Search Documents

By Steve Hicks, Zach Agioutantis, Greg Hasenfus, Zach Wedding

Most prediction methods used to calculate mining-induced subsidence rely on empirical formulations, which typically assume flat topography and uniform properties in the overburden. It is also well known that when a longwall panel mines below a valley bottom surface ground deformation magnitudes and orientations may be significantly influenced by the presence of the valley. This paper discusses ground deformation data collected at different surface locations above the Buchanan mine in the eastern United States. Measurements at individual surface points and strata movement measurements using a three-point extensometer have been collected as the area was undermined. Measurements correspond to the mining of the panel immediately under the measurement points and to the mining of adjacent panels. Measurement locations correspond to valley bottom locations. The measurements are critically evaluated and compared with respect to topography and panel face location. The issue of the fluctuation of GPS measurements is also discussed.

Jun 25, 2024

By Hsu-Hui Hsing

In several previous studies from this laboratory (1-4) the autophobicity concept of Zisman and co-workers (5, 6) has been extended to gas phase adsorption processes. Low molecular weight alcohols adsorb on silica or alumina to yield novel isotherms in that monolayer adsorption occurs at low relative pressures indicative of strong bonding, but subsequently multilayer adsorption is quite sparse and diminishes with molecular weight of the alcohol. Such isotherms fit no standard classification scheme, however, in the vacinity of monolayer coverage alcohol isotherms give an excellent fit to the Langmuir or B. E. T. , Type I model (7). Monolayer adsorption is relatively irreversible and it is thus possible to prepare these chemisorbed layers and perform subsequent adsorption studies thereon. All indications are that the adsorptive properties on such films is radically different from that on the underlying alumina (4, 8) and in one study finite contact angles for hydrocarbon fluids were observed. One perennial conceptual difficulty is that there is no observed upper bound to the adsorption isotherm which would be necessary for autophobic adsorption to occur. The cause for this has been studied, and it is currently believed that adsorption is complicated by reversible capillary condensation at contact points between powder particles. The evidence for this is that large particle powders give less "apparent" adsorption at high relative pressures and in one very tedious study adsorption on planar sheets, oxidized aluminum displayed similar reduced uptake at high relative pressures when compared with high specific surface area powders (3).

Jan 1, 1974

By Clarice L. Amaral, Ricardo Melamed

Clay-coating has been used as an environmental technology tool for the immobilization of toxic elements. The mechanisms of arsenate retention in clays suggest that not only the system pH is of fundamental importance in the process but also the character of metals and ligands that compose the electrolyte system. The goal of this study was to investigate the interactions between system pH and electrolyte ions on the retention of arsenate in an Oxisol soil. The sorption of arsenate decreases with the increase in system pH, reflecting the competitive sorption of arsenate with OH groups. Solutions containing Ca tend to favour the immobilization of arsenate in a relatively broad pH range.

Jan 1, 1998

By D. D. Misra

Though computer simulation of coal beneficiation has been in use for nearly two decades the models used in the programs for the simulation of the crushing processes concentrate mainly on the size distribution. This paper suggests the use of an empirical equation approximating to the cumulative probability or error function for the simulation of the liberation process in coal crushing. The algorithm outlined here can be incorporated in a computer program already having a size distribution model.

Jan 1, 1989

By K. A. Natarajan, K. S. N. Murthy

Growth of Thiobacillus ferrooxidans on pyrite mineral surfaces and in 9K leach media was studied through estimation of bacterial protein in the different phases. Bacterial attachment was found to be governed by particle size of the mineral, period of incubation and by stationary or agitation conditions used during incubation. Increased bacterial growth in the liquid as well as on the solid phase was observed with decreasing particle size and increasing incubation periods. Increased bacterial attachment to pyrite mineral surfaces was observed to promote iron dissolution.

Jan 1, 1993

By Frederick W. Bauer

The potential worldwide "market" for metallurgical bauxite is about 94 million MT. The high degree of concentration of the alumina sector, combined with the high percentage of long-term contractual relationships, results in a small spot market with an illdefined price structure. Further segmentation occurs based on bauxite quality and alumina plant design. The potential 'free" market is estimated to be about 18 million MT that represent the requirements of nonintegrated alumina producers. It, too, is covered almost entirely by multi-year supply contracts.

Jan 1, 1984

By A. W. Jenike

Mine backfilling is a desirable method for the disposal of retorted oil shale. Hydraulic, mechanical and pneuna.cic transport and stowing methods were investigated, and the mechanical transport and stowing method using conveyors was selected as the most promising system. Transport of retorted oil shale at the rate of 3000 cons per hour (2700 t(h) to the backfill level, situated about: 2000 feet (610 m) below surface, with skips or conveyors is uneconomic. Hence, borehole transport utilizing gravity flow was investigated. This paper describes the theory of flow, flow properties of retorted oil shale, and the design of a borehole and hopper system.

Jan 1, 1978

By K. A. Natarajan, M. K. Yelloji Rao

Significance of grinding media wear and its effect on chalcopyrite flotation are discussed. Laboratory marked ball wear tests were conducted grinding chalcopyrite ore and quartzite dry, wet, and with collector added during grinding. The effects of oxygen and nitrogen on ball wear were evaluated by the addition of chalcopyrite mineral while grinding quartzite. The effect of dry and wet grinding on chalcopyrite flotation was also studied. Results show abrasive wear is greater in quartzite grinding than in grinding chalcopyrite. Oxygen increases the corrosive wear of high carbon low alloy steel balls in the presence of chalcopyrite ore. Chalcopyrite flotation was retarded due to wet grinding in the presence of oxygen. Though collector reagent increased the media wear, it improved the flotation of chalcopyrite. Probable electrochemical reactions encountered in a grinding mill are outlined.

Jan 1, 1991

By Paul Saxton

INTRODUCTION AND SUMMARY This short paper deals with the history of the Nickel Plate Mine from 1898 to 1987, with the major focus on the time period 1984 to 1987. Operations from 1898 to 1955 are reviewed in a cursory manner with the emphasis on some interesting points in the early 20th century. A review of the major exploration work carried out in 1984 to 1987 is presented and the process of moving the project through feasibility, government permitting and construction is described. The Hedley gold camp is situated approximately 40 kilometres east-southeast of Princeton, in southern British Columbia. The area has had a long history of gold mining and between 1902 and 1955 approximately 1.5 million ounces of gold were won from several mineralized skarn orebodies. Most production came from the Nickel Plate and Hedley Mascot mines. AN EARLY TO MID 20TH CENTURY SUMMARY The Nickel Plate is one of the oldest mines in the province. The mine had operated from 1904 to 1930 and, after a period of shutdown, from 1934 to 1955. The mine was revived in 1967 for exploration and. will resume production during the first half of 1987. In the first period the Yale Mining Company and Daly Reduction Company operated for six years and Hedley Gold Mining Company for twenty-one. In the second period the mine was operated by the Kelowna Exploration Company Limited and Kelowna Mines Hedley Limited for twenty-one years. In the present period the mine has been revived by Mascot Gold Mines Limited.

Jan 1, 1987

By Robert E. Ennis

The somewhat misnomered "continuous" face section is in most mines today still far from perfect continuity. Achieving uninterrupted flow of coal from the mining machine to the outside has been a long sought for goal. Clearly, the largest problem to be solved in continuous mining today is one of increasing the cutting time of the miner. Full machine utilization can never be achieved with the new high capacity miners, as long as their performance is tied to that of the shuttle car. Figure No. I illustrates the point at which shuttle car haulage distance determines unit productivity rather than the productive capacity of the miner. Continuous mining is never realized. A recent development has proven, however, that truly continuous mining and haulage is possible. The Bell & Zoller Coal Company working with the Research and Development Department of Hewitt-Robins Inc. developed and perfected a new mining system which offers advantages in terms of increased productivity at reduced mining costs and enhances the safety of personnel at the face. This new system involves the use of two pieces of equipment that form a unbroken link, at all times, between the mining machine and the mine belt haulage system. These pieces are a Mobile Bridge Conveyor, and an extensible panel conveyor. The following areas of discussion will be covered during the review of this development. I. The design and operating features of the new system. 2. Its application in underground mining 3. The performance of the system to date 4. Operation and maintenance cost considerations 5. Safety features of the system

Jan 1, 1965

By M. E. Lewellyn

A new class of thionocarbamates, O-alkyl-N-allyl thionocarbamate (III), has been found to give better metallurgy than 0-isopropyl-N-ethyl thionocarbamate (I) for a number of sulfide ores containing copper, lead, and zinc. Data on the results of flotation tests with several such ores are presented. The improved metallurgy is believed to be due to the participation of the allyl double bond in the complex formation of the thionocarbamate on the surface of the mineral.

Jan 1, 1985

By Dennis A. Beiter, Kenneth G. Fields, Richard T. Stoltz

Section 56.5001 Title 30, [Code of Federal Regulations1], establishes requirements for respirable dust exposure in Metal and Nonmetal Mines based on the Threshold Limit Values (TLV's) adopted by the American Conference of Governmental Industrial Hygienists. Respirable dust samples collected by Mine Safety and Health Administration (MSHA) inspectors at a sandstone quarry showed certain workers were exposed to excessive concentrations during development of a "coyote tunnel" that was ventilated with a blowing system. Because exhausting face ventilation systems are known to control dust more effectively than blowing face systems, a change was proposed to improve worker respirable dust exposures. This paper describes the evaluation of the proposed exhausting ventilation system in the quarry's "coyote tunnel" and compares the respirable dust exposures with those measured by the MSHA inspectors with the blowing system. Results showed the proposed exhausting ventilation system reduced respirable dust exposures to less than 20 percent of those measured by MSHA inspectors when the blowing system was used.

Jan 1, 1993

By Brian Hester

Many Third World African countries are well-endowed with minerals - especially gold and diamonds - while only a few have important base metal deposits. For decades since colonial rule, political and economic conditions discouraged interest by Western capital. Influence from Soviet Bloc countries, however, has declined with the move toward multi-party rule. And the left wing orientation, once widely favored by Third World African countries, has almost disappeared. With International Monetary Fund (IMF) encouragement, these Third World African countries now encourage representational government and solicit western finance to expand their industries. Mining is especially encouraged. The North American mining industry is following the same trail as other capital intensive industries and looking abroad for opportunities. The Prospectors and Developers Association of Canada released figures that show exploration expenditures in that country were halved between 1987 and 1990. Figures for the United States are not so easily found but every indication points to a downward trend. While total annual expenditures on US exploration by corporations as a group are either declining or remaining constant, expenditures away from North America is increasing. Gold exploration expenditures in 1991 by the major companies tracked by Minerals Economics Group were less in the United States than for Latin America and the Southwest Pacific combined. The same study showed as much was spent in the Republic of South Africa and "Other" areas combined as in the United States. Expenditures by major corporations in these "Other" areas amount to only 5.2% of their total budget. Third World Africa is a major component of these "Other" areas.

Jan 1, 1993

By David G. Hammond

INTRODUCTION Previous papers and discussions at this conference have already covered the subjects of identification and nature of risks, allocation of risks and contractual arrangements. In this portion of the conference, in the light of topics already covered, we will consider how to minimize risks and how to mitigate losses. Webster defines mitigate as "to make less severe or painful", an apt definition for our purpose! RISK MANAGEMENT POLICY The first thing that must be said about risks, especially in construction, is that they exist and that they don't necessarily fall alike on the just and the unjust. Some risks, i.e., some kinds of risks, must be recognized as inevitable in engineering and construction and therefore must philosophically and realistically be accepted as part of situations to be dealt with. Dealing with means minimizing, covering, and sharing of risks and doesn't mean merely passing off the risks to someone else. While some risks can be avoided, for example, whether the structure will fall down or the excavation will cave in, risks management primarily deals with: A. minimizing risks---whomever risk it may be B. equitable sharing of those risks among the participants.

Jan 1, 1979

By Fred H. Seymour

In spite of the progress made by geostatistical theory over the years, evaluation of low grade open pit gold deposits continues to be challenging. Many Carlin type deposits are modelled from exploration drilling spaced on 10C foot centers. From these drill holes, 50 by 50 by 20 foot blocks containing about 4000 tons of material are estimated. The block size is a compromise between being large enough for a good geostatistical estimation and being small enough for practical pit limit analysis and mine planning. Most of these gold deposits are highly variable and include ore and waste zones that are too small to be properly defined from exploration drilling information. Because of this, selective mining is controlled by sampling closely spaced blast holes where the density can be as high as 50 blast holes per exploration drill hole intercept. Figure 1 illustrates an example of the ore/waste contact definition before and after blast hole sampling. With exploration information only, a tentative ore/waste contact can be drawn between the exploration blocks.

Jan 1, 1989

By Chris J. Conway, Bruce W. Atkinson, Graeme J. Jameson

The flotation of coal in the fie and coarse particle size ranges presents particular problems. Fine or ultra-fine coal less than 100 microns presents a challenge to conventional flotation machines because the rate of capture of the coal particles can be very low, so longer residence times are needed. Also, conventional mechanical cells are not normally designed with froth properties in mind. Froth drainage may be inadequate, leading to excessive entrainment of ash. The upper limit of flotation of coal is normally put at about 500 um (30 mesh). It appears that, in mechanical cells, coarser particles tend to be torn away from bubbles in the turbulent environment created by the impeller. In this paper, results are presented from plant trials of a high-intensity flotation column of novel design, namely the Jameson cell. Extensive trials have been conducted on coal slurries with a top size of around 1 mm. Size-by size analysis shows that it is possible to achieve high yields of low ash product over the whole particle size range.

Jan 1, 1995

By R. C. Schmidt

The Mont Klahoyo magnetite deposit is located about 600 km northwest of Abidjan, Ivory Coast. During an exploration period ending in 1977 an international joint venture group investigated the deposit and proved reserves of 670 million tons grading 36% iron. The deposit, occurring at the northeast end of the Baoubly-Kiriao chain of Precambrian iron formations, is associated with amphibolites, pyroxenites and gneisses of the Liberian Shield. At Mont Klahoyo occur two separate iron formations of which the lower member is the ore body. This lower member consists of a highly metamorphosed - banded quartz-magnetite iron formation in which iron silicate bands alternate with beds of quartz-magnetite. mphibolite-pyroxenites and sillimanite-cordierite-garnet gneisses form hanging and footwall rocks. The iron formation has been folded into an elongated overturned "Z" shaped major drag fold with axes trending and plunging approximately northeast. Beds are vertical or dip steeply to the southeast. The ore zone has an average thickness of 130 m and outcrops intermittently over a distance of approximately 5.5 km. Based upon detailed studies of drill cores and the results of ore dressing test work, eight stratigraphic units, identified as K-1 to K-8, are recognizable in the iron formation. Four interbedded units are low grade silicate zones (silicate facies) with the remaining quartz-magnetite units (oxide facies) repre¬senting the important ore zones of the Mont Klahoyo deposit. The ore-bearing "K" units are subdivided further, based upon their specific lithologies, iron content and concentration characteristics, into eleven ore types. The identification of these ore types is considered particularly important to mine planning and flowsheet design. A cap of oxidized materials overlies the primary quartz-magnetite iron formation but no enrichment has occurred. It is proposed that the Mont Kalhoyo iron formations were deposited, possibly chemically, in a volcanic environment as a siliceous iron formation with volcanism providing the primary source of iron and silica. Metamorphism converted the siliceous iron formation to a relatively coarse-grained quartz-magnetite-silicate iron formation.

Jan 1, 1979

By J. P. Earnhardt

Recycling of such municipal solid wastes as glass containers, metal cans, and newspapers has received increasing attention recently. However, municipal solid wastes account for only 1% of the total solid waste stream in the United States. The remainder includes hazardous and non-hazardous industrial wastes. Generators of industrial wastes are facing higher landfill costs. Future liability potential, and public image concerns which are forcing them to seek innovative and often profitable solutions to minimize, reuse, and recycle their waste streams. Opportunities for the mining industry in industrial recycling include recovery of mining wastes and by-products, and utilization of mineral products for treating waste streams.

Jan 1, 1993

By Charles E. Joachim

Current Army tunnel destruction criteria (1) are based on limited nuclear-explosive (NE) and high-explosive (HE) test data. The PILE DRIVER (2) and HARDHAT (3) events investigated tunnel and support system response where yields were relatively large and tunnel diameter small compared to typical underground openings and localized stress fields of low yield weapons. Some limited tunnel destruction information was obtained from underground events of the PLUMBBOB and HARDTACK II Series (4). These events used access drifts which were designed to be self closing at the weapon point. The limited NE data are augmented by HE results from the Underground Explosion Test (UET) Program, a series of model and prototype-scale experiments in granite and sandstone (5). Weapon standoff distances (charge c.g. to tunnel wall) were at or near the maximum for major damage. Limited tunnel destruction was produced by a series of hasty and deliberate tests (6) on abandoned railroad tunnels in basalt. Additional HE data were obtained from model tests at the Waterways Experiment Station (WES) (7) using 2.1 MJ (2 lb) TNT charges and tunnel diameters varying from 3 to 17 cm (1.2 to 6.6 in). Recent laboratory scale HE experiments (8) conducted at the WES under the ESSEX program investigated the effects of tunnel diameter, standoff distance, charge confinement, material strength and to a limited extent, tunnel spacing and liner strength variations on tunnel damage. This paper summarizes the analysis conducted to develop predictions for the effects of low-yield nuclear weapons against tunnels and underground openings in rock.

Jan 1, 1979

By P. S. Parobeck, T. F. Tomb, R. S. Ondry

From October 1980 through August 1982, surveys were conducted on 19 longwall mining operations to obtain data relative to respirable dust levels associated with particular longwall operations and occupations, to make recommendations for enhancing dust control, and, where applicable, to evaluate the effectiveness of new technology implemented to control dust. The paper summarizes the data collected during these surveys and, where possible, draws conclusions and discusses actions that can be utilized to reduce exposures to respirable coal mine dust on longwall mining operations.

Jan 1, 1987