Search Documents

By H. I. Meyer

The mine is a large open-pit copper mine located near Tucson, AZ. Mining operations involve shovels digging at relatively fixed locations and haul trucks moving the muck to a primary ore crusher, a primary waste crusher, and directly to waste dumps. The total investment in shovels and trucks is some $100 million. Fig. l is a schematic drawing of the operation. A static method of truck assignment is used; i.e., each driver is given one particular shovel to serve until reassigned by the dispatcher. A dynamic system is one where trucks are reassigned after each trip. The problem is to compute a near optimum assignment of trucks for efficient operation.

Jan 1, 1979

By Chris Howell

PotashCorp?s Aurora phosphate mine, in Beaufort County, NC, operates four low pressure boilers and four high pressure boilers to meet its process steam requirements. Maintaining these boilers is critical to meeting production demands. Processing phosphate ore into phosphoric acid requires large amounts of sulfuric acid and steam. Ore is mined from the phosphate deposit with large bucket excavators after 9 to 30 m (30 to 100 ft) of overburden is removed. The phosphate ore is mixed with water to make a slurry that is pumped to the mill. Elemental sulfur is burned in the presence of air to make sulfuric acid. This process is highly exothermic and boilers produce steam while cooling the process. The phosphate ore is reacted with sulfuric acid and the resulting products are refined into different grades of phosphoric acid for fertilizers, feed stock and food additives. Plant operators at the mine were challenged with boiler feed water that was high in silica and other contaminants. As a result, boiler operations were experiencing difficult, labor-intensive operations and equipment deterioration. This resulted in higher operating costs and diminished processing performance. The facility was operating an aged boiler feedwater pretreatment system that included warm lime softening followed by pressure filtration and a cation/anion/mixed bed demineralizer system. The demineralizer required frequent regeneration and chemical usage was high and costs were difficult to predict. Depressurized well water (DPW water), used for plant utility water and boiler makeup, is very high in silica, in the range of 60-70 ppm. Silica can form scale at pressures below 600 psig. Above 600 psig, silica starts to volatize, carrying over with steam to potentially form deposits on downstream equipment and processes. Mine officials decided to upgrade the boiler feedwater pretreatment system to a state-of-the-art reverse osmosis (RO) membrane system. This new system, which started up in March 2009, has improved operating performance and reduced water consumption and overall operating expenditures.

Jan 1, 2011

By RALPH BALTES, AMIR EHSAN KIANFAR, FABIAN UTH, ELISABETH CLAUSEN

  Underground positioning and communication are essential technologies for the future of underground mining operations. In contrast to other positioning and communication technologies such as wireless local area network (WLAN) or radio frequency identification (RFID), ultra-wideband (UWB) radio technology provides significant benefits like accurate and robust positioning of mobile machine equipment, which is indispensable for future autonomous systems in underground mining processes, such as production, transportation and auxiliary operations. Among these technologies, UWB offers many advantages, including higher accuracy, robustness, resistance against noise and multipath effects, and low power consumption [1,2]. Underground automation and localization systems benefit from these advantages and use the technology to improve efficiency and safety. There are many studies being carried out on this technology to increase the results’ accuracy, energy sufficiency and more. Two robust UWB modules that were developed for underground positioning and collision avoidance with regard to human safety in underground mining operations are introduced. The measurement results of tests carried out in an underground mine are discussed as well to confirm the functionality of the system.

By Robert E. Murray

The title of my paper, "A Company's Response to Federal Coal Leasing," brings to mind a picture of a dog chasing its tail. This is what the coal industry, has been doing since the Federal coal leasing moratorium went into effect in 1971. We've gone around in many circles, but we are only very slowly, if at all, getting closer to catching our tails, i.e., efficient, economical, and rational Federal coal leasing. My companies, The North American Coal Corporation and its four Subsidiaries, The Falkirk and Western Plains Mining Companies and The Coteau and Missouri Valley Properties Companies, together hold in excess of 4.5 billion tons of lignite reserves in North Dakota. Some of our North Dakota properties are substantially interspersed with Federal coal, with the government holding title to the minerals in every other section. This checkerboard pattern of Federal ownership has made it difficult to develop and market some of our reserves, and, as a result, it has become imperative that we be familiar with and active in the Federal Coal Leasing Program.

Jan 1, 1982

By A. ALLANORE, OLIVEIRA M. DE, D. CICERI, D. P. CHEN

The alkaline hydrothermal processing of K-feldspar rocks in an autoclave can be a pathway to synthesize a potassium fertilizer for tropical soils that is potentially cheaper and more efficient than traditional potash (KCl). When K-feldspar undergoes hydrothermal alteration in the presence of calcium oxide (CaO), it generates a complex mixture of calcium-aluminum-silicate-hydrate (CASH) minerals that incorporate K atoms stochastically in their structure. These atoms are subsequently released, as shown in a test-tube leaching test, indicating a possible uptake by crops. The relationship between the processing temperature and time in the autoclave for the hydrothermal reaction and the resulting mineralogy and elemental release are only partially understood and are investigated in this study. Elucidating that relationship is the key requisite for subsequent techno-economic analysis, and ultimately for the development of a fertilizer that can be considered as a feasible alternative to KCl.

By David F. Becker

Two-dimensional, finite-difference elastic modeling aids in planning an optimum seismic-acquisition scheme to define the extent of subsurface cavities resulting from in situ gasification. To understand the seismic effects of a cavity, two models are compared and contrasted. Model A consists of a low-velocity layer (LVL) in a half space; Model B contains a rectangular water-filled cavity in the LVL. Amplitude differences are the dominant effect on the surface records for each model. Cavity resonance and diffraction effects are more definitive in vertical seismic profiles (VSP's) and in a "snapshot" of the wave field. Interpretation and subtraction of corresponding records for both models shows the need for pre- and post-gasification seismic recording. Also VSP data are more informative than surface records.

Jan 1, 1983

By C. Einberger

Groundwater Monitoring is typically required by regulatory agencies at potentially hazardous landfills or surface impoundments. Agencies have often required an arbitrary number of wells with limited evaluation of the effectiveness of the network to detect a leak. A Monitoring Efficiency Model (MEMO) has been developed to improve the design and cost effectiveness of monitoring well networks. MEMO 15 an analytical model that simulates the migration of hypothetical contaminant plumes from a site and quantifies the efficiency of alternative well network designs in detecting the plumes. The computed monitoring efficiency provides a quantitative measure of the well network adequacy based on hydrogeologic considerations. The model was recently used to design the groundwater monitoring well network for a heap leach pad at the proposed Beartrack Project.

Jan 1, 1993

By Gerald W. Cormick

In a complex society such as ours, the range of "negotiating" relationships is constantly increasing. These negotiating relationships have emerged as a direct result of the diffusion of power or influence to new sectors and emerging concerns. Even within organizations, the myth of the authority-based heirarchical structure has given way to the reality of constant negotiations between superior and subordinate and with peers in the organizational structure. In the broader context, the corporate organization finds it necessary to reckon and often negotiate with organized employees, suppliers, buyers, government agencies and a range of organized private interests ranging from minority groups to environmental organizations. In response to this diffusion of power and the conflicts which it has engendered, a variety of conflict avoidance, conflict managing or conflict resolution techniques has developed. The purpose of this paper is to attempt to differentiate between some of the conflict intervention approaches which have appeared "on the market", and to suggest three bases for selecting among them: 1. The "role" of the conflict intervenor; 2. How far the conflict has developed; and 3. The breadth and impact of the issues involved.

Jan 1, 1979

By Qinghua Tian, Zhipeng Xu, Dong Li, Xueyi Guo, Liu Zhu

Tellurium (Te) is an important scattered metal. Known as the vitamin of modern industry, national defense and cutting-edge technology, it is the supporting material for new high-technology materials. Currently, its separation and extraction from Te-bearing materials face problems such as long flowsheets and high reagent consumption, giving rise to an urgent need to develop new methods for its recovery.

By M. B. Daza, B. Lattimer

"Even with modern detection and firefighting techniques, mine fires continue to be a safety concern. However, some underground mine fires can be addressed with the remote application of high expansion foam, reducing firefighter exposure to hazards. The flow of this foam can be numerically or computationally simulated in order to gain a better understanding of its behavior, but rheology parameters are needed as inputs to produce accurate simulations. For this reason, this work studies the rheology of firefighting high expansion foam using a foam generator and Poiseuille –Flow Rheometer. Rheological parameters for foams with expansion ratios between 250-1280 are represented by the consistency index (k) and the power law index (n) due to the results show a strong agreement with the Power Law model for non-Newtonian fluid viscosity. Furthermore, experimental results show that high expansion foam behaves as a shear thinning fluid with a power law index around 0.4 and viscosities in the range of s 0.1 Pa-s and 0.042 Pa-s under shear rates between 44 ??-1 and 187.3 ??-1. INTRODUCTION High expansion foams are called to foams with expansion ratio greater than 200. Expansion ratio (??) is defined as the ratio between the volume of foam produced (i.e. volume of foam solution and volume of gas) and the volume of foam solution used (NFPA 2014). Because of its high expansion ratio, one of the most important application of high expansion foams is to fill or flood large spaces such as hangars, storage facilities and underground mines for fire suppression. The foam can fill large structures using small quantities of foam solution within a short time (Sthamer 2012) (Martin 2012). Although the specific high expansion fire suppression mechanism has not been understood on a quantitative basis, a possible mechanism is fuel isolation when the foam act as a physical barrier between oxygen and the flame. Furthermore, as a consequence of this contact water is evaporated, causing cooling of fuel and surrounding air. Besides, water vapor as product of water evaporation causes a dilution of oxygen concentration available to the fire (Fleming and Sheinson 2012). High expansion foam can be applied remotely by means of conduit pipes or in situ close to the fire. In most of the underground mines scenarios, fires have to be addressed remotely to reduce miner and firefighter exposure to the hazards (Smith et al. 2005). Although high expansion foams should not be blasted and must be deposited directly on the area of application because of their low density (Harding et al. 2016) sometimes it is complicated to apply it directly to the fire due to complex access areas at underground mines. In these cases, foam has to be applied far away from the fire. Despite of this fact there is a lack of knowledge in terms of rheological behavior of high expansion foam under high shear rates (Gardiner, Dlugogorski, and Jameson 1998). Furthermore, there are a few attempts to simulate numerically the high expansion foam flow due to the ignorance of its rheological parameters and its complex behavior. (Weaire 2008)."

Jan 1, 2018

By H. S. Ten Eyck

The major underlying threat to man's successful survival and happy existence on this planet is our own prolification. This poses an even greater threat to the future of civilization than continued wars and even "The Bomb" itself. Just the predictions of the world's population trend are awesome and demand our serious thought. This trend has been given the now well-known term, "The Population Explosion" - and this is literally what is taking place throughout most of the countries around the globe. Today, the world's resources support approximately 3.3 billion people. Based on the present world population growth rate of 2.1 percent, there will be another 65, million just one year from today. Such an increase in one year means that the world will add a greater population than that of Mexico and Canada combined. Projecting at this remarkable, but unchecked, growth rate, 6.7 billion people will be competing for survival by the end of this century.

Jan 1, 1966

By Cheryl Lee Vatter

The Lupin mine consists of a gold mining, milling, and refining complex located 400 km (250 miles) northeast of Yellowknife and 100 km (60 miles) south of the Arctic Circle on the southwest shore of Contwoyto Lake in Canada's Northwest Territories. (Fig.1). The mine was commissioned in 1982 and is presently producing 6 t/a (193,000 oz per year) of gold from 612 kt (675,000 st) of ore. The success of this operation is due to such factors as the continuity and grade of the ore body, the competency of the host rock, low mining costs, efficient milling, the transportation of people and materials to and from the mine site, and the unique work schedule resulting in a stable workforce. Echo Bay Mines operated a silver mine at Port Radium on Great Bear Lake, Northwest Territories, from 1965 to 1982. The company first obtained an option on the Lupin property from Inco in February 1979 and completed an underground exploration program in 1979-1980. Topographic relief is low and vegetation is sparse in the continental subarctic climatic zone, consisting mainly of moss and lichens. Temperature extremes are from 24°C to - 45°C (+75°F to -49°F) with an annual mean of -12°C (+54°F). Permafrost extends from near surface to 500 m (1640 ft) in the ore zone. Its remote location and harsh climate presented some challenging design and logistical problems. Construction began at the Lupin mine site in 1980. Before construction, a 1.5-km (5000-ft) gravel landing strip was prepared, suitable for landing a C 130 Hercules. The entire Lupin project took 20 months to build. All of the men and materials were transported to the site with some 1100 Hercules flights and several hundred Convair 640 flights. The Convairs transported construction crews, which numbered 400 at their peak, and also carried 3.2 kt (3535 st) of supplies during construction. The facilities were constructed and commissioned for a total cost of C$135 million. The operation was originally designed to throughput 860 t/d (950 stpd). Expansion in 1983, circuit refinements, and some capital projects brought the daily throughput to 1.7 kt/d (1850 stpd). The underground mine delivers 612 kt/a (675,000 stpy) of ore to the mill at an average head grade of 8.46 g/t (0.3 oz per st). The ore is nonrefractory and is processed in a conventional cyanide leach using the Merrill Crowe process. Gold recovery is about 95.0%. The average production cost is $US5.85/g ($US 182 per oz) based on 1987 figures. Mining at Lupin – Geology The Lupin deposit occurs in amphibolite grade iron formation overlain by mudstones (phyllites) and underlain by graywacke (quartzites). Contacts between the wallrock units and the iron formation are well defined. It has been folded and tilted into a megascopic antiform-synform-antiform structure (Fig. 2). Gold occurs primarily within the sulfide rich iron formation, with some minor occurrences in sulfide poor iron formation. The distinction between sulfide rich and sulfide poor iron formation is based on a visual cutoff of 5% total sulfide content. Mining widths are determined by an assay cutoff of 4.2 g/t (0.15 oz per st) gold. There are few tons between 1.7 and 4.2 g/t (0.06 and 0.15 oz per st). The amphibolitic iron formation at the mine ranges from 1.5 to 20 m (5 to 65 ft) wide and has been followed over a strike length exceeding 1.7 km (5600 ft). The wider portions of the ore body tend to occur at its north extent and south nose. The gold-bearing iron formation appears on plan as a Z-shaped structure made up of three zones: the West, Center, and East. The West and Center zones dip steeply to the East (75° to 90°). Each of the ore zones plunge at an angle of about 65°. Total strike length of the three zones is more than 610 m (2000 ft). The zones are confirmed at a depth of 650 m (2130 ft) below surface. The Center zone is the widest and varies from 4.5 to 20 m (15 to 65 ft) while the West is the narrowest, averaging 1.5 m ( 5 ft). The footwall is comprised of quartzites that are strongly jointed and locally grades into phyllite, which comprises the hanging wall. The hanging wall and footwall are reversed in the West zone. Mineralogy of the ore at Lupin consists of amphibole minerals (hornblende, cummingtonite, and grunerite), feldspars, quartz, occasionally garnet, pyrrhotite, arsenopyrite, minor pyrite, and trace chalcopyrite. Also found in minor amounts are scheelite, apatite, epidote, calcite, tourmaline, and some arsenides (notable loellingite). Quartz

Jan 1, 1989

By K. N. Mayfield, T. Novak

"The applications for automation continue to expand within the mining industry. These applications can range from the startup, control, and shutdown of processing plants to the autonomous operation of surface haulage trucks. However, the term “automation” should not necessarily be interpreted as the total elimination of human interventions since numerous mining processes can be partially automated. The future survivability of many mining operations will be influenced by a company’s willingness and ability to understand, accept, and utilize this technology. The mining workforce, including management and engineering, should be familiar with the technological capabilities and limitations for effectively implementing automation into mines for improving safety and productivity. The Department of Mining Engineering at the University of Kentucky has recognized this educational gap and developed an automation laboratory, along with project-oriented courses at the undergraduate and graduate levels. The laboratory and the course objectives are described in this paper, as well as the skills and abilities that students obtain at the completion of the course(s). BACKGROUND The touted benefits of automation include: improved productivity, lower operating costs, reduced drudgery of repetitive operations performed by workers, and the removal of workers from hazardous locations. The acceptance of advanced technology by the mining industry, however, has traditionally been slow. This cautious approach is understandable considering the complex and harsh conditions routinely encountered in mining operations. Bad experiences with some premature installations of newly hyped technologies may have also resulted in lingering skepticism by many mine operators. Nonetheless, with thoroughly demonstrated reliability and proven applications, automation based on programmable logic controllers (PLCs) has made significant inroads into the mining industry. Programmable logic controllers (PLCs) are the workhorses of automation. They were originally conceived in the late 1960s, long before the invention of the personal computer (PC). Initial PLC applications were directed towards sequential relay control in manufacturing plants, which subsequently eliminated the use of “relay logic” that was based on hard-wired electromechanical relays. With continuous advancements in electronics and computer technology over the years, PLCs have evolved into sophisticated and powerful devices with very stable operating systems. They are designed for deterministic logic execution with extreme consistency in timing, along with a high tolerance to temperature, humidity, and vibration (Smith 2003). Because of their robust characteristics, PLC networks now provide the backbone for most industrial automation applications."

Jan 1, 2017

By A. Cartwright, J. Cardwell

"Complex geology requires innovative approaches to confidently and appropriately model grade and geologic trends. Local Anisotropy Kriging (LAK), by Isaaks and Company, and MineSight® Dynamic Unfolding (MSDU) from Hexagon Mining are advanced interpolation methods designed to best estimate grade along deformed three-dimensional grade trends at sediment-hosted deposits. While LAK works in Euclidean space for the construction of variograms, kriging weight assignment, and non-linear local interpolation search ellipsoids, MSDU is far more dynamic and can utilize a modeled three-dimensional undulating surface representing a folded grade trend to construct the above mentioned. MSDU was implemented at the sediment-hosted, stratabound Tenke-Fungurume mining district and revealed major block-to-block differences in interpolated copper and cobalt grades compared to LAK. INTRODUCTION Grade estimation is the cornerstone of long-range mine planning. Pit designs, metal recovery, mining costs, reserves calculations and reporting are all dependent upon a reliable grade model. If the geology is poorly understood or the interpolation methods and parameters have been haphazardly constructed, then massive financial losses will be the inevitable outcome. Therefore, a properly trained geologist must use all of the appropriate tools available including deposit knowledge and advances in modeling technology to construct the most geostatistically and practically sound long-range block model. Certain deposits, such as the sediment-hosted deposits at Tenke-Fungurume, require an interpolation method that best suites the style of mineralization. In 2014, Hexagon Mining developed a tool in MineSight called dynamic unfolding (MSDU) that has the potential to improve upon previous Euclidean-based interpolation methods. MSDU utilizes the non-stationarity of a folded grade trend to more accurately construct variograms and improve interpolation results based upon a modeled three-dimensional surface. Geology Overview The sediment-hosted Tenke-Fungurume mining district is located in the southeastern part of the Democratic Republic of the Congo (Figure 1). The rocks within the district are primarily dolomites and shales from the lower half of the Roan Supergroup that were mineralized by ascending pregnant copper and cobalt rich brines within a massive sedimentary basin (Cailteux et al., 2005) (Figure 2). These oxidized brines likely found a fluid channel in the porous RSC unit. The surrounding rock units provided a redox boundary for copper and cobalt precipitation along organic rich beds, forming a massive stratabound deposit that was later broken up by several subsequent tectonic events (Dewaele et al., 2006). Layering and Block Orientations To capture the bedding-controlled nature of the Tenke-Fungurume copper and cobalt mineralization, each lithology type must be subdivided into individual layers with a uniform thickness (Figure 3). The thickness of each layer is determined by the user, but should equal the bench height to achieve maximum resolution within each lithology type. Composites are back coded from the model to achieve layer codes that match block locations."

Jan 1, 2016

By R. L. De G. Solms

INDEX 1. INTRODUCTION 2. FLOODING 3. THE PLUG 4. THE FIRST ATTEMPT 5. THE SECOND ATTEMPT 6. PUMPING 7. TIGHTENING OF THE PLUG 8. SHAFT REPAIRS 9. POST-MORTEM 10. CONCLUSION

Jan 1, 1987

The Carlin Trend is North America's premier gold producing district. It is located in northeastern Nevada's Elko and Eureka Counties along a northwest trending belt about 65 km (40 miles) long and 8 km (5 miles) wide (Thorstad, 1989; Jones, 1989). This trend is the worldwide reference site for epithermal, sedimentary rock-hosted microscopic gold deposits. At least 19 deposits have been discovered to date, varying in size from 933 kg to 1.08 kt (30,000 to 35 million contained oz) of gold (Fig. 1). Newmont Gold Co. and its parent, Newmont Mining Corp., jointly constitute the largest mineral right holders in the district. They own or control more than 1000 km'- (386 sq miles) in and around the Carlin Trend and own all or part of 16 out of the 19 mines and prospects identified to date. Since the initiation of Newmont's exploration activities in the Carlin Trend in 1961, 2.24 kt (72 million oz) of cumulative gold resources have been identified. Cumulative production from all mines since the start-up of Newmont's Carlin mine in 1965 to the end of 1989 was about 202 t (6.5 million oz) (Jones, 1989). The incentive of sustained high gold prices and innovation in processing technology resulted in a significant acceleration of gold output over the last few years. Newmont Gold alone produced more than 43.5 t (1.4 million oz) in 1989. That is equal to 22% of the cumulative 1965 to 1988 output, and an almost 200% increase over its 1986 output.

Jan 1, 1991

By D. J. McCracken

The lithium review did not arrive in time for publication in the June issue The estimated consumption of lithium minerals as raw materials to the glass, ceramic and metallurgical industries in 1992 was 85.5 kt (94,200 st). That equates to about 12 kt (13,200 st) of lithium carbonate equivalent (LCE). An additional 150 kt to 200 kt (165,000 to 220,000 st), or 7.5 kt to 10 kt (8200 to 1100 st LCE), were used in the production of lithium chemicals. The 1992 consumption represents an overall decrease of 3.5 kt (3800 st), or 500 t (550 st) LCE, from 1991. This was a direct result of a worldwide reduction in glass demand due to the economic recession. There are three major producers of lithium minerals. Gwalia Consolidated Ltd. (formerly Lithium Australia Ltd.) in Western Australia and Tantalum Mining Corp. (Tanco) in Manitoba, Canada, both produce spodumene ore. Bikita Minerals, in Zimbabwe, is the largest producer of petalite. Bikita also has the capacity to produce small volumes of spodumene concentrate. The Cyprus Foote spodumene operation at Kings Mountain, NC, ceased production in 1992. It once produced about 2 kt/a (2200 stpy) of "high iron spodumene" for uses other than in the manufacture of lithium chemicals. The lithium products of the major producers are shown in Table 1. The current resources of 13 Mt (14.3 million st) of LCE in the western world will supply demand for more than 50 years.

Jan 1, 1993

By MANZOOR ALI BROHI, IZHAR MITHAL JISKANI, Atta Ur Rehman, SHUAI HAN, MUHAMMAD TARIQ, NIAZ MUHAMMAD SHAHANI

The analysis of mine safety indicators using a scientific method can improve mine safety and assist management in making informed decisions. This research establishes a mine safety evaluation index and proposes an integrative evaluation model based on the entropy weight and grey clustering methods. The index consists of 27 indicators classified into seven criteria: working environment (A), miners’ attributes (B), safety policies and education (E), prevention and control (F), and monitoring and supervision system (G). Using Pakistan’s mine safety situation as a case study, the proposed model categorized the indicators into five safety levels (very low, low, medium, high, very high) for the present situation and for their relevance in terms of future safety improvement. The results show all of the criteria falling into the very low level for the current mine safety situation. Three of the criteria — C, E and G — are identified as having very high levels of significance for future safety improvements.

By Yang Ge, Yuzhu Pan, Mansheng Chu, Jue Tang, Cong Feng, Lihua Gao, Zhenggen Liu

Increasing attention is being paid to laterite nickel ore as an alternative to nickel sulfide ore to act as a feedstock for nickel metal production. While laterite nickel ore accounts for a lion’s share of global nickel resources at approximately 72 percent, it accounts for only 42 percent of the world’s nickel production. In addition, the processing of nickel sulfide ore is confronted with enormous challenges due to deeper drilling requirements, higher production costs and depleting reserves. The nickel content in the nickel laterite ore associated with hydrated iron oxides and silicate minerals limits the application of physical beneficiation methods for the removal of iron. Thus, magnetic reduction roasting followed by magnetic separation has been regarded as one of the attractive routes to concentrate and separate the valuable metals from the impurities. 

By C. Zhou, B. Whisner, J. Carr

Proximity Detection Systems (PDSs) are used in the mining industry for protecting mine workers from striking, pinning, and crushing injuries when they work in close proximity to heavy machines such as continuous mining machines (CMMs). Currently all Mine Safety and Health Administration (MSHA) approved PDSs are magnetic field based systems which can be influenced by the presence of wire mesh that is commonly used for supporting roof and ribs in underground coal m ines. In this paper, researchers at the National Institute for Occupational Safety and Health (NIOSH) characterize the influence of the mesh on the performance of magnetic PDSs by measuring the magnetic field difference around a CMM caused by the presence of the mesh. The results show that the magnetic fields are generally enhanced by the mesh which causes the PDS detection zones to be increased correspondingly. It was discovered that the fields around the joints of two mesh sections have the greatest enhancement and thus deserve more attention. In addition, it is found that the presence of mesh can also cause a variation in the generator current. The influence of mesh is characterized by the change in the generator current with respect to the distance between the generator and the mesh. It was found that the generator current change caused by the mesh can be significant (on the order of ten) when the mesh is extremely close to the generator (e.g, less than 1 cm) and is negligible when mesh is relatively far (greater than 0.15 m). The findings in this paper can be used to develop guidelines and best practices to mitigate the influence of mesh on PDSs. INTRODUCTION The Mine Safety and Health Administration (MSHA) requires operators of underground coal mines to equip place-changing continuous mining machines (CMMs) with proximity detection systems (PDSs) to protect mine workers from striking, pinning and crushing injuries when they work around these heavy machines. Although a variety of technologies can be implemented for proximity detection, the magnetic-field-based PDS that was originally developed at the National Institute for Occupational Safety and Health (NIOSH) has shown great effectiveness in challenging mining environments and currently all MSHA-approved PDSs are magnetic-field-based systems. As shown in Figure 1, a magnetic PDS typically includes two major components----the magnetic field generator and the Miner Wearable Component (MWC). Magnetic fields are generated by injecting a high electric current into a ferrite-rod antenna sealed in the generator. The magnetic field strength detected by an MWC varies with the distance between the MWC and the generator. In a typical PDS, multiple generators are mounted on different locations of the machine. The relative location/zone of an MWC is determined based on the field strengths from different generators picked by the MWC. Ideally, for a PDS to work properly in the underground, the magnetic fields generated by the different generators should be stable and not vary with the environment, as the system would interpret any variation of the magnetic field as a result of the distance change between the machine and the miner wearing the MWC. In reality, however, this is not always the case since magnetic fields can be altered by a number of environmental factors such as the presence of steel wire mesh that has been widely used in underground coal mines for supporting roof and ribs In this paper, the influence of mesh on the PDS performance is investigated and the magnetic field change caused by the mesh is measured.

Jan 1, 2019