Search Documents

By Frank Agyemang, Zainab Nasrullah, Richard LaDouceur, Mehran Saddat

To sustain the circular economy, defence applications, and other renewable technologies, recycling rare earth elements (REEs) and other critical elements from their secondary resources is important. This cause has resulted in rigorous research and development for viable extraction and separation of REEs. Previously, Sm-Co recycling has been done with technologies, which fall under the categories of pyrometallurgy, physical separation, and hydrometallurgy. All these methods have limitations associated with energy, cost, and environment. Reportedly, the chemical leaching technology has successfully recovered and separated Sm-Co. Still, it has limitations associated with slow mass transfer and leaching kinetics, and there is a need to intensify the process to make it time efficient. This approach has also adversely impacted the environment by an extensive use of toxic, corrosive, non-selective, and expensive reagents. In this research study, chemical leaching of Sm-Co was performed using this new class of solvents, Deep Eutectic Solvents (DESs), which fall under the category of ion metallurgy. Four different DESs were used, proven to be green, non-toxic, biodegradable, cheap, and selective for cobalt over samarium by 82% leaching conversion. To improve the slow mass transfer and leaching time, this new technology of resonant vibratory mixing (RVM) was also tested. RVM intensifies mixing by establishing near instantaneous, low energy mixing conditions through resonance. It has been shown to improve the adsorption kinetics and was tested for the leaching kinetics. Four combinations of DESs were prepared, which are made up of two quaternary salts: Choline Chloride and Tetra Butyl Ammonium Chloride, and three organic compounds: Oxalic Acid, Urea, and Ethylene Glycol. These combinations were used for chemical leaching of Sm-Co with leaching factors of time, temperature, and type of DESs. After leaching, the samples were tested with and without resonant vibratory mixing with conditions of time, intensity (%), and type of DESs. Samples were analysed with Induced Coupled Plasma - Optical Spectroscopy (ICP - OES). Future work will involve a life-cycle assessment to assess the RVM technology with other conventional mixers, and an extensive study of DES properties to improve selective leaching.

Feb 1, 2025

By B. Samanta

This paper highlights the use of an innovative mine production scheduling scheme for grade-control planning tasks that take into consideration grade-model uncertainty. The scheduling exercise has been carried out with the help of a multiobjective genetic algorithm (MOGa) for the production scheduling operations. The underlying motive behind the use of MOGa has been the generation of a set of pareto optimal solutions to meet the goals of the target-grade specifications for the considered multiple grade attributes. Several new concepts related to MOGa formulation, in particular the mutation operation and the convergence criteria of this algorithm, are proposed in this paper. The modeling of grade uncertainty into the scheduling outputs has also been incorporated through a set of conditional simulated grade maps. The proposed scheme of production scheduling operations has been applied for the grade-control planning operations in an iron ore mine to meet the targeted grade specifications of iron, silica and alumina, and a risk analysis has been performed to this end.

Jan 1, 2013

By Qingwen Shi, Gang Xu, Shuwen Wang, Brijes Mishra

Pressure relief borehole is one of the most effective methods to treat coal burst in deep-buried coal seams. However, due to the large amount of randomly distributed fractures in the coal body and the varying stress environments in underground coal mines, there is no practical method to assess relief boreholes by far, which brings problems for borehole design and construction. This study focuses on the assessment of relief boreholes in a single driving entry wherein the impact of mining panels on relief boreholes is eliminated. A practical method, focusing on field monitoring of borehole deformation with a new device, is developed to evaluate the single driving entry’s relief boreholes. This method is applied to a Chinese coal mine. The application results showed that the convergence process of the boreholes showed a three-phase characteristic. Phase one involves the fastest deformation, reaching up to 8% in the first 3 to 4 days. Phase two lasts longer and converges more, reaching up to 30% in 4 months. Phase three stays balanced until the excavating face moves. The three-phase characteristic indicates that a large diameter of the borehole ensures relief efficiency because the borehole provides adequate space for deformation throughout its life span. In addition, it is verified that long boreholes and slow footage improve relief efficiency by providing adequate time for the boreholes to work. The application proposes that boreholes in the test coal mine need to be drilled larger and longer for optimization.

Oct 19, 2021

By H. L. Ehrlich

Marine manganese nodules harbor a mixed population of manganese-oxidizing and -reducing bacteria, as well as bacteria that do not act on manganese. They also host phagotrophic protozoa. Out of several laboratory studies, one line of investigation indicates that some kinds of bacteria found on nodules can catalyze the oxidation of Mn2+ bound to Mn(IV) oxide at the surface of nodules at in situ temperature and pressure. In the absence of appropriate bacteria, the rate of oxidation of the surface-bound Mn2+ is significantly slower. How Fe(III) is incorporated is still unclear. Base metals such as Cu, Ni and Co, which are usually found in marine nodules in various quantities, may be incorporated through scavenging by Mn(IV) oxide. Laboratory evidence shows that some other bacteria on nodules can reduce the Mn(IV) oxide to Mn2+ in the presence of an appropriate source of reducing power in the form of organic carbon. The reduction of Mn(IV) oxide mobilizes manganese and trace metals such as Cu, Ni, and Co in the nodules. These bacteria reduce Mn(IV) whether oxygen is present or not. They could be harnessed in the bioleaching of nodules. The manganese(IV)-reducing bacteria and the bacteria that neither oxidize nor reduce manganese are thought to keep the organic matter in the nodule environment sufficiently low to favor bacterial manganese-oxidation, which in laboratory tests is inhibited by excess organic carbon. The preying by the protozoa on the different kinds of bacteria is thought to control the bacterial population on nodules and ensure continued growth of the manganese-oxidizing bacteria and the nodules. To eliminate interference from seawater salts in the bioleaching of Mn, Cu, Ni and Co, it may be more advantageous to use terrestrial Mn(IV)-reducing bacteria than the Mn(IV)-reducing bacteria resident on nodules. The terrestrial bacteria would allow bioleaching in fresh water. Unlike the marine bacteria, most terrestrial bacteria studied to date reduce Mn(IV) oxide only anaerobically. A general outline for an anaerobic bioleach process of marine nodules with freshwater bacteria is discussed.

Jan 1, 2000

By P. S. Sundar

A laboratory method for the simulation of in-situ leaching of uranium was developed under contract to the Interior Department's Bureau of Mines. Simulation tests using sulfuric acid, ammonium bicarbonate and sodium carbonate as reagents and hydrogen peroxide as oxidant were carried out with representative ores from Texas and Wyoming. The tests not only yielded recovery rates of uranium and permeability changes, but also qualitative inferences on the chemical and physical phenomena which occur underground. Leaching with basic solutions was found to be kinetic constrained and with acid solutions, equilibrium constrained. The rapid permeability changes observed when leach solutions were introduced, were probably caused by gas blockages in the packing. Precipitation of calcite or gypsum and the reaction of clay to leach solutions had slow and gradual effect on the packing permeabilities.

Jan 1, 1978

By K. A. Lewandowski

Heap leaching efficiency is reduced by poor solution flow characteristics (channeling and ponding), which result from compaction and fines migration. Agglomeration of the ore can prevent compaction and immobilize fines, but copper leaching requires an acid-resistant binder to stabilize the agglomerates. Until now, there has not been a satisfactory way to evaluate whether a binder was effective, other than squeezing a handful to see if it ?feels right.? Procedures have been developed to quantitatively determine whether a binder produces agglomerates that can withstand compaction in an acidic solution, and have identified several binders that will provide sufficiently compaction-resistant agglomerates for copper heap leaching. Keywords: Copper heap leaching, Binder performance, Compaction

Jan 1, 2010

By J. R. Patts, A. B. Cecala, E. J. Haas

Exposure to respirable crystalline silica (RCS) remains a serious health hazard to the U.S. mining workforce who are potentially exposed to RCS [1,2] as various ore bodies are drilled, blasted, hauled by truck, crushed, screened/sized and transported to their destinations. To examine a method for assessing RCS exposure using a NIOSH-developed video exposure monitoring (VEM) technology (referred to as Helmet-CAM), video and respirable dust concentration data were collected on 80 miners across seven unique mining sites. The data were then collated and partitioned using a thresholding scheme to determine exposures that were in excess of 10 times the mean exposure for that worker. Focusing on these short-duration, high-magnitude exposures can provide insight into implementing controls and interventions that can dramatically lower the employee’s overall average exposure. In 19 of the 80 cases analyzed, it was found that exposure could be significantly lowered by 20 percent or more by reducing exposures that occur during just 10 minutes of work per eight-hour shift. This approach provides a method to quickly analyze and determine which activities are creating the greatest health concerns. In most cases, once identified, focused control technologies or behavioral modifications can be applied to those tasks.

By Stephen F. Munsell

The development of transportation systems for mined materials has historically been characterized by steadily increasing sizes in basic hauling units. This is especially true for open pit mines for which success is dependent upon the economical transportation of vast quantities of material. The depletion of high grade ore reserves has mandated a tremendous increase in the size and complexity of the ore haulage systems necessary for open pit mines, These increased demands were served by rail haulage systems in the early large open pit copper mines while later developed properties opted for the flexibility and lower initial costs of truck haulage. Now, we find the trucks being displaced as large overland belt conveyors tackle the problem of handling these ever larger quantities of low-grade ores with accompanying overburden ratios that can run as high as 10:1 or even 15:1. The basic development of large conveyors with shiftable sections and modular belts has generally taken place overseas, during the last few decades. The coal fields of central Europe proved an ideal testing ground for conveyor innovation because the low density and natural friability of the material created an ideal medium for transporting by belt conveyor. Now these proven ideas are being considered for and implemented into both the soft and hard rock mining industries of the United States.

Jan 1, 1978

By Meghan Murphy, Yiming Sun, Kush Chohan

DTX is a 1.3-mile-long rail extension being constructed by Transbay Joint Powers Authority to extend Caltrain rail service and future California High Speed Rail service to downtown San Francisco. It includes a 3,352-foot-long mined tunnel with a cross section varying from 50 to 60 feet wide and 43 feet high to accommodate two- and three-rail tracks. DTX will be excavated in mixed-face and Franciscan Formation with ground cover ranging from 40 to 85 feet. This paper discusses how mined tunnel design has evolved since the initial preliminary design phase over 10 years ago. The current design concept for tunnel construction is also discussed.

Jun 13, 2023

By J. H. Gwynne

[ ]

Jan 1, 1962

By W. M. Husslage

The permeability in the blast furnace shaft is adversely affected by low temperature reduction degradation of sinters. The fundamental cause is an expansion of the iron oxide phase resulting from reduction of hematite to magnetite. The present study showed that expansion behavior during the hematite / magnetite reduction step and the resulting microstructure are strongly influenced by the reduction temperature (viz. partial oxygen pressure), the reducing agent and the nature of the hematite. The reduction rate is of minor importance. A reduction mechanism is proposed, explaining the dilation behavior and the magnetite microstructure. The results can provide better insight into reduction degradation behavior.

Jan 1, 1998

By P. T. Bissert, L. Yan, M. D. Klein

"Federal regulations require the installation of refuge alternatives (RAs) in underground coal mines. Mobile RAs have a limited ability to dissipate heat, and heat buildup can lead to a life-threatening condition as the RA internal air temperature and relative humidity increase. The National Institute for Occupational Safety and Health Office of Mine Safety and Health Research performed heat testing on a 10-person tent-type training RA and contracted ThermoAnalytics, Inc. to develop a validated thermal simulation model (TSM) of the tested RA. The TSM was used to examine the effects of the constant mine strata temperature assumption, initial mine air temperature (MAT), initial mine strata surface temperature (MSST), initial mine strata temperature at depth (MSTD), and mine strata thermal behavior on RA internal air temperature using 117 W of sensible heat input per simulated miner. For the studied RA, when the mine strata temperature was treated as a constant, the final predicted RA internal air temperature was 12.8°F lower than it was when the mine strata thermal behavior was included in the model. A 10°F increase in the initial MSST resulted in a 7.1°F increase in the final RA internal air temperature, whereas a 10°F increase in the initial MSTD yielded a 2.5°F increase in the final RA internal air temperature. INTRODUCTION Since 2008, the Mine Safety and Health Administration (MSHA) has required the installation of refuge alternatives (RAs) in underground coal mines (1). MSHA requires that RAs provide an environment with breathable air for entrapped miners for a 96-hour period. Heat buildup inside an occupied RA is a serious concern. Without a means to dissipate the heat and humidity generated by the occupants and the carbon dioxide scrubbing system, the temperature and humidity inside RAs could lead to severe discomfort or heat stress depending on the mine ambient temperature before and during occupation of the RA. NIOSH recommended an apparent temperature limit of 95°F in its 2007 report to Congress (2). In 30 CFR 7.504, MSHA has specified a maximum apparent temperature of 95°F inside an occupied RA (3). The apparent temperature is calculated using both air temperature and relative humidity (4). Calculations could be used to determine if the air within an occupied RA will reach the apparent temperature limit. In these calculations, in order to simplify the problem, the mine temperature could be assumed to remain constant. With this assumption, the effects of the mine strata thermal mass and thermal conductivity on the heat buildup in an RA are ignored. OMSHR research has shown that the mine air and strata temperatures surrounding an RA increase when subjected to the heat of an occupied RA (5). Thus, calculations performed with the assumption that the mine temperature is constant would under-predict the resulting dry-bulb temperature and apparent temperature for a given RA occupancy. The mine air temperature has been used as the basis for RA temperature calculations. However, research has not been used to confirm that the mine air temperature is the appropriate basis."

Jan 1, 2016

By T. M. Yegulalp

A new explanation of the scale dependency of the strength properties of rock is presented based on the theory of extremes. A review of past work on specimen size strength relationship is followed by an introduction to the fundamentals of the underlying theory of extremes and its relationship to the scale effect on the statistical properties of the strength distribution. It is shown that the weakest link theory is directly related to extremal statistics and properties of strength distributions of rock can be derived as a function of the specimen size. Three sets of Brazilian test data are used to demonstrate the use of this approach.

Jan 1, 1992

By Klaus Schönert

In the analysis of comminution processes, it is necessary to have a detailed knowledge of such sub-processes as: (i) The transportation of the particles to the zone where they are stressed, (ii) The stressing of the particles to a level high enough for breakage, (iii) The removal of the fragments that are smaller than the limit size from the grinding zone, and (iv) The prevention of agglomeration of the fine fragments. The breakage phenomena of particles is the most difficult sub-process to understand. It can be understood only by applying the principles of fracture physics to obtain information about the stress-strain field in particles which are loaded either by compression or by impact, and by using this theoretical knowledge to interpret experimental results obtained from single particle crushing studies. It is not only of academic interest to know how a particle breaks, but also it is important for practical applications because it provides a basis for evaluating both the direction and limitation for any potential comminution improvement.

Jan 1, 1971

By Terry B. Linde, William M. Dowall

The recently completed In-Pit Crushing and Conveying Project at Phelps Dodge's Morenci Mine is rated among the world's leading materials handling projects. The operation involves the crushing and transport of more than 109,000 tonnes per day of copper ore, utilizing regenerative conveyors capable of providing over 5.5 megawatts (7,000 hp) of equivalent electrical energy. This paper describes the key aspects of the project and includes: Original project objectives; System design criteria; System description; Optimization studies; Major design features; Equipment description; and System commissioning.

Jan 1, 1993

By Gary MacDonald

What is the primary function of an impact assessment? Many people at the International Association of Impact Assessment?s (IAIA) annual conference said that it is time to return to the fundamentals and consider the underlying drivers of impact assessments ? human health, safety and security. This fall, managers struggling with those fundamentals will receive extra support when a new course focusing on health and socially responsible security is launched online and in British Columbia, Canada, home to many of the world?s junior miners. Now in its 33rd year, the IAIA conference recently held in Calgary, Canada, typically brings together a range of professionals who work in the impact assessment field, including academics, as well as people conducting applied disciplines, such as social and environmental performance management. It is a chance for people grappling with how to assess impacts from projects (for example, dams, mining and other extractive projects), to compare notes and to talk about developments in how to measure, track and report on them. The comments about returning to fundamentals rose as participants talked about the ongoing and increasingly recognized divergence between three main impact assessment streams: environmental, social and health (EIA, SIA and HIA, respectively). Discussions in sessions and in the corridors included calls for streamlining, for integration, for improvement and sharing of practice ? particularly in the HIA stream, where those deeply engaged in the health discipline questioned how HIAs and their intended outcome of protecting human health can be better integrated into the EIAs or SIAs that dominate the impact assessment realm. EIAs and SIAs have become the main tool, particularly from a permitting perspective for large-scale mines, but seem to leave projects with little real information about what they need to do. Human health is not the only concern re-emerging. Although not reflected at the conference, there appears to be an emerging understanding of the need to link the determinants of health with socially responsible security practices. Companies conducting independent social performance assessments for international financial institutions based on the International Finance Corporation?s Environmental and Social Performance Standards increasingly wrestle with both community health and security issues as extractive companies encounter challenging social environments around the world. Once again, the intended outcome is to better protect human health, including avoiding health impacts from conflict, abuses and violence.

Aug 1, 2013

High-pressure grinding rolls (HPGR) are an accepted, but continuously expanding, comminution technology. The copper industry has a growing need to process harder ores with progressively lower grades, more challenging metallurgy and increasing demand for efficient bacterial leaching applications. This has resulted in a major focus on HPGR use in a crushing circuit. If the industry is to increase leach extraction while lowering energy costs in high-throughput hydrometallurgical operations, HPGR will be of inherent significance. The following paper summarizes test work on copper leach ores utilizing the benefits of HPGR comminution, while increasing several critical metallurgical parameters. Based on the current work and previous investigations, it was found that HPGR comminution within a crushing circuit, in specific instances, can result in 2 - >10% increases in cop-per extraction. The tested variables are crush size, rock type and copper mineralogy dependence. Various other process parameters may also be optimized.

Jan 1, 2011

By Shilpa S. Haramkar, Bhaskar N. Thorat, Sachin V. Jadhav

The filtration of phosphogypsum is a ubiquitous step in the manufacturing of phosphoric acid. It is highly desired to achieve the minimum concentration of P2O5 in the phosphogypsum cake. This work is aimed at addressing P2O5 losses in phosphogypsum (PG) along with the recovery of P2O5 from slurry by using constant pressure filtration at 1 bar pressure. Laboratory tests were carried out in the phosphoric acid production plant situated in Paradeep, India. Recycled water source near acid plant (i.e., pond water) was used for cake washing to reduce the burden on fresh water stock. The findings indicated that pressure filtration offered the most effective P2O5 recovery (nearly 93.48%). The moisture was reduced to 14–16%, and watersoluble P2O5 in the gypsum cake was found to be negligible. A narrow particle size distribution was observed, which offered effective filterability with average cake resistance of 2.38 × 1010 m/kg, indicating a moderately separable cake.

Aug 23, 2023

By S. Dixon

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries to be developed in recent years Minera Peñasquito, S.A. de C.V., a wholly owned subsidiary of Goldcorp Inc. has developed the Peñasquito property to produce an average annual production of 120 kilo tonnes of lead containing 0.5 million oz gold and 30 million oz silver and 250 kilo tonnes of zinc containing 20 thousand oz gold and 1.5 million oz silver.. The Peñasquito property covers a 39,000 hectare area in the western half of the Concepción del Oro district in the northeast corner of Zacatecas State, Mexico, approximately 24°45'N latitude/101°30'W longitude. The sulfide reserves are 1,009 million tonnes containing 3.33 million tonnes of lead, 7.26 million tonnes of zinc, 16.5 million ounces of gold and 1,000 million ounces of silver. This paper describes the work to justify the installation of HPGR to process the crushed SAG mill pebbles. The SAG mill-Ball mill and Cone crusher (SABC) grinding circuit is an accepted grinding circuit to optimize power consumption relative to throughput. The installation of a HPGR to process the Cone crusher product is the next step in optimizing the power consumption relative to throughput. The concern expressed by some on not moving on this change in grinding circuit was the capital and operating cost of a HPGR. The pebbles from the SAG mill can be the more abrasive and are the harder particles of the ore. Goldcorp investigated the wear and processing costs of installing a HPGR to treat the crushed pebbles. The conclusion was the installation would be a very positive economic factor in the operation of Peñasquito. This is the first application of the use of HPGR to process crushed pebbles. Minera Peñasquito and M3 Engineering selected Polysius to provide a Polycom 2417 with twin 3,000 kW drives. A comprehensive test program at Polysius has shown for 7% higher circuit power it is possible to get approx 23% higher tonnage. This coupled with full utilization of the SAG and Ball Mill available energies and with proper control of the transfer size from the SAG to Ball mill circuit there is the potential to achieve 65,000 mtpd per line or a 30% total capacity increase. The cost of power for this increase in grinding capacity is 4.8 kWh/tonne.

Jan 1, 2010

By T. F. Tomb

Although the number of operating longwalls (approximately 100) has remained relatively constant over the last five years, longwall production levels have significantly increased and have in some cases more than doubled. As a result of the increase in production, control of respirable dust continues to be a problem. Therefore, the Mine Safety and Health Administration (MSHA), Pittsburgh Health Technology Center, Dust Division, initiated a study to investigate the availability and adequacy of technology for controlling dust on longwall mining operations. The study involved 23 longwall mining operations in three different Coal Mine Safety and Health Districts. Each operation was visited for a full shift. Respirable dust samples were collected on face personnel and at fixed locations along the face. Parameters in place to control dust were noted with special emphasis being placed on obtaining quantitative data relative to ventilation, headgate dust controls, cutting drum sprays, external machine sprays and cutting sequence. Attempts were made to correlate dust control parameters in place at the time of the visit to dust concentrations measured at the tail, on the tail shearer operator and to the average concentration of dust determined from averaging all the measurements from the occupations sampled. The parameters in place to control dust were also compared to the gamut of technology known to be available to control dust. This paper presents a discussion on the effectiveness of the parameters in place to control dust and on the availability of technology for the control of dust on longwall mining operations.

Jan 1, 1990