Search Documents

By C. M. Chang, H Gu, J. A. Barrera-Godínez, T. J. O’Keefe

The inability to economically separate Fe3+(aq) from a variety of liquid effluents is a major Concern for the primary metals industry. A unique solvent extraction process, galvanic stripping, has been developed to address this problem. The galvanic stripping of iron from D2EHPA using only a 5~10 g/L H2SO4 solution is achieved after Fe3+ is directly reduced to Fee, in the organic phase using zinc metal additions. To date, the primary focus of the laboratory research has been on optimizing the parameters that control iron removal. The results from these studies have now been, used to make a preliminary design for a continuous flow process that is envisioned for zinc industrial applications. Specific quantitative data are shown for the use of a Zn-Ph cellos° in the iron-reams al process. Some introductory results on electrochemical potential measurements and impurity distribution with solution cycling are also giiven.

Jan 1, 2000

By Ross W. Smith, Salim Akhtar

Flotation of oxide minerals, particularly silicates, with cationic collectors differs substantially from classic flotation of sulfide minerals using sulfhydryl collectors. In the case of cationic flotation of these minerals, in general: 1. There is a greater importance of electrostatic interaction between mineral and collector. 2. Longer-chained collectors are required; as a rule at least 10 carbons must be present in the hydrocarbon chain. 3. Moderate concentration of collector is required. 4. Attachment between collector and mineral appears to be less strong even though the system may exhibit a large contact angle. 5. Required conditioning time before flotation is usually relatively short. 6. There is sensitivity to slimes. 7. The collectors usually possess frothing power. 8. Selectivity of cationic collectors for specific minerals is usually poor. Almost any of the oxide and silicate minerals may be floated using cationic collectors. However, specific response to these collect- ors varies with mineral type. The following classes and minerals are

Jan 1, 1976

By P. D. Rao, D. E. Walsh

A pilot-scale study was performed to evaluate the potential for gravity concentration of gold from -13 mm (-1/2 in.) crushed ore from Ester Dome, AK. 9.04 t (9.94 st) of crushed ore were sampled and processed through a Pan-American jig-Wilfley table pilot plant. Plant products were sampled for assay and material balance calculations. Gold recovery through one stage of jigging and two stages of tabling was 17.4% at a concentration ratio of 615:1. Concentrate grade was 766.3 g/t (22.4 oz/st). The feed grade to the plant was calculated at 1.71 g/t (0.05 oz/st). Jig tailings, primary table tailings and secondary table tailings grades were 1.44 g/t (0.042 oz/st), 1.30 g/t (0.038 oz/st), and 5.47 g/t (0.16 oz/st, respectively. Significant coarse, free-milling gold values were shown to remain in the, jig tailings. Concentrate mineralogy is discussed.

Jan 1, 1992

As mentioned in chapter 8, one of the objectives of the budget is to provide a mechanism for ongoing measurement and control of the production operation. The budget shows expected performance. Actual results are compared to this benchmark to evaluate past performance and to direct future activities. The variances between budgeted and actual results identify specific activities that did not perform as expected (whether negatively or positively). Managers who use variance analysis are essentially applying a management- by-exception philosophy. Individual organizations will determine variances that reflect their own processes and managerial interests, but these variances all follow the approach outlined here. Firms will also vary in the extent to which variances are reported. Some firms use a few variance measures for the overall production organization whereas others calculate variances for individual departments or even individual work areas. As mentioned in chapter 5, it is important to distinguish between controllable and noncontrollable costs when using budgets for control and evaluation.

Jan 1, 1999

By M. Leroux, S. R. Rao, J. Kim, V. Gervais, J. A. Finch, G. Labonté, N. Macminn, M. Ounpuu

Collectorless flotation of sulphide minerals from Lyon Lake ore (Mattabi Mines Ltd.) has been studied both in the laboratory and plant. Among the four major minerals chalcopyrite showed the greatest response to collectorless flotation, followed by galena. Flotation of sphalerite and pyrite was minimal. Collectorless flotation was influenced by pulp potential and pH. Experiments using different gas compositions showed collectorless flotation was promoted when the pulp potentials were greater than about 0 mV (SCE). The study of the effect of depressants showed that SO2 at pH < 8.0 depresses both galena and chalcopyrite but at pH 9.5 flotation of chalcopyrite recovers. Use of NaCN preferentially depressed chalcopyrite compared to galena. Preliminary results from plant tests at Mattabi Mines Ltd. confirm that collectorless flotation occurs and that it is preferential for chalcopyrite and to a lesser extent galena. Practical implications of collectorless flotation in plant practice are discussed. A critical factor will be silver recovery.

Jan 1, 1989

By William Petruk

Volcanogenic base metal ores contain about 0.5 to 7 g/T Au, commonly as an intermetallic compound with Ag and/or Hg, and to a small extent • "invisible gold" in pyrite and arsenopyrite. The Au-bearing phase (electrum, Au-Ag-Hg alloy, etc.) generally occurs as fracture fillings in pyrite, arsenopyrite and chalcopyrite, and rarely • minute inclusions in pyrite and arsenopyrite. The Au-bearing phase in fractures generally occurs • small grains, and is frequently associated with galena, tetrahedrite and other late minerals. The gold is readily liberated from fractures and recovered by flotation in Ca concentrates. Copper concentrates usually recover around 60% of the gold when the ore grade is around 3 g/t. Higher recoveries are obtained for higher ore grades, and lower recoveries for lower grade ores. Lead and zinc circuits act as scavengers for gold, and recover all the exposed gold attached to small particles. Only unliberated gold, "invisible gold" and very minute gold grains attached to large particles are lost to tailings.

Jan 1, 1990

By J. A. Finch, J. Yiantatos, A. R. Laplante

This paper re-examines the mixing conditions in the collection zone of flotation columns. These have in the past been characterized with a single uniaxial dispersion coefficient, E. The relationship between E and column diameter, Dc, is examined based on residence time distributions (RTDs) in columns of Dc ranging from 5.lcm to 184cm. Results agree with published correlations in chemical engineering, i.e. E a Dc &apos;" , Data explain why pilot columns display significant upgrading between the feed level and the interface, whereas plant columns do not. It also suggests that, for plant columns, the full collection zone (up to the interface) can be considered when calculating the residence time. A mathematical model considering two regions of different mixing was compared to the single E model. Both models adequately fitted measured age distributions inside the column and overall RTDs. Measured and simulated mixing characteristics are compared to those of flotation banks, using a tanks-in-series approach; banks of comparable mixing to columns are identified.

Jan 1, 1988

By J. A. Dlas Lima

Alunorte is a metallurgical-grade alumina refinery located in northern Brazil. This plant which was designed to produce 1.1 million mtpy of calcined alumina, started operation in July 1995. A process information system was installed before refinery start-up. It has been a main factor in process improvements, which resulted in an increase in production from 1.1 to 1.5 million mtpy. This system has been particularly useful for analyzing data and allowing retrieval of data by process engineers. This paper describes how a quality monitoring system to evaluate all aspects and stages of production, as well as alumina silo level and blending percentage, was developed. This system was designed to give support to ISO 9002 certification, which happened in December 1998. The quality monitoring system was developed using Microsoft Excel 7.0 and makes extensive use of VBA macro. The primary users of the system are shift foremen, managers and engineers, who use it to track the process and avoid variations in alumina quality.

Jan 1, 2000

By W. K. Collins, C. L. Dahlin, D. C. Dahlin, W. K. O’Connor, G. E. Rush

Direct mineral carbonation was investigated as a process to convert gaseous CO2, into a geologically stable final form. The process utilizes a slurry of water, with bicarbonate and salt additions, mixed with a mineral reactant, such as olivine (Mg2SiO4) or serpentine [Mg3Si2O5(OH)4]. Carbon dioxide is dissolved into this slurry, resulting in dissolution of the mineral and precipitation of magnesium carbonate (MgCO3). Optimum results were achieved using heat-pretreated serpentine feed material and a high partial pressure of CO2 (Pc02). Specific conditions include 155°C, PC02 = 185 atm and 15% solids. Under these conditions, a 78% conversion of the silicate to the carbonate was achieved in 30 minutes. Process mineralogy was utilized to investigate the appropriate feed characteristics, identify the process products and interpret the mineral dissolution and carbonate precipitation reaction paths. Key words: Mineral carbonation, Carbon dioxide sequestration, Carbonates

Jan 1, 2003

By R. A. Jankowski

The US Bureau of Mines (USBM) conducted a series of laboratory tests to investigate the effectiveness of using a flooded-bed scrubber with exhaust ventilation in deep-cut faces. An experimental test program to determine the impact on respirable dust levels resulting from changes in face airflow, curtain-setback distance, operator positioning and operating parameters of the external spray system on the miner was completed. Gravimetric sampling was conducted in the immediate return and at three sampling locations on the off-curtain side of the entry. Statistically significant differences in dust levels, on the order of 0.5 to 1.2 mg/m3, were observed between specific sampling locations and changes in several test parameters. Dust sampling results indicated that a flooded-bed scrubber and exhaust ventilation can be a viable dust-control system for extracting deep cuts up to 12.2 m (40 ft) in length. The impact on methane was not evaluated.

Jan 1, 1998

By Gary A. Almeraris, Thomas F. Peyton

This paper chronicles the mining of a main interceptor sewer through a residential neighborhood for the MWRA&apos;s Boston Harbor clean-up. The Wellesley Extension Sewer Tunnel consisted of 490 m (1600 ft) of rock tunnel, 107 m (35V ft) of mixed face and 336 m (1100 ft) of softground. The tunnel was located 4.6 m (15 ft) below water table and passed directly beneath six buildings with as little as 7 m (23 ft) of cover. In addition, the tunnel ran parallel to and within 4.6 m (15 ft) of an existing sewer tunnel with flows up to 187,5 million liters (50 million gal.) per day. The rock encountered by the tunnel was comprised of gramodiorite, amphibilite and diabase. The soils which passed through the tunnel face consisted of tills, sands and non-cohesive plastic silts. The techniques developed and the equipment utilized to successfully mine this complicated ground are described.

Jan 1, 1991

By C. H. Rawlins

Deep bed media filtration is used as a tertiary treatment step (after hydrocyclones and flotation cells) to remove fine oil droplets and solids from oilfield water before reinjection disposal or to remove particulate material from surface waters used for waterflood injection. Oil and solids injection requirements are typically <5 ppm concentration at <2 micron diameter. The preferred media for produced water filtration is walnut or pecan shell, however the use of this media has evolved by trial & error and the fundamental mechanisms that occur during separation and media cleaning have not been investigated. A project was initiated to fill in this knowledge gap by analyzing the physical, mechanical, chemical, and hydrodynamic properties of six types of granular filtration media (12/20 mesh size): garnet, silica, anthracite, pecan shell, English walnut shell, and black walnut shell. Comparison of bed packing, oil wetting, attrition resistance, particle strength, and fluidization has led to an understanding of the preferred filtration media for separation of fine oil droplets and solids.

Jan 1, 2010

By Brian W. Hester

All gold occurrences in Tanzania are of Precambrian age and in geological settings similar to gold deposits in other parts the world. The three main areas of interest are perhaps the least prospected of areas of gold mineralization in Precambrian rocks in non- aligned, or market economy nations. Historic production exceeds 77.660 kg (2.5 million oz). Current results by small scale workers go unreported, but have been estimated to be as high as 11.000 kg (350.000 oz) annually. Gold occurs in both lower and upper Precambrian rocks. In the older. gold is associated with greenstones and iron formations typical of many cratonic areas of Precambrian age. The Tanzanian Craton lies in the north west quarter of the country where it is flanked on both east and west sides by mobile belts involving upper Precambrian rocks of high metamorphic grade. Gold occurs in fractures in the western belt within two distinct areas.

Jan 1, 1989

By M. Balakrishnan, K. A. Natarajan, J. M. Modak, J. S. Gururaj Naik

The ability of various fungal species isolated from gold mines to uptake gold and base metals such as zinc, copper, iron and lead from gold-process cyanide effluents was investigated. Under identical treatment conditions, different strains showed wide variations in their ability to take up gold and other base metals. Aspergillus terreus exhibited as high as a 60% gold uptake. Almost complete removal of zinc was possible with various fungi and with the yeast Saccharomyces cerevisiae. Studies at various metal concentrations showed a higher gold uptake from dilute solutions, and studies with Aspergillus niger showed that gold uptake by living cells increased gradually as the contact time increased. Metal uptake capacities between living and nonliving cells were also compared. A waste biomass (ABM- I), obtained from a fermentation industry, wasalso identified as having a high gold uptake capacity. At 5% (W/v) solids, ABM-I could efficiently remove up to 83% of the gold contained in an effluent solution within 24 hrs.

Jan 1, 1995

By Tim O’Neil

Many mining companies try to fight their way up from small operator and exploration company to major producer. Not many companies make it. Cambior Inc., formed in 1986, is one company well on its way to making it as a major operating company. In 1993, Cambior surpassed 15.5 t (500,000 oz) of gold production and began operations at its world class Omai gold mine in Guyana. At the same time, the company has embarked on a program of geographic and minerals diversification. Cambior, a Canadian company, now has interests in eight mines, three development projects and more than 100 exploration properties in North and South America. The company’s goal is to derive 70% of its income from gold and 30% from base metals and other minerals. Cambior’s moderate diversification into base metals gives protection against negative gold price fluctuations. It also balances the typically short term gold mines and the longer term base metal mines.

Jan 1, 1994

By Edward L. Mooney

In the, West, walking draglines often offer the least cost method of uncovering coal for surface mines. However, with each of these machines costing millions of dollars, a good deal of analysis can be justified by the potenial savings or, conversely, costs associated with the choice of a machine. This has resulted in the recent development of a number of computerized models for dragline selection and pit design. One of the earliest reported models for this purpose was developed by Dunlap and Jacobs (1). Later, Rumfeldt described the computer approach to sizing stripping draglines given the required production rate and mine site parameters (2). This basic approach is probably still the most widely used with models for more complicated mining methods reported by Stefanko, Tomica, Finch, as well as others (3,4,5). furthermore, detailed simulation models useful in this regard have been developed by McDonnell Douglas and Fluor, Utah (6,7)

Jan 1, 1982

Information Technology has addressed those problems unique to senior management in the mineral industry. In general, these problems are those concerned with decision-making. Peter Drucker in his discussion of making effective decisions identifies five phases: (1) define the problem, (2) analyze the problem, (3) develop alternate solutions, (4) decide the best solution, and (5) convert the decision into effective action. The scope of the chapter by Guernsey addresses the first three phases which provide input to the decision-maker. The decisions to be made relate, in most instances, to the economics related to a mineral property or process. Computer models have been designed to generate these economic and financial evaluations. No one model is appropriate to the solution of all management&apos;s problems. In this chapter several applications are identified and summarized; a model for the economic evaluation of a mineral property is described in greater detail. The implementation of such models is dependent on the unique needs of management.

Jan 1, 1979

By D. Altizer, E. Thompson, K. F. Unrug

Because of frequent sudden changes in the geologic composition of strata, the extrapolation of rock properties obtained from core samples to the surrounding areas can cause problems. To address this issue, a method of rapid strength testing in situ using a borehole penetrometer is being developed. This method, as opposed to conventional laboratory testing, does not require rock samples to be retrieved and handled/machined before testing. Rock strengths are determined di¬rectly on the drill-hole wall. The latest development is a borehole penetrometer that requires only a 38.1-mm- (1.5-in.-) diam hole. The small diameter of the penetrometer body allows for the drilling of test holes with production mine equipment such as a roof bolter. The new penetrometer allows for the possibility of a broad application in coal mines, as well as in hard rock mines and tunneling. The principles of the apparatus are described and are illustrated with examples of its applications.

Jan 1, 2002

By D. E. Walsh, J. T. Hollow, H. K. Lin, J. L. Oleson

At the Fort Knox Mine, Fairbanks, Alaska, carbon fines are generated during stripping, acid washing and kiln regeneration operations. Because of their gold value, carbon fines are collected by a filter press. Samples of the carbon fines show that they consist of 20% to 30% carbon, 70% to 80% grit and 0.17 to 0.68 g/kg (5.0-19.9 oz/st) gold. About 80% of the gold values in the carbon fines used in this study are in the form of recrystallized free gold grains, with the balance being the adsorbed gold on the carbon. High recoveries of gold and carbon were obtained from the fines in laboratory tests using froth flotation, with a high rejection of the grit. More than 95% of gold and 90% of carbon can be recovered by three stages of gold flotation followed by two stages of carbon flotation. Key words: Gold recovery, Activated carbon, Flotation

Jan 1, 2003

By N. S. Dalal, Xianglin Shi

Metal ions, such as chromium (Cr) and vanadium (V) are found as trace impurities in mineral dust. Since metal ion mediated free radical generation has been implicated in many disease processes, we carried out a detailed investigation of the metabolism of these metal ions by biological redox systems and the possible oxygenated radical generation therefrom. We found that highly reactive Cr(5+) species are generated in the reduction of Cr(6+) by NADPH-dependent glutathione reductase, lipoyl dehydrogenase, and ferredoxin-NADP+ oxidoreductase. The reduced metal ion species react with hydrogen peroxide, to generate hydroxyl (•OH) radicals in a continuous cycle. The enzymatic catalysis processes also involves the reduction of molecular oxygen to the superoxide [(0-1 2)] radical. Thus only a trace amount of metal ions chemisorbed on mineral dusts, such as quartz, can catalyze the generation of the highly toxic oxygenated radical species from cellular hydrogen peroxide, suggesting a new biochemical mechanism for mineral dust induced chronic lung injury.

Jan 1, 1991