Search Documents

By T. P. Meloy

The packed column flotation cell is an awesome separation device. Virtually unknown and untested, the packed column flotation cell is one of the ten most important developments in mineral processing of the 21st century. Though experimental and industrial data is limited, it is clear that the packed column flotation cell is two to three orders of magnitude better than the conventional flotation cell and one to one and a half orders of magnitude better than the open column flotation cell. With the modern packing taking up less than one percent of the packed column, column blocking does not occur. For a packed column operating 24 hours a day, 365 days a year, the estimated mean time between failures (MTBF) is one hundred thousand hours or roughly twelve years. With no moving parts, lower maintenance costs, lower power consumption and inherent operating stability, the packed column is a powerful separating machine. Because there is little meaningful data for comparing the packed column to the conventional flotation cell and the open column flotation cell, much of the material presented in this paper are guesstimates. They are disinterested guesstimate made by the authors after extensive theoretical work and reviewing the known facts. In the authors' opinion, no available data contradicts the guesstimate. The authors expect that there may be errors as large as three hundred percent. Even three hundred percent errors will not change the conclusions of this paper. The packed column flotation cell is a formidable separating device. To understand the problems of comparing the three types of flotation cells, consider the fact that the three cells may have different modes of separation. One of the authors, Meloy, believes that in the conventional cell, the primary particle separation takes place in the liquor with secondary separation taking place in the froth, while for open column flotation, all the separation takes place in the froth. However, he believes that in the packed column a large part of the separation may take place on the walls of the packing. If this is true, not only is the method of modeling each type of cell different, but the method of particle selection in the cell is different. This means that one type of cell may be better at differentiating between two different types of particles. There is a growing body of literature on open and packed column flotation. Suggested reading: (Clarke et al; Hucko et al; Li; Smith & Warren; and Yang).

Jan 1, 1994

By Bruce L. Bryson

In the past decade a principal growth area in refractory technology has been the development and use of extra high alumina refractories. The refractories user is asking for, and is prepared to pay for, higher purity, more dense materials with longer life, less maintenance, and better dimensional tolerance to meet the exacting demand of high output processes. High alumina and bauxite refractories are being used more and more to keep pace with the demand for guaranteed performance. The steel industry, for example, is starting to place great reliance on these products. A unique material now available with all the requirements for extreme purity and density is tabular alumina, already proving itself in many refractory applications.

Jan 1, 1973

By J. O. Down

St. Marys Cement Company operates two cement plants in Southern Ontario, Canada. The original plant, located at St. Marys, a town 20 miles north of London, Ontario, began operations in 1912. A second plant, located at Bowmanville, Ontario, 40 miles north east of Toronto, began operations in 1967. In June 1973, St. Marys Cement began feasibility studies of modernizing their wet process plant at St. Marys. Over its 61 year life, this plant had been expanded from 335 m. tons per day (375 s. tons per day) to 2000 tpd (2200 s. tons per day), with all the original equipment retired several years ago. The objectives of the feasibility study were to develop a conceptual plan for a dry process plant and to de-, fine the appropriate process method and equipment. This study proceded along four fundamental fronts: a) How could the clay raw material, a glacial till with up to 20% boulder content, be processed in dry form and beneficiated? b) Were the raw materials suitable for the most efficient form of dry process kiln, the 4-stage preheater? If a 4-stage preheater kiln is selected should it utilize a precalciner? c) What type of clinker cooler should be used? d) What environmental constraints would be imposed on this plant and how can they be reconciled with capital and operating limitations? During the feasibility stage, pilot plant work was done on two possible solutions to the clay problem, operating plants in Europe were visited and discussions held with kiln and mill vendors.

Jan 1, 1977

By Chester O. Ensign

The White Pine Mine is situated in the southwestern portion of the Keweenaw Peninsula of Upper Michigan approximately 6 miles south of Lake Superior (Fig. 1). It is east of the Porcupine Mountains in Ontonagon County. The ore deposit is about 70 miles southwest of the famous native copper deposits of the "Copper Country" lying northeast of Houghton. Geological conditions are different at every mine and create a special set of problems in dilution control. This paper is largely intended to describe the techniques applied in mine dilution control (grade control) at White Pine, and present results of the program. For necessary background information major geologic characteristics of the deposit, particularly those that exert control over the distribution of ore, are briefly discussed. Mining methods are described in considerable detail since applied grade control techniques are adapted to these.

Jan 1, 1964

By Dan Swidrak, Bill Zietlow

Halfway through a 17,770-ft long stormwater tunnel, an 11-ft diameter TBM encountered a karst void below the Mississippi River in Missouri, resulting in significant inflow. It was decided that the TBM could not safely advance without external intervention. Low-mobility grout was pumped from the surface. A rescue shaft was constructed and a conventional tunnel with spiling support was mined back to the machine. The TBM was removed and a 14-ft diameter TBM equipped with probing drills was relaunched. Probing from the new TBM encountered one additional karst feature but the machine advanced after grouting and successfully completed the tunnel.

Jun 23, 2024

By M. L. Wouden

The Bureau of Mines investigated pegmatite and granite formations at Copper Mountain, Fremont County, Wyoming, for recovery of tantalum and niobium. Sampling of surface exposures identified about 1.27 mega tonne of pegmatite resource material ranging between 0.02 and 0.04% Ta20, and 0.007% Hb20,. Beneficiation studies were conducted involving coarse-grained and fine grained pegmatite samples. Over 80% recovery of the coarse-grained tantalite was achieved in a concentrate averaging over 45% combined tantalum-niobium oxide. Lower concentrate grades and recoveries resulted from the treatment of fine-grained pegmatite.

Jan 1, 1991

By G. Soni

A first principle flotation model has been derived from the basic mechanisms involved in flotation. The model consists of a series of analytical equations for bubble generation, bubble-particle collision, attachment, detachment, and froth phase recovery. The model can predict flotation from both hydrodynamic and surface chemistry parameters such as bubble size, particle size, energy dissipation rate, ?-potentials, contact angles (?), etc. The model has been validated in a series of laboratory batch flotation experiments, in which mono-sized glass beads are used as feeds. The experimental results are in good agreement with model predictions both in terms of grade and recovery.

Feb 23, 2014

By A. Haile, A. Poole

During 2001-2002, the Granny Smith Mine of Western Australia undertook the development of a planned circular failure. Excavation took place in an interim pit wall that intersected the transported sediments, lake clays, and palaeo channel sands that overlay the deposit. The purpose of the study was to refine feasibility level slope parameters used for the initial design of the Wallaby pit, with the intent of increasing the overall slope when excavating the ultimate pit limits. During excavation, the geological and hydrogeological characteristics were studied in detail and data was collected using area-specific instrumentation and monitoring. Failure occurred in mid February 2002, at which time a detailed survey of the excavated slope using laser technology was conducted to provide geometric information suitable for back analysis of the material shear strength. The slope failure and associated information was analysed by geotechnical consultants. The revised shear strength and hydrogeological parameters were then applied to design the final pit walls. The slope redesign provided a cost saving of approximately seven hundred thousand US dollars. Design, slope formation, back analysis, the geology of the clay units, the hydrological environment, planned infrastructure, management and safety issues, and the on-going slope performance of the final slope are discussed.

Jan 1, 2004

By Yuting Xue, Mark Van Dyke, Zoheir Khademian

Borehole scoping has been widely used in the U.S. underground coal mines as a method for geologic mapping and stability analysis because it is very useful for identifying rock types, voids, fractures, and formation boundaries through the direct observation of the borehole wall. An image stitching technique was proposed to generate panoramic borehole images from side-view borescopes in a previous study. However, the generation of panoramic borehole images can be affected by the borehole condition because the image stitching process highly depends on the key point detection and matching. The presence of dust and water could have a significant influence on the detection of key points. In this study, the influence of borehole conditions on panoramic borehole images was studied from the success of image stitching and the visibility of geologic features and lithology changes. Borehole videos recorded at different times, when the same borehole was freshly drilled, freshly washed with water and 12 days after washing, were processed with the proposed technique. The comparison of the stitched images shows that the presence of dust has minimal influence on the image stitching process but shows significant negative effects on the visualization of geologic feature and lithology change. In addition, the presence of water can significantly hinder the image stitching process, which in turn helps in identifying lithology change. Borehole scoping aids in identifying and mitigating hazardous conditions in underground mines, and this study provides preliminary inputs into identifying optimum borehole conditions for geologic mapping with panoramic borehole images.

Feb 1, 2025

By Dion Weatherley, Raúl Castro, RENE GOMEZ, Pablo Cid

The study examines the impact of different drawbell geometries on hang-ups during ore extraction in underground mining. Using the discrete element method, the research compares three drawbell geometries: drawer, circular, and El Teniente. The findings indicate that the El Teniente geometry experienced more hang-up events, while the circular geometry had fewer.

Sep 1, 2023

By G. J. C. Young

The paper describes the replacement of a conventional filtration, clarification and zinc precipitation plant by a carbon in pulp (CIP) electrowinning plant, with the objective of improving the recovery of gold from cyanide leached, acid plant calcines. The discussion covers the early laboratory studies to the design and erection of the full scale plant. Particular emphasis is placed on the problems encountered with commissioning and the strategies which were employed to solve them.

Jan 1, 1982

By Fouad Faraj, Julian M. Ortiz

Within the natural resource industries, there is an increasing amount of data and number of variables being recorded when sampling a site. This has made multivariate geospatial datasets more difficult to analyze, in particular the definition of estimation or simulation domains used in geostatistical analysis. Establishing these domains is typically the first step for any subsequent geostatistical workflows or modeling. Domains are traditionally established using categorical data such as lithology, mineralization, or alteration from geological logging and are aimed at identifying distinct populations with particular geological, spatial, and statistical features. The manual logging process is time-consuming and costly but is required because defining geologically homogenous volumes is crucial for the planning, extraction, and processing of natural resources. Classical clustering methods have aided in analyzing the multivariate datasets, but the resulting clusters from these methods do not correlate well with geological logging and do not allow practitioners to input their knowledge of the domain in the clustering process. In this work, a simple unsupervised classification workflow is presented which allows the practitioner to input domain knowledge by selecting relevant variables to cluster reasonable geological domains. This can be used as a tool to aid the manual logging procedure or as a tool to establish domains for different uses such as defining zones with different rock hardness distributions which allows the corresponding volumes to be sent to appropriate mills for efficient mineral processing. The performance of the workflow is assessed on a mining dataset using the geochemical information and validated with the geological logging.

Apr 16, 2021

By Robert L. Sundeen, Richard V. Wenberg

Overshot loaders are loading machines which fill a front-mounted bucket by crowding and bucket lifting, passing the loaded bucket over the machine and throw¬ing the load into a haulage unit to the rear. The load is retained in the bucket as the load mass is accelerated in its path over the machine. At the point of discharge, the bucket is stopped suddenly and the load leaves the bucket, following the throw trajectory past the rear of the loader. Fig. 1 shows a typical overshot loader of this type. Overshot loaders were developed for loading in nar¬row drift headings and drawpoints, where it is impossible to place or pass a haulage unit alongside the loader. Haulage access is to the rear of all overshot loaders. The first overshot loader was developed in the early 1930s. The early machines were rail-mounted, air¬powered, and had small loading capacities. To this day, the same basic design configuration exists, and all suc¬cessful overshot loaders still use compressed air. Bucket sizes range from 0.14 to 0.59 m3 (5 to 21 cu ft). The most commonly used machines are rail-mounted, al¬though crawler versions are popular for special applica¬tions, particularly shaft sinking. Rubber-tired machines have found some application where a greater travel distance is required between the loading and discharge points. CONDITIONS INFLUENCING APPLICATION Roadway Type Rail-mounted loaders are used where soft bottom requires rail support or where the long haul is ac¬complished with rail. This situation usually occurs in civil tunnels or in mine drifts that will continue to utilize rail-bound main haulage after development work is completed. Crawler and rubber-tire mounted loaders are used where the roadway surface is rough and lateral travel beyond the range of rail-bound machines is required. Work Area Dimensions The largest rail-bound loaders can clean roadways as wide as 4 m (13 ft) from a single track. Wider headings require multiple trackage. Headroom require¬ments are dependent upon the path described by the bucket as it passes over the machine. The largest over¬shot loader requires approximately 3.4 m (11 ft) of headroom. It follows that the largest heading that can be driven by overshot loaders from a single set of rails is approximately 4 m (13 ft) wide and a minimum of 3.5 m (11.5 ft) high above the rail. The smallest rail-bound loaders can work efficiently in headings as small as 1.8 m (6 ft) wide by 1.8 m (6 ft) high above the rail.

Jan 1, 1982

By George J. Karabin

Over the past few years, the use of fully grouted bolts to support the roof of underground openings has increased dramatically. While conventionally anchored bolts effectively reinforce the strata of over 80 percent of mine workings, the use of resin grouted bolts in areas of severe roof conditions has resulted in a substantial reduction in roof falls and an overall improvement in both safety and production. The Roof Control Group of Pittsburgh Technical Support Center, Mining Enforcement and Safety Administration, has conducted numerous field and laboratory investigations to isolate parameters which contribute to the effectiveness of both conventional and resin bolting systems. Specially developed strain-gamed resin bolts, compression pads and differential sag stations installed during the mining cycle have generated data reflecting the loading characteristics and resulting roof stability associated with each type of support. Additional investigations have produced optimum installation parameters of the two systems including the effectiveness of thrust/torque controls for conventional bolts and various bolt/ hole diameter combinations for fully grouted rods. Theoretical analyses, coupled with the actual field and laboratory findings and numerous installation observations have facilitated basic comparisons of the working mechanisms and failure modes of both resin and conventional systems.

Jan 1, 1976

By B. K. Parekh, R. H. Mehta

Handling of fine coal is an importance issue for coal as well as the utility industry. Reconstitution in form of pellet or briquet would be desirable if it could be done economically. This paper evaluates the effectiveness of three binders e.g., asphalt- emulsion, corn starch and Brewex, in forming pellets of ultra-fine clean coal. It was found that asphalt emulsion and corn starch were not effective binders for ultra-fine clean coal, however, Brewex provided excellent quality of pellets, which exceeded all the minimum quasi requirements of coal pellets. INTRODUCTION Advanced coal preparation techniques (physical or chemical) are designed to process ultra-fine (minus 200 mesh or 74 pm) coal. The average particle size of the clean coal product is about 25 pm. Currently available dewatering techniques are effective in providing a 25 to 30 percent moisture product of this size coal slurry (Parekh et al. 1989). Handling and utilization of this dewatered ultra-fine size coal is difficult. Reconstitution, which includes pelletization, briquetting, extrusion, etc., of the dewatered coal product provides an ideal answer to handling and transportation problems. However, reconstitution of fines in the coal industry has not been successful due to various reasons. The most important criterion for its unsuccessful application in the coal industry is the cost of the binder (Capes et al. 1965). Various methods of reconstitution, such as briquetting, disk pelletization, extrusion pelletization and roller and die-pelletization, have been tested for fine coal agglomeration (Conkle et al., 1991) (Richards, 1990). Conkle et al., (1992) have provided a detail analysis of each technique in terms of moisture and operating cost requirements. According to Conkle, briquetting requires a product containing very low moisture, whereas pelletization can be done with coal containing up to 30 percent moisture. Currently available dewatering technique provides about 25 percent moisture product, thus, pelletization appears to be an ideal route for reconstitution. In this paper, results are presented on the comparison of three different binders i.e., asphalt-emulsion, corn starch and Brewers condensed solids (BCS or Brewex), for fine coal pelletization.

Jan 1, 1995

By Alena Johnson

"Much of the copper being produced today uses heap leaching, where pure metal is extracted from the ore with a chemical process rather than smelting. This technique is deployed extensively in major copper producing areas including Chile, Peru and the southwestern United States.Copper ore is excavated from the ground, crushed and then spread in uniform layers on a pad. A slow trickle of sulfuric acid is distributed over the pile, where it percolates to the bottom and a collection point. The acid leaches out the copper, along with other minerals, which can be extracted chemically. This process can be used at large sites producing 100 kt/a (110,000 stpy) and greater.Production on a massive scaleProduction at heap-leach sites is continuous and can operate on an enormous scale. The ore is fed into a crusher to break down the large pieces, and then it moves into an agglomerator to capture the fines and create more uniform particles. While in the agglomerator, the ore is mixed with acid for the first time, helping it to bind the fines into larger particles and starting the leaching process. The treated ore moves by conveyors to a stacker designed to spread it uniformly on the pad.The size of the operation comes into perspective by considering a typical pad measures 1.6-km (1-mile) long and 0.8-km (0.5-miles) wide. Working day after day, the stacker creates individual piles or modules on the pad, each 122 x 61 m (400 by 200 ft) and 3 m (10 ft) deep. When one module is filled, it moves across the pad to the next, filling the area in one continuous pile. A completed row of modules spanning the width of the pad is a cell. Once the entire pad is covered, the process begins again laying down another 3-m (10-ft) layer, and it continues until the entire pad reaches its height limit which can be several hundred feet.Once a new module is completed, technicians lay a network of plastic pipes over the surface in a pattern similar to agricultural drip irrigation installations. The diluted sulfuric acid, called raffinate, is pumped through the pipes so it can be distributed over the module, allowing the acid to soak through the ore and leach out copper as it percolates to the bottom. At the same time, approximately 35 to 45 percent of the acid is consumed by dissolving the calcite carrying the metal in the process. The raffinate reaching the bottom is now characterized as pregnant-leach solution (PLS) since it carries the copper the company is seeking to recover."

Jan 10, 2018

By Philip A. Bucci

The Florida phosphate industry successfully uses froth flotation to concentrate phosphate in: the particle size range of approximately 28 to 150 mesh. However, as recently as 1965, coarse particles in the range of 14 to 28 mesh generally had not been beneficiated by conventional flotation methods at recoveries high enough to be considered adequate. It has been customary to upgrade this coarse material; by "agglomerate flotation" or "skin flotation" using belts, tables or spirals. While these devices have proved commercially effective, their capacities are much lower than those of froth flotation cells. To determine whether coarse phosphate material could be recovered successfully by froth flotation, Armour Agricultural Chemical Company began a series of pilot and plant tests; in April 1965. Objective of the tests was to compare over-all performance of a froth flotation cell design relatively new to the phosphate industry with results from the belt circuit at the Bartow, Fla., plant.

Jan 1, 1966

By James L. Withiam, P. C. Kelsall

The manuscript of this paper was not available for publication when the Proceedings went to press. Should the authors elect, they may distribute copies at the time of the Symposium.

Jan 1, 1986

By Subhash Bhagwat

The definition of high sulfur coal varies from plant to plant and is subject to changes over time as the environmental regulations change. In plants constructed after September 1978 hardly any domestic coal can currently be burned without the use of Flue Gas Desulfurization (FGD) because a 70 percent reduction in potential S02 emission is mandatory even when the potential emission is less than 0.6 lbs. S02/106 Btu heat input. On the other hand older power plants may in many cases be legally emitting up to 6 lbs. S02/106 Btu or more under some State Implementation Plans (SIP). The Clean Air Act requires, however, that in the long run all stationary sources of S02 pollution must abide by the ceiling of 1.2 lbs S02/10 Btu heat input.. Coals with a potential to exceed this limit must, therefore, be considered as high sulfur coals. Such a definition would be unrealistic because many SIP's aim at an emission level of 1.8 to 2.0 lbs. SO2/106 Btu for existing plants and a stricter limit does not appear to be enforceable in the next 5 to 10 years. As a result, coals with an emission potential of greater than 2.0 lbs of S02 per 10 Btu heat input are considered high sulfur coals for the purpose of this investigation. Based on this definition and the 1984 actual consumption of coals by U.S. electric utilities (table 1) only 7 out of the 24 coal producing states could be categorized as low sulfur states. The actual S02 pollution, however, depends on total tonnage of a type of coal as well as the sulfur content of the coal. Table 1 also indicates that only 6 states--Kentucky, Illinois, West Virginia, Ohio, Pennsylvania and Indiana-account for nearly 77 percent of S02 pollution potential in the United States. These 6 states have therefore been chosen for this investigation.

Jan 1, 1986

By William H. Breeding

The remarks that follow are based substan¬tially on experience covering 45 years, 80% of which have been in placer work, rather than on a review of available literature. Most commercial placers have been deposited by the action of water. The richer and more-difficult-to-mine placers are those in the headwater areas where gradients are steepest. The most lucrative placers are generally in intermediate areas where volumes are greater, fewer boulders are present, and gradients are from 3% to 1 ½ . The higher volume, lower grade placers are in the lower reaches of river systems where gradients are lower. Where gold-bearing rivers have discharged into the sea, wave action can concentrate values on beaches, past and present.

Jan 1, 1984