Search Documents

By J. Partyka

Adequate ventilation is a main concern if Lockerby Mine near Sudbury is to be expended. This study investigate a two-fold problem: (1) the new pressure and volume requirements of the main fans due to the theoretical. deepening of the mine, and (2) the effect of the natural ventilation pressure on the main fans. Field data was analyzed with the aid of a newly developed network simulation program, VNETPC Version 3. 0. The density change throughout the mine is accounted for by performing all computations at reference density. Results of the investigation indicate that the existing fan system must be supported by three to five additional underground fans as well, the density effect is significant. If neglected, it will greatly alter the simulation results

Jan 1, 1991

By C. DeRossett, K. F. Unrug

Sedimentary rock fractures commonly occur in the vicinity of outcrops. Mine highwalls and highway cuts provide excellent views of these near-surface joint systems. This paper explains the origin, characterization, distribution and extent of the these joint systems with reference to the lithologic composition of the rocks. The practical implications of these joint systems on the operation of a mine are described. Included are discussions of the discontinuous deformation that results from surface subsidence, the stability of mine portals and near-outcrop underground operations, and the stability of highwalls when using highwall miners and strip operations. Some design procedures are recommended to minimize the problems encountered within mining areas having intense joint systems.

Jan 1, 1996

By R. W. Hughes, R. Koopmans

This paper investigates the effect of varying stress levels on the determination of deformation moduli and examines the sensitivity of the borehole dilatometer in measuring rock mass scale features and its ability to represent rock mass characteristics. Cubical blocks of sandstone, limestone and granite were tested in the laboratory under triaxial stress conditions. Field programs were conducted in both granite and sandstone rock masses surrounding underground openings. The dilatometer's zone of influence was determined by conducting tests within an instrumented concrete cylinder and by performing a finite element analysis. Laboratory and field results suggest that the deformation modulus of a rock mass can be substantially affected by the stress field and that the borehole dilatometer is sensitive enough to profile deformation moduli as dictated by the in situ rock mass characteristics.

Jan 1, 1986

By M. A. Cocquerel

INTRODUCTION Davy McKee have developed and patented a combined mixer settler (CMS) which has undergone extensive trials and has now been installed in two commercial uranium plants in South Africa. Substantial capital and operating cost savings can be realized over conventional mixer settler in uranium extraction, especially from dilute feedstocks containing approximately 200 ppm U308. Pilot plant work has also been undertaken on other metal extraction systems and the results are very encouraging in most areas of interest. CONVENTIONAL MIXER SETTLERS The conventional plant in use at many uranium recovery facilities consists typically of a mixer box in which the aqueous and organic phases are contacted and a settler in which the two phases separate. The mixer box must allow sufficient residence time for the mass transfer kinetics to be satisfied for the particular species involved. The settlers are usually rectangular and take the form of shallow tanks of large cross sectional area.

Jan 1, 1984

By Lawrence J. Connelly

During the last decade, use of freeze conditioning agents (FCA) to ease unloading and handling of both run-of-mine and washed coal during periods of cold weather has become an accepted practice by the coal industry. This paper reviews some of the mechanical means of easing the handling of coal during periods of cold weather, as well as their use in conjunction with FCA's. Factors required to promote a successful cold weather handling program are also covered. Mechanisms by which FCA's function and the influence of various substrate characteristics on the ultimate response to freeze conditioning agent performance are discussed. A modified approach to freeze conditioning is presented.

Jan 1, 1986

By M. H. Foroughi

In this paper, the compressive strengths, failure modes and acoustic emission behaviors of cubic coal specimens containing bedding planes at various inclinations are considered. Test results showed that the compressive strengths and the modes of failure of coal specimens depend on the inclination of the bedding planes. From the acoustic emission (AE) measurements, the count rate detected through a low-pass window (AE (L)) was compared with that through a high-pass window (AE (H)) in each test. The results of accumulated AE history were compared with AE signatures of others. It is shown that the AE signature of coal depends on the inclination of the bedding planes, and the AE signatures can be classified into three groups. Each group corresponds to a particular mode of failure, namely, slip on the bedding planes, fracture across the bedding planes and fracture extension through the bedding planes. The parameter r, defined as the ratio of AE (L)/ [AE (L) + AE (H)], is plotted against the stress for each test. Test results showed that r also depends upon the inclination of the bedding planes.

Jan 1, 1999

By Deli Hu, Xiangze Shu, Cai Wang, Hongfu Liu

To detect the place and range of fire is one of the key technologies in the extinction of coal mine underground fire. A fire-prevention and extinction research team of Shanxi Mining College have successfully carried out a program detecting the place of fire with radon. In the past four years the authers have done the detecting work in several mines in Shanxi Province, such as Gujao, Xuangang Louan and Ningwu. The place and scope and the trend of underground fire of coal mine can be now exactly estimated. The data and information from detecting provide a reliable basis for drawing up the scheme to extinguish underground fire and extract mineral coal securely. The principle and method of fire detecting based on radon on surface, the data processing and analysis are discussed in this paper.

Jan 1, 1991

By Y. C. Kim, M. Preston, F. Martino

Because of the high cost of obtaining coal washability samples, it has been difficult in the past to obtain washability variograms. As a result, it could not be determined if the geostatistical prediction tool known as kriging can be applied to predict in situ coal washability characteristics. This paper presents the obtained variogram models for the Upper Freeport coal seam in western Pennsylvania. Variogram model parameters are presented for a total of 27 models. They are for four different variables: float- weight, ash, sulfur, and Btu, at seven different specific gravities: 1.275, 1.300, 1.325, 1.400, 1.600, 1.800, and 1.80,Sink. Based on the obtained variogram results, it can be con¬cluded that all attributes of coal washability show definite spatial correlation structures, and, consequently, geostatistics can be used to predict the in situ coal washability characteristics.

Jan 1, 1990

By James M. Prudden, Jon C. Sprague

Valdez Creek Mining Co. properties consist of multiple intersecting paleo-placer channels containing appreciable quantities of coarse gold. Reverse circulation drilling, combined with geophysics, is used for both exploration and development reserve determination. Classical drill-blast-load-haul open pit mining techniques used for the 22,000 cubic yard per day production schedule required modification to compensate for arctic winter operating conditions. High wall stability problems within the glacial sediment overburden necessitated developing multiple dewatering methods and variable pit slope designs to eliminate unstable pit wall conditions. Processing mine run fluvial gravels utilized a classical winter protected screening plant-sluice box recovery system enjoying high metallurgical recoveries and zero discharge tailings disposal.

Jan 1, 1987

By Nancy C. Shaver, Alan Tapp

Leach pads of 272,000 tonnes (300,000 st) and 910,000 tonnes (1,000,000 st) with associated operating ponds have recently been constructed on sidehill locations with up to 20 percent slopes. The larger pad was designed in anticipation of ore heights up to 30 meters (100 feet). This paper describes site investigations and civil engineering design as well as construction experience associated with development of these pads. The leach pads were underlain by a double liner system consisting of 2 mm (80- mil) HDPE over compacted fine-grained tailings, with an intermediate leak detection layer. Both sand and geotextile drainage layers were used. Pad slopes were limited by the factor of safety against sliding on the HDPE liner. The sites for the facilities had been substantially disturbed by prior mining and construction activities. Natural conditions included peat layers and locally swampy ground. Site preparation included french drains to lower the water table and stripping of unsuitable subgrade materials.

Jan 1, 1987

By Sukumar Bandopadhyay

A present dominant problem is that of high downtime of the longwall shearer used in the coal production process. The means by which this problem can be overcome are many, but one of, the most important ones is that the-use of an expert system can reduce diagnostic and repair time. In this paper, a fault-diagnostic expert system model is presented. Specifically, the diagnostic architecture of the longwall shearer expert system and its use for diagnostic reasoning are discussed.

Jan 1, 1989

By Emil O. Frind, David W. Blowes, K. Ulrich Mayer

The multicomponent reactive transport model MIN3P can be used to simulate the evolution of pore water, pore gas, and the mineralogical composition in mine waste environments. The model is formulated for variably-saturated conditions, considers transport of dissolved and gaseous species, and describes geochemical reactions based on a partial equilibrium formulation. Reaction processes included are complexation, oxidation-reduction, ion-exchange, mineral dissolution-precipitation and gas exsolution- dissolution reactions. An example application, describing the generation of acid mine drainage and subsequent reactive transport for a ID-vertical profile in a tailings impoundment near Elliot Lake, Ontario, is provided.

Jan 1, 2000

By R. Mira, S. Rosa, P. Souza

This paper shows the historical data, local geology and mineralization, the mining methods applied, current production,, the planning staff, the resources of hardware and software available and the computer methods used. The activities are described starting with the driving of ramps/research levels, their dimensional parameters and positioning, driving of production sublevels with the same parameters plus those concerned with the stability of the rock mass during the development and the mining itself. Then, the detailing of the ore body is described together with the stopes planning, the openings stability analysis, and the drilling patterns and explosive types are discussed.

Jan 1, 1998

By L. P. Meade

The need to feed an established talc mill from a crude ore source located closer to the mill prompted the 1986 drilling of a previously mapped, talc-carbonate deposit. This talc-bearing rock had never been considered a potential source of crude talc ore because of the high carbonate content and other deleterious minerals observed in outcrops. Selective mining, in-pit grade control and creative processing have allowed this deposit to be developed into an ore body. By definition, an ore body has to be a source of positive cash flow. With industrial minerals, this is determined as much by market acceptance as by ore tenor.

Jan 1, 1994

By Myles P. Reilly, Randall A. Snowdon, John Temporal, O&apos

The paper describes studies made at the Transport and Road Research Laboratory, UK, of the mechanical cutting characteristics using disc cutters, of rocks with compressive strengths up to 340 MPa. These studies have been performed in both the single pass mode, where interactive breakout occurs between adjacent grooves on every pass of the tool, and the multiple pass mode, where several passes may be required to cause breakout. In addition, experiments to determine the effect on cutting performance of the hydraulic stiffness of tunnelling machines are described. The results of these tests are analysed and discussed in the context of the design of full-face tunnelling machines.

Jan 1, 1983

By D. Greene

The close integration of mine planning and mine operation continues to be the goal of mine operators. Depending upon the complexity, size and sophistication of the mine, limited success has been achieved in this area. Despite tremendous strides in the development of computer-aided mine planning, digital plans must usually be converted to error-prone paper maps and physical ground surveys for actual excavation and reclamation. However, advances in global positioning systems (GPSs), operator displays and mobile computers now enable equipment operators to work directly from on-board digital plans. A computer-aided earthmoving system (CAES) offers reduced survey costs, faster field transition time and improved excavation accuracy, coupled with faster, more informed decision making regarding key mining operations.

Jan 1, 2000

By Yongping Hu, Dianchen Cai, Congya Zhang

China is a rich in stromite mineral resource. Unfortunately, the resource is very difficult to separate by using conventional flotation method because stromite and gangue minerals are very fine disseminated, the average size of them is about 10 µm or below, and the content of clay minerals such as illite is 19% or even more. In this paper, the aggregation floatation behavior of ultrafine (-10 µm) stromite, illite, ablbite and quartz using anion collector were studied. The result show that, Oxidized paraffin (O.P) is a good collector and has better selectivity for stromite particles flotation. The salted sodium silicate depressed illite gangues minerals effectively. The separation of mineral mixtures was carried on successfully at one stage flotation by the technique. The mechanism of O.P. and salted sodium silicate were studied and discussed by using IR and Zeta- potential measurements.

Jan 1, 1995

By J. J. Gusek, T. C. Richmond, R. W. Reisinger

A high-altitude (9,500-ft [2,900-m]) historic underground copper mine in Wyoming discharges neutral but copper-laden water into a pristine creek. Under a Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA) deferral agreement, the Wyoming Abandoned Mine Land Program performed site characterization and treatment studies in preparation for reclamation of the site. An integral part of the project included addressing the needs of a variety of interested and affected parties, including property owners, local populations, government agencies, and the media. This paper discusses an overall approach and specific methods employed to enlist public support for the project as well as some of the successes and failures experienced.

Jan 1, 2004

By Marcelino Cortina

It is known that underground bituminous coal mining in the Central Asturian Coal Basin (North of Spain) is a complicated task, due basically to the difficult geological conditions: thin and steep Seams with many faults and other disturbances. Therefore, it is not easy to decide what is the most suitable mining method for each of the seams, and problems in making the correct decision are encountered frequently. Because selections in the past have been inadequate an Expert System, ASTURLABOR;hulla, has been designed and will be developed' to provide accurate advice in the mining method selection process. The paper describes the major features of this Expert System and outlines the ASTURLABOR general project, which includes five other mining Expert Systems to complement ASTURLABOR-hulla.

Jan 1, 1989

By H. J. Handewith, W. D. Coski

This paper describes the development and testing of the RAMEX excavation system. Incorporating a synergy of low velocity, high energy impact and kerf cutting, this machine offers a competitive alternative to drilling and blasting in hard rock. It is a boom mining machine that incorporates the features of a lightweight roadheader and it can mine nearly any shape opening in hard rock. The RAMEX Tunneler has been developed to satisfy industry demands for a non-explosive, flexible, continuous and rapid underground rock excavation system. It will produce minimum ground vibration in the urban environment and allow the flexibility necessary for thin seam mining conditions. It will also reduce initial ground support costs and has a minimum impact on rock integrity. Developed by RAMEX Systems with cooperative research provided by the U.S. Bureau of Mines, this system, could produce the next step in the continuing evolution of mechanical mining systems.

Jan 1, 1989