Search Documents

By J. van Oldenborgh

The world market for bunkers represents some 140 MT (1980) of marine fuel oil and distillates. This is equivalent to 23CMT of coal, a potential market for steam coal larger than the total seaborne trade of steam and metallurgical coal today, and an obvious area which could contribute savings in world oil consumption. Oil bunkers are lifted fairly evenly throughout the world, the main supplying regions being Western Europe, the Middle East, North and Central America and Japan (Figure 1). Not surprisingly, the main customers are the tankers representing about 50 percent of the world market - (95 percent of the Middle East Market) - dry bulkers represent some 30 percent and general cargo ships the rest.

Jan 1, 1982

By Kadri Dagdelen

The classification of selective mining units (SMU) and the assignment of grades to those classified SMU are very important in open pit mining, especially for precious metal mining. When the classification is done, the true values of the SMU grades are unknown. These unknown SMU grades are mostly estimated analyzing the geologic data and blast hole assays. To classify the SMU's based on the estimate of SMU grade, without considering uncertainty associated with unknown SMU grade, yields incorrect decision in sending material to appropriate destination. In this paper, a method is developed to classify SMU's considering the uncertainty associated with unknown SMU grades. By using this method, traditional estimate of SMU grade is replaced with conditional probability distribution of SMU grade. The decisions about the destination of a given SMU are performed by minimizing the loss due to misclassification. Also, the asymmetric loss function by penalizing the overestimation and the underestimation unequally is used in assigning grades to classified SMU's. A case study is carried out to apply the traditional ore control techniques and proposed method in classification of SMU's and the assignment of the grades in a hypothetical gold mine.

Jan 1, 1999

Current scrubber capacities vary from 1.89 to 4.72 m3/s (4,000 to 10,000 cfm), and there is interest in using scrubbers with capacities up to 6.61 m3/s (14,000 cfm). This paper describes research to compare the effectiveness of blowing and exhausting face ventilation systems using high-capacity scrubbers with flows up to 6.61 m3/s. Tests were conducted in a surface ventilation gallery with exhaust and blowing systems operating under similar conditions. The mining machine was equipped with a machine-mounted scrubber. Methane gas was released at constant flow at the mining face and measured at several face locations. Effectiveness of exhausting and blowing systems was compared by determining average face methane concentrations. For each operating condition tested, blowing ventilation was more effective than exhausting for controlling face methane levels. Raising scrubber flow to 6.61 m3/s reduced methane levels for both blowing and exhausting systems.

Jan 1, 1996

By Nathaniel Arbiter, Robert R. Beebe

The U.S. mining industry - once world dominant and largely independent of foreign sources for most major commodities - has today lost this position, with little likelihood of regaining it. But even though Business foretold The Death of Mining four years ago, the current outlook is less pessimistic because of drastic restructuring of the industry; a major reduction in its labor force, with resulting large increases in productivity; and introduction of improved technology. In the face of this clearly changed climate for domestic mining, it is important to examine the role of the development and research establishment in the industry's future, which raises a complex set of questions: 1. Where and to what extent can new technology assist in the continued survival of the industry ? 2. What is the past record of the research establishment in developing new technology; and what is the industry's record in supporting and adopting it ? 3. In the light of these records, and of the drastic cuts in both research staffs and expenditures, what areas should be the most important targets for new technology? New Technology vs. Old A1 though mineral processing's origins can be traced back through five or six millennia, its modern structure is about 200 years old.

Jan 1, 1989

By J. A. Harrison

Most coal being used in the United States has been subjected to one or' more processes of coal preparation. The physical and chemical characteristics of a coal have a marked influence on the ultimate uses that coal may have. The selection of the proper preparation processes may similarly be important in producing the best practical coal product for any particular use. The physical composition and distribution of physical constituents in the coal will partially determine the efficiency of the preparation process chosen and conversely distribution and concentration of coal macerals will, to a degree, be controlled by the preparation process. A number of preparation processes have been evaluated to determine this interrelation. If a coal having' certain specifications is desired, these evaluations trill assist in providing information needed for the production of this coal.

Jan 1, 1962

By B. R. Arvidson

Sharper separation and improved control of the top size increases the fine particle product yield. As the milling circuit recycle stream is reduced, the overall capacity is increased. In some cases, a doubling of throughput is realized, although 25 to 30% increase is more typical. Alternatively, the energy demand may be reduced, although the best economic improvement results from higher capacity. A comparison with a high-pressure roller mill circuit shows that an optimized ball mill circuit retrofitted with the new air classifier has lower energy consumption. The new air classifier features low energy demand and substantially lower maintenance compared to similar equipment. Design and operation of this recently patented classifier are discussed. Several industrial installations will be described.

Jan 1, 1999

By A. Röttger, W. Theisen, J. Küpferle, M. Alber

"Wear of TBM tools significantly affects tunneling advance rates. Wear-prediction models are based (amongst others) on the abrasivity of the present geology, which is determined via laboratory tests. To evaluate the results from such tests in context, this work considers the tribological system TBM tool from a materials technology perspective. In so doing, the microstructures of different application-oriented materials are presented and discussed in terms of their wear behavior and wear resistance. The significant influence of tool materials on the abrasivity of the geology and thus wear prediction models has already be identified. LCPC, Cerchar and nano-scratch experiments have been performed as confirmation. Material-dependent wear mechanisms and their correlation in terms of tunneling have shown that it is mandatory to consider the complete tribological system to estimate the wear of TBM tools. 1 INTRODUCTION Mechanized tunneling is vital to ensure necessary infrastructure development in megacities like Tokyo (Bay Tunnel), Istanbul (Eurasia Tunnel) and Mexico City (Tunnel Emisor Oriente). The use of Tunnel Boring Machines (TBMs) has been established for many years. In contrast to other methods such as boring and blasting or excavation using dredgers, tunneling with TBMs allows simultaneous excavation and removal of both the mineral and tunnel lining by tubbing segments or shotcrete. This makes tunneling more efficient, allowing for faster development of the tunnel in both hard rock and soil [1]. When budgeting such tunneling projects, precise planning and coordination in terms of tunneling technique choice (e.g. EPB or Slurry-shield), the relevant geology, and the associated penetration rates and tool wear are required. In particular, wear to TBM tools has a significant impact on tunneling progress. Due to wear, tools become dulled or lose their functionality because of brittle material behavior, thus reducing penetration rates and therefore tunneling efficiency [1]. As a result, additional tool changes are necessary, leading to higher overall costs due to down times and maintenance costs. Therefore, there is strong interest in a reliable and precise wear prediction model for TBMs. As already mentioned, the geology and associated wear of the tunneling tools define the maintenance times."

Jan 1, 2016

By Charles Banks Belt

In 1925, Niggli (1925, pp, 1-69), formulated a physico-chemical, explanation for the origin of hydrothermal ore deposits, from a concept that had appeared earlier in the literature in the writings of Von Groddeck, Stelzner, Beck, de Launay, Kemp, and Lindgren. Niggli proposed that pressure at depth could force volatiles from deep-seated magmas. The volatiles would In turn form pegmatites and then ore deposits as the fluids cooled. This is one view of a general theory of ore genesis that gained secondancy for years among such prominent geologists as Fenner (1926, p, 697) and Emmons (1936, pp. 29-70). It was, proposed that ore deposits were precipitated from solutions or fluids that had escaped or been separated from a deep-seated magma by means of liquid immiscibility or crystallization or gas transfer. This theory is based on the presence of igneous rocks close in space and age to hydrothermal ore deposits in many mining districts of the world. As is well known, there are many ore deposits apparently of hydrothermal origin that are neither spatially nor chronologically related to igneous rocks, In still other localities where there are no hydrothermal ore deposits, igneous rocks occur that are similar in composition to those in mining districts. In view of such facts, the applicability of the Niggli theory to all hydrothermal ore deposits may well be questioned. The chief purpose of this paper is to test the Niggli theory by studying the primary petrology, hydrothermal alteration, and distribution of copper and zinc in silicic igneous plutons supposedly genetically related (in the Niggli sense) to nearby hydrothermal ore deposits, Silicic Tertiary plutons in three New Mexico mining districts were chosen, the Hanover-Fierro intrusive at Hanover and Fierro, the Granite Mountain pluton at Magdalena, and the four outliers of the Lordsburg stock at Lordsburg. First, it had to be established whether the observed plutons were or were not the source of the adjacent ore deposits. This was done by studying the relation between the copper or zinc distribution-and the primary or secondary features in the plutons studied, and the time relations between instrusion and ore deposition. Primary igneous features of a pluton are defined as the minerals, texture, shape, and character of the pluton which were formed prior to the complete solidification of the rock, secondary features include all changes that took place in a pluton after solidification. They are identified by their cross cutting nature or as replacing primary minerals, Under the Niggli concept, it is proved that the ore ions did not originate from the parts of the pluton now visible as immediately adjacent to the ore deposits; it must then be established, if possible', that the ore ions were separated from deeper parts of the intrusive, Some idea as to whether the copper or zinc ions originated from a related magma at depth may be gained by a comparison between the primary (that is, pre-alteration) zinc and copper abundances found in ore localizing intrusive studied and the average abundances for copper and zinc in silicic igneous rocks most recently given in the literature. Finally, the relation between ore deposition and hydrothermal alteration was studied on a regional as well as on a local scale.

Jan 1, 1958

The Bureau of Mines has studied 260 underground coal mine fires which occurred from 1970 through 1989. Every fire had the capacity to be hazardous to life and property, however upon closer examination some were found to be inherently more dangerous than others. Our research involved reviewing and recording specific information contained in published Mine Safety and Health Administration fire accident reports. The objective was to determine if degrees of hazard relative to fire source or location could be construed from information contained in the reports. We specifically looked at the propensity for fires to cause injuries and fatalities as well as the need to seal the area in order to extinguish the fire. Relative to all underground locations, this review found that fires occurring in main haulage-ways were most likely to cause injuries and fatalities as well as require sealing of at least the immediate area to extinguish.

Jan 1, 1993

By J. Richard Lucas

Today, the future of the coal industry is extremely bright because coal can be produced at a cost which makes it competitive with other energy sources. However, the industry has been forewarned that further cost reductions must be made if it expects to remain a serious contender in the growing energy market. Surface as well as underground operations must be improved. The very same elements which affected production a. few years ago still exist today and will continue to be present in the future. Improvement's in production mining equipment, mining methods, and auxiliary equipment have resulted in reduced costs over the past few years. Efforts must be continued toward further reducing costs in areas which have been improved previously, and new areas should be investigated for possible improvements. Therefore, new techniques must be developed which will enable the industry to augment its current efforts in reducing the cost of mining. The logical place to begin evaluating the factors affecting production and cost is in the immediate face area where a substantial part of the total cost of mining is incurred. The coal industry stands to gain much through the development of new techniques for analyzing the numerous variables affecting production and by establishing methods for eliminating or minimizing the adverse effect of those variables which can be controlled. Intuition and trial-and-error methods have been the standard means used to resolve many of the factors which influence production. As a result, many elements are overlooked or ignored because their effect on production is not pronounced and cannot be readily resolved. The need for a method of analyzing such factors was recognized by the Office of Coal Research. Therefore, in April 1962, under OCR sponsorship, a. research project was initiated at Virginia Polytechnic Institute (VPI). The objective of the project was to identify the factors which influence mining costs in the immediate production area, and to develop methods and techniques which will enable the coal operator to minimize production costs. The objective of the research at VPI has been successful, and techniques have been developed for establishing quantitative facts concerning the interrelationships of production activities.

Jan 1, 1965

By J. M. Duke

Significant resources grading less than about 1 % nickel occur in magmatic sulfide deposits of two types. In the Mt. Keith type, extensive zones of disseminated nickel sulfides occur in the central portions of certain synvolcanic dunite-peridotite sills of komatiitic affinity in Archean greens tone terranes. In the Duluth type, disseminated copper-nickel sulfides occur near the basal margins of intrusions of flood basaltic affinity associated with intracontinental rifting. In both types, the parent magmas became saturated with sulfide following the onset of fractional crystallization and the separation of the immiscible sulfide melt was accompanied by the precipitation of a relatively large proportion of silicates. The abundant silicate crystals impeded the coalescense and accumulation of the sulfide droplets with the resulting formation of large but low grade deposits.

Jan 1, 1982

By V. E. Housman

EPA's Mining Waste Section within the Office of Solid Waste is continuing to collect and analyze information on mining waste management practices. Starting in 1991, the Mining Waste Section has continued to conduct site visits and prepare case study reports on the waste generation and management practices of operating mines. In choosing sites to study, a reasonable attempt was made to provide diversity in mining commodity types, geographic regions, geology, climate, and environment. To date, EPA has visited the following mines: Asarco Troy (copper) in Montana, Newmont Rain in Nevada (gold), Cyprus Thompson Creek (molybdenum) in Idaho, LTV Steel (iron) in Minnesota, Phelps Dodge Morenci (copper) in Arizona, Doe Run Fletcher (lead) in Missouri, Brewer (gold) in South Carolina, IMC Four Corners (phosphate) .in Florida, Pennzoil Culberson (sulfur) in Texas, Nerco Cripple Creek (gold) in Colorado, Copper Range White Pine (copper) in Michigan, Magma San Manuel (copper) in Arizona, Colosseum (gold) in California, and several gold placer mines in Alaska, including the Valdez Creek Mine. EPA has prepared a case study report on each facility. The mine operators were provided an opportunity to comment on their respective site visit report and their comments have been included in' each respective report. These site visit reports have in turn been incorporated into technical resource documents which provide a detailed description of each mining sector. EPA is currently reviewing the technical resource documents and plans to release the documents in the Spring of 1994.

Jan 1, 1994

By Gordon R. Haworth

During the past ten years we have experienced a period of rapidly-changing ground rules for the mining industry. Domestically we have had to contend with numerous new regulations controlling the impact of mining-related activities on the environment. However, for the purposes of this presentation we will assume that in the United States, after a certain amount of compromise on all sides, the industry will be able to work within the framework of the new regulations, and therefore we will concentrate on offshore developments. Due to the limitations in time and scope, this paper will be directed primarily toward the metal mining industry. We contend that the U.S.-headquartered mining company should remain active, and even expand its interests in foreign countries in the future. This is our feeling in spite of recent setbacks and the low return on investment experienced in recent years by some of the metal mining companies in their foreign operations.

Jan 1, 1975

The Australian states of New South Wales (NSW) and Queensland, because of their endowment of black coal resources, dominate the production and export statistics for Australian coal. NSW produced 86 million tonnes of saleable coal in 1994, representing a doubling of output since 1980, or a growth of 5% per annum. Asian demand for thermal and coking coal has, of course, driven this growth in NSW. This high Asian demand is forecast to continue and NSW will seek to secure its share. This paper focuses on some of the issues facing NSW in the future, and in particular, examines some of the major new and proposed mining projects.

Jan 1, 1997

By J. Grubb

"The undertakings described in the paper titled “Study on correlation of quantified coal rank with self-heating temperature” by Wang and Luo in the November 2015 issue of Mining Engineering (Wang and Luo, 2015) are mathematically sustainable and an acceptable extension of work performed by Smith and Lazzara (1987) for the U.S. Bureau of Mines. The paper is not an accurate explanation of the currently accepted leading practice for determining the propensity of a coal seam for spontaneous combustion. The paper could lead a practitioner to an oversimplified conclusion on how to determine the propensity of a coal seam to spontaneously combust.The spontaneous combustion of coal is a complex and not fully understood reaction. What is understood is that many more factors other than selfheating temperature (SHT) and coal rank are required to sufficiently evaluate the risk of spontaneous combustion in a particular coal seam. A superficial assessment can lead to an improper response to the risk. Some statements on the next steps through an appropriate literature search would have made the authors’ conclusions more credible.The SponCom 2.0 software, updated by the National Institute for Occupational Health and Safety (NIOSH) in 2011, provides a path for evaluating the susceptibility of a coal seam to spontaneous combustion. In addition to proximate and ultimate analyses to establish coal rank, and therefore an estimate of SHT, the program includes the history of heatings, friability, seam thickness, overburden thickness, rider seam presence, pyrite presence, face and butt cleat densities, geothermal source presence and other geological features in the assessment. Mining conditions including floor heave, rib sloughage and rate of advance are also assessed to conclude a propensity for spontaneous combustion."

Jun 1, 2016

By T. S. Govindan

The first step in energy conservation in any industrial plant involves implementing many of the day-to-day "house-keeping" items such as fixing leaks, turning out lights, etc. When this step has been accomplished, additional opportunities require a detailed analysis of the energy systems, evaluation of risks and costs, and assignment of priorities. Examples of conservation schemes drawn from the experience of Du pont's Energy Management Consulting Services will be discussed. The utility of heat balances for kilns and dryers in minerals processing will be outlined. The inputs needed from Management for the success of conservation efforts will be discussed.

Jan 1, 1978

By F. W. Schweitzer

The trend toward development of large low grade ore bodies has accelerated in recent years. It has been estimated within the copper industry that "porphyry" type deposits will provide the bulk of copper production during the next 30 years. It is further estimated that in these deposits the average ore grade by the year 2000 will be 0.25% copper (1). Many of the new porphyry copper discoveries are of such extremely low grade that they are particularly sensitive to small fluctuations in cost variables and copper prices. Because haulage constitutes a major item of surface mining expense, the capability to transport large tonnages of material at increasingly lower unit costs is vital to the profitable operation of many of these mines. High capacity conveyor belts appear to have considerable promise in this area. The heaviest use of high tonnage conveyors has been in the brown coal industry in Germany. In the past 20 years several such installations have proven successful. In addition to the German installations, several other successful systems have been put into operation. Some examples are: The Oroville Dam project in the United States; the tar sand operation in Northwest Canada; the pre-mine stripping and mining of the Twin Buttes Mine in the United States; the Kursk Magnetite 'dine in the U.S.S.R.; and the Nchanga Copper Mine in Zambia. Most of the systems mentioned are handling alluvial material consisting mainly of fines. The noteworthy point regarding these installations is their high continuous capacity. One of the largest lignite mines in the world is at Fortuna, Germany, where over 15,700 tons (15,250mt) per hour of overburden is transported on an 87 inch (221cm) wide belt running, at over 1000 feet (305m) per minute.(2). Another example is a 20,000 ton (18,150mt) per hour system for loading iron ore into barges on the Great Lakes (3).

Jan 1, 1976

By R. O. Y. Breese

Perlite is a hydrated acid volcanic glass that has been derived from the alteration of obsidians through incorporation of water into the silica structure. It is distinguished from other members of the water-bearing natural glass family by total water content, characteristic fracture and luster. The distribution of major occurrences worldwide is associated with silicic Tertiary through early-mid Quaternary volcanics related to plate movement. The No Agua dome and flow complex is one of the most highly studied perlite occurrences in the world. It clearly exhibits lithologic and textural zonations that reflect simple cooling history. Similar features are commonly observed within other perlitized, extrusive glass selvages. This paper briefly discusses current thought regarding geologic occurrence, the hydration process and the modes of origin with special emphasis on No Agua.

Jan 1, 1985

By I. K. Gilmore

Texasgulf Inc. currently operates an open pit phosphate mine in the central coastal plain of North Carolina. The area of phosphate deposition lies within the Aurora Phosphate district which consists of an embayment which is in the center of the Neogene phosphate deposition. A variety of solid and liquid fertilizer products are produced at the Texasgulf complex. One of these products is known as North Carolina Natural Phosphate (NCNP). New potential for use of unacidulated natural phosphate, now exists in regions with acid soils due to the discovery of the findings from recent research, cost advantages, and moves to reduce chemical inputs.

Jan 1, 1995

By Richard Giffen, Boris CARO VARGAS, Terrence Carroll

"This paper takes an in-depth look at the $72 million design-build Norris Cut project, which includes the replacement of an existing 54-inch waste water sewer main to Fisher Island under the Norris Cut Channel. Tunneling through one of the country’s most unpredictable geologies created unique challenges in both the design and construction phases of the project. The paper presents the geotechnical and structural design considerations for the 100-foot deep secant piled TBM launch shaft in the highly permeable Fort Thompson formation limestone and sands. The structural design effort also included the design of the tremie slab, thrust wall and design of the largely unreinforced launch shaft to resist asymmetric loading from partial ground freezing. The retrieval shaft was designed as a deep soil mixed shaft and is thought to be the deepest soil-mixed shaft in Miami. From a construction perspective, this paper discusses the unique challenges of building two shafts with two different techniques and will compare some of the constructability aspects, costs and equipment schedule-considerations related to the use of two separate techniques. INTRODUCTION Nicholson Construction Company (NCC) was awarded a $72.1 million Design-Build contract to replace an existing force main from the Virginia Key Central District Wastewater Treatment Plant (CDWWTP) under the Norris Cut Channel to Fisher Island. The location of the project is shown in Figure 1. The project involves replacing an existing 54-inch diameter pre-stressed concrete sewer force main with a 60-inch diameter fiberglass force main. Arup USA, Inc. (Arup) is the lead designer for Nicholson on this design-build project. Arup is providing design services for the TBM launch and retrieval shafts, segmental tunnel lining, the fiberglass pipe, and the horizontal directional drill component. Miami-Dade Water and Sewer Department currently owns and operates the existing 54-inch sanitary force main that transmits sewage collected from Miami Beach and Fisher Island to the CDWWTP for treatment and disposal. The existing force main was subject to a condition assessment in December 2011 which revealed structural deficiencies in the pre-stressed concrete pipeline."

Jan 1, 2016