Search Documents

By Richard R. Klimpel

Part 2 of this article continues the discussion of a 10-year, multimillion dollar research and plant testing program on slurry rheology and grinding circuits. The first part of the article (ME, Dec. 1982) presented the basic concepts identified by the research and some laboratory test results. This section Illustrates typical Industrial scale test results and Identifies some industrial operating implications of controlling rheology by different methods. At least four controllable factors decide the rheological character of a slurry-slurry density or percent solids, particle size distribution, chemical environment, and slurry temperature. The second factor has two interrelated facets: the shape of the particle size distribution which controls packing behavior of the solids, and the fineness of the distribution. Finer particles increase interparticle forces and viscosity. As indicated in Part 1, during a given grinding test it is possible for all four factors to change. However, regardless of the particular settings of the four factors in a given test, if the resulting rheological character is either dilatant, pseudoplastic, or pseudoplastic with yield, the associated breakage rate is correlated with the current rheological character. It is obvious, for example, in batch grinding tests run at constant percent solids, that the second and third factors, where appropriate, are changing during grinding because size distributions are changing and the production of fresh surface area takes up unadsorbed chemical. Thus the corresponding rheological character change in batch tests with increasing grind time would be dilatant to pseudoplastic to pseudoplastic with yield. The degree to which this transformation occurs depends on the changing setting of the four factors over grinding time. In continuous grinding tests, one might logically expect that dramatic changes in any one of the four factors will be less likely to occur. It will be shown that continuous mill operations offer some unique opportunities to take advantage of possible rheological transformation by more direct operational control of the settings for the four factors. One extra observation noted in the rheological studies was the variability in the location and extent of region B (pseudoplastic behavior) for the various coals and ores tested. The location of region B was usually in the region of 45-55% solids by volume and was of the extent of 0-8%, or 2-11% with chemical addition. The corresponding increase in net production ranged from 0-10% in region B and 0-21% in region B&apos;. When region B is small or zero (no pseudoplastic character is exhibited) no increase in production will be observed and the use of chemicals is often marginal. There are several reasons for some materials exhibiting this quick transformation from dilatancy to high yield values often at surprisingly low percent solids by volume such as 30%. One condition identified was for materials containing high levels of viscosity-producing elements such as- carbonates or clays. A second condition documented was for materials that exhibited unusually fine primary fragment distributions (fine B1,; curves). This corresponds to materials having small y values of < 0.5. Such a slurry developed a yield value quickly during grinding because of the rapid buildup of fines. A related problem can be presented by materials exhibiting excessively coarse primary fragment distributions, y values > 0.9. Breakage of this type of material produces size distributions that give poor packing efficiencies even at long grind times, thus hindering the normal rheological transformation presented earlier. A final condition that can cause the occurrance of region B to be small or zero is when the media void volume filling of slurry is < 100%. Figures 5a and 5b use previously published data of this study to demonstrate the influence of solids loading and weight percent solids on the net production of taconite ore in a laboratory batch ball mill. In particular, Fig. 5a illustrates several trends not generally recognized until this study. They include these two: • Increased slurry density allows for increased solids loading before passing through the maximum in the net production curve where the fall-off is due to non first order breakage. • The use of rheology control chemicals such as GA-4272 allows this trend to be extended to higher slurry loadings with an increase in net production over any previous condition by keeping grinding first order. Figure 5b shows the same data as Fig. 5a plotted for constant weight loadings. These various figures of net production versus percent solids show the location and extent of the regions A, B, and C presented in Part 1 as a function of solids loading. It is obvious that the rheological transformation pattern described earlier does not hold true for slurry loadings corresponding to less than the void volume of the media, which is also a region of

Jan 1, 1983

By H. T. Mulryan

Talc is used as an essential ingredient in a wide variety of plastics applications ranging from polyester body patch compounds through polypropylene automotive, appliance, and household furniture components to high performance parts made from liquid crystal engineering resins. The paper focuses on polyolefin applications; the three tier market for talc in polypropylene; the effects of various talcs in typical compounds; and trends in each market segment. Emphasis is given to emerging markets, examples of which are polypropylene compounds which mimic higher cost resins, and polyethylene films, customer requirements for talcs for these purposes are discussed.

Jan 1, 1993

By ETHAN FUSTER, STEPHEN LEE, Richard Ray

By offering savings in space and capital cost compared to ducted axial and centrifugal fan systems, horizontally mounted jet fans are commonly used worldwide to ventilate vehicular tunnels. They discharge high-velocity jets to transfer momentum to the surrounding airstream to induce longitudinal flow in the same direction as the jet. Vertically mounted jet fans installed in exhaust shafts have been successfully used to ventilate a large passenger rail overbuild in New York City. A comparison of shaft dimensions, vertical placement of the jet fans and measured shaft airflows is presented to evaluate optimum jet fan configurations. Measured shaft airflows are compared to airflows predicted by computational fluid dynamics (CFD) simulations of a three-dimensional model of the overbuild.

Sep 1, 2022

By F. Ysla, M. Mendoza

This proposal, based on the CIEMAN Cajamarca - Hualgayoc initiative, focuses on “Transforming Abandoned Mine Lands’’ We aim to study and assess the feasibility of an innovative rehabilitation method. Contaminated soils will be moved from the upper to the lower site, encapsulated with geosynthetic barriers, and covered with topsoil. The decontaminated upper area will be used for planting trees and large-stemmed plants for hiking and tourism, while the lower encapsulated area will support livestock and short- stemmed crops. This study will evaluate the economic viability and multi-use potential of this technique, promoting sustainable land recovery in Cajamarca, Peru.

Feb 1, 2025

By Thomas Camus

"STATE OF THE ART The current situation of ground prediction in TBM is of great concern for tunnelling contractors, and the subject has been quite widely addressed over recent years, for instance by the French Eupalinos 2000 programme, which tested a variety of technological approaches. A number of interesting projects were executed, such as the SOUND and OnSITE projects, part of the German Geotechnologien programme: these projects are focused on seismics, while other techniques such as radar are not considered. Little information and even less industrial applications have been released apart from lab simulations and numerical modelling. A number of field tests in different configurations have been carried out for compression waves, but the results were often not reliable or convincing, and therefore little has been reported in open literature. The advances seem somewhat promising as far as hard rock tunnels are concerned, but ignore the problem raised by concrete lined tunnels such as those bored by a TBM in soft ground. In such tunnels, sending and receiving seismic waves reliably through the lining (and the grouting behind) is quite illusory. A careful analysis of the seismic prediction research results show that the main problem is the source which is poorly controlled and poorly coupled (for instance in concrete lined tunnels, or in approaches that use the TBM cutter head vibrations as a source). Generating waves perpendicular to the tunnel axis is also a problem: aligning with the tunnel axis makes more sense. Radar (Ground Penetrating Radar - GPR) has been used in geotechnical surveys for decades, and also for tunnel inspection. Attempts have been made at using it on a TBM (for example in Japan by Taisei) but mainly using off-the-shelf GPRs, which are not adapted to work in the specific environment of a TBM (because of its huge mass of metal, to start with). Very few results have been published, probably due to the somewhat disappointing performance of such implementations. At present, no TBM has a GPR incorporated in its cutter head that is able to predict ground characteristics while drilling. Another characteristic and drawback of most current methods is that they require dedicated periods of time during which other tunnel construction activities must be stopped. Due to the duration of such operations this leads to performing ground prediction on a weekly basis only, and therefore to a requirement for an investigation range of 100 metres approximately (in order to cover the TBM advance over the coming week). This is not achievable with boreholes made from the TBM, even less if a reasonable accuracy is required, as is usually the case."

Jan 1, 2016

By R. W. Henn

Introduction Shotcrete, by the American Concrete Institute definition, is mortar or concrete pneumatically projected at high velocity onto a surface. The term gunite is still common in literature. It is a trade name established by Cement Gun Co. of Allentown, PA, around 1911 for a dry mix of fine aggregate material, hydrated at the nozzle, and pneumatically projected at high velocity onto a surface. This article will discuss shotcrete applications, ingredients, mix proportioning, batching and mixing, admixtures, testing, and steel fiber vs. conventional shotcrete. Applications Shotcrete is used primarily by the mining and underground construction industries to temporarily stabilize an excavated rock surface until a permanent cover can be installed. It may also be used as the permanent covering material. Other uses include refractory material, architectural finishes, slope stability, wearing surfaces, repairing existing concrete structures, fireproofing, and corrosion protection of steel. Wet Versus Dry Process In the wet process, all ingredients, including water but not accelerator, are mixed the same way as normal concrete before its placement by pneumatic projection. The accelerator is added in a liquid state through the nozzle at the point of placement. In the dry process, all ingredients, including acceleration in dry form but not water, are mixed just before placement by pneumatic projection. Water is added through the nozzle at the point of placement. Liquid accelerator may be added at the nozzle in the dry process. Ingredients Shotcrete consists basically of the same ingredients as concrete with some limitations. Type I, II, and III cements are used. However, Type II seems to be used most in underground applications. This can be attributed to ground water at most sites having slight to moderate concentrations of sulfates. Air-entraining cement or air-entraining admixtures are generally not used in dry mix shotcrete. It is generally agreed that it is impossible to entrain air due to the absence of the usual concrete mixing action, and the high velocity of impingement of the material on the application surface. Air-entraining cement or air-entraining admixtures are used in wet mix shotcrete. Their use, however, is not widespread due to the placement method and the fact that high velocity air drives off most of the entrained air. Test results are not conclusive in showing any durability increase of shotcrete to freezing and thawing by using entrained air. In spite of current practice, the trend is toward additional research, with more agencies and owners requiring the use of entrained air. The philosophy behind this is that some entrained air is better than no entrained air to increase durability to freezing and thawing. The aggregates used in shotcrete are the same as those used in concrete. However, the largest coarse aggregate presently used is 19 mm (0.75 in.). A typical gradation requirement is shown in Table 1. The water quality requirement for shotcrete is the same as that for concrete. Accelerators are by far the most important admixture in shotcrete.

Jan 6, 1984

By Robert O. Vernon

The discussion of water and pit mining together is most appropriate. In fact, water can be considered a mineral and a well a narrow pit. Thus, of all the mineral resources mined, water is probably the cheapest, most valuable and least valued. The delivered price, including mining, transportation, storage and marketing rarely exceeds ten cents per ton, and our economy would cease without it. The time has come when the public must recognize that the extraction of a mineral resource from the land is a necessary and inevitable result of the industries? attempt to meet the demands of a growing economy. In so much of Florida, the lands mined can, with forethought and planning, be left as improved real estate, water conservation and management lands. On the other hand, the mining industries must face up to the need for the reclamation of land and compact with themselves, appropriate governmental agencies and with the mining states to restore mined lands to usefulness. Of limestone, sand, and clay 90 to 100 percent of the mined material is used, but with planning and specing, these pits, if they penetrate the water table, become valuable as real property. Phosphate, which returns about 70 percent of the mined materials to the pit, can reclaim the land for many purposes.

Jan 1, 1966

By V. O. Tenorio

The implementation of autonomous technologies for production in surface mines demands changes in the existing monitoring and control systems. The present study deals with the concepts involved in the development of a decision support system (DSS) for the supervision of a combined fleet of manned and unmanned equipment operating in a surface mine. The project was carried out as part of an autonomous mining program that lasted from early 2006 until the end of 2008. The objective of the DSS was to achieve short-term planning goals while maintaining safe working conditions. Supervisory tasks become more complex when several autonomous vehicles operate simultaneously alongside manned equipment. The operation center where the DSS was installed allowed autonomous vehicle operations to be controlled while tracking technology reliability experiments performed on control display interfaces and interaction provided design parameters for more complex supervisory systems for autonomous mines. Mining Engineering, 2011, vol. 63, no. 11, pp. 80-86. Official publication of the Society for mining, metallurgy and exploration, Inc.

Jan 1, 2011

By C. J. Gauvin

The Geological Department, headed by the Chief Geologist, is part of the General Engineering Division and is under the direct supervision of the Chief Engineer. The Geological Department is responsible for the technical direction of all work concerned with the finding and outlining of ore. It provides the mine operating staffs, with the necessary plans and sections to enable them to design pit and underground layouts and to, extract ores&apos; as required by outgoing cargoes. The department maintains grade and ore reserve statistics in conjunction with a mining recovery factor at year-end. These duties are performed through the co-operation of all departments participating in the overall operation. As a result, a steadily broadening use is being made of geology at Steep Rock.

Jan 1, 1960

By Alan R. Grant

Interpretation of presently available geological information indicates that most of the periods of significant metal deposition in the Washington Cascades Range are, at least in part, genetically related to late Cretaceous -Tertiary intrusive episodes. Chemically, the most favorable environment for base metal deposition is high in potassium. Characterizing the advanced stages of these chemical alteration conditions are the silicate mineral assemblages orthoclase and/or secondary biotite. Wall rock alteration includes both deuteric and hydrothermal processes, the intensity of which primarily depends upon the degree of fracturing in the country rock prior to the introduction of secondary material. Broadly speaking, the primary physical controls for the distribution and concentration of sulfides appear to be a series of structural couples involving both northwest (paralleling regional trends) and northeast--striking systems. Meaningful base metal exploration in the Washington Cascades demands a basic understanding of the various geologic factors related to the distribution of the sulfide deposits. Any geologist contemplating Cascade work should be well grounded in the fundamental concepts of petrology and structure.as these constitute two of his most beneficial aids. The acquisition of the detailed data necessary for this understanding may seem a bit academic, yet it has been demonstrated in numerous instances that a fair economic appraisal of a particular property or mining district depends primarily upon the ability of the geologist to recognize the subtle environmental differences which could lead to the discovery of a major ore deposit.

Jan 1, 1971

By Jake Beale, Joe Wickline, M. Van Dyke, Ted M. Klemetti

A longwall coal mine in southwestern Virginia mining the Pocahontas #3 Coal Seam experienced a history of mining-related seismic events. The events were never large enough to cause concern until three major events occurred recording 3.4, 4.3, and 3.4 ML in 2005, 2006, and 2007 respectively. Two of the seismic events generated an air blast which damaged stoppings which fueled a mine fire in 2005 and 2007. The mine responded to the events by narrowing the longwall widths, changing ventilation controls, installing a 7-sensor seismic system around the active panel, and creating a mining hazard map to avoid similar geology in the future. All of the actions taken have prevented seismic activity from impacting mining operations, but it did not prevent other large seismic events from occurring (Van Dyke et al., 2018). In 2016, another large seismic event, measured at 3.7 ML, occurred in the gob that was reported by the local media and recorded by the United States Geological Survey (USGS). While the event did not directly impact mining operations, mine management wanted to know where and under what conditions could large seismic events occur in the future. The National Institute for Occupational Safety and Health (NIOSH) became involved to help understand what conditions precipitated these events so that future mine design could more accurately assess seismic hazards and reduce the risk to mine worker safety. Researchers at NIOSH and mine management created a seismic forecasting map that combined three factors: (1) overburden thickness, (2) sandstone thickness, and (3) the expected caving height of the gob. The criteria were developed based on the geologic data the mine collected from core drilling, e-log analysis, and fiberscope observations. The forecast map was able to provide an accuracy of 72%–85% of events 1.5 ML or greater and 100% accuracy of events that were 3.0 ML or greater based on historical data. The seismic forecasting map was applied to the entire future mining area to show areas where seismic potential could be the greatest based on current mine design planning, ultimately improving the ability of the mine operator to assess the seismic hazards surrounding active and future mining areas (Van Dyke et al. 2018). Following this research, the seismic forecasting map was implemented into the mine’s hazard recognition program and is continuously updated and evaluated prior to mining each longwall panel. This paper will cover in more detail how the seismic and lithologic data was processed and how the mine implemented a new seismic mitigation program based on the forecasting results.

Apr 26, 2022

By E. h. Erwin Gaertner

Before dealing with the technical equipment of this paper a short survey of the Rhenish Brown Coal Area is given in order to illustrate the special geologic and environmental conditions in this region, which led to the development of the mining technics, used today.

Jan 1, 1975

By Monica Campos, Jose Mujica, Maria Campos

The extraction and processing of metals and other minerals have played an important role in economic, political, and social development worldwide, from the early stages of prehistory to the present day (Gosner, 2020). In other words, mining has been a fundamental part of human civilization, providing the raw materials necessary for technological, infrastructure, and industrial advances. As society progresses, the importance of mining continues to grow, supporting the development of everything from the smallest electronic devices to the tallest skyscrapers (The Importance Of Mining In Modern Society, 2024). The mining industry is closely linked to a country’s economy and activities related to natural resources. The economy of a nation is connected to its extractive industries (Moreira & McMahon, 2014), which have seen dramatic growth in recent years (Pietrobelli et al., 2018). In a context of increasing demand for natural resources, driven by the development of emerging technologies, the expansion of infrastructure, and the foundation of engineering achievements for the coming decades (Importance Of Mining - Minerals Education Coalition, 2024), mining should focus efforts on global development, requiring a comprehensive approach to sustainability that addresses the planet’s needs and protects the well-being, primarily, of the communities and environments where mining operations take place (Figari, 2024). In these areas, diversity and inclusion should be promoted, thus fostering equitable and sustainable development. Speaking of sustainable development, diversity, and inclusion brings us to an interesting topic: the Sustainable Development Goals (SDGs), also known as the Global Goals, which could serve as a key framework for fostering a strong social management culture in mining. The SDGs were adopted by the United Nations in 2015 as a universal call to end poverty, protect the planet, and ensure that all people enjoy peace and prosperity by 2030 (Sustainable Development Goals, n.d.). Companies have compelling reasons to align their actions with the SDGs, as their long-term success depends on healthy communities. This is a major challenge and requires collaborative efforts (Singh & Rahman, 2021). As Fraser (2021) mentions, achieving more sustainable outcomes may involve mining companies and communities working together collaboratively. This research proposes an innovative approach: Inclusive Mining for Sustainable Development, which aims not only to maximize economic profitability but also to promote social and environmental well-being by integrating the United Nations’ Sustainable Development Goals (SDGs), primarily focused on diversity and inclusion. This can be achieved through the implementation of a key value-added initiative for mining companies: the Creation and operation of a corporate volunteering program aimed at developing and executing inclusive practices to promote gender equality, the inclusion of local communities and indigenous peoples, and accessibility for people with disabilities. This proposal will educate employees and stakeholders about sustainability and promote concrete actions through corporate volunteering to strengthen the mining company’s commitment to community development, improve social relations, and advance toward achieving the United Nations’ Sustainable Development Goals, establishing the company as a global change agent.

Feb 1, 2025

By Michelle Pienaar, Musa S. D. Manzi, Thabang Kgarume, Glen T. Nwaila, Raymond J. Durrheim, Abrie Oberholster, Hennie Grobler

The South African Mining, Extraction, Research, Development and Innovation (SAMERDI) strategy was launched in 2019 with the goal of modernizing the mining industry. It comprises three major research initiatives: improvement in the efficiency of extraction and health and safety in current mining operations, development of fully mechanized systems to mine narrow tabular ore bodies in hard rock, and development of extraction systems to break rock without using explosives. The crosscutting Advanced Orebody Knowledge (AOK) program seeks to develop and implement drilling and geophysical technologies that can characterize the rock mass ahead of mining and identify potentially hazardous geological features. This knowledge will be integrated with information derived from seismic monitoring. Mining methods, layouts and rock support systems will be adjusted accordingly to mitigate the risk of rockbursts. Boreholes are routinely drilled ahead of mine workings using diamond-impregnated bits. The drill core is logged to identify lithology and geological structures (especially dykes and faults that may be seismogenic), sample the ore body for grade control, and detect areas that may contain water and/or flammable gas. Methods and technology to improve the efficiency of drilling and maximize the information obtained from the drilling process, borehole core, and the borehole itself are being investigated. A range of geophysical technologies are being developed to map the rock mass from the skin of the excavation to a distance of several tens of meters. Light Detection and Ranging (LiDAR) is used to map the geometry of the excavation, including prominent joint, vein and fracture sets and the presence and performance of rock support elements and systems. Ground Penetrating Radar (GPR) is used to penetrate deeper into the rock mass and image joints, fractures bedding planes that influence the stability of the hanging and side walls. Image processing techniques known as ‘seismic attributes’ are being applied to the radargrams to improve interpretation. Electrical Resistivity Tomography (ERT) and various active and passive seismic techniques (e.g. Tunnel Seismic Profiling (TSP), ambient noise tomography) achieve even greater penetration into the rock mass. Finally, machine learning is used to improve the processing and interpretation of seismic and radar data.

Apr 26, 2022

By John E. Miller

Unit Rig & Equipment Co., manufacturer of Lectra Haul Trucks, is continually studying methods of reducing the operating costs of large haulage trucks. Reduction of haulage system operating costs is an important goal that equipment operators and equipment manufacturers constantly try to improve on. One of the most variable and important factors affecting operating costs is actual truck operating practices. An examination was centered on methods to optimize truck utilizaion. It was found that a very effective method of accomplishing this goal would be an Automatic Truck Control (ATC) system to automatically control a fleet of haulage trucks in a predetermined pattern. Economic studies were conducted which showed a very favorable reduction in mine operating costs by use of an ATC system. In 1970, Unit Rig & Equipment Company, in conjunction with SAAB-SCANIA began preliminary development of adapting for truck use a proven automated control system previously used for train systems, small trucks, and military target vehicles.

Jan 1, 1979

By J. R. Hurley

The continuous flow, horizontal drum blender has dynamic properties which may be described by the same type of equations which often arise in electrical filter analysis. Furthermore, the equations may be readily solved by the same techniques used in electrical control analysis. For this reason the blender model developed is termed an "Electric Analog", although strictly speaking it is a mathematical model. Presentation of the dynamic performance of the blender as an electrical (or mathematical) model is desirable for several reasons. The model can be of assistance in correlating performance data with equipment design parameters. The model &apos;can be used with other process equipment models for simulation of an entire plant operation or in stability studies. In addition, the model may be useful in providing insight into the actual blending mechanism, or it may suggest a similar method of analysis for other closely allied equipment.

Jan 1, 1967

Blast vibrations induce sounds within neighboring residences. A house wide vibration and sound monitoring system was installed in a West Virginia home which was subjected to blasts at varied distances and direction. Eighty-nine blast events were monitored and analyzed for this case study. Fifteen channels of data were collected including three triaxial geophones, one airblast microphone, one uniaxial geophone mounted to the wall of the house (response channel), and four microphones that recorded CD quality sound waves inside the house. Each of these channels was recorded on the same time reference and scale allowing for direct comparison of the waveforms. The response channel signal was easily separated into ground vibration induced and airblast induced movement due to the differences in their times of arrival. This response channel was then compared to the sounds recorded inside the home to determine which component of blast vibration induced the maximum sound response inside the home. Blasts at distances less than 762 meters (2,500 feet) had maximum sound responses from both ground vibration and airblast. While for blasts beyond 762 meters (2,500 feet), the maximum sound response inside the home was caused by ground vibration without exception. When airblast was identified as the dominant sound generator in the house, the peak amplitude of the sound was directly related to the amplitude of airblast. When ground vibration was identified as the dominant sound generator in the house, the peak amplitude of sound was not related to the amplitude of ground vibration. In these cases, sound amplitude was driven by the conditions present in the house such as loose items, doors, and windows creating sudden peaks from falling or slamming. In the same respect, sound amplitudes varied depending on where the sound was recorded. Different rooms generated very different sounds based on the contents of the room. Findings from frequency analysis showed that the frequency content of sounds inside the house were not related to frequency content of airblast or ground vibration regardless of source suggesting that residents would have difficulty determining the source of blast induced noise in their homes.

Jan 1, 2010

By B. Ollila, L. Brown

As mining fronts converge in sill pillar extraction, the mine seismic hazard can be significantly altered and large seismic events have been known to occur. This study used common seismological tools to analyze the extraction of highly stressed sills from two deep Canadian mines with the objective of characterizing the rock mass failure process and relation to large seismic events. The approach treated a sill pillar as a mine-scale failure process, meaning the temporal and spatial analysis scales needed to exist on a similar scale to a significant part of the mine. The temporal analysis scale overlapped with the entire mining sequence, included several years of data to establish long term change in the characteristics of rock mass failure. The spatial analysis scale included the rock mass surrounding a large part of the convergent mining sequence. To accommodate the large spatial and temporal scales, the highest magnitude 2% of events in the dataset were analyzed. Similar results were shown for sill pillars in both mines. Changes in event location, time, magnitude, energy index and apparent volume were similar to expected behavior of rock failure. Indications of strain hardening and strain softening were observed in the sills. The hardening period was characterized by a high rate of small events, high energy index and low apparent volume, giving an indication of high stress and low rock yield. The softening phase was characterized by a decrease in the rate of small events concurrent with an increase in the rate of large events, low energy index and high apparent volume, indicative of release of stress and increase in deformation. Large magnitude seismicity was strongly related to the softening phase, with several Nuttli magnitude 3.0+ events occurring shortly after the transition from hardening to softening failure regimes. Sill failure was indicated by consistently low EI and low levels of seismicity and seismic hazard in the sill pillar.

Apr 26, 2022

By Paul K. Sims

The Central City district is one of several adjacent mining areas in the Front Range, Colorado, that contain precious metal-bearing sulfide veins of Laramide (Late Cretaceous and early Tertiary) age. The districts are in the Front Range segment of the Colorado mineral belt, and are characterized by porphyritic igneous rocks of intermediate composition that have intruded Precambrian crystalline rocks in the core of the Front Range. The veins and minor stockworks that constitute the ore deposits in the district were formed largely as fracture fillings. The veins range from simple fissures to complex, branching lodes, and commonly range from less than 0.5 to about 1 m in width. The principal values are in gold and silver. The common metallic minerals are pyrite, sphalerite, chalcopyrite, tennantite, and galena; minor minerals are enargite, pitchblende, and gold tellurides. Quartz, cryptocrystalline silica, carbonates, fluorite, and barite compose the gangue. The ore deposits have a well-defined concentric zonal arrangement. A core of pyrite veins (central zone) is surrounded by a peripheral zone of galena-sphalerite vein with gold and silver. An intermediate zone contains transitional veins that have minerals characteristic of both the central and peripheral zones. The minerals were deposited in three stages during a single period of mineralization: uranium; pyrite; base metals, gold and silver. The wall rocks were altered primarily during pyrite-stage mineralization. Sericite envelopes developed adjacent to fractures, and were succeeded outward by zones of argillized rock. The valuable ore minerals were deposited in ore shoots localized by several types of structural controls, principally vein intersections, the physical nature and structure of the wall rocks, and irregularities along the fractures themselves. During supergene alteration, gold was concentrated in the upper, oxidized parts of the veins, commonly to depths of 50 m. The precious metal-bearing sulfide ore deposits are closely associated in space and time with the Laramide porphyritic igneous rocks and are believed to have been derived from hydrothermal fluids related to the magmatic activity. The ore deposits have mesothermal aspects and apparently formed in the temperature range 200°-320°C.

Jan 1, 2013

By CLAIRE STREBINGER, ADITYA JUGANDA, JURGEN F. BRUNE, GREGORY E. BOGIN JR.

Methane gas explosions are a major risk in underground coal mining operations. The severity of such explosions can range from local area damage to massive loss of miners’ lives along with significant damage to mine infrastructure and ventilation controls that may lead to mine closure and loss of the entire operation. This study demonstrates the viability of integrating a computational fluid dynamics (CFD) combustion model into a longwall mine ventilation model to simulate methane gas explosions in the longwall face area. The resulting 3D methane gas explosion simulation can provide better understanding of the fundamental physics and the potential impact of an explosion in an underground longwall coal mine.

Aug 1, 2022