Search Documents

By A. L. Hinde

Ideally, mill circuits should be controlled so that excessive random disturbances are reduced in frequency and amplitude. It is difficult to derive an objective measure of the effectiveness of any chosen control strategy. Often, the response of the circuit to pulse or sinusoidal disturbances is used as a measure of the effectiveness of control, but this is not adequate in many circumstances because such disturbances bear little resemblance to those that occur in practice, and such an approach cannot be easily related to the profitability of the reduction process. A superior approach appears to be the application of the theory of stochastic processes. This theory permits both real process disturbances to be modelled accurately, and useful objective functions for control to be derived. A test of the usefulness of stochastic theory in mill control was made on the gold ore milling circuit shown in Figure 1. This circuit was fed with an ore which had a liberation characteristic such as that shown in Figure 2. It is simple to show that, for such a liberation characteristic, the recovery of valuable mineral will vary as the standard deviation of the particle mass-size distribution varies even though the mean particle mass-size is kept constant. Similarly it may be shown that excessive perturbations in the circulating load in a milling circuit such as that shown in Figure 1 can affect liberation. Figure 3 shows how, as the cyclone feed density increases and the sump water addition decreases at constant sump level, the cyclone operation becomes unstable and the discharge "ropes? with a consequent catastrophic coarsening in product size. By minimising the variance of the circulating load it is possible to reduce the probability of initiating instabilities of this nature.

Jan 1, 1977

By Edwarde R. May

The Flambeau volcanogenic massive sulfide deposit located in northwestern Wisconsin occurs within the southern lobe of the Canadian Precambrian Shield. The steeply dipping tabular body occurs in a complex pile of cyclic schistose intermediate to felsic fragmental volcanics. No chloritic alteration pipe is recognized but adjacent rocks have undergone magnesia metasomatism and subsequently were metamorphosed to the upper greenschist and lower amphibolite facies. Although modest in size the deposit is of special interest in that it has an extensive and well preserved supergene enrichment blanket. Economic minerals found within a pyritized quartz-sericite schist are chalcocite and bornite overlying primary chalcopyrite.

Jan 1, 1976

By T. R. Kostecki, A. J. S. Spearing, G. S. Esterhuizen, K. V. Jessu

Discontinuities are geologic occurrences in rock and when present within a pillar, reduce the strength of the pillar. Empirical formulas that are commonly used to determine pillar strength do not explicitly take into account the presence of discontinuities and thus can overestimate the pillar strength. The effect of discontinuities on the strength of pillars has been investigated using numerical models, but in these models, the discontinuity strike was parallel with the pillar faces. In this study, fully three-dimensional hard rock pillars were simulated using numerical modeling to understand the effect of the discontinuity dip direction on square and rectangular hard rock pillars. Based on the results, recommendations to assess a pillar’s strength in the presence of a discontinuity are discussed.

Jan 1, 2018

By K. Zabrusky

Epithermal vein systems are often modeled as simple, discrete high grade structures within low grade host rock. However, geologic setting and structural preparation influence how such vein systems form. In structurally complex areas, veins may follow several structural trends and occur on a variety of scales. Geologic and grade modeling within such complex structural regimes can be difficult as individual veins cannot be delineated from host rock based on grade alone. Structurally complex areas require a different approach than traditional discrete vein modeling. Presented herein is a study of a structurally complex area that hosts vein mineralization to be mined underground. All veins could not be modeled discretely, so an alternate approach was needed. Major structures were modeled using surface and underground mapping and were then used to create a structural trend for the area. This trend was used to guide 3D grade shell construction. The grade shells replaced 3D vein solids for grade estimation in order to mitigate the influence of high grade samples. Structurally guided grade shell construction offers a more effective modeling method than discrete vein modeling in deposits that are structurally complex.

Feb 23, 2014

By G. Davis

It is well known that the anticipated mineral price at the start of a prospective mineral project can have an overwhelming effect on a property's ex ante value. However, possible price movements throughout the life of a project can also have an impact on this value. This paper demonstrates how different potential price paths can affect project value. When considering commodity price projections for mine valuations, it is thus necessary to estimate not only the expected commodity price at the start of the project, but also the manner in which that price is likely to fluctuate throughout the project's life.

Jan 1, 1995

By D. S. Choi

The paper presents the result of analysis of subsidence data collected from coal mines operating in Northern West Virginia and Southwestern Pennsylvania. A particular emphasis la placed on the measurement of the angle of draw for the protection of surface structures.

Jan 1, 1986

By Darrell E. Young

This presentation will define what talc is, how it is mined and processed, and how talc is used in the paper industry. It will also give you some idea about who Luzenac America is and from where it came. Luzenac America was formed in July, 1992 as a result of the acquisition of the talc assets of Cyprus Minerals by RTZ of the United Kingdom. Cyprus Industrial Minerals was then merged with the other RTZ talc interests under the Luzenac name. Luzenac is a town in the Pyrenees of Southern France -and the home of Talc de Luzenac, RTZ's first talc acquisition. The Luzenac Group is the largest talc producer in the world.

Jan 1, 1993

An open pit production planning method for stage mining is presented in this paper. The method brings solutions to the four most important parameters in stage mining : 1) the number of stages, 2) the size and geometry of each stage pit, 3) the mining sequence of the benches in the stage pits, and 4) the time of transition from one stage to the next. The method can also simultaneously optimize the ultimate pit, mine life, and production rate in each stage.

Jan 1, 1996

By John N. Murphy

In fiscal 1996, the US Congress directed that the US Bureau of Mines (USBM) be closed. Certain functions were reassigned to other agencies. The remaining employees were separated and the unoccupied sites were decommissioned. As a result, 12 locations were closed and about 1,200 employees were terminated in March 1996. About 600 employees at five locations were reassigned to other federal agencies. This article provides a summary of the continuing functions, the agencies involved and the points of contact for each continuing function. The functions that were discontinued are also identified. The functions that have been maintained and transferred to other agencies are: ? Portions of USBM's Mineral Information and Analysis program formerly conducted in Washington, DC and Denver, CO were assigned to the US Geological Survey (USGS). ? The Mineral Land Assessment program in Alaska (Anchorage and Juneau) was transferred to the US Bureau of Land Management (BLM). ? The Health and Safety Research program in Pittsburgh, PA and Spokane, WA was reassigned on an interim basis to the US Department of Energy (DOE). In fiscal year 1997, it was permanently assigned to the National Institute for Occupational Safety and Health (NIOSH). NIOSH is part of the Centers for Disease Control and Prevention within the US Department of Health and Human Services. ? Environmental Research at Pittsburgh, PA was assigned to DOE. ? Materials Research at Albany, OR was assigned to DOE. ? The helium program was assigned to BLM, where it will be managed pending privatization. ? Coal and noncoal mine maps were transferred to the Office of Surface Mining Reclamation and Enforcement (OSMRE). The following locations were closed: ? Research centers in Denver, CO; Minneapolis, MN; Reno, NV; Rolla, MO; Salt Lake City, UT and Tuscaloosa, AL. ? Field operations centers in Denver, CO and Spokane, WA. ? Washington, DC headquarters office. To provide a concise picture of all of the affected functions, the following is a synopsis of the USBM program functions and facilities immediately before the closure. There were two principal programs: information and analysis, and research.

Jan 1, 1997

By D. R. Taylor

The use of clay granules as carriers for pesticides dates from the early 1940's and by the present day represents a business conservatively estimated at between 200 -300 thousand tons / year in the U.S. alone. Aside from economic and specific target pest efficacy advantages, the use of clay granules as pesticide carriers also delivers a number of environmental benefits which will be reviewed. Topics to be discussed will include: I) drift control (versus liquid sprays), 2) mobility (in the environment), 3) worker safety, and 4) transportation (spill) safety.

Jan 1, 1999

By T. Y. Yan

A method has been developed to remove calcite from the leaching circuit in the uranium in situ leaching system. The process involves injecting the leachate and a pH control agent tangentially into an inverted cone reactor containing calcite seed catalyst. The leachate can be treated at high throughput to obtain clear effluent containing 5 ppm or lower Ca. Both lime and ammonia are effective pH control agents and consumed according to stoichiometry.

Jan 1, 1983

By Zygmunt Sadowski

Problems encountered in barite flotation from various waste materials such as spent drilling muds are likely to be closely connected with the effect of chemical additives and metal ions present either added or present as contaminants, on the flotation. Fuerstenau and Palmer (1976) have studied in detail the adsorption of multivalent cations onto oxide and silicate minerals. It was observed that the adsorption of a multivalent metal species exhibits a sharp pH dependence which is related to the formation of hydroxy complexes of the metal ions in solution. Investigations on the recovery of barite from tailings ponds and mining wastes (Sullivan and Lamot, 1981) have shown that such barite materials can contain large quantities of carbonate and silicate minerals (including clay minerals). Also iron oxide slimes can be present. From these substances cations such as Ca2+, Mg2+, Fe2+ and A13+ can potentially dissolve and be present in the aqueous phase accompanying the various minerals. These ions and their hydrolysis products can have a substantial effect on any subsequent flotation scheme. The present study investigates the effect of the noted ions on both the stability and electrokinetic behavior of barite suspensions.

Jan 1, 1986

By Martin P. Schroeder

"Challenges have emerged as subway systems age and as new tunnels are bored in congested corridors or in high-risk environments. To help public transportation agencies address tunneling challenges, the American Public Transportation Association has convened numerous independent industry peer reviews composed of top experts in their fields to come together and provide recommendations and solutions. This paper provides case histories of peer reviews that include topics such as boring through toxic soils, boring underneath existing tunnels, retrofit of tunnel ventilation systems, and mitigation of water intrusion. Peer reviews are applicable to all tunnel projects worldwide. The paper will highlight the conditions of these challenges, peer review recommendations, steps taken to reach agreement, and the successes that resulted, which led to major changes, new legislation and reduction of risk. INTRODUCTION Public transit agencies face many challenges in maintaining and expanding safe transit operations, especially as systems age, ridership expands, and budgets remain flat. The development of new industry standards and federal safety regulations places further demands on transit systems, with compliance often taxing in-house resources. Studies of the state-of-good-repair across US public transit systems indicate a current backlog of $84 billion in maintenance projects, which will require an investment of $18.2 billion per year to eliminate the backlog by 2030[1]. Systems not in a state-of-good-repair may not operate efficiently, may not be available to meet the growing ridership demands, and may not meet required safety goals or reduction of risk. Innovation is another clear need transit agencies have for improving system performance and lowering operating costs.To meet these challenges, transit agencies often turn to industry peer reviews for guidance and recommendations as part of their overall strategy to maintain and grow the safe operation of their systems. As a service to its members, the American Public Transportation System (APTA) has developed an industry peer review program designed to give agencies opportunities to learn from each other and help them address challenges in operations, engineering design, and construction of their systems. Over the past 20 years, APTA has performed hundreds of peer reviews covering all aspects of transit system operations from fare collection to agency organization, project delivery methods to safety culture, and engineering design including tunneling and tunnel fire ventilation. As rail transit systems expand to meet increased ridership, it is often necessary to bore new tunnels for alignments in congested areas where surface rights-of-way are lacking. Such proposed alignments can pose significant challenges for transit agencies, as they contend with various tunneling problems."

Jan 1, 2016

By M. A. Kaufman

In this paper I will attempt to present an up to date review of the type of exploration' that has previously been carried out in Alaska, discuss some of the more significant past producers and recent discoveries, and suggest some approaches to future exploration. Hopefully this information may be of some use to those parties tempting to evaluate Alaska's non ferrous, non placer, metal potential or contemplating initiation of exploration in the state. II. SUMMARY AND CONCLUSIONS Past production of non ferrous metals from lode deposits in Alaska has been meager considering the size of the state. Since there have been no major lode mines operative in Alaska since World War II, and since logistical conditions vary throughout the state, it is not possible to generalize with respect to mining costs in Alaska as compared to those in other areas. There seems to be little question, however, that a major deposit situated in a reasonably favorable location' could be profitably operating at present. Host of the known metal prospects in Alaska were discovered by early gold prospectors prior to World War I. From World War I through World War II exploration consisted chiefly of surface prospecting by prospectors on a diminished scale, as compared to the early gold rush days, drilling of some prospects by the U.S.B.M,, and occasional mine or prospect evaluations by mining companies. From the end of World War II to the present time, there has been a generally steady increase in exploration by mining companies consisting chiefly of prospect and district evaluations, large scale aerial reconnaissance programs in search of color anomalies, and regional drainage geochemical surveys. The post World War II increase in mining company exploration has not been matched by an increase in conventional surface prospecting.

Jan 1, 1972

"INTRODUCTION Foam, unless intentionally created, in any industrial process presents operational problems, or at a minimum, is a nuisance. Some foam problems are unique to a given industry and others are common across many industries. A few problems foam presents to any particular industry are: (a) Poor Housekeeping, (b) Environmental impact, (c) Safety Hazards, (d) Slower Production Rates and, (e) Reduced quality of the end product. Defoamers address these issues. Sadly, the assumption in most industries is all defoamers are alike. In reality, a lot of chemistry is involved in the manufacture of even the simplest defoamer sold today and rarely are any two defoamers “just alike”. Today’s defoamers can include polymer chemistry, fatty esters, alkoxylated alcohols, silicone chemistry, silicone surfactants, ethoxylated and propoxylated block polymers, and a tremendous amount of emulsion chemistry just to name a few. This paper will discuss the various types of defoamers, defoaming mechanisms, the advantages and disadvantages of defoamer selections, and how to choose the proper defoamer for your application. Before a discussion of defoamer can be brought about, foam generation and composition must be discussed. WHAT IS FOAM? Foam is a colloidal suspension of a gas dispersed in a liquid. Most often foam consists of air dispersed in water. If a stream of air is introduced into a liquid, the bubbles produced assume a spherical shape. As the density of the bubble is less than the liquid the bubble rises. When the individual bubbles reach and pass through a surfactant free liquid they collapse. Air from the bubble dissipates and the liquid previously surrounding the bubble flows back.It should be noted a pure liquid will not foam. In the case of air dispersed in water a surfactant is necessary to make the water support a stable foam. A surfactant is a term used to describe a surface active agent; a compound with a hydrophilic end and a hydrophobic end on the same molecule."

Jan 1, 2016

By Christopher Mark

Area wide pillar failures, or “squeezes,” were once fairly common in underground coal mines. While rare today, they do occur. This paper describes seven case histories that were investigated by MSHA Technical Support. They occurred across the range of US coalfields, in both longwall and room-and-pillar mines, and involved development mining, pillar recovery, longwall panel extraction, and multiple seam interactions. Significant lessons from each are discussed.

Jun 25, 2024

By H. B. Oblad

Coal/pyrite fines were froth floated in a laboratory cell to examine the rate of pyrite recovery during conventional coal flotation. The effects of collector, particle size and carbon to total sulfur ratio on the kinetics of recovery were investigated. These data coupled with microscopic examination suggest that miniscule amounts of coal that remain attached to the pyrite surface affect the rate of flotation of pyrite.

Jan 1, 1985

By B. Akwasi Osei

The lack of metrics to assess clamshell formation dredgeability limits the ability of engineers to predict the dredgeability of compact material and increases the risks associated with clamshell selection. Research is needed to develop metrics for predicting clamshell dredgeability. The objective of this paper is to evaluate possible metrics to predict the dredgeability of compact aggregates by hydraulically actuated clamshell dredges. Data on cylinder pressures and displacements, motor current, bucket tilt and cycle time (CT) were collected from a dredge. Work done and motor energy, potential metrics, were computed and their suitability in predicting dredgeability evaluated. Data analysis shows that; there is no correlation between tilt angle and work done or motor energy; a low correlation between CT and work done, and a strong correlation between CT and motor energy. Work done is a better measure of formation dredgeability, than motor energy, as it shows lower variability. However, in difficult digging conditions, work done alone does not accurately predict dredgeability. This work shows that, it is feasible to use cylinder pressures and motor signals data to predict dredgeability.

Jan 1, 2010

By Oscar M. Wicken

Iran was a lodestone for the attention of industrial countries and companies wanting to share in its industrial development during the last two decades and particularly after 1972. Prior to 1972, most industrial projects in the private sector were on a relatively small scale and could be carried out in reasonably orderly fashion in spite of limitations of a primitive infrastructure and meager indigenous supply of managerial and technical skills. People with these skills could be found but not in abundance, and many of them were total¬ly engaged in various government ministries and projects. Thus it was that nearly all private sector industries, even long-established ones, required one or more foreigners to give guidance. A barite mine and processing facility was brought on line by Dresser Industries in 1960 without serious operational problems. A few expatriate experts were able to select and train a stable group of staff and production people and establish sound management principles for continued growth. The huge and increasing oil revenues after 1973 gave superficial credence to ideas of the Iranian government that the country could easily finance the jump into the industrial 20th century. All necessary skills and equipment not available in Iran would be imported, and intensive training programs would prepare Iranians for operating the new facilities. Large projects for steel production, copper production, oil refining, petrochemical production, cement production, and others were started or expanded. These are basic industries that consume substantial quantities of refractories. Studies made in 1972 indicated that the existing industries plus expanded and new projects scheduled to come into production would lead to a market sufficiently large to justify a refractory producing plant. Concurrent studies of raw material sources showed that clay, the largest tonnage item, would be locally available; the other raw materials would be imported. Iran Refractories Company (IREFCO) was founded in 1973 and started production in 1976.

Jan 1, 1981

By R. Wu, R. Howell, J. Dase

Turquoise Ridge is an underground gold mine located in the Potosi Mining District, approximately 64 km northeast of Winnemucca, Nevada. Turquoise Ridge Underground is accessed via two shafts and a system of internal ramps and utilizes underhand drift and fill mining methods with cemented rockfill. The mine also employs mechanical mining as well as sill benching as mining methods. Ground conditions at Turquoise Ridge Underground are poor, and the Rock Mass Rating (RMR) may be less than 20, or very poor, in ore headings. Current production rate is 2,700 tonnes of ore per day. Key challenges in increasing production levels and reducing costs are the development of sufficient stoping areas and the transition from top-cut development to undercut stoping. Completion of the infrastructure development in the North Zone is necessary to achieve and optimize higher production levels. The #3 Shaft project is well underway and is expected to be commissioned in mid. 2022. The shaft will drastically decrease the haulage requirements in the North Zone

Mar 2, 2022