Search Documents

By W. M. Jr. Aubrey, R. L. Stone

INTRODUCTION Most metallic minerals and some industrial minerals have a relatively high specific gravity and most have at one time or another been concentrated by gravity methods. The principles of gravity concentration are straightforward, well documented and easy to understand, but in practice there are many pitfalls that await the engineer in the development of an integrated flowsheet. Gravity concentration equipment has a long history of use and there is a great diversity available. The equipment is capable of treating material over a broad size range, only falling off in efficiency in the very fine sizes. Gravity concentration is also inexpensive, generally free of environmental problems, and commercial equipment can process large tonnages of ore with a minimum of capital cost. As might be expected of an efficient and low cost process, the bulk of the tonnage quickly and inexpensively. Another obvious application is treating mineral deposits such as hematite and manganese ores that are sufficiently liberated after a minimum of crushing to allow production of a coarse concentrate that will meet market specifications. Except for hand picking and mechanical sorting, there is no competing process on coarse size material. Conversely, it is sometimes obvious that gravity concentration does not warrant consideration. Examples are ores that require very fine grinding to attain liberation, for ores where the minerals of interest have a gravity similar to the gangue, and ores that are strongly magnetic. Actually a mineral processing engineer may not know if gravity is the best way to concentrate an ore, but he should have little difficulty recognizing when gravity concentration deserves consideration based upon specific gravity differences and liberation gravity concentration has wide use. size. His challenge then is to At times its selection as the identify and test the applicable primary concentration process is processes, to develop a obvious. Low grade placer deposits metallurgical balance and flowsheet of tin, gold and beach sands usually for the best process, to estimate are only profitable because gravity production rate over the life of concentration is able to throw away the deposit and to make equipment

Jan 1, 1986

By Peri Mehling, Allister Brown

Environmental regulations concerning the processing of gold ores and the treatment and disposal of spent process solutions range from rigid standards in some locations to site specific options in several other jurisdictions. This paper examines the regulations and policies in two North American jurisdictions. Emphasis will be placed on the mill process and waste stream treatment and disposal, and implications for environmental impacts. Case examples of mine licence requirements will be discussed, with brief descriptions of individual treatment and disposal systems. Policies and environ- mental regulations within each jurisdiction will be examined in terms of potential environmental protection.

Jan 1, 1987

By Milton E. Wadsworth, Ximeng Zhu

Impurity metals can markedly influence the anodic dissolution of gold in the presence of cyanide. Several important findings related to the influence of lead are reviewed and some new observations presented. Based on the effect of pH, the scan direction, and voltage, it may be shown there are three separate voltage regimes where lead influences the anodic dissolution of gold. These are related to Pb°/ HPbO2, Au-Pb /HPbO2, and HPbO2/PbC2; oxidation-reduction reactions which provide low resistance paths for electron exchange. The gold dissolution rate was determined by direct solution analysis and is compared to the rate implied by electrochemical measurements.

Jan 1, 2005

By Pramod C. Thakur

Sixty countries around the world mine about 5000 million tonnes of coal annually and simultaneously produce nearly 25 million tonnes (36.8 Gm3) [One tonne of methane at a temperature of 15°C and a pressure of 760 mm of mercury has a volume of 1471 cubic meters.] of methane. Many of these coal mines are very gassy and require methane drainage prior to mining as well as during mining. In spite of significant differences in the geology and reservoir properties of the coal seams, several methane drainage techniques have found universal application. The paper describes various techniques currently in use and their efficiency in recovering methane from mines. It appears that the application of state-of-the-art techniques, developed mostly in the U.S.A., can considerably increase the efficiency of methane recovery and improve the safety of mines throughout the world.

Jan 1, 1997

By B. Denby, R. Hollands, S. Cooper

Augmented Reality (AR) is a technology that can be used to mix computer-generated images of data with views of the real world. The University of Nottingham is developing AR technology in a major research project which can be used to assist mining companies in visualising complex mine data whilst out in the field. The technology comprises of integrated GPS surveying technology and electronic orientation devices to provide location and viewing information, video capture via digital camera and portable computing hardware to overlay 3D models on views of the real world. The paper describes the concepts of the technology in some detail and concentrates on the possible applications of this in the surface mining and exploration industries.

Jan 1, 2002

By Milton E. Wadsworth, M. Ken Han

The kinetics of leaching of galena in hydrochloric acid solutions with sulfur dioxide gas have been investigated experimentally. The leaching method is then applied to complex sulfide concentrates to evaluate its selective leaching capability and to develop a new hydrometallurgical lead extraction process based upon the method. The leaching reaction follows a linear rate with an activation energy of 61.9,KJ/mole. The rate Is of first order with respect to the product [H+] [Cl-] . Excel lent selective leaching capability f s demonstrated and an attractive hydrometallurgical process flow sheet is proposed.

Jan 1, 1989

By Richard R. Klimpel

This article introduces the basic definitions and philosophy behind process hazard evaluation procedures and the determination of risk as being a function of accident probabi1ity and accident consequence. The general concepts of good engineering practice and predictive hazard evaluation are discussed. The most commonly employed methods used in the processing industries are reviewed with an eye towards briefly presenting what each method offers as far as information, time and resources required, etc. Some initial references on the actual practical use of each technique in the processing industries are also given.

Jan 1, 1991

By S. Ouyang

The four most important parameters controlling the flow of as in coal are the gas content, permeability, diffusion coefficient and clear characteristics. Estimates of these and, more importantly, a good knowledge about the variations in their values over time are important for proper simulation of long-term gas production. This paper describes experimental techniques for the estimation of diffusion-coefficient and permeability values, along with their time dependency under simulated in situ conditions. It is shown that the permeability and diffusion-coefficient values are not constant, as they are usually assumed to be. There is a significant variation in their values, probably as a result of changes in the microstructures of coal associated with release and flow of gas. Finally, a technique to estimate clear parameter is presented.

Jan 1, 1997

By K. R. Weller, U. J. Sterns

The goal of most in-plant studies is to identify factors that limit overall plant performance. A major finding from such studies is that interactions between unit operations are always important, usually specific for a particular ore and plant combination, and are one of the limits to plant performance. Computer simulation based on process models developed from in-plant studies is a useful tool for identifying limits to performance and for estimating the effects of proposed changes at both pilot and industrial plant scales. Examples involving interactions between comminution and various separation and agglomeration processes are presented, and directions for future development discussed.

Jan 1, 1989

By Winfield G. Wright, Greg P. Meeker, Philip L. Verplanck, Douglas B. Yager, Dana J. Bove, M. Alisa Mast

A really extensive acid sulfate-altered and mineralized rock in the southeast Red Mountains area is noted for its association with naturally occurring and mine-related acidic and metal-rich waters. Integrated geologic and aqueous geochemical studies demonstrate that the degree of metal mobilization and acid production in natural waters correlates well with the type of hydrothermally altered rock and structural features in which these water interact. Quartz-sericite-pyrite, quartz-alunite, and argillic alteration assemblages are associated with some of the most naturally acidic, high-metal waters in the study area; calcite-bearing propylitic rocks are related to the most pristine waters and buffer sulfate-rich, acidic waters produced by pyrite oxidation. Trace metals in natural waters are mostly derived from enargite, zinc-rich tetrahedrite and sphalerite. Pyrite oxidation contributes very little with respect to base-metals in these natural waters.

Jan 1, 2000

By J. A. Brierley, C. L. Brierley, K. A. Prisbrey, R. W. Bartlett, J. G. Harrington

Bacterial oxidation of gold-encapsulating sulfide minerals in low-grade refractory ores was investigated over a period of one year. Crushed ore samples were held in wet, bacteria-inoculated, aerated columns. Sulfide mineral oxidation data were correlated with subsequent gold cyanide extractabilities. Experimental results for both sulfide conversion and gold extraction were compared with a biooxidation kinetics model that incorporates rock size, mineral grain size, and heterogeneous pyrite reaction kinetics. Using the model, extrapolations were made over three years for biooxidation of ore in large stockpiles. Ferric ion (oxidant) diffusion in the solution-filled pores of the rock matrix does not control the biooxidation kinetics of ore crushed to -25 mm.

Jan 1, 1993

By C. J. Bise, D. A. Poukhovski

Hazard recognition and prevention of accidents are two components of the 30 CFR 48 training requirements, which are mandated for new miners and newly employed experienced miners. These components are also part of the annual refresher training course required of all miners. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine and shall include a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition presents a particular challenge to safety-training specialists, because they are often limited in their ability to adequately gauge the level of awareness of the individual prior to training. Further, they must also assure that the training is relevant and presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard-recognition topics, because it can be used in pretraining and posttraining modes for assessment of training effectiveness, in addition to its use as a presentation tool. This article presents a recent approach, developed at The Pennsylvania State University, that applies the technology for the assessment and instruction of accident prevention through hazard recognition. The application is prepared for surface coal mines.

Jan 1, 1999

By Barton Kelby Cross

In the early 1960's the feasibility of mathematical modeling was demonstrated in Northern Rhodesia and southwestern United States, where techniques were developed to use these models in a new approach to aid engineers in the estimation of ore reserves, mine designs, and financial evaluations. These rudimentary models closely followed the manual methods, producing ore reserves and production schedule estimates that were as accurate as the manual methods, yet were many times faster. Mines evaluated and designed using these new tools gradually came into operation during the 1970's and entered the phase at which production scheduling and ore-grade control became day-to-day problems. Management expected the number of operational engineers to be small because small planning engineering staffs had produced the original designs and operated the smaller high-grade pits. Unfortunately, the tools needed by the mine engineer to perform short-term production scheduling and ore-grade control were labor intensive; they had not yet been generally computerized. Several attempts to use the original or exploration model for these two functions were futile. While an exploration model based on data from exploration work proved sufficiently precise for overall mine design and long-term production scheduling, the model lacked the precision required for short-term scheduling and grade control.

Jan 1, 1979

By Palmer C. Sweet

By-products from mining and processing plants and coal-fired power plants are being utilized more as valuable resources in Virginia. Mining-related by- products are divided into two categories: those generated from mineral extraction and beneficiation, and those generated from mineral processing or from industrial plants. Materials from both categories are produced in Virginia, where by-products have been exploited for various uses in the past and/or present. These materials include coal- combustion products (fly ash and bottom ash), lime-kiln dust, flue-gas-desulfurization residue, rock fines, magnetite, Cold Spring clay (kaolin), Austinville tailings, soapstone rock, and calcium-carbonate paste. Some of these by-products have never been utilized, although several ideas have been investigated over the years.

Jan 1, 1999

By D. A. Day, H. L. Marsh, P. J. Stephens, C. A. Wiggins

Lightweight cellular grout backfill behind pipe-in-tunnel has been gaining increased acceptance in the tunneling industry and has proved to be both practical and economical. Two successfully constructed projects, the Upper Scioto West Interceptor Sewer (USWIS), in Columbus, Ohio and the Benbrook Pipeline Tunnel Project in Fort Worth, Texas will be discussed. The projects represent two different but successful applications of lightweight cellular grout backfill. The USWIS placed the grout behind precast reinforced concrete pipe, in water bearing limestone, and in close proximity to residential water wells. The Benbrook Project placed grout behind 6,096 meters (20,000 feet) of steel pipe from just two locations, eliminating major surface disruption typically associated with the placement of pumped concrete.

Jan 1, 1999

By J. A. Bartnik

In recent years, the need has become more and more accute for a high capacity, high intensity, wet magnetic separator for the concentration of finely ground, paramagnetic minerals. As a result of this increased interest, extensive test work has been conducted at our Central Test Laboratory, and the basic design for such a separator has been established. Three units have been developed to comprise a full line of this equipment: (a) Series 4L (laboratory), Figure I, is manually operated to permit maximum flexibility and precise control of each variable, with a capacity of 4 gallons per minute. (b) Series LOCC, Figure II, functions by automatically controlled feeding and washing cycles, and has a capacity of approximately 1.0 tons per hour. (c) Series 200CF, Figure III, basically consists of an annular pole box, rotating through the high intensity magnetic field. This unit has a capacity of approximately 20 tons per hour.

Jan 1, 1966

By Frank F. Aplan, Edward C. Dowling, Richard R. Klimpel

Several series of time-instantaneous samples were taken on a cell-by-cell basis in the flotation circuits of the Pinto Valley, AZ copper concentrator. These samples were used to calculate mass flow rates throughout the circuit using standard, deterministic metallurgical formulae and also a variety of more statistically oriented techniques. Because of the magnitude of the errors associated with the individual cell samples, the standard metallurgical formulae are not sufficient. Consequently, it is necessary to utilize some type of statistical technique capable of distributing the individual cell sample errors in such a way so as to provide a physically useful mass balance for the entire circuit. This paper explores the use of linear and least squares programming as one technique to providing credible mass balance calculations. For linear programming this was done by distributing the error using two different criteria involving specific linear programming formulations: least absolute sum minimization (which assumes an underlying double exponential distribution error structure) and minimax (which minimizes the maximum absolute deviation and assumes an underlying rectangular distribution error structure). These results were then compared to the more standard formulation of minimization of the sum of least squares which assumes an underlying normal distribution error structure. The least absolute sum approach was particularly attractive due to its simplicity of use and the ease in which repetitive calculations can be done with no user intervention.

Jan 1, 1990

By D. Robert Weir

The pioneers in pressure hydrometallurgy have provided a solid foundation during the past four decades. The pressure techniques are now capable of being used to push back the frontiers in the winning of metals. Pressure hydrometallurgy has been used to meet the objectives of extracting metals; purifying metal solutions, recovering metals; and rendering waste streams acceptable for disposal to waste repositories and the environment. Some examples of each of these functions are briefly reviewed. The applicability of pressure techniques to the recovery of precious metals is discussed.

Jan 1, 1985

By David J. Kruse

The proper modeling of granular flow using discontinuum mechanics has the potential to be one of the most significant scientific advancements in the mining industry today. This paper will examine the status of discrete element technology, specifically focusing on current and future applications. The fundamentals of the Discrete Element Method (DEM) will be briefly introduced, as well as relevant design parameters. Various types of granular flow problems currently being solved using the DEM methodology will be presented. The results and potential benefits of these cases will also be discussed. All simulation results and figures used throughout this paper are from studies and designs preformed by the DEM group at Conveyor Dynamics, Inc. (CDI).

Jan 1, 2000

By [Miroslaw] M. Hajdasinsk

The identification of the real internal rates of return (IRR's) of a project is essential for its economic evaluation. The existing methods for the calculation of IRR's are both cumbersome and unreliable, mainly because of their inability to effectively isolate the real IRR's and incapability of discovering multiple IRR's of even multiplicity. In this paper, a concept of the 'cash flow pattern tree used for isolation of the real IRR's of a project is presented. This concept, combined with the Sturm procedure for counting the real distinct zeros of a polynomial within a specified interval, leads to the development of a method and computer program for isolation and calculation of the real IRR's of a project. The method examines whether or not real IRR's exist, and if they do, isolates them within bounded and narrow intervals in a mathematically founded way. The isolated IRR's, whether simple or multiple, are subsequently calculated either directly or by means of an appropriate approximation procedure. Numerical examples assist the development of the method and the corresponding computer algorithm. Because any Net Present Value treated as a function of interest rate can easily be transformed into a polynomial, the method presented also constitutes a method for finding the real zeros of a polynomial.

Jan 1, 1986