Search Documents

By Pierre Mousset-Jones, Felipe Calizaya, Malcolm J. McPherson

The algorithm presented in this study determines the combination of fans that provide all working districts of a mine with predefined airflows at the minimum operating cost. It is based on an existing ventilation simulator, VNETPC, and a set of linear equations associating fan pressures and the added resistance of regulators. Two assumptions are undertaken: (1) fan locations are predetermined and (2) the number of working districts is equal to or greater than the number of fans. By means of this algorithm, the optimal solution to an n fan ventilation system may be found after n + 1 simulation runs.

Jan 1, 1987

By H. Zhu, A. G. Journel

Qualitative and interpretive information as obtained from geological and/or geophysical studies, in addition to precise measurement, is incorporated into the estimation process through an indicator variable. The indicator conditioned estimator is formulated as a cokriging, and its expression is data value dependent as opposed to that of the traditional kriging estimators. The solution of the dual cokriging system provides simultaneously an estimate of the unknown and an estimate of the conditional probability that the unknown belongs to a specific population or class. Being an unbiased and minimum-error-variance estimator by construction, the indicator conditioned estimator is better in the least square sense than the ordinary kriging estimator because it uses additional information carried by the indicator data. A case study using a large reference database is presented; the indicator conditioned estimates have a smaller conditional bias and a smaller error variance than the ordinary kriging estimates. The results also showed that the indicator conditioned estimator is more efficient for selection in mining.

Jan 1, 1990

By W. R. Dearman, N. Turk

A seismic fissuration index (K) is defined as the ratio of the difference in the P and S wave velocities obtained when a dry rock specimen is tested both under a load equal to half the uniaxial compressive strength of the rock (Vo) and without an applied load (Vd) to the velocity obtained without an applied load (Vd), as K = (Vo - Vd)/Vd. A similar seismic fissuration index is also proposed for classifying the dry rock mass in terms of field seismic velocities. The field equation is extended by including the intact rock seismic velocities. K is found to be related to the porosity of rocks. The proposed equation can equally be used for characterizing saturated rocks, using S-wave velocities. However, the time average equation should be used for characterizing saturated rocks, using P-wave velocities, even though this equation gives upperbound estimates of the rock material and fracture porosities.

Jan 1, 1986

By Chi M. Phan, Anh V. Nguyen, Geoffrey M. Evans, Graeme J. Jameson

Surfactants are used to control the interfacial properties of the gas-liquid and liquid-solid inter- faces inflotation. This paper investigates the dynamic adsorption of surfactants at the gas-liquid intelface. The dynamic adsorption process was modeled by considering the surfactant mass transfer to the gas-liquid interface by dimion and the Langmuir and Frumkin adsorption isotherms. The numerical computation was applied to solve the non-linear governing equations. The dynamic adsorption was measured in tenns of the dynamic surface tension using the pen- dant drop method. The theoretical modek were compared against the experimental data obtained with non-ionic (Dowfroth 250) and ionic (sodium dodecylbenzene sulfate, SDBS) surfactants. The theoretical results agreed well with the erperimental data for SDBS, but not for Dowfrother 250, especially for the initial stage. Reasons for the variation in results are given in the paper.

Jan 1, 2005

By R. D. Ellison, D. K. Shukla, D. E. Stephenson

Seals for man-made penetrations into or nearby nuclear waste repositories require several unique capabilities not common to seals for conventional underground activities. Design criteria include long functional use, extremely low permeabilities of the seal zone (including adjacent disturbed rock), and the potential for retarding radionuclide travel. This paper summarizes comprehensive seal programs being conducted by D'Appolonia for the Office of Nuclear Waste Isolation (ONWI) at Battelle, Columbus. The program schedule requires the first detailed conceptual design for a bedded salt site to be completed in 1982. Conceptual designs for other host media will follow as site exploration data becomes available. The design program is supported by a variety of office, laboratory, and field activities being conducted by ONWI subcontractors. An example is provided to illustrate the variety of efforts directed toward determining the extent of disturbance adjacent to penetrations as a result of in-situ and excavation methods. Also, the current "working design" for the shaft and tunnel seal system at the candidate Los Medanos thick salt site in southeastern New Mexico is presented.

Jan 1, 1981

By D. C. Seidel, W. K. Tolley

Supercritical water alters the structure of common sulfide minerals by partially removing sulfur from the mineral structure. This discovery has been applied to the treatment of pyritic gold ores to improve precious metal recovery without generating or utilizing environmentally sensitive products such as S02, chlorine, or cyanide. Pretreating pyrite concentrates in supercritical water under mildly oxidizing conditions provided by certain metal oxides or oxygen improved gold leaching using thiourea. The pretreatment differs from chlorination or roast pretreatments in that elemental sulfur rather than sulfuric acid is the major product. A pyritic ore containing 58 g/mt Au was pretreated with oxygenated supercritical water at 24 MPa and 400°C, then leached with 20 g/L thiourea. With pretreatment, gold recovery was 90%; by contrast, gold recovery was below 10% without pretreatment.

Jan 1, 1990

By R. E. Johnson, W. Kat, B. R. Palmer, van Sandwijk A., G. Van Weert, S. Honingh

In-plant recycling of dust from iron making BF's creates undesirable circulating loads of volatile trace elements such as zinc and lead. Disposal of such dusts creates environmental problems, hence a separate treatment is indicated. Since the bulk of the zinc and lead compounds occurs in the fine dust fraction; hydrocycloning the slurry from the BF gas cleaning operation results in upgrading the material for treatment. A process has been proposed, whereby the zinc and lead are solubilized from the fine fraction with spent hydrochloric acid from steel pickling. The stoichiometry of this autoclave oxidation process is adjusted to simultaneously precipitate, by oxyhydrolysis, most of the iron for recycling to the BF's. Lead and zinc are successively recovered from the filtrate as low chloride precipitates. This paper describes additional testwork, leading to the design of a pilot plant which was planned to begin operation in 1992.

Jan 1, 1993

By K. A. Natarajan, M. K. Yelloji Rao

The electrochemistry of sphalerite and chalcopyrite was investigated under both open-circuit and applied potential conditions. Emphasis was placed on the selective dissolution of sphalerite from a mixture of sphalerite-chalcopyrite flotation concentrates as a function of applied potential, acid concentration, pulp density, and time. Morphological studies using a scanning electron microscope (SEM) were also carried out with chemically leached, galvanically leached, and unleached surfaces of sphalerite and chalcopyrite. Selective dissoulution of sphalerite could be achieved if the mixed chalcopyrite-sphalerite concentrate slurry was maintained at a negative applied potential of -0.4V (SCE). Probable mechanisms involved in the selective dissolution of zinc are disscussed.

Jan 1, 1990

By R. R. Jozefowicz, T. X. Ren, J. S. Edwards

The control of methane emission into underground mine workings is important both for the safety and productivity of the mine. As deeper and gasser coal seams are mined, ventilation methods involving increasing air pressures and quantities across mine workings may not be able to cope consistently with methane emission rates during the production cycle. An accurate prediction of methane emission into mine workings is of great significance in the design of ventilation systems and additional methane control methods if required. Research has been conducted to develop a numerical method for simulating methane flow through strata in which permeability is strongly influenced by mining-induced stress. To achieve this objective, both numerical modelling using Computational Fluid Dynamics (CFD) and laboratory tests on rock samples and granular materials under triaxial stress condition were carried out. Correlation has been established between stress and permeability characteristics of rock-measure rocks and laboratory results are being incorporated into the CFD models. This paper introduces the use of CFD techniques to model methane flow through permeable strata around longwall coal faces currently undertaken at the University of Nottingham.

Jan 1, 1997

By Robert A. Jankowski, Jonathan Kelly, Edward F. Divers

Results for the first underground test of the ventilated drum in a U.S. coal mine are presented. Tests were conducted by the Bureau of Mines through a contract research program with Foster-Miller, Inc., to evaluate dust control effectiveness in a western mine and for gas control in a full scale laboratory facility. The ventilated drum is designed to reduce the amount of dust from cutting by drawing dust-laden air from the cutting zone through twelve water- powered "dust capture" tubes built into the shell of the shearer drum. High pressure water up to 1 12.48 kg per cm2 (1,600 psig), released from sprays, induces maximum airflow of 1.89 m3/sec (4,000 cfm) from the face side of the drum and provides cleaning for respirable dust and improved methane dispersion. At the gob side of the drum a deflector plate, attached to the cowl arm, turns the water spray and a proportion of the cleaned air back into the cutting zone. More than 50 ventilated drums have been installed to date in England, and their tests carried out on fixed height and single-ended ranging drum shearers have shown reductions in respirable dust of 60-80 pct, as compared with conventional wet cutting. The U.S. test on a double drum shearer showed slightly lower reduction.

Jan 1, 1987

By Robert J. Timko, R. Lincoln Derick

This report presents a Bureau of Mines evaluation which examined the extent of gas leakage from sealed areas in underground coal mines and measured the effectiveness of commonly used structures for controlling the quantity of gas exchange from these areas. Evaluations were performed on five abandoned areas in two operating underground mines within the same coal seam. Methane and oxygen levels inby the seals were monitored to determine if the gas leakage was unidirectional or bidirectional. Results from this and prior work dealing with minimizing gas leakage were then applied to a newly abandoned area. Also discussed are bulkhead site preparation, construction plans, techniques for monitoring the status of the atmosphere within the sealed volume, and a modified European method for controlling gas migration from the sealed volume to the active mine.

Jan 1, 1991

By David G. Laughton, Richard Poulin, Michael R. Samis

Real options (RO) valuation is an alternative net present value (NPV) framework that is able to incorporate both management flexibility and dynamic project risks. In this paper, management is considering the development of a satellite low-grade zone while operations in a developed high-grade zone continue. If the low-grade zone is developed prior to high-grade zone exhaustion, mine capacity must be expanded before additional production from the low-grade zone can be processed. This expansion can be avoided only if low-grade zone development is delayed until the high-grade zone is exhausted. The RO model presented here allows the development and capacity expansion decisions to be reconsidered on a discrete half-year basis. It delineates price regions, for given levels of high-grade zone reserves, in which it is optimal to develop the low-grade zone, defer low-grade zone development and abandon the mine irrevocably.

Jan 1, 2002

By W. F. Kane

Underground geologic mapping is an extremely important aspect of any on- going ground control plan. However, the actual use of data derived from such a program is difficult and often leads to subjective analysis. In this regard, computer software has been developed that utilizes a statistical determination of unstable ground conditions based on geomechanical and operational data and collected by mine personnel on a mine-wide, or regional basis. Categorical variables, such as faulting or joint frequency, are selected from local experience to form the framework of a representative data base. Statistical comparisons between the selected variables and a particular ground control problem are conducted and correlations subsequently made. The probability of encountering unstable conditions in virgin areas is assessed as information from these regions is gathered. This data can be derived from surface mapping, cores, and/or geophysical logs. As mining progresses, new data is merged with the existing data base to form a more comprehensive and extensive unit. The advantages of this approach and the acquisition and maintainence of a large data base include the more accurate representation of existing mining conditions, increased confidence in analyzing future problem areas, and elimination of the difficulties which arise when using ground control theories derived for other, often very different, locales.

Jan 1, 1986

By J. A. Herbst, Y. C. Lo

An attempt has been made to parameterize the population balance model for a ball mill based on measurements of the elementary breakage process obtained using an ultrafast load cell device. Detailed insight obtained concerning the fragmentation of particle assemblies with the ultrafast load cell leads to a better understanding of ball mill grinding. The ball mill breakage function and specific selection function are derived from an average single event representing the multiple breakage events which occur in ball mill grinding. Since both the breakage function and the specific selection function depend on the loading mode in the mill, predictions of breakage mechanisms in ball mills are possible by using data obtained in various elementary loading modes. The application of this model to the description of batch ball milling behavior has resulted in reasonably accurate predictions of product size distributions for various energy inputs.

Jan 1, 1992

By Brian Kenner, Peter Swanson, Todd Krahenbuhl

NIOSH has developed an automated PC-based seismic event (induced earthquake) monitoring, system for use in mine ground control studies. The distribution and coordination of data acquisition and processing functions across a local area network is a central feature of the system. Mine-wide installations utilize multiple, autonomous seismic networks located both underground and on the surface. Seismic event locations, magnitude estimates, and other processed data are distributed for display and analysis on network nodes both underground and in the offices of mine engineers and managers. This paper describes the system's design philosophy, hardware and software components, examples of installations, and a few observational results.

Jan 1, 2002

By B. Ainsworth

The 1972 discovery of the Howards Pass lead-zinc deposit was the product of systematic regional geochemical surveys used to evaluate conceptual geological models for the metal-rich black shales of the Selwyn Basin. Motivation of personnel involved in all aspects of work was as critical a factor to the success as the existing corporate attitudes and infrastructure. Exploration programs were flexible but maintained a focus only on targets of sufficient economic potential to support operations in remote locations. Direct costs for the programs that lead to the discovery were in the order of $500,000 (Canadian 1972). Geological reserves today stand at over 500 Mt (511 million st) of 7% combined lead-zinc, containing a higher grade zone of nearly 10 Mt (11 million st) of 16% combined lead-zinc.

Jan 1, 1991

By P. H. Williams

Experiences gained using computers in the mining and geological environment have shown that it is quite rare for a system or the data it stores to be truly stand alone. Just as the mining enterprise aims to have a smooth integration of operations from exploration through mining and extraction to sales, so it should develop all its information systems within an overall framework or architecture which covers the applications and data as well as the computer hardware and communications. This paper discusses methods of achieving such an architecture, and describes some of the benefits it can have on the development and implementation of information systems. The key aspects are the identification of the business functions and the data that they use, and ensuring that the IS plan supports the overall objectives of the enterprise. Hardware and communications policies should be based on the plans for the applications and data, rather than the reverse.

Jan 1, 1986

By R. Debkowski

Mining methods used to protect the workings in underground salt mines against the destructive activity of natural factors are presented in this paper. Major hazards and methods of elimination of their impact on the stability of workings, were determined. Old and modern technical means and technologies used for protection and preservation of the selected most interesting sites were characterized. The results of surveys and studies allowed proposing the change of mine structure i.e. dividing it into monumental and not-monumental part, which should improve execution of necessary protective works.

Jan 1, 2006

By Takeshi Tanaka, Shinya Ono, Tsuyoshi Kato, Masaji Kato, Yuusaku Tominaga

The knowledge of the macroscopic characteristics of a ventilation network is of fundamental importance for taking counter- measures to increase air quantity in-specified branches, such as those corresponding to working faces at advancing entries or longwall panels. Because the ventilation characteristics are inherent properties of each mine, it takes a long time for an engineer to accumulate experience on how a specific regulator may affect the air quantity in a specific branch of a mine with a complicated ventilation system. A computer-simulation training system, based on the macroscopic ventilation characteristics, is presented in this paper. When a trainee selects a specific condition from five regulator option (closed, almost closed, slightly open, half open, open), the change in air quantity for a network branch is indicated by the color allocated to the ratio of the new air quantity to the old or planned air volume. After the ventilation simulation, the colors in the specified branches are defined by using the fuzzy set theory. The trainee continues practicing the selection of closed/open conditions for different regulators until each of the specified branches is displayed in good state of airflow. The ventilation net- work of the Horonai coal mine is used as an example of the training system to control air quantities in six working faces with 33 regulators.

Jan 1, 1996

By R. L. Grayson, S. Yuan

A stochastic model for evaluating the impact of the reliability and maintainability of shovels and trucks on the operational effectiveness of shovel-truck mining systems is presented. In the model, the Markov modeling technique is used to analyze the operating status of a shovel-truck mining system. Then, simulation is used to study the productivity of a shovel-truck system in a particular state. Finally, the relationship between the effectiveness of a shovel-truck system in terms of productivity and the reliability and maintainability of equipment is established. This relationship may be very useful to mine managers in making decisions in surface mining (e.g., regarding production process control, equipment replacement, and maintenance planning). A quantitative study is given to demonstrate how the reliability and maintainability of equipment affect the system effectiveness and how to pinpoint the parameter that has the most significant effect on the system effectiveness. The quantitative study indicated that in order to improve the system effectiveness significantly, the reliability and maintainability of the equipment need to be improved simultaneously.

Jan 1, 1995