Search Documents

By Danny W. Hagood

High methane liberation and mining depth were two major factors which prompted the development of a high- capacity face ventilation system at Jim Walter Re- sources, Inc., No. 4 Mine. No. 4 Mine, one of four deep shaft mines presently under development, is located approximately 50 miles southwest of Birmingham, near Brookwood, Alabama (Figure 1). The coal seams under development are located in the Warrior Coal Field and include both the Blue Creek and Mary Lee Seams, Depth of cover averages 2000 ft. (610 m) with an average total mining height of 8 ft. C2.4 m). [ ] It is generally accepted that the methane content of a particular coal increases as the overburden depth is increased [l] ; experience to date has shown that the gas condition of the No. 4 Mine is no exception to the rule. To further compound the problem, the over- burden depth, coupled with the relatively soft nature of the Blue Creek coal, has resulted in an initial layout based upon 150 x 150 ft (45.7 x 45.7 m) centers. Considering the above-mentioned mining conditions, the means and the effectiveness of the face ventilation system becomes paramount where productivity is concerned.

Jan 1, 1980

By X. K. Jiang

Upgrading molybdenite ore can be technically difficult and expensive if talc is a major impurity in the ore. The layered structure of molybdenite and talc decreases the surface specificity of floatation and suppression agents, thereby making molybdenite ore beneficiation inefficient if under some wet processing methods. However, oxidic talc surfaces may be distinct from the sulfidic or oxysulfidic molybdenite surfaces, such distinction related to electron work functions and/or densities of electron donors/acceptors sites. If such differences are present, the upgrading of finely sized molybdenite ore by dry triboelectrostatic methods may hold advantages over traditional wet methods.

Jan 1, 1999

By M. Fofana

The use of a laboratory-scale magnetic fluid-based separator for coal separations was examined. A Frantz laboratory magnetic separator was modified by fabricating new pole pieces of the appropriate geometry to provide the proper magnetic field gradients. Two separation chambers, which were constructed out of Plexiglas, were designed to fit between the pole pieces. A commercially available, water-based, ferro-magnetic fluid was used as the separating medium. The separating density was changed by varying the intensity of the electromagnet. Both batch and continuous separations were made using 0.59x0.50 and 0.18x0.15 mm coal. The results are compared to those obtained using organic liquids.

Jan 1, 1996

By J. Roth

PROLOGUE Nowadays, where production costs and energy costs are increasing and at the same time requirements in fineness and purity of industrial mineral products are getting higher and higher, industry has to look for more efficient grinding systems and developments to produce these products more economically. Therefore lots of new developments in high energy jet mill pulverizing have been made. In the main, however, these developments involved more or less just the new principle of fluidized bed jet pulverizers but not the older spiral jet mill principle. In some cases, especially in the filler industry where laminar minerals are used and higher aspect ratios are required, the spiral jet mill principle has advantages in a better delamination of these minerals. To comminute minerals down to products with a d97 < 3 µm, the specific energy consumption increases up to 2,000 kWh/t – 3,000 kWh/t or even more, depending on the grindability of the mineral. So the production of these fine materials is quite an expensive task. But jet mill grinding is and will be the most favorable method to produce micro-products and in the near future nano-products, despite the high energy consumption.

Jan 1, 2000

By M. S. Vernon, J. J. Kellar, W. M. Cross, R. M. Winter, F. J. Johnson, A. G. Pommer

Three substrates (MgO crystal, CaF2 crystal and Mg plate) were used to construct thin layers of Mg(OH)2. Various routes were used to modify these substrates, including surface hydration and sol-gel coating. In each case, it was found (by using Fourier transform infrared spectroscopy) that thin layers of Mg(OH)2 could be produced. In the case of hydrated layers, the surface morphology of the Mg(OH)2 resembles the bulk platelet shape of precipitated Mg(OH)2.

Jan 1, 2000

By G. T. Adel

The application of automatic control to mineral processing operations has been gaining momentum during recent years. Many strategies are being developed for controlling crushing, grinding and flotation circuits, however, their implementation in industrial plants is being slowed down because of the costs and difficulties in evaluating these strategies in a systematic manner. An interactive computer simulation package, developed at the University of California, provides the capability of analyzing the process dynamics of mineral processing circuits. This paper presents an overview of the simulator and its application to the case studies of grinding and flotation.

Jan 1, 1983

By Ing. Alois Adamus, Ing. Václav Pošta, Ing. Lubomír Hájek

This paper reviews experiences connected with the use of nitrogen in the Czech coal industry. Special attention is focused on the first use nitrogen In the Czech Republic, it is probably the first case of fighting a mine fire using nitrogen in all the World. Discussion dwells on the present-day use of nitrogen, its sources, consumption, technological equipment, and the theoretical evaluation of nitrogen flushing.

Jan 1, 1995

By Boris M. Vorobjev

The paper in question discusses a wide range of topics related to computerized coal mine monitoring systems starting with the history of development and application of computerized monitoring coal mine systems and finishing with modern trends in the design and updating of such systems. The paper focuses exclusively on methodological and technical aspects of computer-based coal mine monitoring systems and their applicability in both surface and underground coal mining operations.

Jan 1, 1989

By James J. Scott

Shale formations are the Nemesis of the Mining Engineer. Shales react to changes in environment in the most unusual and unpredictable manner. Increase in temperature may cause spalling, increase moisture and compression induced fractures may occur, and if a full face is exposed it may deteriorate due to atmospheric exposure. Combine only small amounts of shale in layered fashion with hard brittle competent rock and the whole structure may be fractured and fail due to stresses generated in and around the shale. In this paper the author will discuss failure mechanisms encountered under various field conditions and remedial action which may be employed by the engineer.

Jan 1, 1969

By F. Kennedy

Consolidation Coal Co. (Consol) supports an active research and development effort to improve the safe, productive mining of coal and to use coal in an environmentally acceptable manner: Attention will be focused on degasification of coal seams, continuous coal transport systems, earth sciences activities, and coal combustion. Brief mention will be made regarding the SO2 emissions control programs. The research program constitutes about 1 % of Consol coal sales, which positions Consol as the preeminent coal company supporting broad-based research addressing the full spectrum of the various problems associated with using the nation&apos;s abundant reserves of economical, readily available fuel.

Jan 1, 1990

By Robert Marks, Enrico Dal Negro, Richard Schulkins

"In July 2012 construction started on the Grosvenor project, a five million tonne per annum underground longwall mine planned for Moranbah in Central Queensland. Grosvenor is located immediately to the south of the existing Moranbah North mine which has been in operation since 1998. EPBM technology is being used for the first time in Australia for excavation of a coal drift. The TBM was used to build two drifts on the project, one for the coal conveyor which will transport to surface, and another for people and equipment to access the underground once the mine’s operational (as shown in figure 1). The TBM will pass beneath a steel archway roof that has been installed at the drift’s entrance and begin drilling into the ground to build the seven metre diameter tunnel, descending at an angle of one in eight until it reaches the depth of the coal seam approximately 160 metres below.INTRODUCTION AND BACKGROUND The first TBM used in a coal mine was in 1962, a Wohlmyer, in Westerholt, Germany. A further 75 km of tunnels were excavated in coalmines within Germany between 1971 to 1983. This paper will review the Grosvenor Mine project (Grosvenor) owned by Anglo American Metallurgical Coal (Met Coal) includes the construction of a new underground coal mine and surface facilities on the northern boundary of the town of Moranbah in the Central Queensland Bowen Basin coal precinct. The contract to undertake the underground development works was awarded to Redpath in 2012. The scope of the Grosvenor Project was to construct temporary office and workshop facilities, install 2 portal arches, backfill boxcuts and infrastructure, excavate by EPBM method 967 m of 1:6 gradient Conveyor Drift and 1,258 m of 1:8 gradient Transport Drift, development of 2,520 m of pit bottom area roadways and development of 10,550 m of the first longwall tailgate. In the following figures 2 and 3, is possible to see the aerial view of the job-site."

Jan 1, 2016

By Kadri Dagdelen, M. Waqar Asad

Cement production involves the processing of raw materials that contain - Si02, A1203, Fe203, CaO, MgO, LOI (loss of ignition), S03, K20, Na2O, Ti02, P2055 and Cl- to produce the synthetic mineral mixture called "clinker". The use of other additives - sandstone, flyash, iron ore, and clay - is also mandatory in order to achieve the optimum blending requirements of cement. However, the use of these additives needs to be minimized due to their significantly higher costs ($/Ton). This paper presents a mixed integer programming (MIP)-based optimum quarry scheduling algorithm, which is used to generate quarry plans, satisfying geometric and production capacity constraints while providing minimum cost/optimum blend of raw materials mix to a cement plant. The benefits of this new methodology are demonstrated on a case study.

Jan 1, 2002

By W. Lin, E. Heuze

This paper focuses on tests performed on sandstones and shales from four gas wells in the Mesaverde formation. A previous document showed a comparison of the static and dynamic laboratory moduli. This publication describes how field velocity logs were used to derive field dynamic moduli. A 3-way comparison was then performed for these stiffness properties; the results show no agreement between the three sets of values. Differences between dynamic stiffness coefficients from the field and the laboratory exceed 200%; differences between static and dynamic coefficients range up to 600%. In turn, this indicates that a reliable method of estimating mechanical rock properties for hydraulic fracturing design has not been established, and that such a task should be pursued.

Jan 1, 1986

By K. A. Natarajan, M. K. Yelloji Rao, P. Somasundaran

The bacterium Thiobacillus ferrooxidans triggers the surface modification of sulfide minerals to provide hydrophilicity or hydrophobicity for the flotation of sphalerite and galena. The effects of initial cell concentration, period of biotreatment and pulp density on the floatability of the minerals are discussed. With galena, flotation enhancement obtained through sulfuric acid treatment was retarded by biotreatment at all cell concentrations due to chemical effects. Such a decrease occurred for sphalerite only at cell concentrations sufficiently high for bacterial attachment to the mineral surface. The variables affecting surface modification (and, thus, flotation response of the minerals) include the cell concentration used for bacterial conditioning, the period of biotreatment and the pulp density. Although bacterial growth during biotreatment was observed even in the absence of nutrients, such growth was more common in the sphalerite suspension than in the galena suspension. Cell protein estimations suggest that more cells are attached on galena than on sphalerite. Probable reaction mechanisms associated with bacterial modification are discussed.

Jan 1, 1993

By K. V. K. Prasad

Stochastic simulation has been routinely used for performing risk and sensitivity analyses in a variety of fields. The commonly used means of generating the simulations has been the Monte Carlo approach, which usually employs a Simple Random Sampling (SRS) scheme of the variable distributions. This method is prone to sample clustering and requires a large number of samples to represent the distribution faithfully. This can become problematic for simulating complex processes where it is impossible to run an arbitrarily large number of replicate simulations. The Latin Hypercube Sampling (LHS) method uses a stratified sampling approach that assures representation of the input distributions for any given number of samples. In this paper the LHS and SRS approaches are compared, using a petroleum resource estimation example.

Jan 1, 1994

By Hajime Miki, Michael J. Nicol

Relatively simple techniques have been developed which enable the electrochemistry of sulfide minerals to be studied with particles varying in size from above 100 pm to less than 1 pm. Both oxidative and reductive processes have been studied wing the minerals pyrite, arsenopyrite and chalcopyrite. It has been shown that it is possible to completely oxidise or reduce the minerals during a single voltammetic sweep. The resulting voltammogram produces peaks which are characteristic of each mineral and can be used to qualitatively identify the minerals. In the case of chalcopyrite, it has been demonstrated that the charge involved in the anodic oxidation can be quantitatively related to the amount of copper dissolved. Quantitative information can be obtained using peak fitting techniques. Interesting differences in the behaviour of the minerals in sulfuric and hydrochloric acids have been observed, particularly in the case of pyrite for which a second major peak is obtained which has been attributed to the oxidation of elemental sulfur in the presence of chloride ions. The technique offers the possibility of providing mineralogical information of individual particles based on an electrochemical voltammetic finger print.

Jan 1, 2005

By Michel Dagbert

The determination of the precision of reserve estimates (tonnage, grade, quantity of metal) for an entire deposit or a large block in a deposit has received some attention in the early developments of geostatistics. A general formula to derive the estimation variance of any linear combination of a large number of sample values can be found in any geostatistical textbook like David (1977) or Journel and Huijbregts (1978). A particular case of this general formula is of course the kriging of the entire deposit. However, besides the technical difficulty of dealing with many samples the application of this formula necessitates the knowledge of the covariance between any two samples in the deposit. This is quite unrealistic in the usual case of limited stationarity where the assumption of a covariance or a variogram just function of the distance vector between two samples is only valid for samples within the same area of restricted size.

Jan 1, 1982

By Kalliat T. Valsaraj, Louis J. Thibodeaux

A mathematical model is described for the transfer of hydrophobic compounds from aqueous to an immiscible organic phase using fine bubble aeration; the process otherwise known as "solvent sublation" an adsorptive bubble separation process. The limitations of the model are explored by simulating experimental results both for a batch scale process and a continuous process. The qualitative predictions of the model with respect to the influence of the organic layer (mineral oil) are tested by performing experiments using chloroform and 2,3,6-trichloroanisole as hydrophobic compounds in the aqueous phase. The continuous process is seen to be limited by the requirements of fine bubble generation and the ratio of influent feed rate to air flow rate.

Jan 1, 1989

By Herbert Pöllmann

The mineralogical and chemical compositions of various waste materials undergo different reactions when treated thermally The heavy metal contents can be bound to stable phases. These minerals are called reservoir minerals. The main property of these minerals is the stability in their geochemical surrounding containing the heavy metal cations and anions. Examples for these minerals are apatites, spinels, garnets, perovskites and also water containing minerals like ettringites, metal-metal-hydroxi salts, jarosites and zeolites. When the chemical compositions of different wastes are mixed according to the compositions of the new formed minerals, a probable reuse of these wastes can be obtained. The use of waste incineration ashes for the production of cementitious binders and the use of flue gas desulfurization products for cement additives are shown. Also the transformation of highly contaminated materials into stable reservoir mineral assemblages are shown including the study of stabilization and immobilization techniques.

Jan 1, 1998

By Rodolfo V. de la Cruz

This paper describes the development of a new method and device for determining the in-situ mechanical properties of rock masses. The method involves a self-recording mechanical deformation gauge for sensing-recording she deformation of the borehole wall when loaded hydraulically. The self-recording feature of the gauge eliminates the difficult technical problem of transmitting signals over very long cables for measurements at great depths. Adopting a mechanical gauge instead of electronic, electrical, optical or grid techniques eliminates delicate instrumentation and installation problems. Moreover, mechanical gauges are inherently rugged and suitable for use in severe borehole conditions including very high temperatures. The technique was tested in limestone, basalt and granite specimen. The calculated mechanical property values for 1 the tests agree with those obtained by conventional testing methods. The self-recording mechanical deformation gauge has a minimum reading of 50 micro inches (1.27 x 10-3mm), comparable with electrical resistance strain gauges, capable of reading deformations over a range of 0.25 inches (6.35mm). The sensitivity, ease and accuracy of the method recommends it highly for in-situ rock modulus measurements.

Jan 1, 1980