumption of metal and power, and on the effective life of a casting. Tests on manganese-steel castings in an 8 ft by 12 ft rod mill provided data on the total consumption of metal, and on the variations in the pattern and rates of wear of liners over lengthy periods. Progressive changes in the wear profiles of the lifter bars and the other liner components showed unexpected features. There are clear indications that, whereas a set of lifter bars will at first lift the charge strongly with relatively little slippage, there is a later period characterized by more slippage and greater wear on all the liner components.

Jan 1, 1980

By C. Mueller

Automation of mining operations is pushed by cost pressure and cyclical product prices. However, until now the different types of equipment were not able to communicate electronically with each other or with central computer systems. Therefore, the International Rock Excavation Data Exchange Standard (IREDES) was launched by major players in the industry. The task of this initiative is to define a ‘common electronic language’ for easy and standardized data exchange. As in other industries, this standard is expected to have significant impact on the use of automation in general and on the markets for third party components and software. The standard’s technical architecture is open and flexible for future applications. It consists of an ‘horizontal’ structure defining ‘Application Profiles’ for different types of data sets. An additional ‘vertical’ structure (‘Equipment Profiles’) implements equipment dependent definitions for each of the applicable Application Profiles. First profiles will be available for Drill Rigs. The standard bases on the XML language thus enabling easy data exchange with commercial databases. IREDES data sets may use storage media as well as networking infrastructures for information exchange. The IREDES work is carried out by the initiative members working jointly together in the IREDES work groups. It is open for participation of all interested organizations. First prototyping applications are expected to start during 2001, the first products may be available in the following year. Key words: Mine Automation; Machine Automation; Data Exchange; Rock Excavation; Standard; Remote Control; Teleoperation; Ethernet; TCP/IP; Internet Technology; Service; Quality Assurance; Control Centre;

Sep 1, 2001