Search Documents

By S. S. Cook, S. E. Paulson

The US Bureau of Mines is conducting core leaching experiments with sulfuric acid on oxide copper ores from the Cyprus Casa Grande and Asarco/Freeport Santa Cruz deposit in Arizona to further the understanding of the leaching process in supergene copper ores as it relates to in situ mining. Leach solutions from atacamite mineralization contained 5 to 30 g/L (0.05 to 0.28 oz/gal) copper and few extraneous ions. Leachant from chrysocolla ores, with grades similar to the atacamite, contained 2 to 9 g/L (0.02 to 0.08 oz/ gal) copper and abundant extraneous ions. Quartz and K-feldspar had no impact on leach solution composition at any acid concentration up to 40 g/L - (0.39 oz/gal) while illite and sericite had minimal impact. Biotite, calcium-rich clay, and limonite have a significant impact on solution chemistry when there is abundant free acid in solution. High acid concentra¬tions increase acid consumption in ores with abundant biotite and limonite gangue. High acid concentrations can be used in ores with quartz, K feldspar, and sericite gangues without increasing acid consumption per unit of copper removed.

Jan 1, 1990

By H. Wesley Peirce

Although not generally recognized, Arizona has rock salt deposits unique in the United States. This uniqueness stems from a combination of two factors: (1) relatively youthful geologic age and (2) nonmarine origin. Although Arizona shares one deposit with Nevada (Figure 1, No. I) there are three others within the State (Nos. 2, 4, 5) that are believed to be both late Cenozoic in age (less than 15 million years) and nonmarine in origin. The only other recognized nonmarine salt deposits in the U.S. are much older, being in the early Cenozoic (Eocene) Green River Formation of Colorado and Wyoming. According to Johnson and Gonzales (1), the remaining rock salt deposits in the United States are marine and either Paleozoic or Mesozoic in age. Of the seven localities shown in Figure 1, six in the Basin and Range geologic province are believed to represent nomarine late Cenozoic phenomena and one (No. 7) in the Colorado Plateau geologic province is Paleozoic (Permian) in age and marine in origin. The following comments are intended to update the general geologic highlights of these deposits and to summarize the nature of their present utilization.

Jan 1, 1979

By J. D. Goodrich

Success of The Carter Mining Company's safety program can be primarily attributed to "total immersion" of all operating and staff personnel in program design and implementation. Currently, the Company operates two surface coal mines in Campbell County, Wyoming. Total employment is about 440 and current annual production is about 15 million tons. The safety program has evolved from one which was administered primarily by staff personnel (the Safety Department) to one which requires active participation by line management and operating personnel. Lost time accident frequencies have declined from a high of 1.86 per 200K hours worked in 1978 to zero in 1982. Reportable accident frequencies have declined from slightly over 5 to slightly over 2 during the same period. Analysis of program results indicates that the most important achievement by the company has been to gain strong commitment to safe operation by all employees. It is important that program format and content be frequently changed and modified so that: 1) The requirement for safe job performance is communicated well and often, 2) The safe job performance message is trans- mitted in new and interesting ways, and 3) Operating personnel participate in design and implementation of the program.

Jan 1, 1983

One of the major objectives of cost analysis is to enable the manager to predict the financial outcomes of decisions. To accomplish this, the future costs and benefits of alternative courses of action must be determined. If care- fully used, information about past financial performance can be helpful in this analysis despite the fact that, by definition, financial reporting information is historical. In many cases, both revenues and costs need to be estimated for decision- making. For the production manager, additional revenue is a result of increased throughput or recovery of valuable material from the stream of mined material. A reduction in operating cost, although similar to a revenue increase in its financial impact, is estimated using slightly different techniques. Generally, the estimation of cost is more difficult than the estimation of revenue. Most cost estimates have two components: an estimate of fixed costs and an estimate of variable costs. As discussed in chapter 5, the total cost of an activity during a specified period can be expressed as: Total cost = (Variable cost per unit of activity) x (Units of activity) + Fixed cost or TC = VX+F

Jan 1, 1999

By K. A. Natarajan, Abha Kumari

In this paper, electroleaching and electrobioleaching of ocean manganese nodules are discussed along with the role of galvanic interactions in bioleaching. Polarization studies using a manganese nodule slurry electrode system indicated that the maximum dissolution of iron and manganese due to electrochemical reduction occurred at negative DC potentials of -600 and -1,400 mV(SCE). Electroleaching and electrobioleaching of ocean manganese nodules in the presence of Acidithiobacillus ferrooxidans and Acidithiobacillus thiooxidans at the above negative applied DC potentials resulted insignificant dissolution of copper, nickel and cobalt in IMH2S04 and in sulfuric acid solution at pH 0.5 and 2.0. Mechanisms involved in electrobioleaching of ocean manganese nodules are discussed. Galvanic leaching of ocean manganese nodules in the presence of externally added pyrite and pyrolusite for enhancement of dissolution was also studied. Various electrochemical and biochemical parameters were optimized, and the electroleaching and galvanic processes thus developed are shown to yield almost complete dissolution of all metal values. This electrobioleaching process developed in the laboratory may be cost effective, energy efficient and environmentally friendly. Keywords: Ocean manganese nodules, Electroleaching, Electrobioleaching, Galvanic interactions

Jan 1, 2003

By A. M. Al Taweel, V. K. Kasireddy

Intensive coal cleaning usually necessitates fine grinding of the feed in order to liberate inorganic constituents from the surrounding organic matrix. This however adversely affects the ability of flotation techniques to beneficiate coal. Such difficulties are mainly attributed to the increase of particle population density, the decrease in capture efficiency, and the greater tendency of inorganic components to report with the froth. A three-pronged approach was adopted in an attempt to overcome these difficulties. The aggregative flotation technique was used to reduce particle population densities and improve capture, while unconventional spargers were used to generate a wide range of bubble sizes. Use of unagitated flotation columns allowed for the maintenance of countercurrent flows in both the recovery and washing sections. The combined effect of these parameters enabled the recovery of 92% of the carbon content of coal having an average particle size of 20.5 µ m, while rejecting 85% of the ash. This was accomplished using 2 kg of fuel oil per tonne of coal in a column 2 meters high operating at 2-3 tph/m3, a capacity which compares favourably with conventional cells.

Jan 1, 1989

By J. W. III Leonard, T. E. Wilson

In addition to coalbed thickness and basic coal quality data, coal drill cores can produce design data for coal beneficiation processes. To generate design data, a coal drill core should be reduced from its original cylindrical form to a particle size distribution and composition that represents (with the possible exception of top size) a raw coal process stream. Reducing a coal core with a crushing machine rarely accomplishes this representation. This investigation employs drop-shatter impact breakage followed by dry batch tumbling in a steel cylinder rotated about its transverse axis to characterize the core in terms of first-order and zeroth-order break- age rate constants, which are indices of the propensity of the coal to degrade during handling. To reduce composition variables and conserve difficult-to-obtain coal cores, the initial drop-shatter and dry-tumbling tests were done with synthetic cores. Then, cores from three coal beds, Illinois No. 6, Upper Freeport and Pocahontas No. 5, were tested. Comparison of a crushed drill core and a drill core prepared by drop-shatter and tumbling indicated that the size distribution and size fraction composition of the drop-shattered/tumbled core more closely resembled the plant feed.

Jan 1, 2000

By S. Kesler

Rössing Uranium Limited has operated since 1976 a large open pit uranium mine and extraction plant at a remote site in the Namib desert, South West Africa/Namibia. The geology (Berning, I., et al. Economy Geology) and the technical aspects concerning mining, grade control and metallurgy have previously been described (Rössing Uranium, Mining Magazin and Whyllie, R.J.M. "Rössing Uranium reaches rated production", World Mining). The improvement of leach 'extraction has been reported in 1984 (Kesler, S.B. et. al. "Uranium extraction at Rössing") and the installation of a central process control system has been described (Kesler, S.B. et al. "The introduction of a central process system at Rössing"). At the beginning of 1983 a decision was made to develop a computer system for metallurgical plant optimisation which included mass and volumetric balances, analytical assays for up to 5 chemical elements and the costs for the major consumables. Within 10 months this computer system was developed and implemented. A large number of test runs were made and computer studies were undertaken. The metallurgical division now has a scientific tool for production; planning for actual comparison with plant results and for strategic investigations and decision making.

Jan 1, 1986

By M. Yavuz

The use of natural stones like marble is approximately as old as the emergence of human. Marble and natural stone usage of Turkey also dates back to very old times. Marble is produced in Anatolia since the ancient times. The archaeological excavations made in Anatolia indicate that the modern methods that are used for the production of marble blocks in modern world were first used by Anatolian people. Turkey is one of the oldest natural stone producers with its 4000 years of production history, starting from the Marmara Island. Therefore, the territory of Turkey possesses 4000 years of natural stone processing technology and experience. Turkey has fairly richer reserves of marble compared to other countries. This is why the rich and quality marble deposits of Turkey are resembled to the appearance of the Alpine-Himalayan marble belt of the world. Turkey has almost 40% of the total marble reserves (13.9 billion tones) of the world with 5.2 billion tones. Turkey?s marble reserve?s monetary value is worth about 2 trillion dollars. However, only 1% of these reserves are currently being utilized.

Jan 1, 2011

By Yixian Zhao

Although many ultimate pit limit design algorithms have been developed for the past one- quarter century, only the well known Lerchs-Grossmann's (LG) algorithm is capable of producing a truly optimum ultimate pit limit today. This paper presents a graph theory oriented algorithm for optimum ultimate pit limit design. This algorithm produces a true optimal solution and maximizes the total undiscounted net profit for a given 3-D block mine model. The algorithm performs much better than the well known LG algorithm, in terms of the reduction in computation time and computer memory requirements. More importantly the new algorithm is easier to understand and implement than the LG algorithm. Specifically, this paper discusses: 1) the computer representation of arcs and the rules of arc generations which dictate the formation of trees in the graph, 2) the mechanism of joint support and re-allocation, 3) the properties, the general procedures of the algorithm, and the suggested specific steps to implement the algorithm, 4) comparison between the new algorithm with LG algorithm, and 5) some experience in implementation of the algorithm and two case study results.

Jan 1, 1992

By William D. Hanson

Celestine (celestite) (SrSO4), the primary ore mineral of strontium, is present in the DeQueen Limestone Member of the Trinity Group (Lower Cretaceous) in Sevier, Howard, and Pike Counties, southwest Arkansas. Two mappable celestine beds have been identified. One bed is commonly 3-5 in. thick, but ranges up to 18 in. in thickness; the other bed is generally 2-3 in. thick. The beds are concordant within the DeQueen Limestone and were formed by precipitation from periodically restricted sea water. Reports concerning celestine date back to 1929, when Hugh D. Miser and A. H. Purdue mapped the geology of the DeQueen and Caddo Gap quadrangles. A small amount of celestine was produced in the early 1940s in Howard County. During 1941, the J. W. Hintze Company collected 1,500 pounds of celestine for testing purposes. In 1942 and 1943,750 test holes were drilled by the Bennett-Clark Company in Howard County. Afterward, approximately 90 tons of celestine was open-pit mined and shipped to Texas for processing. Since then, no mining of celestine in Arkansas has taken place.

Jan 1, 1999

By Jack E. Fraley, Robert E. Simpson

INTRODUCTION Spokane Mining Research Center (BuMines) is researching sealants for underground coal mines to: 1. Reduce sloughing of shale roofs. 2. Reduce sloughing of coal ribs. 3. Seal block stoppings against air losses. 4. Construct stoppings by spraying over jute cloth or metal lath. 5. Render incombustible in-place polyurethane foam. Originally the work was directed towards reducing sloughing of shale roofs. Many underground coal mines have shale directly over the coal which weathers severely after exposure to the mine atmosphere. Lab investigations(l, 2, 3, 4) have shown that many shales separate into layers when immersed in water or stored in a high relative humidity environment. Upon drying or after removal from high humidity, the shales continue to separate. Underground coal mines become wet in the warmer months from condensation of the ventilating air. Conversely, the mines become dry in the cooler months from evaporation. The mines experience severe shale break-up during the summer and much less break-up during the winter. Figs. 1, 2 and 3 show weathered shale roofs. in underground coal mines. Fig. 4 shows fallen shale on the entry floor. Sealing the shale reduces this sloughing problem.

Jan 1, 1974

By Stanley C. Suboleski

The increase in productivity which has been achieved in mining during the past two decades has been attained largely through the replacement of manpower with electrical power. Power demands should continue to increase, requiring electrical distribution systems to be well planned to avoid inadequate voltage levels caused by underdesign and excessive costs resulting from overdesign. To aid the mining electrical engineer in designing proposed power systems or analyzing changes to existing systems, a digital computer program has been developed. This program will analyze alternating or direct-current networks with up to 10 voltage sources, 75 loads and 300 total segments. A maximum of nine levels of voltage is permitted in the system. This project was part of a package of programs developed at Virginia Polytechnic Institute (WI) for the mining industry under sponsorship of the Office of Coal Research. Included in this package are also programs to: 1. Schedule mine production and predict cost of mining 2. Simulate rail haulage systems 3. Simulate belt haulage systems 4. Analyze ventilation networks 5. Analyze pumping networks These programs are available from the Department of Mining Engineering, VPI, Blacksburg, Virginia 24061 for a nominal processing cost.

Jan 1, 1970

By John Stroiazzo, Bernard C. Aubé

Brenda Mines, located 22 km Northwest of Peachland in British Columbia, Canada was an open pit copper- molybdenum mine which closed in 1990 after 20 years of operation. The primary concern in Brenda's tailings and waste rock drainage is molybdenum at a concentration of approximately 3 mg/L. The mine drainage is alkaline and contains little or none of the typically problematic heavy metals. Given that the waters downstream are used for municipal water supply and some irrigation, a discharge limit of 0.25 ma molybdenum was imposed with specific water quality guidelines in the receiving creek. A review of all existing and potential molybdenum removal methods was undertaken prior to mine closure. The chosen process is a two-step iron co-precipitation with clarification and sand filration at a slightly acidic pH. A 4,000 usgpm (912 m3/h) treatment plant was constructed and commissioned in 1998, at a cost of $10.5M. The successful removal of molybdenum from the drainage water is explained with details on some design innovations and operational challenges encountered during plant start-up. Investigated sludge disposal options are discussed although the long term disposal scenario has not yet been finalised.

Jan 1, 2000

By R. Hogg, P. Bunnaul

Sedimentation in highly, flocculated suspensions of fine particles, such as clays, occurs through individual settling units (flocs) that have very open structures and correspondingly low densities (typically less than 5% solids by volume). Such settling processes rapidly lead to the buildup of a bed of flocs that are essentially close-packed, with an inter-floc porosity of perhaps 50%. However, the overall solids content is no more than about 2% to 3% by volume. Consequently, the thickening process is dominated by the bed consolidation rather than by the simple settling of the individual flocs. Experimental measurements of sediment consolidation in flocculated clay suspensions indicate, for a given system, that consolidation rates are essentially determined by the solids concentration and can be evaluated using the classical Kynch treatment. However, these rates are strongly dependent on the physical, as well as the chemical, conditions of the flocculation process. Furthermore, the extent to which gravity consolidation proceeds depends on the total weight of the sediment (i.e., on the bed height and the solids concentration). The implications with respect to thickener operation and the requirements for the laboratory testing for thickener design are discussed.

Jan 1, 1993

By John L. Burnett

Field criteria are needed to help the prospector recognize a potentially expansible shale, clay, or slate. Certain criteria have proven useful in California even though the physical-chemical mechanisms of expansion are not thoroughly understood. Three conditions must be satisfied before expansion can take place, The raw material must partially fuse at a low temperature (1800-2000°F.), Concurrently a gas must form. The raw material must be sufficiently impermeable to trap the gas within the particle. Low temperature melting, which is controlled by bulk chemical composition, is difficult to assess in the field but most common shale, clay, and slate is suitable in this respect, The presence of organic carbon, the most common source of an expanding gas, is indicated by dark color of the rock, A large proportion of clay-sized particles promotes impermeability; fine grain-size is indicated by conchoidal fracture, The shape of the expanded particle is commonly indicated by the texture of the raw material. Rocks with well-developed slatey cleavage produce accordion-shaped particles; massive rocks tend to form rounded particles. Undesirable materials commonly present with expansible shale include: weathered shale; sandstone and other coarse-grained sediments; and limestone, Weathering, which is indicated by color, reduces or eliminates expansion; therefore, surface samples seldom are representative of the shale found at depth. Sandstone does not expand and will increase the average weight of the finished product, Limestone or particles of carbonate minerals can be actively harmful because they are converted to free lime (CaO) during the firing process, If free lime is present in concrete, hydration will cause expansion of the lime particles which result in surficial ?popouts.?

Jan 1, 1963

By D. M. Anderson

The current mine closure process is faced? with the formidable challenge of controlling environmental and legal liabilities that are associated with mine closure. The current level of environmental statutes and regulations, and the legal/liability considerations, has evolved through regulatory enactment of mine reclamation laws and other existing environmental laws, such as the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). Management tools and techniques to limit risk exposure and financial losses should be employed as an active measure throughout the mine life, including closure and post-closure.

Jan 1, 1995

By Solomon S. Katz

As more and more computer software is written for geological mapping applications, the users of the software are discovering the problems of transferring data between the programs, maintaining correct data and integrating maps produced last week with those produced today. One way to deal with these situations is by using a geographic information system (GIs). Last September the USGS and National Academy of Science held a 5-day GIs symposium on integrating technology and geoscience applications (USGS, 1988). It was followed in October by GEOTECH '88 (Peters and Krajewski 1989) which had a session exclusively for GIs applications in the Geo-Sciences. Editorials in Geobyte (Leonard, 1986, 1988) suggested that geographic information systems will be the next major computer programs to be adopted by the mineral industries. As far- back is 1985, the Computer Oriented Geological Society (COGS) printed An Introduction to GIs in their newsletter (Katz, 1985). About 20 years ago, a revolutionary idea occurred in the world of business data processing. It was the idea that all related data be stored in a standard format, in a single place and that all related computer application programs would use the same data.

Jan 1, 1989

By M. J. Hughes

Kaiser Steel Corporation's Eagle Mountain operations are located in Southern California at a distance of about 130 miles east of the Corporation's steel plant at Fontana, California, and at a distance of about 225 miles from the nearest harbors which are located at Long Beach and Los Angeles, California Although the Eagle Mountain ore bodies are strategically located with respect to the steel plant and the harbor facilities, they are not of a very high grade and 'the geologic nature of the deposit makes it very difficult to mine and to concentrate. The iron ores occur as partial replacement of older zones mainly within dolomites and to a lesser extent within quartzites and quartz monzonites. The alteration was extremely variable and generally resulted in the formation of pyritic magnetic which, in part of the ore body, was leached to remove the pyrite and change the magnetite to hematite. Although the overall ore body is large, a major portion of it contains sulfur in the range of 1.0% to 5.0%. Obviously, this is too high a sulfur content for direct use in blast furnace feed.

Jan 1, 1968

By P. Kolettas

The development of novel methods for the investigation of the subsoil contributes to the improvement of geotechnical research, enhances the obtained geotechnical characterization and may reduce the investigation cost by reducing the number of required tests. Non-destructive testing methods, performed either in situ (i.e. electrical tomography, seismic refraction, etc) or in the laboratory can provide initial data and perhaps estimates of rock/soil properties. This study focuses on the development of rock material properties and/or characteristics based on non-destructive laboratory testing of a number of stones, ranging from porous (bioclastic) limestones to impervious marbles. Seismic velocity measurements as well as attenuation signals were digitally recorded using a digital oscilloscope. Data were processed using a novel technique of spectral analysis available through special Matlab packages employing Fourier transform methods. More specifically, the NFFT (Non Equispaced Fourier Transform) transformation was applied to seismic waves traveling through the subsoil using the Autosignal program (by Seasolve) and the Specgramdemo program included in the Signal Analysis toolbox of Matlab 6.5 (Mathworks). Results indicate a definite relationship between the frequency content of the signal and the rock type as well as the degree of saturation of the specimen.

Jan 1, 2008