Search Documents

By I. Sanchez

The development of the recent generation of large mining projects in South America has been challenging in many ways, but especially in the management of water in all its aspects. As a result, a number of projects have experienced difficulties and in some cases significant delays due to a lack of a clear and approved definition of the supply, use and discharge of water from mining and processing sites. The development of the recent generation of large mining projects in South America has been challenging in many ways, but especially in the management of water in all its aspects. As a result, a number of projects have experienced difficulties and in some cases significant delays due to a lack of a clear and approved definition of the supply, use and discharge of water from mining and processing sites.

Feb 23, 2014

By R. V. Ramani

Minerals, together with agricultural and forestry products, are the primary source of wealth produced in the United States. Although the production of minerals requires only a small fraction of the state's total land surface, as compared with either agriculture or forestry (Table 1), mining activities generally are much more disruptive to the land surface, and rehabilitation is more complex and costly. The past 10 to 15 years have witnessed a sharp increase in mineral exploration and mining, particularly coal mining, which has brought with it an increase in conflict over land use and an increase in negotiations for purposes of mineral prospecting and mining. The general increase in the production and consumption of coal and the particular increase in the percentage of coal extracted by surface mining methods coupled with a growing nationwide environmental consciousness have created increased public concern and in some cases outrage over mining activities. Although there is ample evidence to indicate that it is possible to plan for and design mining activities in such a way that they are compatible with other activities and can thus be made a part of a sequential land-use plan, there is a general lack of knowledge regarding the importance of mining as the provider of basic and essential raw materials to supply society's constantly expanding and increasing mineral needs. This lack of knowledge extends to such matters as land and mineral rights negotiations, the character of mineral deposits and minerals, mineral economics, and land-use planning.

Jan 1, 1977

By K. T. Brashear, N. Ripepi

"Over recent years, specifically following the MINER Act of 2006, an increasing number of manufacturers of underground mine seals in the United States have begun using a form of pumpable cement or shotcrete to create barriers separating the working and abandoned sections of underground coal mines. This seal material, while generally considered to be homogenous and solid, contains a network of microcracks, voids, and delaminations. Generally, it has been assumed that methane (CF4) leakage around these seals is a result of movement around the boundary interface between the seal and surrounding strata. Using a perfluorinated tracer compound, perfluoromethyl-cyclohexane (PMCH), the movement of gases can be monitored through seal material to observe how gases move though the material, both intact and with faulting in the material. This paper documents two large experiments where the movement of PMCH was monitored in the field, along with modeling confirmation using 3D visualization software. INTRODUCTION According to a report in 2007, there were over 14,000 active mine seals in underground U.S. coal mines alone (Zipf, Sapko, & Brune, 2007). These seals are used for both ventilation and safety purposes, to direct the flow of air away from the abandoned area of the mine and to help eliminate the propagation of explosions that can occur on the outby side of the mine seal. The atmosphere on the outby side of these seals typical consists of low levels of methane that have the potential of producing leakage along the face of the seal on the inby side. Methane leakage around mine seals has historically been attributed to the permeability between the seal and mine interface (McPherson, 1993). According to the United States Bureau of Labor Statistics (BLS) between 2003 and 2012 an average of 17 deaths occurred annually in underground bituminous coals mines. The only time during the ten-year period where the fatalities were higher than the average was in 2006 and 2010, years which had three major explosions occurring in underground coal mines in West Virginia and Kentucky. Two of the explosions were propagated through the mine by seal failure or methane leakage around newly poured seals (Light, et al., 2007) (Gates, et al., 2006). These recent events, and new regulations regarding seal strength (MINER Act), have created a need to monitor the condition of underground mine seals. BACKGROUND Measuring the permeability of solid materials, such as concrete or seal materials, can be a valuable tool in the field of non-destructible testing (NDT). By using an inert gas, such as nitrogen, injecting the gas into a solid structure, and measuring the resultant flow rate and pressure differential, this can provide valuable information about the structure. Studies have shown permeability can be affected by the stresses applied to the structure, as well as temperature and moisture (Choinska, Khelidj, Chatzigeorgious, & Pijaudier-Cabot, 2007) (Abbas, Carcasses, & Olliver, 1999)."

Jan 1, 2015

By A. Khoshnevisan

Molybdenum resources around the world are mainly associated with porphyry copper ores. Molybdenite (MoS2) is the main Mo mineral that has rhenium in its crystal lattice. This paper investigates the recovery of rhenium and molybdenum from a molybdenite concentrate using a hydrometallurgical treatment method. The molybdenite concentrate is leached with nitric acid and subjected to solvent extraction to recover and separate rhenium and molybdenum from the leached liquor. The effects of pH and the chemicals? concentration on extraction characteristics of Mo and Re are investigated to define the best condition for selective extraction of these metals. The tested leached liquor contained of 8.2 g/L Mo, 1.5 g/L Fe, 0.5 g/L Cu and 60 ppm Re. A good extraction efficiency, up to 94%, was achieved for Re from the leached liquor, where the extraction of other metals, such as Fe and Cu, was negligible. In particular, at very low pH, rhenium is extracted selectively from solution, while the extraction of molybdenum is less than 10%. After removing rhenium, molybdenum was extracted with LIX984N. The selectivity of molybdenum extraction over other metals in solution was significant. Nearly 94% of molybdenum can be extracted from the solution at a pH value of -0.12, without any interference from other metal ions such as copper and iron.

By R. V. Ramani, S. Shankar

The phenomenon of re-entrainment is seen in environments such as sand dune formation, soil erosion, fugitive dust emission and the spread of radionuclides from accidents involving nuclear weapons. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of ongoing research at the Generic Mineral Technology Center on Respirable Dust at the Pennsylvania State University on the development of methods to predict ambient dust concentrations in mine atmospheres (Ramani, 1983). The contribution of re-entrainment to the spatial and temporal concentration of dust in mine airways is being studied. The research has included wind tunnel and in-mine studies. A set of seven experiments was performed under controlled conditions in the US Bureau of Mines' Lake Lynn Laboratory mine. Two types of source coal dust, anthracite and bituminous, were subjected to various airflow rates and were subjected to walking by two different individuals. Six sets of instruments were used along the test section for sampling airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/sec. Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg/m3 (standard deviation = 0.03 mg/m3) from an initial value of 0.02 mg/m3. The concentration of all (total) airborne dust increased to 0.17 mg/m3 (standard deviation = 0. 10 mg/M3) from an initial value of 0. 02 mg/m3. The action of people walking, however, caused higher amounts of re-entrainment. The average concentration of respirable and total dust at the center of the mine airway increased to values of 0. 28 mg/m3 (standard deviation of 0.12 mg/m3) and 1.53 mg/m3 (standard deviation of 1.0 mg/m3), from initial values of 0.03 and 0.05 mg/m3, respectively. It was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal-dust bed. Depending on the level of activity and the amount of dust deposited in the mine airways, re-entrainment may become an important source of airborne dust in areas away from the point of actual mining.

Jan 1, 1996

By C. W. Overton

The operations of Bethlehem Copper are situated in the south-central interior of British Colombia at an elevation of 4900 feet above sea level. Main road and rail transportation systems pass through Ashcroft in the Thompson Valley, which is 28 miles by road from the minesite. The operation was the first low-grade open-pit porphyry copper mine in British Colombia. The minerals are chiefly chalcopyrite and bornite, while the rock is principally feldspar and quartz. In the outer fringes of the orebodies sane pyrite is present. Average grade of mill feed is 0.55% copper.

Jan 1, 1973

By Qingwen Shi, Brijes Mishra

The abstract discusses the use of numerical simulations to investigate roof fall in underground mines. It highlights the advantages of the discrete element method (DEM) in simulating large strain problems and fracturing processes, while acknowledging its computational limitations for large-scale problems. The study presents a 3D numerical model coupling the finite difference method (FDM) and DEM to simulate laminated roof failure in a coal mine. The model represents the laminated roof with bonded particles and discontinuities, while the surrounding rock is represented by continuum zones. The research analyzes the fracturing of the laminated roof as the entry advances, demonstrating the coupled method's ability to reproduce laminated roof failure.

Mar 17, 2022

By Karl R. Zipf

A tube bundle system (TBS) is a mechanical system for continuously drawing gas samples through tubes from multiple monitoring points located in an underground coal mine. The gas samples are drawn via vacuum pump to the surface and are typically analyzed for oxygen, methane, carbon dioxide and carbon monoxide. Results of the gas analyses are displayed and recorded for further analysis. Trends in the composition of the mine atmosphere, such as increasing methane or carbon monoxide concentration, can be detected early, permitting rapid intervention that prevents problems, such as a potentially explosive atmosphere behind seals, fie or spontaneous combustion. TBS is a well-developed technology and has been used in coal mines around the world for more than 50 years. most longwall coal mines in australia deploy a TBS, usually with 30 to 40 monitoring points as part of their atmospheric monitoring. The primary uses of a TBS are detecting spontaneous combustion and maintaining sealed areas inert. The TBS might also provide mine atmosphere gas composition data after a catastrophe occurs in an underground mine, if the sampling tubes are not damaged. TBSs are not an alternative to statutory gas and ventilation airflowmonitoring by electronic sensors or people; rather, they are an option to consider in an overall mine atmosphere monitoring strategy. This paper describes the hardware, software and operation of a TBS and presents one example of typical data from a longwall coal mine.

May 1, 2013

By J. A. Finch

A closed grinding circuit, typified by a ball mill-cyclone combination, is often required to treat a feed comprised of a variety of minerals of differing properties. Usually, the individual behaviour of the minerals is not assessed, a procedure which requires sizing and metal or mineralogical assaying of each size fraction. Further, sizing is frequently by screening to perhaps 325 mesh meaning that detail on the important -44 um fraction is unavailable. It is well appreciated that minerals can exhibit both individual classifying and grinding behaviour. Recognizing that cyclone classification results from differential centrifugal settling and acceleration rates, then minerals of differing specific gravity will exhibit individual mineral cyclone performance curves. If the minerals have differing grindabilities, then individual mineral rates of breakage may be expected. When treating an ore containing minerals of a range in specific gravity and/or grindability, individual mineral behaviour in the closed-circuit grind could be notable and perhaps important to the overall concentrator performance. An example is a lead-zinc ore, as shown by Kelsall et al.(1,2) This paper describes the individual mineral cyclone performance curves at sizes down to ti 10 um for the four major minerals at two lead-zinc concentrators; the Sullivan concentrator at Kimberley, British Columbia, and the Pine Point Mines concentrator at Pine Point, North West Territories, both operated by Cominco Ltd. In addition, individual mineral grinding behaviour for the four major minerals at the Sullivan concentrator is presented.

Jan 1, 1977

By S. K. Kawatra, J. A. Halt

"Low-grade iron ores are finely ground and processed to recover iron-bearing minerals. However, the iron-rich powder is too fine to be used directly in blast furnaces and most direct reduction furnaces, and must be agglomerated or pelletized into a usable product called “pellets.” Bentonite clay has traditionally been used as a binder to make iron ore concentrate pellets, but it is expensive and contaminates the pellets. Organic binders may be a viable alternative to bentonite clay. This manuscript reviews organic materials that have been used to make iron ore concentrate pellets. Included are discussions on the development of organic binders, common pros and cons to organic binder use, organic binder structure and its effects on agglomeration, and additives to organic binders.IntroductionIron ore agglomeration turns finely disseminated, low-grade iron ores into a usable product, called pellets. During pellet production, fine-grained, iron-rich minerals are liberated from low-grade ores, concentrated, and agglomerated into round balls that are thermally hardened or cold-bonded to form pellets. Pellets are then transported to blast furnaces or direct reduction operations where they are used to produce iron; iron is further refined and shaped into the wide variety of steel-based industrial and consumer products in use today.Over the years, pellet production has become increasingly more prevalent with the increased exploitation of low-grade iron ores and increased iron and steel consumption around the world. In 2010, world iron ore pellet production was 388 Mt. It could be argued that the current pellet production process has been enabled by the use of binders – practical experience has shown that it would be nearly impossible to agglomerate iron ore concentrates using rotary drums and discs without using a binder."

Jan 1, 2015

By Mark A. White

Arch Mineral has developed several computer programs that aid the surface mine planning function. These programs are utilized to perform long term projections for various area or semi-area stripping operations. The program generated reports include yardage, tonnage, quality and ratio information for the user-specified time periods. The projections are used to anticipate the annual budget, to compare alternative mine plans and to analyze acquisition candidates. The programs are user friendly, fast and accurate. Geological Grid File Two data files must be set-up and used in conjunction with the mine planning programs. These are a geological data file and a general input file.

Jan 1, 1984

By Alain S. Kivava, Olawale K. Aromolaran, Charles Nzolang, Anthony T. Bolarinwa, Georges M. Kasay

Rare earth elements (REEs) are crucial in high-tech and green technologies. The Democratic Republic of Congo (DRC), rich in mineral resources, shows potential for REE deposits in carbonatites, pegmatites, and placers. This paper reviews global REE resources, highlights potential REE targets in Africa, and emphasizes the need for further research and exploration in the DRC to unlock its REE potential.

Feb 4, 2022

By Justin Reed, Sara Bewley, Dwight M. Kinnes, Maryam Sadeghi, Ed Hart

This study compares wet gravity and dry magnetic separation for preconcentrating an allanite-rich rare earth ore from the Halleck Creek deposit. Material in the –300/+86 μm size range was treated to define a flowsheet that maximizes total rare earth oxide (TREO) recovery. The ore is dominated by feldspar and quartz, with hastingsite, an iron-bearing aluminosilicate. Because hastingsite’s density and magnetic response closely match allanite, it is difficult to reject using conventional methods. Two separation approaches were evaluated: MG12 spirals for gravity concentration and an Induced Roll Magnetic Separator (IRMS) for dry magnetic upgrading. MG12 spirals performed well in the rougher stage but provided limited gains when used as cleaners. When IRMS was applied as the cleaner stage, TREO grade and recovery improved substantially, showing that a dry magnetic cleaner circuit can effectively replace the wet gravity cleaner step. MG12 spirals remain suitable for highcapacity rougher duty, but dry magnetic separation delivers higher selectivity, simpler operation, and eliminates water use—offering a more efficient and sustainable preconcentration route in water-constrained environments.

Feb 22, 2026

By J. D. Miller

Physical separation of bitumen from low-grade Utah tar sand deposits containing a relatively high viscosity bitumen phase (Sunnyside and Tar Sand Triangle deposits) has been accomplished by traditional size reduction and froth flotation techniques. At appropriate experimental conditions more than 90 percent of the bitumen can be recovered in a concentrate, containing more than 20 weight percent bitumen, which should be a suitable feed material for subsequent hot water or thermal processing. The efficiency of bitumen recovery depends on the extent of size reduction, promoter and dispersant addition. Rejection of greater than 60 percent of the sand at ambient temperature and ease of water removal from the concentrate make such a process strategy both energy and cost effective. The energy required to achieve effective separation by the ambient temperature process is significantly less than the energy required for the recently developed hot water process. The flotation behavior of the tar sand has been analysed with respect to flotation pH, contact angle measurements and the apparent iso- electric point of the bitumen. The best flotation response at pH 7.8 to 9.0 can be correlated with the maximum in contact angle developed between the air bubble and bitumen surface and with the apparent iso-electric point of the bitumen (-pH 8.0).

Jan 1, 1981

By D. R. Nagaraj

Adsorption of sulfide collectors such as xanthate on pyrite has been studied extensively over several decades using a wide variety of techniques. In spite of this, there are unanswered questions as to the identity of adsorbed species on pyrite surfaces -dixanthogen vs. iron xanthate complexes. Far less is known in non-xanthate collector systems. We have used Secondary Ion Mass Spectroscopy (SIMS) successfully in the past to obtain direct evidence for the identity of the adsorbed collector species on copper sulfides, galena and Cu-activated quartz. The present study is an extension of the SIMS analysis to investigate the adsorption of xanthate, dithiovhosphate, dithiocarbamate, and modified thionocarbamates and thioureas on pyrite. Adsorption of these collectors on chalcocite was also studied for comparison. An attempt was also made to obtain SIMS spectra for pure dixanthogens at room temperature. Only in the case of dithiocarbamate (DTC) was there direct evidence for the presence of not only the collector dimer, but also iron-DTC complexes. On chalcocite, only the copper-DTC complexes were detected (no dimer). In the case of xanthate, the collector molecular ion and its S adduct -which are possible fragments from dixanthogen -were detected on pyrite, along with a fragment peak: suggesting Fe2X. For dithiophosphate, the collector molecular ion and Fe(DTP)(OH) complex were detected (no dimer). For modified thionocarbamate and thiourea, adsorption on pyrite was negligible.

Jan 1, 1997

By C. Bryce

Rhenium is primarily recovered as a by-product from molybdenum roasting circuits. However, rhenium is also present in copper heap leach solutions at very low concentrations and represents a potential new rhenium source. Freeport-McMoRan Copper & Gold has developed a new process using carbon adsorption followed by ion exchange or solvent extraction to concentrate rhenium from less than 1 ppm to 15 g/L. The product is compatible as a feed to an existing rhenium processing plant. A pilot plant operated at Freeport-McMoRan?s Sierrita mine has demonstrated the technical and financial feasibility of this new process.

Feb 23, 2014

By David Mast, Amanda Foote, Mina Shinouda

The Michigan DOT’s I‑75 Modernization Project, Segment 3, is a 30-year, $1.2 Billion design-build-finance-maintain project in Southeast Michigan. The scope includes building a nearly 4-mile long, 14.5-foot ID stormwater storage tunnel. The tunnel and pump station are being built concurrent with new roads and bridges, requiring multiple levels of design and construction coordination. Underground risks include the poten‑ tial for encountering granular soils, groundwater, and explosive gases. The new tunnel will be mined by a new open-face TBM and lined with a one-pass steel-fiber-reinforced precast concrete segmental lining. Shaft construction began in early 2020 and tunnel mining in July 2020.

Jun 13, 2021

By Rohan Fernando, David P. Snyder, John F. Burr, Susan M. Moore

"The Mine Improvement and New Emergency Response Act of 2006 (MINER Act Public Law 109-236) was passed by Congress in response to three major underground coal mine accidents in the United States that claimed the lives of 19 miners. The Act resulted in substantial changes in the underground coal industry relative to the use of technology for mine escape, rescue, disaster response and other areas where the lack of these technologies contributed to the fatalities caused by these tragedies. This year marks the 10th anniversary of the MINER Act, which makes it an opportune time to reflect on the events that led to its passage, the changes that have been made since then, and the work that remains to be done.As discussed below, the last decade has demonstrated tremendous cooperative efforts among mining operators, technology innovators, labor, The National Institute for Occupational Safety and Health (NIOSH), the U.S. Mine Safety and Health Administration (MSHA) and state regulators, resulting in substantial improvement of the technologies used for escape and rescue and noteworthy progress toward meeting many of the goals of the MINER Act. While the MINER Act and this article pertain primarily to coal mining, many of the technologies are equally applicable to any underground mining and have already found some acceptance outside of coal.Technology gaps targeted by the MINER ActThe MINER Act addressed several technology challenges:• Problems with donning and switching between self-contained, self-rescuers (SCSRs).• Poor visibility in smoke.• No wayfinding assistance for escape from the mine.• Limited breathable air supply.• Inability to locate trapped miners.• Inability to communicate with trapped miners.• Failure of mine seals."

Dec 1, 2016

By David B. Costain

Three dimensional surface approximations are important means of evaluating physical and environmental factors that affect surface coal mining and reclamation. Computer approximated surfaces are projected as an array of square grid cells where individual cells define each parameter value respective to locations on the grid. Grid surfaces or grid cells within a surface can be compared or modified through application of standard mathematical functions. Surface approximations can be used to define the quantity and quality of marketable coal and to evaluate thickness and quality of overburden. Surface approximations also can be used to evaluate overburden swell factors wherein changes in post-mine topographic relief are related to expansion of unconsolidated materials in the backfill. Application of computer approximated surface to analysis of approximate original contour (AOC) standards allows an assessment of the quantity and geographical displacement of overburden and the distribution and numerical level of slope.

Jan 1, 1984

By HASAN SERKAN GOKCEN, SERKAN CAYIRLI

The purpose of this study was to investigate the dry grindability of calcite powders in a vertically and horizontally orientable laboratory batch type stirred mill. The experimental results were evaluated using stress intensity analysis. The performance was also compared in terms of mill orientation. The results showed that the d50 values decreased with increasing stress energy down to a certain point and then increased for both milling orientations. Even though the optimum stress energies for both vertical and horizontal orientations were in the range of 1*10−3 to 5*10−3 Nm at 750 and 1500 kJ/kg energy consumption, the product size was finer for the horizontal orientation at the same stress energy value. Additionally, to the best of the authors’ knowledge, this is the first study to compare mill orientation (vertical vs. horizontal) for the same mill and under the same test conditions.

Apr 21, 2021