Search Documents

By Frank C. Appleyard

As the environmental movement gained force during the past few years, it was inevitable that attention would be focused on surface mining, and we have seen this method of extracting minerals from the ground come under heavy attack by conservation groups, the press and television, legislators at all levels of government,, and the public at large. It is difficult, and in some situations, perhaps impossible, to measure either the need for, or the results of, land reclamation in absolute terms. Therefore, much of the criticism of surface mining has been based upon subjective analysis rather than hard data, with the result that discussion of the subject often includes a fair amount of emotional response. To be fair, this reaction is not limited to just our critics; even we hard headed engineers sometimes respond in the same way, an observation with which you may agree when I finish this talk. This leads to the thought that whether you are for it, or against it, land reclamation in many respects is a state of mind. That is, our reaction to it can vary considerably, depending on how far we have thought it through. And think it through we must, because the pressures being brought to bear need to be met with positive actions if the problem is to be brought under control, and in the next few minutes I would like to discuss from a management point of view some ideas which might aid in this thinking process. It would be a mistake, I believe, to think that the current energy crisis will suddenly bring the environmental movement to a stop, and therefore, we can relax and go back to running our busi¬ness the way we used to. This is not realistic; on the contrary the energy crisis is focusing attention on the limitations of our natural resources as nothing else could, and with respect to land

Jan 1, 1974

By ANA E. BOHE, MICCO GEORGINA DE, GASTON G. FOUGA, JUAN P. GAVIRIA, FEDERICO J. POMIRO

To the best of our knowledge, this paper comprehensively summarizes a thorough study to determine the thermodynamic viability of the reactions between light rare earth oxides and chlorine with and without carbon. The kinetics and mechanisms of light rare earth oxide chlorination and carbochlorination reactions are analyzed and discussed according to results in the literature. Lanthanides between lanthanum (La) and gadolinium (Gd) are considered as light rare earth elements (LREEs) in agreement with previous literature and the results detailed in this review. Both laboratory- and industrial-scale light rare earth chlorinations and carbochlorinations, starting from oxides and ores, are reviewed.

By Louis M. Perlman

Quantitative methods are, by now, a standard tool of the mining industry, and are commonly used by Research Departments in their evaluation of production methods and schedules, and their associated costs. Indeed, much sophisticated computer work has been devoted to such evaluation of controllable costs and capital requirements. These data are an important input into the project evaluation formula, which is probably the most important single calculation per formed by a mining company, since the result decides whether a particular project is viable. It is instructive to summarize the broad principles of project evaluation, since they are crucial to the remaining sections of this paper. PROJECT EVALUATION The most widely used method of appraising projects is known as Discounted Cash Flow (DCF) method. Two main variants are used; they are known as the 'not present value' (NPV) approach and the 'internal rate of return' (IRR) approach respectively. The difference between the two is that the former takes the firm's interest rate as given and uses this knowledge to calculate the present value of the project; whereas the latter calculates the highest interest rate the project could tolerate and still just breaks even. The technique is more simply discussed in terms of the first method (NPV).

Jan 1, 1972

By Stuart W. Maher

A major problem in future discoveries of base metals is their "explorability". By this I mean an exploration program must be designed that assures accurate assessment of the potential for ore, but is within reasonable budgetary constraints. As we are compelled to depend more and more on non-outcropping prospects, "blind" deposits, and as drilling costs multiply, the costs of exploration increase significantly. Solutions to the problem of defining exploration targets are influenced by our conceptions of the origin and recognition o f conditions that localize ore. The maxim that "elephants should be sought in elephant country" presumes we can recognize elephant country. This paper presents a suggested origin for some mineral deposits, and their controls; particularly those termed ?Mississippi Valley type". Tennessee is used as an example of the ideas offered. Mining districts designated "Mississippi Valley type" are, and have long been, the principal sources of barite, fluorite, lead and zinc ores in the United States and elsewhere throughout the world. A large volume of literature is available describing this class of ore deposits, explaining their habitat, and invoking genetic models for them. The quality of this literature is notably uneven, some of it demonstrably erroneous, and much of it is restricted to detailed descriptions of one aspect of the problem, or to detailed descriptions of one aspect of the problem, or to a single mine, or even a single stope. If an ore deposit is thought

Jan 1, 1977

By Robert R. Dorfler

AMPS[. has completed a rationed grinding ball test in a 2.93 m x 2.93 m ball mill at Climax Molybdenum Company. The test consisted of purging the ball distribution formed by charging 100%, 76 mm carbon steel balls with a distribution formed by charging 50% 76 mm and 20% 51 mm alloy steel balls. The resulting change in ball surface area yielded improvements in both tons ground and fineness of grind with a significant reduction in total ball consumption. This paper summarizes preliminary studies leading to the plant test, grinding efficiency results, and future plans to optimize the ball charge.

Jan 1, 1981

By G. H. Schnakenberg

In 1986, the US Bureau of Mines (USBM) embarked on a major research effort to develop technology that could substantially reduce worker exposure to face hazards by simply relocating the equipment operators to an area of relative safety. This reduced-exposure mining system (REMS) research effort enhances the USBM's ongoing health and safety efforts aimed at reducing and controlling dust and noise and reducing accidents through training and better mining practices. This paper reports on the progress made on the developing research and demonstrates the technologies required for the computer-assisted teleremote operation of continuous mining machines, haulage systems and roof bolting machines.

Jan 1, 1997

By Drew Hobert, John Nielson, Erich Dohm

Metallurgical coal is an essential component for the blast furnace-basic oxygen furnace (BF-BOF) steelmaking process, which accounts for roughly 70% of total global steel production. To meet the growing demand for metallurgical coal, Arch Resources identified the potential to recover low- ash coal from ultra-fines discarded prior to the deslime flotation circuit across their portfolio of operations. Historically, many flotation circuits were designed to discard this ultra-fine coal due to high clay content and technological barriers to cost-effectively upgrade and dewater the coal to a saleable product. Recent advancements in high-intensity flotation technology, including the Eriez StackCell, have enabled coal producers to recover ultra-fine coal while minimizing capital and operating costs. In July 2023, Arch Resources commissioned the first full-scale ultra-fines recovery circuit utilizing StackCell high-intensity flotation technology at the Leer Mining Complex. This paper reviews the approach utilized to develop the flotation process design, learnings from the commissioning and ramp-up period, and performance data through the first year of operation.

Feb 1, 2025

By Nikhil Dhawan, Shrey Agrawal

India’s most extensive renewable energy expansion program targets 280 GW of solar energy by 2030. Due to the massive generation of photovoltaic waste (expected 34,600 T by 2030), stringent recycling effort to recover metal resources from endof- life PVs is required for resource recovery, circular economy, and subsequent reduction in the environmental impact. The present study investigates the recycling potential of end-of-life silicon solar modules. The feed characterization reveals that most of the values in PV modules are concentrated in the frame (pure Al), Si wafer (72–84% Si, 9–12% Al, and 0.13–0.71% Ag), and electrical connections (Cu wire coated with Sn). The Si and Ag values in the feed were beneficiated using water fluidization, and concentrate with 90% Si and 2% Ag was attained in the underflow concentrate. Ag values were recovered in the form of AgCl by leaching in nitric acid and precipitation. After the purification step, the residue containing 99% Si can be further utilized to fabricate Si wafer and Al-Si alloy. The preliminary cost estimations suggest that the proposed process is economically viable for the recycling of solar panels with the maximum value generated from the AgCl precipitate followed by Al panels and Si wafers.

Nov 14, 2022

By JIACHENG XIE, Juanli Li, Wenyong Du, Tao Cui, Mengyao Dong, Pengfei Huo

The study proposes a dynamic path planning method for mining equipment based on spatial kinematics and real-time correction of coal-rock state identification. The method integrates real geological data and equipment operation information to improve the autonomous cutting of fully mechanized mining equipment.

May 1, 2023

By Russell Frith

A review of published literature reveals case histories whereby the entire periphery of a coal pillar has “burst” out as a single event during first workings, the associated energy and material release causing significant damage to adjacent roadways and any equipment/infrastructure located within said roadways. Such events are distinct from coal burst events during first workings such as that at the Austar Mine in 2014, or those linked to overburden bumps related to either horizontal stress-driven slip along major faults and/or thick, massive strata units in the overburden or floor of the coal seam.

By J. Kalliokoski

As part of a funded project we have completed a comparative literature survey of the US regional Proterozoic geology. For our com¬parative study model we used the geological settings of the very large pitchblende deposits in Saskatchewan, Canada and the Northern Terri¬tory of Australia. These occur in a variety of Archean and Lower Proterozoic host rocks, at and below a regional unconformity that is capped by subhorizontal Middle to Upper Proterozoic conti¬nental sedimentary rocks. We find that there have been recorded in some parts of the US similar unconformable sequences of Middle to Upper Proterozoic continental sedimentary rocks that overlie older basement rocks.

Jan 1, 1979

By J. R. Maxwell

The development, commercial installation, and operating performance of large capacity Maxwell Flotation Cells. Volumes ranging from 300 cubic feet to 2,000 cubic feet per flotation mechanism.

Jan 1, 1971

By Yuting Xue, Danqing Gao, Brijes Mishra

Heterogeneity and discontinuity significantly affect rock strength. For accurate stability prediction, intact rock behavior is imperatively included in rock mass behavior. However, past research largely used arbitrary scaling approaches to produce rock strength. This paper considers a stochastic approach in order to determine the strength of a rock. Based on the laboratory data, a MATLAB® with extreme value stochastic model generates a database for each physico-mechanical property. Then FLAC® simulates laboratory-sized rock specimens. The grids developed in the numerical model can in turn develop random material properties in MATLAB®, which researchers then applied to the final FLAC® model. Model runs simulate the approach performed in the laboratory. The results from the model indicate that a stochastic approach produces strengths that are lower than a deterministic approach. Failure modes for each specimen are different, similar to observations in the laboratory. In addition, random density also influences the failure mode, highlighting the importance of stochastic analysis in rocks.

By Jack A. James

Lancaster Lime and Stone Corporation developed a quarry operation in 1971 and 1972 for the production of high calcium limestone and construction aggregates, or roadstone. The quarry operation is situated in southeastern Pennsylvania in the northern part of Lancaster County. The geology of the high calcium limestone deposit had a powerful influence on all aspects of planning this operation. My purpose is to trace the influence of geology throughout the planning and thereby point out the discipline that geology imposed on the planning, and indeed, continues to impose on the operation. Lancaster Lime and Stone Corporation is one of four wholly- owned subsidiary companies of Kurtz Materials Corporation. Kurtz Materials Corporation, through its operating subsidiaries, is a supplier of basic materials to the construction industry including crushed stone, ready mixed concrete, concrete masonry units and a wide range of precast and prestressed concrete products.

Jan 1, 1973

In the late 1980s and into the 1990s, the Mountain Pass Mine in California produced about 40 percent of the world?s rare earth elements. At the height of this production, the facility produced up to 54 L/s (850 gpm) of saltwater that was piped to offshore holding ponds where the water was evaporated. In 1998, following a series of waste water pipeline breaches, separations activities were suspended, reducing the Mountain Pass site to just the openpit mine and mill. The environmental concerns were addressed and the affected areas have since been remediated. However, in the years following the breaches, 97 percent of the world?s production of rare earth elements moved to China. By 2011, Molycorp, and the Mountain Pass Mine, had rebounded from the difficult times and were once again in a position to become a significant player in the rare earth industry.

Jan 1, 2011

By Chris Roos

The mining industry has made strides in planning for operations to be safe for the workforce and public, to protect the natural environment, and to maximize value for shareholders. However, many of the techniques used to accomplish these goals are based on estimated models of mineral content, production efficiency, and economic performance. The industry has begun to recognize the need for understanding the uncertainty in these models, how it affects their decisions, and what the potential impacts are for each project. The challenge has become how technical professionals can effectively communicate the impact of this uncertainty and its importance to both technical and non-technical audiences. This paper presents mining engineers (and other technical professionals) with traditional and modern principles of data visualization and technical communication that can assist with communicating the effects of uncertainty in the mine planning process.

Jun 25, 2023

By J. van Wijk

"Vertical material transport is one of the major challenges for the successful implementation of deep sea mining projects. The EU research project „Blue Mining” is focusing on sustainable solutions for deep sea mining operations, with one major goal being the advancement of Vertical Transport Systems (VTS). To investigate flow effects under realistic conditions, especially clogging effects, a 136 m high test facility for flow analysis in vertical transport has been constructed using available mining infrastructure. Tests are run in a closed circuit, using a system of downfall and riser pipelines connected to a compact sediment injection- and separation unit as well as the centrifugal pump. The riser is equipped with pressure sensors, as well as temperature sensors, flow meter, concentration meter and high speed camera to allow comprehensive analyses of the flow regime and behavior of transported material within the flow. Additional mobile measurement devices allow wear and tear analyses of pipe material. This paper focuses on the determining factors of the tests leading to the design as well as the installation and trial of the test facility itself and explains the used components and work principles. INTRODUCTION Since the 1970s several research projects had been conducted investigating in the possibility of deep sea mining. In recent times projects for deep sea mining operations have started again, considering the rising demand on natural resources, especially raw earth elements. Yet projects like the Nautilus project on the deposit Solwara 1 [1], or Japanese projects focusing on the region of Okinawa [2] and Chinese projects [3] planning on depths of “only” about 2,500 up to 3,000 m. Until now no economical deep sea mining project was realized, due to the enormous difficulties of deep sea environments. Vertical material transport is one of the major challenges for the successful implementation of deep sea mining projects, considering transportation heights up to 5 km. The EU research project „Blue Mining” is focusing on sustainable solutions for deep sea mining operations, with one major goal being the advancement of Vertical Transport Systems or VTS [4]. Critical parts of the system would be identified and investigated to deliver solutions and higher the technology readiness level to a level were planning of a pilot project can be considered. At first case examples for mining projects of seafloor massive sulfides (SMS, 1,600 m water depth) and manganese nodules (MnN, 5,000 m water depth) had been calculated on basis of economical frame conditions, such as planned production rates to be efficient. As depicted in Figure 1 two major possible systems had been used for comparison, airlift system and pump system, considering multiple pump stations or single pumps. Based on the results and comparisons for the calculated vertical transport systems critical components and flow effects had been identified."

Jan 1, 2018

By A. J. Basu

Computer assisted mine planning and design applications are routinely used by many Australian mining companies, However, the design process requires human expertise to recognize and evaluate the potential pitfalls. This paper introduces the application of a commercial optimization software (WHITTLE 4D) for strategic planning of an open pit mine in Western Australia. The authors present their experience in intelligent application of the optimization program while incorporating many technical and nontechnical obstacles. This paper provides some guidelines on how to apply the optimization software without loosing sight of practicalities. Moreover, this paper also shows how to build project evaluation guidelines for non-experts.

Jan 1, 1997

By Matthew Deutsch

A common casualty of modern openpit mine optimization is the assurance that the resulting design is actually achievable. Optimized mine plans that consider value and a bare minimum of precedence constraints do not, in general, translate into practical, operational mine designs that can be used in the field. Ultimate pits may come to a sharp point at the bottom. Schedules may require taking small parcels of material from many disparate areas of the pit in a single period, and grade control polygons may be ragged, narrow and not minable with realistic equipment. In this paper, these three fundamental openpit mine optimization problems are addressed by encoding them as maximum satisfiability problems. Maximum satisfiability provides a useful framework for problems that are nonlinear and may guarantee the optimality that metaheuristics cannot.

By Bianca Cruz, Tom Lankiewicz, Kent Sorenson, Karrie Radloff, Elizabeth Deyett, Dayal Saran, Michaeline Albright, Dan Stigers

Biology opens a new frontier for the mining industry. With rising environmental concerns, the need to couple conventional chemical and physical technologies with sustainable approaches is pressing. At Allonnia, we harness microbial processes to create innovative and environmentally responsible technologies with broad applications. The native microbial community (microbiome) remains largely unexplored at most mining sites, unlike the geochemical environment. The exploration of complex biological reactions that could transform mining technology is just starting and holds vast possibilities, spanning bio-cementation, carbon sequestration, ore beneficiation, water mitigation, bioleaching, metals recovery, and more. Allonnia has collected samples from mine sites in Australia, Africa, and North America to characterize the microbiome and uncover the genetic potential present in mineral-rich environments. We are evaluating microbial metabolites that selectively solubilize gangue from various ores. In addition, biological reactions hold promise as tailings stabilizers. Our early efforts illustrate exciting prospects for harnessing biology’s potential in mining.

Feb 1, 2024