Search Documents

By F. Mielli

Over the last three years there has been an increase in mining congress and conferences focusing on water management. Water in mining is a key concern for mine managers and operations, and we are now seeing this operational dilemma escalated to the level it deserves. According to Frost & Sullivan research, mining water and wastewater treatment and its related technologies will be a U$3.6 Billion global market in 2016, which translates the importance of this issue. Looking at the current mining trends, some factors increased the importance of water in mining operations, including: ? Future mining investments will be located in geographical locations where water is scarce (water stressed areas) ? A decline in grade will increase the intensity of mineral processes and therefore increase the use of the water ? Increased sustainability and regulations will extend the control/monitoring of water during the entire mine life cycle representation of the mine water flow system. A water balance has several benefits/objectives in a mine operation: ? Mine planning/simulation of mining scenarios/climate change Production optimization ? Minimizing strategic and operational risks ? Social license to operate ? Water-smart mine planning ? Target: water neutral mines ? Benchmarking within and between sites ? Sharing knowledge/technology transfer ? Reporting/communications ? Permitting/Compliance

Feb 23, 2014

In cold regions rinsing of spent cyanide leach heaps is stopped during winter and is resumed again after snow melts. The effect of this idle time on the overall cyanide removal process was studied in this work. Samples were collected for rinsing tests from one heap at the Ryan Lode Mine of Citigold Alaska, Inc., near Fairbanks. The material was tested for cyanide removal a large column, 1.22 m high by 20 cm square, and in a small column, 1.22 m high by 10 cm in diameter. The rinse water was analyzed at regular intervals to determine the rate of cyanide removal from the solids. It was found that diffusion plays a major role in the removal of cyanide from the ore particles. Calculations showed that the insulating effect of the snow cover on the heap provides an excellent moderates the interior temperature of the heap, and would be expected to help the progress of the diffusion reaction during winter. The result expected result wil1 be higher cyanide values reporting to the rinse water after snow-melt.

Jan 1, 1993

By Cody Edwards, Ross Webb

5 miles of soft ground tunnel excavation for the SAWS W‑6 project finished months early despite difficult conditions. Success was achieved using TBMs and other equipment built long before most of the crew was even born. The old school means and methods easily adapted to the conditions encountered and were key to the project’s success. Unfortunately, an industry trend is to specify more “advanced” equipment which can sacrifice adaptability or productivity for a perceived reduction in risk. This case history discusses when traditional methods may be the best option.

Dec 1, 2022

By B. A. Kuyper

The Cove gold-silver deposit is located 50 km southwest of Battle Mountain, Nevada and 1.5 km northeast of the McCoy Mine. Total proven and probable reserves are 48.7 Mt (53.7 Mst) with an average grade of 1.85 g/t (0.054 oz/st) Au and 87.1 g/t (2.54 oz/st) Ag. Mineralization is hosted by Triassic carbonate and siliciclastic rocks in two separate orebodies. Oxide ore consists of disseminated gold and silver in clay-altered, manganese-flooded limestone. Sulfide ore is dominated by pyrite-sphalerite-galena veins in siliciclastic rocks and sandy dolomite. Gold and silver occur in the native state, associated with the base metal sulfides. Mineralization is interpreted to be the distal expression of a porphyry system. The McCoy gold (copper) deposit is interpreted to be the proximal expression of the same system.

Jan 1, 1991

By James M. Krese

The West Kentucky Division of Island Creek Coal Company, which is a wholly owned subsidiary of Occidental Petroleum Corporation, operates the new Hamilton Mine. It is located six miles West of Morganfield, Kentucky, in the Northwest section of Union County, adjacent to the Ohio River in Lock 50. On July 15, 1968, a unique new coal conveying system was put in operation. This system consists of eight conveyor units carrying coal from the bottom of the mine slope ultimately to barges on the Ohio River. It is over two miles in length and has a total of 3175 connected horsepower. The river loading conveyor is the longest 72" wide conveyor in operation in this country.

Jan 1, 1969

By MARK J. VANARELLI

Estimating groundwater inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies for estimating steady-state groundwater inflows into deep rock tunnels. The case studies included the Chattahoochee and Nancy Creek tunnels. In this paper, statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations. A semi-empirical procedure was utilized for estimating groundwater inflows into these deep rock tunnels. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels which exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semi-empirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Packer test data plotted in histograms were observed in all cases to be log-normally distributed for the radial flow condition. Modeling using Monte Carlo simulations was observed to be an effective tool for removing irregularities in the distribution of the data and incorporating high-end permeability data to derive reasonable groundwater inflow estimates.

Jun 13, 2021

By Frederick S. Fisher

Three spatially separate porphyry copper/molybdenum deposits are associated with the Tertiary Needle Creek igneous center in the southern Absaroka Mountains, Wyoming. In all three deposits a central zone containing disseminated copper and molybdenum is surrounded by a halo of small, discontinuous base and precious metal veins. Propylitically and phyllically altered rocks are common in all three mineralized areas, and potassically altered rocks are locally present. Fission- track age data from apatite and zircon indicate that mineralization occurred about 32-40 m.y. ago. Limited data suggest that the lead isotopes are nonradiogenic, similar to porphyry copper deposits elsewhere in the western United States. The complex igneous history of the Needle Creek center has involved several periods of intrusive and probably extrusive activity. lntrusive rocks are calc-alkalic and include andesite, granodiorite, diorite, quartz monzonite, dacite, and rhyodacite. Stocks (1-30 kmz in exposed area), radial dike swarms, and sills make up the presently exposed plutonic masses and constitute lower-level vent fillings in an old stratovolcano. The Needle Creek igneous center is located approximately midway along a northwest-trending belt of intrusive rocks extending more than 100 km along the central axis of the Absaroka volcanic field. The igneous and mineralized centers within this belt were probably localized at the intersections of northwest- trending Laramide and possibly Tertiary fracture systems and earlier northeast-trending Precambrian structures in the underlying basement rocks.

Jan 1, 2013

By D. C. Yang

A packed column jig has been developed for sharp separation of fine particles--150 down to 1 micron--having different densities. The packed jig is a column filled with corrugated packing. A slurry of mixed particles is fed into the middle of the column. Water enters near the bottom of the column as both a steady state and a pulsating flow. The pulsating water sets up a jigging action that interacts with the packing causing the dense particles to sink and exit the bottom of the jig and the lighter particles to rise and exit the top of the packed jig. The result is a sharp, environmentally friendly, gravity separation machine with low operating costs. Grades and recoveries of iron ore exceed that of known devices. Grades as high as 95 percent purity with concomitantly high recoveries are common for iron ore concentration. Low silica, sulfur and phosphate are common. This paper is the first to unveil the packed column jig technology in detail and presents its physical model with performance data. The purification of iron ores and coal is the paper's focus.

Jan 1, 1997

By Allan M. Harvey

Asbestos production in the United States is no match for the vast operations of Canada and the U.S.S.R. The majority of U.S. production is limited to the states of Vermont, California and Arizona, and the type of asbestos is limited to the variety of serpentine known as chrysotile. What little production of other varieties of asbestos such as tremolite and anthophyllite that has occurred over the past 100 years since asbestos became a useful commodity is of practically no significance. However, new developments in the field of environmental and occupational health hazards has startled the mining industry in this country and has already given a few particular companies reason to be concerned about the profitability and probability of their continued operation in the business of mineral processing. At the heart of these developments is the question and controversy over just what constitutes asbestos and what exactly is the definition of a fiber. To the mineralogist or, in fact, to practically anyone engaged in the process of mining and separating minerals there is little or no question about asbestos. It is not a distinct mineral but rather a commercial product serving specific applications for which a number of fibrous mineral types can qualify. To the hygienist pr health authority this definition is too general. They demand something they can detect, measure and control. To suit their purposes and simplify their task of detection, they have labelled the minerals chrysotile, crocidolite, amosite, tremolite, anthoph-yllite and actinolite as asbestos, and any particle of these minerals with an aspect ratio of 3:1 as an asbestos fiber. It does not

Jan 1, 1976

By H. C. Lautenschlaeger

Let's start with a bit of History. Before the advent of woven wire screen cloth or perforated plate as we know it today, screens or sieves, as they were called, were probably made by the Greeks or Romans around the year 150 B.C. Coarse openings were made from bamboo or other woven reeds or with holes punched in leather hides, while fine openings may have been made using hair from the long tails of horses woven with small openings. The first metallic woven wire screens were probably produced by the Germans in the 15th Century. All of these screening devices were, of course, hand operated. The first records of mechanically driven shaking screens are found in "John Smeathon's Diary of His Journey to the Low-Country" in 1775. He was the English Civil Engineer who built the famous Eddystone Light House and discovered the formula for making hydraulic cements. He described a screen the Dutch were using as a wooden frame on which woven wire was mounted. This box was inclined at an angle and hinged on the lower end. The upper or feed end was equipped with a pulley so they could raise it up, say 5" or 6", and then let it drop abruptly onto a sill or stop plate, thus jarring the material deposited on the woven wire through the openings. Material that was passed over the deck was scooped up and redeposited on the woven wire for rescreening. This was an early form of what is today known as a recirculating load.

Jan 1, 1983

By Mahiyar Nasarwanji, Jonathan K. Hrica, Jonisha P. Pollard, Lydia M. Kocher, Brianna M. Eiter

Within the metal/nonmetal mining sector, fall-related incidents account for a large proportion of fatal and nonfatal injuries that occur in mining in the United States. However, the events and contributing factors leading up to these incidents have not been fully investigated. To help provide a clearer picture of these factors, an analysis of imminent danger orders issued by the U.S. Mine Safety and Health Administration (MSHA) from 2010 through 2017 at both surface and underground metal/nonmetal mine sites revealed that most orders are associated with fall risks. Of these cases, 84 percent involved the workers not using fall protection, fall protection not being provided or the improper use of fall protection. Fall risks for workers most frequently occurred when standing on mobile equipment, performing maintenance and repairs on plant equipment or working near highwalls. In most cases, a single, basic, corrective action — such as using fall protection — would have allowed workers to perform the task safely. Overall, these findings suggest that a systematic approach is needed to identify, eliminate and prevent imminent danger situations. Furthermore, to protect mineworkers from falls from height, frequently performed tasks requiring fall protection should be redesigned to eliminate the reliance on personal fall protection.

By G. L. Alston

Rigid urethane foam can be used effectively for improving mine air conditioning systems by reducing heat and moisture transfer from mine rock to ventilating air and from mine rock to ventilation ducts, for erecting mine ventilation stoppings and overcasts, for sealings around door frames and bulkheads to prevent air leakage, for preventing spalling and sloughing of roof and rib and for erecting fire-resistant powder magazines and transformer or compression stations. Rigid urethane foam is a tough, cellular material, made by nixing diisocyanate and polyether polyol resin in accurate proportions through an applicator system, then the two chemicals react, the mixture expands thirty times its original volume with 85 to 95 percent closed cells. Within seconds, the mixture solidifies and takes a preset which will adhere to overhead or vertical surfaces. It will adhere to brattice cloth, steel, wood, concrete and rock, Excessive wetness will reduce the adherence, but in such cases adherence can be improved by preliminary application of an absorbent dust such as cement.

Jan 1, 1963

By Amar Prakash, V. M. S. R. Murthy, VIVEK KUMAR HIMANSHU, Sufal Mehrotra, Ashish Kumar Vishwakarma

Raises are vertical or inclined openings made to connect two levels of an underground metalliferous mine. They are developed using drilling and blasting-based technique or by mechanical means. Raise boring machines (RBM) have evolved in recent years, which provide quicker and safer raise excavation. The penetration rate using RBM has influenced applied thrust. The required thrust to enhance penetration rate with optimal use of energy would be different under varying geological and geotechnical conditions. In this study, the influence of applied thrust on penetration rate using RBM has been investigated. The investigation has been made for two different rock types, amphibolite (AMP) and garnet-biotite-sillimanite-gneiss (GBSG). The numerical simulation model was developed for this purpose using Ansys-Explicit Dynamics. The induced tensile stress under different conditions of applied thrust has been analysed in the calibrated numerical model. The model output shows the power trend between the parameters. The experimental data on penetration rate was also collected along with the respective operational parameters. A statistical analysis has been carried out for the gathered data. The analysis of data also shows a power trend between thrust per cutter and penetration rate in both rock types and hence validates the numerical simulation-based output. Based on the outputs of the numerical simulation and empirical study of the experimental data, the optimum thrust per cutter for excavation in both rock types is in the range of 12–14 tons. The approach used in this study can be helpful for predicting the optimal operational parameters of raise boring machines under different geological/geotechnical conditions.

May 29, 2023

By John F. M. Sims

Political issues and a glaring infrastructure deficiency have retarded the emergence of a strong mining component to the Alaskan economy in recent years. Barriers to orderly mineral development are slowly being removed attendant upon changing political circumstances. Infrastructure development, as an investment avenue as well as a responsibility of the State, is receiving much greater attention than in the past. Alaska of course has a rich and varied mining history going back to the 19th Century. This paper, however, focuses on the mining potential, not the mining heritage of the 49th State. The mining industry is emerging from a nadir in the economic cycle - times during which it was buffeted by unsympathetic administrations and confused and confounded by the protracted land status- conflicts prior to enactment; of the Alaska National Interest Lands Conservation Act (ANILCA) and other milestone legislation. Today Alaska's mining industry looks toward a bright and healthy future and, in the process, will become a very important and vital component of the State and national economy.

Jan 1, 1982

By D. Castillo

The effectiveness of a flotation column is due principally to the addition of wash water to the froth phase. The wash water flow rate can be significant, especially so for systems yielding a high weight recovery of fine solids, e.g. zinc sulfide flotation. Therefore, it is critical to recognize and assess the impact of the water addition upon upstream separation stages. This paper examines column flotation circuit configurations using data from a portable 2 t/day pilot plant. The objective is to provide an improved basis for column design, either as a retrofit or as part of a new circuit.

Jan 1, 1990

By B. Pesic

This is an extension of the work on recovery of silver and manganese from Ag-Mn ores, and recovery of silver and gallium from flue dust from phosphate industry. Carbon adsorption was considered as the most adequate method for recovery of silver from thiourea leach solutions. For this reason it was decided to examine the characteristics of adsorption of silver on activated carbon. Coconut hard shell activated carbon was used for this study. Ag(TU)2C1 complex was dissolved into thiourea solution to give 2 gpl stock solution. Thy studied parameters were: loading isotherms at 25°C, 35°C, and 45°C, initial kinetics as a function of thiourea concentration, temperature, pH, N2, and O2. It was found that the loading capacity of carbon for silver and thiourea was 137-150 mg/g and 514 mg/g, respectively, at 25 °C.

Jan 1, 1986

By Sakshi Hazuria Anderson, Angela Binder, Oscar Jaime Restrepo Baena, Simit Raval, Sandra Nowosad

As the mining industry faces times of change, new challenges arise to ensure raw material supply for future generations. Different scenarios are currently shaping the way we mine and teach mining engineering. Led by an increasing demand for raw materials, net-zero requirements for improving long-term operation performance, technological advancements such as automation and digitalization, safety improvements, environmental considerations and a need for social acceptance, mining is pursuing to change and adapt to these requirements at a faster pace. Such changing times raise new concerns, one of the most relevant is the lower number of students interested or enrolling in mining engineering and related fields, leaving mining engineering as one of the less preferred career options for students. Nonetheless, it is essential to continue addressing and supplying the skill sets that are suited to the contemporary and future mining industry. To this end, globally, academia is currently undergoing several initiatives such as curricula updates and adaptation, upskilling, improving teaching practices and techniques, including e-learning techniques, enhancing industry-academia and inter-university collaboration, and much more. In countries like Australia, where mining plays a crucial role in the economy, the need for curriculum updates is more pressing than ever. As the mining industry evolves with new technologies and sustainable practices, there is a growing demand for a workforce skilled in these modern approaches. Recognizing this necessity, universities such as the University of New South Wales and Curtin University have taken significant steps to revamp their educational programs. By updating their academic offerings, both universities aim to equip graduates with the necessary skills to drive innovation and sustainability in mining, supporting Australia’s development as a leader in this critical sector. Moreover, the selection of topics that drive curricula update and the focus of the research institutions in mining engineering must extend beyond mere technological and technical aspects to include social and ethical dimensions. In this context, the Universidad Nacional de Colombia, in association with the Colorado School of Mines, has introduced the topic of humanitarian engineering (HE) in 2020. HE is a sociotechnical approach that focuses on developing engineering solutions that promote the sustainable development of communities addressing their basic needs and aiming to improve their quality of life (Menéndez-Aguado et al., 2023; Smith et al., 2023). By focusing on sustainable development, community engagement and equitable resource distribution, HE helps the industry build positive relationships with stakeholders, reduce conflicts and foster social license to operate. As the mining industry seeks sustainable and socially responsible practices, future engineers require training in this area to understand the broader impacts of their work, fostering a mindset that prioritizes community well-being and environmental stewardship alongside technical proficiency. However, developing skills toward humanitarian engineering and sustainable mining among new generations of mining professionals remains a complex task. Integrating the necessary content to prepare future engineers for the multifaceted demands of the industry into a single study program poses significant challenges. To address these complexities, modern educational approaches such as the ones integrated in the mining engineering programs at Clausthal University of Technology can be leveraged to enhance both teaching and learning experiences (Binder, 2024b; Bothe-Fiekert et al., 2023; Nowosad et al., 2024). Innovative teaching methods, such as blended-learning, project-based learning, case studies, scenario simulations and interdisciplinary collaborations, can help bridge gaps by fostering critical thinking, creativity and empathy among students. By embracing modern pedagogical strategies, institutions can better equip future engineers to navigate the evolving landscape of the mining industry responsibly and effectively.

Dec 1, 2025

A portable electronic instrument was developed which will measure change of longitudinal wave velocity with change of uniaxial stress in rock columns. The instrument is a solid-state device powered by nickel-cadmium batteries. It uses a probe of two piezo-electric crystals spaced inches apart to send and receive a pulse through a stressed rock. A one-inch cathode ray oscilloscope visually displays the longitudinal wave. A reference chart is used to find the stress. Laboratory results have indicated that the average stress on a sandstone column can be found to within 35 psi. The feasibility of using this instrument to determine stresses in mine pillars is to be studied. The instrument may be used to investigate physical properties of rock.

Jan 1, 1970

By J. H. Bassarear

Conventional crushing and grinding circuits are compared to semiautogenous circuits. Recent installations of each circuit are reviewed and seven methods of using autogenous or semi- autogenous techniques are described. Steel and power consmption data are reported and benefits of a dedicated digital computer are discussed.

Jan 1, 1981

By A. Newman, M. Goycoolea

"In this paper, we consider an underground production scheduling problem consisting of determining the proper time interval or intervals in which to complete each mining activity so as to maximize a mine’s discounted value while adhering to precedence, activity durations, and production and processing limits. We present two different integer programming formulations for modeling this optimization problem. Both formulations possess a resource-constrained project scheduling problem structure. The first formulation uses a fine time discretization and is better suited for tactical mine scheduling applications. The second formulation, which uses a coarser time discretization, is better suited for strategic scheduling applications. We illustrate the strengths and weaknesses of each formulation with examples.IntroductionProject scheduling is an important aspect of underground mine planning that consists of determining the start dates for a given set of activities so as to maximize the value of a project while adhering to operational and re-source-availability constraints. Important activities that require scheduling include development, drilling, stoping and other ore-extraction techniques, and backfilling. Precedence relation-ships impose an order in which activities can be carried out based on their location in the mine: for example, the activity a associated with development of an area must be completed before the activity a´ associated with extraction of that same area can begin. Re-sources include attributes of the mining operation, such as the amount of extraction and mill capacity available per time period, and are determined by capital and equipment availability and other factors. In this paper, for our set-ting, resource-availability constraints consider the amounts of material that can be extracted and sent to the mill — that is, processed — per time period."

Mar 1, 2017