Search Documents

By V. Ciribeni, R. J. Ferretti, C. de Arrieta, E. E. Rossi

The relationship between collector concentration and the solution pH at which flotation occurs is discussed for different minerals. When flotation results are plotted as log of the concentration against pH, the values define areas of total, partial or no flotation. The experiments were performed in three different conditions: a) floating with the same solution used for conditioning; b) floating with water at the same pH as the conditioning solution; and c) floating with water at pH = 7. In each case, the results obtained are quite different. It is suggested that the presence of a second layer of collector reduces flotation over some domains in the graphs. These domains are called depression areas.

Jan 1, 1992

By J. B. Gwiazda

In regard to the paper by J.B. Gwiazda, it makes a highly technical approach to show that the .u factor used by designers of lemniscate-guided roof supports has never really been confirmed as a maximum and assumes that convergence is vertical. Also, the paper does not appear to take into account deflection of structures, which occurs when the lemniscate and base members are fully loaded to their maximum stress level, nor the front to back line of the support in relation to differential roof to floor movements caused by strata movements under pressure. It is not unusual for differential movements to be slightly diagonal to the line of the support, particularly in faulted areas and on gradient faces. The paper also does not take into account consolidation of fines immediately above and below the support. Generally speaking, any differential movement is from face to waste and under these conditions the .u of 0.3, which appears to be an international standard, has worked in practice. However, if the face end of the support is lower than the waste end, then the µ of 0.3 can be considerably increased, giving rise to the damage mentioned in the paper. The ideal design should aim for a slightly forward bias in the lemniscate guide so that the last increment of setting is toward the face, tending to close any fissures that may have developed during the support advance cycle. The support should also be fitted with positive set valves to ensure that a high setting load density is attained to minimize bed separation. As far as powered supports are concerned, convergence is irresistible and all powered supports converge at their rated yield load. A similar principle can be applied to the differential roof to floor movements to drastically reduce the very high forces that would otherwise be applied to the lemniscate structures and pins and that, in turn, are transferred to the base arrangement and floor loading. Any differential movements are usually catered for by the 0.3 µ factor or deflection of structures in the lemniscate guide arrangement and consolidation of the floor. The floor loading, due to differential movement, is in addition to the support convergence load and requires additional bearing area to avoid possible floor penetration. Some seven years ago, Fletcher Sutcliffe Wild Ltd. (FSW) introduced a lemniscate-guided shield support where the lemniscate linkage is connected to the roof bar through two horizontally converging rams to allow differential movement to take place above a given rated figure. This is a known force and can be guarded against, whereas with rigid connections the forces, as yet, are unconfirmed. By careful design, a horizontal force in excess of 6 MN (60 tons) opposes differential movements for a total ram loading of only 2.5 MN (25 tons), or 1.25 MN (12% tons) each. This principle can considerably reduce the length and weight of the support in comparison with a rigid pin-type structure; also, the yield load rating can be increased without affecting the lemniscate forces. The graph shows the tensile and compressive forces in a lemniscate linkage of a support with and without hydrostore. These forces react into both the roof beam and base members and, as can be seen from the support height to linkage load graph, a considerable reduction in these reactions is gained by the use of the FSW patented hydrostore system. Floor loading is considerably reduced under maximum µ conditions, and by allowing the roof bar to move with the strata, some degree of improvement to strata control is achieved in line with the assumptions in the paper. In practice, these movements have only been in the region of a few millimeters, which, in turn, reflects on the improvements to strata control by the addition of positive set valves.

Jan 1, 1987

By Keith G. Wallace, Malcolm J. McPherson

In order to model accurately a mine ventilation system in an existing mine, it is necessary to determine the resistance to airflow in all main airways. This is accomplished by measuring the airflow and pressure differential in each airway. Gauge and tube methods have been used to determine pressure drops in ramps and level airways. However, it has rarely been used in evaluating the frictional pressure drop in shafts. Because shafts commonly have the highest pressure loss in mines, it is critical that the resistance of these airways be determined accurately. This paper describes the theory and practice of using the gauge and tube method for determining the pressure drop in shafts. The pros and cons of using this method are discussed as well as a comparison between the gauge and tube and barometer measurement techniques. Case studies showing the accuracy of shaft gauge and tube measurements are also presented.

Jan 1, 1991

By John O. Marsden

The project development metallurgist is faced with an interesting dilemma: The use of overly conservative metallurgical projections and cost estimates can kill a project that has the potential to provide needed jobs and growth to a company's bottom line. On the other hand if the metallurgist uses a highly aggressive approach by trimming capital and operating cost estimates to the bone and by applying highly optimistic metallurgical projections, there is a risk of creating a project that can never live up to expectations. The metallurgist must walk a tightrope between "sandbagging" and "overoptimism," and this tightrope is fraught with political intrigue and difficulty. This paper takes a some- what lighthearted look at some of the political aspects associated with this issue, and other issues, and offers a few guidelines for walking the "political metallurgical" tightrope.

Jan 1, 2001

By James R. Tompkins

This paper details the successful progression of a promising exploration property into a producing gold mine in only 35 weeks on schedule and on budget. While under construction, an extensive exploration program continued to add to the mine life through the increase in reserves, resulting in a decision to increase the mill capacity from 500 tonnes per day to 1000 tons per day while maintaining the original construction schedule. Details are provided on the unique geology at the Puffy Lake Gold Mine, development from the exploration stage through construction and ultimately to production, with a detailed flow sheet. In addition, of note is the successful change over from contract mining to the hiring of Pioneer personnel who are successfully carrying on both stope mining and development. Operating costs per ounce of gold production are projected at $185 U.S. and alternate methods of mining are currently being examined which could further reduce operating costs.

Jan 1, 1988

By Pradip

The selection, testing, and commercial utilization of flotation reagents is best carried out in stages through microflotation tests on pure minerals and their synthetic mixtures followed by bench-scale batch flotation tests on the ore. A systematic approach to quantitatively evaluate different reagents, in particular, through the analysis of batch flotation data, has been presented in this paper. It is recommended that the reagents are compared both in terms of their performance with respect to the recovery-time as well as the recovery-grade plots. While the former describes the kinetic aspects of reagent interaction, the latter is a measure of its selectivity for a particular separation problem.

Jan 1, 1987

By Katsunori Okaya, Toshio Inoue

Application of the discrete element method incorporating the simple kinetic model of the ball-to-ball and ball-to-wall interactions enables us to visualize the details of the grinding actions prevailing in the ball mills. We have developed a computer program to represent a generic mill model with which we can simulate tumbling mills, vibration mills, centrifugal mills and planetary mills. While the program can be used for various purposes including design of new equipment, one obvious application of it is the analysis of the conventional tumbling ball mills for better understanding and improvement. The purpose of this paper is to present a model and to observe its behavior in particular attention to the spatial distribution of the energy dissipation as well as the energy spectrum and their dependence on the major parameters such as mill speed, ball filling, liner configuration, slurry viscosity and the hardness of the ore.

Jan 1, 1995

By P. Somasundaran, C. C. Harris

The power consumption of stirred-media mills was studied using an approach developed from work on stirred reactors. Evaluated were the relationships of factors such as stirring speed and impeller and tank dimensions on the torque required to rotate disc and pin impellers immersed in dense particulate media. Data collected under carious experimental conditions were analyzed. The results were summarized and presented in the form of characteristic plots, general equations and dimensionless group correlations involving power and modified Reynolds numbers. Special attention was directed towards the rheological properties of the media, which was considered a non-Newtonian liquid, and hence the equation of power-law liquids was employed. A procedure for estimating the parameters of effective viscosity and scale-up guidelines (with respect to power consumption) are proposed.

Jan 1, 1996

By M. Jaramillo

The expanded west pit of the 15 Mta (13.6 stpy) El Cerrejon mine will eventually reach a maximum depth of 270 m (890 ft). Slope-stability evaluations indicated that this depth, combined with structural complexities, would create a serious risk of footwall instability. Stabilization calls for anchoring the footwall by the installation of 9- to 33-m- (30- to 108 ft-) long multistrand steel cable bolts. For each of the 15-m- (50-ft-) high mining benches, a row of bolts is installed with variable horizontal spacing, depending on the dip magnitude. Cable bolting is now standard operating practice, and an estimated 11,800 bolts will be installed during the life of the mine. Results to date have been satisfactory in terms of the stability condition of the bolted slopes.

Jan 1, 1997

Large variations of coal seam thickness and roof conditions are associated with the occurrence of mine floor undulation at Shoal Creek Mine, operated by Drummond Company, Inc.. Ground control problems, such as roof falls and face failures along with extremely high shield pressure and rapid face convergence, are often reported at the longwall face when these undulations exist. This greatly increases equipment downtime and causes production delays. As a result. a comprehensive study of mine geology including roof conditions and longwall performance were conducted in the mine. With the help of continuous full-face shield pressure monitoring using the Longwall Strata Control and Maintenance System (LoSCoMS), a large data base of shield pressure with various roof conditions has been established. This enables the mine operators to accurately evaluate the roof behavior and shield performance and to take the appropriate operational steps at the face to reduce the number of downtime and face failures. This paper summarizes all works and findings from the study including detailed roof geology and its effect on longwall performance.

Jan 1, 1998

By D. Tao, B. K. Parekh

Fine coal particles are difficult to separate effectively from liquids or other solids. Ultrasonic energy may be used to enhance the efficiency of the conventional fine-particle separation processes widely used in the coal and mineral industries. Flotation, settling and dewatering tests were conducted using several fine coal samples to study the effects of ultrasonic treatment on these processes. Process variables such as particle size, ultrasonic treatment time and solids concentration were investigated for their impacts on ultrasonic treatment effectiveness. The results obtained from this study showed that ultrasonic treatment is an effective approach for enhancing solid/solid separation in flotation and solid/liquid separation in sedimentation and dewatering of fine coal. SEM microphotographs demonstrate that ultrasonics cleaned particle surfaces, which is, in part, responsible for the observed improvement in fine coal separation processes.

Jan 1, 2000

By P. E. Nielsen, T. L. Loga, B. B. Mauko

A numerical model is presented which simulates the dynamic fracturing process for a circular geometry fracture in a uniform stress medium. The dependence of crack aperture and net pressure in the crack upon various dominant parameters of the fracturing process is discussed. An analysis of a 75% nitrogen foam fracture in a coal seam at 5600 feet (1707 m) is also presented. The analysis is based upon the discussed parametric trends, the job records of treatment parameters, and a Nolte plot of net downhole pressure. It is interpreted that fracturing with water, in pre-foam fracture pump tests, resulted in significant fracture height growth. However, the subsequent foam fracture had reduced height growth due to the high effective viscosity of the foam and due to the higher magnitudes of elastic modulus and stress in the bounding rock strata with respect to the coal.

Jan 1, 1986

By Jukka Pukkila, Pekka Särkkä

Intensive co-operation between mining industry and mining machine manufacturers during an eight year program Intelligent Mine™ led to a new concept for applying automation technology in mining to improve the productivity and safety of mines. 'The results of the program are now implemented in several mines in Finland and with similar ideas as well elsewhere in the world. The degree of optimal automation of an intelligent mine depends on several technical and economical factors. The basic precondition for the approach is a clear improvement in total economy of the mine.

Jan 1, 2002

By Gregory W. Gustina, Terry P. Boyle

Analysis of the structure of the benthic macroinvertebrate community, consisting of the number of taxa and the relative distribution of total numbers, is a routine method of assessing the ecological quality of streams. Various multivariate statistical techniques, which assess the structural variability of the benthic macroinvertebrate community and the relationship of that variability with natural and anthropogenic environmental variables, have utility in separation of the various physical and chemical factors associated with impact. Multivariate methodology, while computationally complex is statistically rigorous and better integrates physical, chemical, and biological data for more synthetic interpretation. Using the multivariate analysis technique, canonical correspondence analysis, we have analyzed a number of sites in the upper Boulder River Basin, Montana to determine which are the important environmental variables associated with variation in community structure. The results of this analysis an integrated with more traditional analysis of community structure and incorporated in a risk analysis for the mediation of abandoned mines and mill sites within the watershed.

Jan 1, 2000

By E. K. H. Goh

A reliability-based engineering design approach for the effective design of reshaped spoil dumps was developed with the aim of obtaining structurally reliable spoil dumps at optimum reshaping costs. The aim was also to satisfy environmental erosion standards and community expectations. This approach encompasses the linking up of three major components: erosion appraisal of spoil dump designs, reliability-based engineering design of spoil dumps and costing of spoil dump reshaping practices. This paper addresses the application of the reliability-based engineering- design approach to the assessment of spoil dump designs for erosion control. Included are various types of erosion prediction models and reliability-based engineering-design analytical techniques. Also included is a case study that demonstrates the application of this approach.

Jan 1, 2000

By B. Elevli, M. D. G. Salamon

Production scheduling of an open-pit mine is one of the most important steps in open-pit mining. The mine's production schedule defines the distribution of cash flows and, as a result, directly influences the net present value (NPV) and overall economic feasibility of a project. The need to plan and operate a mine with an optimum production schedule has been obvious for some time, but the methods used to obtain such a schedule have not been so obvious. The current practice is to do a trial and error analysis by hand. In an attempt to improve the way production scheduling is currently done, a new computer based production scheduling algorithm was developed. This paper describes the fundamentals of this newly developed heuristic scheduling algorithm and its application to a gold deposit. The results of this case study show that the schedules, based on the new method, provide improved cash flows compared to production schedules done manually.

Jan 1, 1992

By Cynthia S. A. Wallace, Joseph E. Crawford

The Culberson ore body is a bioepigenetic sulfur deposit located in the Delaware basin. Sulfur occurs in the Upper Permian Castile, Salado and Rustler Formations. Most of the ore body forms a subhorizontal layer within the Salado Formation. Abundant cave fill deposits of Rustler and younger lithologies occur within the Salado Formation and predate mineralization. The cave fill deposits provided porosity zones within the otherwise impermeable sulfate host rock and controlled sites of mineralization. A northeast trending fracture zone near the west edge of the ore body localized some deep mineralization and may have allowed migration of hydrocarbons from depth.

Jan 1, 1992

By Boris M. Vorobjev

The paper in question discusses a wide range of topics on the coal mining environment in general and on computerized coal mine environment systems in particular. The emphasis is being made on methodological aspects of coal mine environment with reference to computerized monitoring systems Classification of computerized coal mine environment monitoring system is suggested by the author with specific reference to coal mining operations. Coal quality control system at all levels (coal face to regional levels) is also discussed briefly hereunder, since coal quality is one of the major factor for environmental management. An integrated coal mining economic and environmental management super-system is presented in this paper Review Of the UN/DTCD, UNDP European Regional project "Computerized Coal Mining Systems" is presented here. Conceptualization of a new European Regional project on Coal Mining Environment and Economic Management is also a topic discussed in the paper.

Jan 1, 1992

By Steven A. Whittle, Robert E. Cook

Years ago, personal computers (PC) were pricey devices destined for who knows where in the process industry. Now their use runs the gamut from low end data acquisition systems to high performance windows into the process area. Their applications range from CAD, CAM, CIM, and CAE to factory floor scheduling, process planning QC, facility management, cell control, and publishing. This discussion traces the evolution of a zinc plant's control automation program beginning with a PC as an operator interface and migrating to higher level work stations. Included in this paper will be a discussion of an Open Industrial System and the role PCs have played in this facility.

Jan 1, 1993

By Arpad E. Torma

The introduction of biotechnological principles in hydrometallurgy has created new opportunities and challenges for the industry of mineral processing. During the 1950's and 608s, the mining wastes and unused complex mineral resources have been successfully treated in bacterial assisted heap and dump leaching processes, especially for the production of copper and uranium. The economic viability of bio- leaching technology lead to its world-wide acceptance by the mining industries. During the 1970's this technology grew into a more structured discipline which is called "biohydrometallurgy". Currently, bioleaching techniques are ready to be used, in addition to copper and uranium, for the extraction of cobalt, nickel, zinc, gold and silver from diverse mineral resources and for the desulfurization of certain coals. However, in a foreseeable future the biohydrometallurgical processes may be applied also for the treatment of high- grade ores and mineral concentrates using native and/or genetically engineered microorganisms.

Jan 1, 1989