Search Documents

By J. D. Morgan

Introduction In 1987, the US economy continued to grow steadily, reaching an annual rate of $4.6 trillion in the last quarter. The value of domestically processed mineralbased materials rose slightly to $250 billion. The value of US metals rose sharply to more than $7 billion. Industrial minerals rose slightly to $18 billion recycled scrap was valued at $4 billion. Metal prices rose sharply toward year-end. A number of mining and metal companies experienced increased profitability, fostering more optimism about the future. Consumer demand strongly affects mining because the US economy is relatively saturated with long-lived products. Consumer, mortgage, and federal debt continue to rise. 244 million citizens already possess 170 million licensed motor vehicles and 100 million dwelling units. New car production fell 9% to 7.1 million units, but truck and bus production rose 9% to 3.8 million units. New housing starts fell 10% to 1.6 million units. Excess productive capacity exists not only in the US, but also in many other countries. Consequently, the US mineral industry is encountering stiff competition from others, as well as increasing competition from newer engi¬neered materials. Domestic production of plastics rose 9% to 25 Mt (27 million st) - on a volume basis, double all metals. Some 7% of petroleum goes to make petrochemicals including plastics. Imports of nonfuel mineral-based materials in 1987 were valued at $37 billion and exports at $24 billion. Imports supplied a significant proportion of total US consumption of several important mineral materials, including many classified as strategic and critical. In December, the Congress mandated that any major changes in stockpile goals be made only by law, and that the Department of Defense submit annually detailed stockpile supply/demand analyses. Concern about apartheid in South Africa continued, resulting in increasing interest about chromium, manganese, platinum-group metals, cobalt, vanadium, and gold. The National Critical Materials Council continued to monitor the US materials position. The Defense Production Act, authorizing priorities and allocations, supply expansions, voluntary agreements, and the National Defense Executive Reserve continues in effect through Sept. 30, 1989. Under the DPA, the US Bureau of Mines maintains the Emergency Minerals Administration. Further consultations were held with Canada to strengthen the North American defense industrial base. Coal production, 60% from open pits, rose 2% to 825 Mt (910 million st) valued at $21 billion. Nearly four-fifths was burned to generate 56% of US electricity. Exports included 42 Mt (51 million st) of metallurgical coal and 24 Mt (27 million st) of steam coal, with a total value of $3.3 billion. Domestic petroleum production fell 5% to 480 Mm' (3 billion bbl). Uranium mining, including recovery from phosphates, fell 4% to 5.9 kt (6500 st). Nonfuel minerals Major metals: Raw steel production - a major consumer of many minerals - rose 7% to 79 Mt (87 million st). Domestic iron ore production rose 11% to 44 Mt (48 million st), about 96% pelletized. Net imports, though, fell 8% to 11 Mt (10 million st). Raw steelmaking capacity fell 6% to 102 Mt (112 mil-

Jan 5, 1988

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Square-set timbering of stopes developed from stull support methods because veins too wide for stulling were being mined. In general, the void caused by the stoping of the ore is filled with a system of interlocking timbers. Timber framework supports the wall rock, the mining operations, and provides access. A timbered stoping method can be used in all widths of veins at any dip. The timbering can be normal and parallel to the planes of the walls or at angles to these planes. Irregularly shaped ore bodies can be worked by timbered methods. Pinching or swelling of the vein will not adversely affect the method. Timbered stoping is especially advanta¬geous where weak ground is encountered in the vein or the wall rock. The ground is unsupported only until timber sets are stood. These stopes can be filled with sand or waste when desirable. The customary method of developing a square-set timbered stope with haulage drifts above and below and timbered raises on each endline is shown in Fig. 1. The drifts are timbered the full stoping length. The raises have two compartments with the manway and timber slide in one compartment and the chute in the other. The drifts and the raises cannot be widely spaced as handling timbers is an important consideration. Stoping can begin immediately above the drift timber and continue in both directions and upward from the raise. Breasting down each blast round for only one timber set laterally is the common practice. The blasted ore falls to a lower floor where it is slushed or trammed to the chute. Drilling can proceed on the upper floor while broken ore is being removed from the stope. As shown in Fig. 2, square-set timbering may be used in cut-and-fill stopes to support the back and walls until fill is added. There are various ways of developing an ore block for timbered stoping. Fig. 3 depicts the situation for the main haulage in the vein with an intermediate drift separated from it by a sill pillar. The ore is slushed into the chute connecting the two drifts. The situation in Fig. 4 is identical to that in Fig. 3 except that no sill pillar is used. In Fig. 5, the haulage drift development is done in the footwall with crosscuts driven to intersect the ore body. The intermediate drift development is above the crosscuts with a minimal sill pillar. The main bottleneck in timbered stoping is in the timbering process. Drilling in the stope is generally held up while timbering is done. Two or three men are re¬quired to do the timbering and an additional one or two men are needed to transport and raise or lower the tim¬ber. Good organization is essential to timbering. Skill must be exercised in standing the timber to support the ground and still maintain good production. COSTS AND PRODUCTIVITIES Development and stoping costs are presented in Tables 1 through 7 for the situations in Figs. 3 and 5,

Jan 1, 1982

By H. Nematollahi

The comminution laws The grindability of the ores or minerals is an important factor that could not be deduced from their mineralogical characteristics (Testut, 1958). Many theories have been proposed to determine the amount of work required in a comminution operation as a function of the nature of material, size and shape of the minerals before and after of comminution. The most important laws are proposed by Rittinger, Kick and Bond. According to Rittinger (1867), the work is directly proportional to the new surfaces produced during the comminution. Kick (1885) believes that the work needed to produce similar modification is proportional to the volume or mass of the material. Bond, during his 25 years of experience and research, reached to the conclusion that on the average the energy required for a known comminution is between the Rittinger's and Kick's laws (Bond, 1952). According to Bond's Third Theory, the work input is proportional to the new crack tip length produced during the particle breakage, and equals the work represented by the product minus that represented by the feed. The work input is given by the following equation: [111W = 1 Owi( FP FF(1)] where W is the The energy input to the mill, (kWh/st); F is the Feed size based on 80% passed, (µm); P is the Product size based on 80% passed, (µm); and W; is the Work Index, (kWh/st) Methods to determine the Bond Work Index Various methods have been proposed by Bond to determine the Work Index. There are some problems with the Standard Bond Grindability Test: •Requiring a special mill. •Requiring a relatively large amount of sample. •Being relatively time consuming and tedious. [ ] During the recent years, numerous attempts have been made to install faster and easier methods to determine the Work Index. A complete description of these methods is presented by Yap et al. (1982). Determining the Bond Work Index by a new size ball mill During the recent years, researchers at the University of Tehran determined the Bond Work Index, using the Anaconda simplified methods by its Denver 305- x 127-mm (12 x 5-in.) laboratory wet ball mill. The equation used to calculate the Work Index for the above mill containing 16.12 kg (35.5 lbs) of steel balls is as follow: [1 _ 1-1W;=0.54x [P [)(2)] In addition, an attempt has been made to determine the Bond Work Index similar to standard Bond ball mill procedure but by a different ball mill, smaller and in consequent portable and less laborious than the Bond ball mill. Method description Just as the standard Bond grindability test, this method is a locked-cycle dry grinding and screening process that is carried out until steady state condition is reached. Test equipment The test is conducted in a special ball mill, called the New Size Ball Mill (NSBM). The mill is scaled down with a coefficient of two-thirds from the standard Bond ball mill. It measures 200 x 200 mm (8- x 8-in.) inside (instead of 300 x 300 mm or 12 x 12 in. in Bond ball mill). Just like the Bond

Jan 1, 1995

By William J. Douglas

Defining Productivity Productivity is a principal concern to all organizations - industrial, commercial, government, and academic. As a ratio of output to input, productivity measures the efficiency of an industrial process, much as thermodynamic efficiency measures the useful work obtained from the available energy consumed. However, there is one important difference. Whereas thermodynamic efficiency is a dimensionless a ratio of energies, productivity output and input are usually measured in different physical units. Nevertheless, the resulting ratio is a normalized expression for unit of output per unit of input to the process. In the early days of coal, mining was essentially a hand loading operation. There was little expenditure of alternative forms of energy within the process. Loading required expenditures of human energy on the order of 1.2 MJ/t (1,000 Btu per st). And if we accept the conventional value "you load 16 tons," the output to input ratio is 14.5 t (16 st) per manshift. In energy terms, it is on the order of 116 MJ/t (100,000 Btu per st) produced per labor Btu expended. However, the latter measure of efficiency was not meaningful in economic terms, while the 14.5 t (16 st) per manshift was significant. Since labor was the principal component of cost, it represented a direct relationship to the cost of production: [ ] Furthermore, when workers were paid directly on the basis of tons produced, the labor cost per ton was specified directly by this rate. With the introduction of mechanized loading, significant increases in productivity occurred, when measured on the basis of tons per manshift. Electric power consumed about 11.6-116 MJ/t (10,000-100,000 Btu per st). This makes the 29-GJ/t (25 million Btu per st) coal output/input ratio between 100 and 1,000. That is one or two orders of magnitude lower than hand loading. However, electric energy was quite inexpensive compared to labor, which made the mechanization economically efficient. The accepted productivity measure continued to be tons per manshift. This measure includes some of the effects of mechanization: namely, the additional manpower needed to maintain the machines and support the equipment that uses electrical energy. However, it does not consider the capital and operating costs that relate to mechanized equipment. As a result, the concept of tons per machine-shift has emerged as an accepted measure of shift productivity. The only appropriate measure that encorporates the productivity of men and machines is an economic one. The output is the tonnage per shift and the impact is the cost per shift. [ ] This is simply the inverse of the cost per ton. In addition, much flexibility is available in allo¬cating costs to the three categories. This adds a level of intangibility to the measure. The amount of information needed to obtain all of the required costs is appreciable compared to the simple matter of counting tons and workers. Furthermore, financial information relating to production costs is closely held by mining companies, so historical statistics on economic productivity are not publicly available. To extend the concept further, consider the value of the tonnage produced, to obtain a dimensionless ($/$) measure of economic productivity.

Jan 11, 1983

By R. J. Andreini

Solvent extraction is widely used in hydrometallurgical processing of uranium for purification and upgrading leach solutions prior to recovery of metal values. Conventional solvent extraction processing utilizes mixer-settler units to achieve mixing of the aqueous and organic phases. Use of mixer-settlers permits continuous treatment of feed, but the processing rate is restricted by the time required for phase separation after mixing. Because of the high-shear type mixing used in a mixer settler a portion of the organic phase becomes mechanically entrained in the aqueous resulting in loss of extractant. For this reason application of mixer-settler units is often limited by the settling area required for phase separation, especially for systems where high volume throughputs are desirable or necessary. Several alternatives to mixer-settler operations involving the use of column extractors have been proposed. Packed columns (1-2), in which organic and aqueous phases are fed countercurrently, utilize packing materials similar to those used in gas absorption or distillation columns. Extraction columns utilizing rotating(3-5) or reciprocating elements(6-7) to achieve mixing have also been developed. Van Dijek(8) originated pulsed columns, in which mechanical or air pulsing of the phases enhances the mixing in the vessel. Each of the above column processes involve varying degrees of mechanical complexity which may lead to operational difficulties.

Jan 1, 1975

By Nicholas T. Esposito

An advanced coal preparation plant has been built at Homer City, Pennsylvania, by Pennsylvania Electric Company, a subsidiary of General Public Utilities Corporation, and New York State Electric and Gas Corporation, as an alternative to utilizing flue gas desulfurization technology to meet the Federal Environmental Protection Agency and the Pennsylvania Department of Environmental Resources air quality emission regulations of 4.0 lb S02/106BTU for the two (2) existing coal-fired generating station Units No. 1 and No. 2, and a 1.2 lb S02/106BTU for the new Unit No. 3. The coal preparation plant is designed to process 5,200,000 tons of run of the mine coal annually and has a design capability to process 1,200 tons per hour via two (2) equal capacity 600 tons per hour preparation circuits.- The plant is designed to produce multi-product coal streams consisting of a middling product of medium ash and medium sulphur content, which is environmentally compatible to support operation of the two (2) existing generating Units I and 2, and a deep cleaned, low ash, low sulphur coal product capable of environmentally supporting the ambient air quality requirements of the new Unit 3 generating facility. The waste product from the process consists of high ash, high sulphur reject material. The process has the acronym MCCS (Multi-Stream Coal Cleaning System).

Jan 1, 1982

By Judith A. Marks, Deane K. Smith, Jan M. Mutmansky, Maria Klimkiewicz

The mechanical mining of coal seams where roof, partings, and floor rock are extracted along with the coal often introduces large numbers of quartz particles into the mine atmosphere. This study concentrates on the quartz properties in situ and in the airborne dust to determine how they are released from the source rock and whether they are fractured by the mining machinery. Three mines using drum-type continuous miners from different geographic areas were sampled to provide a data base. The roof and floor rocks were primarily siltstones containing 5% to 25% quartz measured by the X-ray powder diffraction (XRPD) method. Much of the work presented here is based on the morphologies of the mineral grains determined by the scanning electron microscope (SEM). The study concentrated on particles of 0.2 to 10.0 µm and on particles containing > 75% Si. Mechanically-crushed quartz particles were also examined for comparison purposes. Particle shapes from the airborne samples suggested that fractured quartz particles were rare. Particle statistics also show that the average size of quartz particles in the airborne samples were similar to the average size of all particles. The conclusion is that very few quartz particles from the source rocks are fractured during mining due to their small initial size and the protection of the associated clays.

Jan 1, 1991

By Stanley J. Gasior

Most bituminous coal mined near Eastern industrial areas requiring high Btu pipeline gas is caking and therefore unsuitable for fixed-bed pressure gasification by present techniques. If the caking property of such coal can be destroyed the resulting fuel can be gasified in a fixed bed at pressure with steam and oxygen as a preliminary step in making a high-Btu gas. To find a practical way to convert strongly caking coals of granular or small lump size to noncaking fuel was the object of this study. In previous work strongly caking coals of 1/8- to 1-1/2-inch size was converted to a noncaking coal char by treatment in a static bed in about 3 hours [1/]and coal of 18-100 Tyler mesh in a fluidized bed in about 5 minutes.[2/] An inert gas such as `steam, nitrogen, carbon dioxide, or a mixture of all three with a small amount of oxygen was used in both studies. In our work a strongly caking bituminous coal from the Pittsburgh seam of 4-8 Tyler mesh size was converted to a-noncaking form in free-fall in about 2 seconds by dropping it through a countercurrent flow of steam containing 4 to 7 percent oxygen at 1,150°-1,200° F and 300 psig. This method should also be applicable to smaller-sized material.

Jan 1, 1965

By Laurence E. Snow

The conversion to the use of commercial grade ammonium nitrate (CGAN) for use in blasting at the Utah Copper Pit of the Kennecott Copper Corporation has presented unique problems for the Drilling and Blasting Department, In order to better understand these problems, a' picture of the Bingham Pit might be helpful. Some quarter of a million tons of ore and waste must be blasted daily in order to keep thirty-eight electric shovels operating. All material is blasted by "toe holes" of 24 to 28 feet in depth, drilled from prepared drill grades and sloped so as to bottom approximately 5 feet below the bench level. Horizontal spacing of these holes averages 22 feet, with exceptions being made where faults occur in the bank. These "toe holes" are drilled by 4-inch drifter machines, mounted on self-contained mobile drill units using .3-inch starter bits and bottoming at a minimum of 2 1/2 inches in diameter, "Toe-hole" drilling amounts to about two-thirds of the total drilling. In the higher bank sections of the Mine and wherever necessary, single rows of "down holes" are drilled to 28 feet in depth and spaced, on the average 23 feet apart. These holes are also drilled by a mobile drill. "Down hole" drilling amounts to about one-third of the total drilling.

Jan 1, 1959

By Eric R. Braun

Ore reserves in the Republic mining district were nearly exhausted in 1984 when hole D-54 intersected a vein twenty- eight feet in drill width averaging 1.57 opt gold and 11.95 opt silver below post-mineral lake beds. The discovery area, termed "Golden Promise", has announced proven and probable ore reserves of approximately 372,000 tons averaging 1.0 opt gold and 4.5 opt silver, and drilling indicates another 756,000 tons of mineralized material containing 0.37 opt gold and 1.4 opt silver (Hecla fourth quarter 1986 report). This paper describes new geological interpretations made as part of a district research study sponsored by Hecla Mining Co., which led to the D-54 discovery. Important new geological concepts include: 1) re-interpretation of the volcanic stratigraphy of the district and recognition of a suite of pyroclastic rocks that are unique to the Republic graben, 2) identification of disseminated subaerial mineralization at a paleosurface that corresponds to the newly described upper contact of the Sanpoil Volcanics, 3) recognition that epithermal veins have a maximum productive vertical range of 0-500 meters, measured from the paleosurface, and 4) veins exhibit visual and geochemical vertical zoning within the productive zone with highest gold occurring at an optimal depth, which is interpreted as the average depth of hydrothermal boiling.

Jan 1, 1987

By C. E. McFarland, N. W. Kirshenbaum

Cortez Gold Mines is located about 75 miles southwest of Elko, NV. Activity in the mining district dates from 1862. The current operation developed from a 1963 joint venture of Webb Resources, The Bunker Hill Company, Vernon F. Taylor, Jr., and American Exploration & Mining Co. Three years later, the USGS discovered gold on the property following a regional geochemical survey. Drilling in 1966 and 1967 identified 3.4 million st of oxide ore grading 0.28 oz Au/st, and a 1700 st/day countercurrent decantation mill was commissioned in 1969. Heap leaching started in 1971 on low grade ore and continues to the present. The mill was shut down in 1976 following exhaustion of known oxide reserves. Mobile equipment was sold and the proceeds committed to local exploration. In 1980, a new plan of operations was developed starting with existing low grade and newly discovered mill ore. The mill resumed operations in 1981 and has been operating to date. A series of metallurgical innovations, culminating in the commissioning of a new fluid bed roaster in the summer of 1990, has enabled treatment of a series of increasingly refractory ores. Current partners in the venture are Kennecott Corporation, Vernon F. Taylor, Jr., and Placer Dome U.S. Inc., manager of the operation. Idaho Mining Corp. holds a 7.5% carried interest.

Jan 1, 1992

By M. J. Lowe

National Institute for Occupational Safety and Health (NIOSH) studies show that 43.5% of surveyed coal preparation plant workers had noise exposures exceeding the Mine Safety and Health Administration Permissible Exposure Level. Sound levels around vibrating screens in these plants often exceed 90 dB(A). NIOSH is currently developing noise controls for horizontal vibrating screens. To characterize noise sources, NIOSH researchers performed sound pressure level (SPL) measurements on a vibrating screen at their Pittsburgh Research Laboratory. The results show that the entire screen contributes to noise below 1 kHz and the vibration mechanism housings are most significant above 1 kHz. Constrained layer damping (CLD) treatments and an enclosure were used to reduce mechanism housing noise. These were evaluated using sound power level measurements according to ISO 3744. The CLD treatments reduced the A-weighted sound power level by 3.1 dB in the 1 to 10 kHz one-third-octave bands. A panel-on-frame vibration mechanism enclosure using various types of panels further reduced the A-weighted sound power level from the CLD configuration in the 1 to 10 kHz one-third-octave bands by 3.7, 4.0, and 3.9 dB for aluminum, steel, and Dynalam panels, respectively. The combination yielded a 7 dB reduction from baseline in A-weighted sound power for the same frequency range.

Jan 1, 2010

By S. A. K. Forson, Newton A. Amegbey

In order to investigate production decline in Tarkwa Goldfields Ltd., located in a tropical rain forest, amongst other areas, a health survey was conducted with the aim to see 1. The health status of the workers. 2. Which parameters carry the most information about the health situation and which of them can be applied easily during screening programmes. 3. What steps could be taken to improve the situation. In all 249 workers were investigated. A non-invasive method involving taking of body weight and arterial blood pressure was used. All subjects were required to answer a questionaire. Emphasis was placed on the history of malaria and diarrhoea within the last six months. Both management and workers co-operated fully. Another set of 110 workers from a neighbouring tyre factory were also investigated for control. Among the underground workers, the percentage body weight loss during a shift increased with decreasing body weight. Dehydration levels could be as much as 4 to 5% of body weight. This could be attributed to the fact that workers took insufficient or no water during the shift. The health status of the mine workers was generally poor and in our opinion malnutrition combined with malaria severely threatens the health and well-being of the workers. Hypertension is also a problem. An improvement in production is intimately linked with the well-being of the workers.

Jan 1, 1989

By John S. Jones, Ralph E. Brown

INTRODUCTION For more than a century, artificial ground freezing has been used for groundwater control and structural support for excavations. Most of the early uses of the freezing method were for sinking deep access shafts for mines and tunnels (1,2,3,4). More recently, ground freezing has increasingly been used for construction of large diameter cofferdams and soft-ground and mixed-face tunnels (5). Although ground freezing has been used in the past-for tunnels, it was invariably used as a last resort measure, where more conventional measures could not be used. The more recent freezing applications, however, have become increasingly cost competitive with more conventional techniques, and are now being included as part of the design concept (6,7,8,9,10,11,12). The purpose of this paper is to describe some of the more recent applications of ground freezing for tunnel construction. The paper begins with a brief description of the most commonly used freezing system, the Poetsch process. Recent tunneling projects utilizing ground freezing for structural support are then discussed. DESCRIPTION OF THE FREEZING METHOD The most commonly used freezing method is the Poetsch process, which was originally developed by F. H. Poetsch in the late 1800's. The system consists of a brine coolant, typically calcium chloride and water. Freezepipes are placed into boreholes or are

Jan 1, 1979

By Harry M. Edenborn, Richard W. Hammack

Experiments were done to determine if a mushroom compost-based sulfate reduction system could be used to treat nickel-contaminated mine waters. Sulfate reduction systems were established in columns containing acid-washed mushroom compost. Simulated mine waters containing 2000 mg/L sulfate and 50 to 1000 mg/L nickel were adjusted to pH 4.5 and pumped through the columns at flow rates between 15 and 25 mL/hr. During the first nine days of operation, virtually all influent nickel was removed in the columns by sorption and ion exchange mechanisms. The nickel removal rate then dropped to 18 to 30 mg Ni/day (7.8 to 12.8 nmol/ g-substrate/day), probably due to low sulfate reduction rates. When sodium lactate was added to the inflow, a sustained and seven-fold increase in the nickel removal rate was observed. Bacterial sulfate reduction rates measured in mushroom compost-based wetlands exposed to coal mine drainage are 2 to 20 times faster than the rates observed in this study. Low sulfate reduction rates in the columns may have been due to the inhibition of microbial activity by high nickel concentrations and the removal of labile organic compounds from the mushroom compost substrate during acid-washing. Results of this study indicate that bacterial sulfate reduction can effectively treat nickel concentrations up to 500 mg/L if labile carbon is nonlimiting.

Jan 1, 1992

By Joel Nonnweiler, Galen Samuelson Nagle

The Sacramento Regional County Sanitation District (SRCSD) has undertaken an interceptor expansion program to meet future wastewater needs associated with projected growth over the next 20 years. The Lower Northwest Interceptor (LNWI) will include over 17 miles (27 kilometers) of pipeline including 14 miles (23 kilometers) of dual force main ranging in size from 54- to 60-inch (137- to 152-centimeter) diameter and 3 miles (5 kilometers) of 120-inch (305-centimeter) diameter gravity pipeline. The estimated capital cost for the program is $331 million, with approximately $236 million in construction cost (as of November 2002). The project includes 4,700 feet (1,433meters) of tunnel including 2 crossings of the Sacramento River and one crossing of the Barge Canal, and 11 other smaller tunnel crossings beneath various creeks, sloughs, highways, and railroads. Preliminary design of the tunnels for the LNWI are discussed in this paper. The overall purpose of the preliminary design was to sufficiently define the project to allow planning level cost and schedule estimates to be performed. There have been changes to the project during final design including pipe sizes and configurations, tunnel and pipeline lengths and anticipated flows. This paper addresses only the preliminary design of the LNWI tunnels. Final design issues and changes made since completion of preliminary design are not addressed in this paper.

Jan 1, 2003

By G. M. Molinda

Some of the most difficult coal mine roof in the U.S. can be found in the Illinois Basin. Factors contributing to the high roof fall rate include: weak moisture-sensitive roof rock, high horizontal stress, and limited longwall mining. The depth of cover ranges from 90-1,000 ft and roof damage from horizontal stress can be severe. Moisture sensitive-roof rock is common above the Springfield-Harrisburg Herrin #5 and #6 seams in the Illinois Basin, and contributes to roof skin deterioration. The roof fall rate increases significantly in the humid summer months. The National Institute for Occupational Safety and Health (NIOSH) has shown, using lab and field studies, that highly moisture-sensitive roof rock can be directly correlated to poor roof conditions. Controlling the skin is the key to reducing rock fall injuries, and roof screening is, by far, the best remedy. Illinois Basin coal operators have been successful in reducing the number of rock fall injuries in recent years. NIOSH has documented best practices for screen installation which has resulted in safe, efficient operations. Other solutions to skin failure include: the use of denser five bolts per row patterns to reduce spans between bolts, systematic supplemental support in intersections, straps and large pans protecting operators, and air conditioning to remove moisture from the intake air.

Jan 1, 2008

By A. Founie

The United States continues to be the world’s leading producer and consumer of diatomite. Production of diatomite in the United States during 2005 was estimated to be 653 kt (720,000 st). This was a 5-percent increase compared with 2004. The value of processed diatomite in the U.S. was about $179 million in 2005. Production was from six companies with 12 processing facilities in four states. California and Nevada were the principal producing states. They accounted for about 70 percent of U.S. production in 2005. U.S. diatomite exports were about 144 kt (159,000 st). Imports were negligible. The internal structure and chemical inertness make diatomite an excellent raw material for filtration, absorbent and filler applications. Filtration, especially the purification of beer, liquors and wine and the cleansing of greases and oils, continued to be the largest end use for diatomite. Other applications include the removal of microbial contaminants, such as bacteria, protozoa and viruses in public water systems, and the filtration of human blood plasma. The use of diatomite as fillers and in pharmaceutical applications, including the filtration of human blood plasma, continues to increase as has its use as an insecticide base and as pozzolan. The relative rank of end uses of diatomite were filter aids, 75 percent; fillers, 11 percent; absorbents, 7 percent and other (mostly cement manufacture), 7 percent.

Jan 1, 2006

By J. H. Bassarear, J. D. Vincent

General. Copper, the first metal used by man, today is the third in consumption after iron and aluminum. Compared to these it is relatively rare, with less than 0.01% of the earth's crust copper, 8% aluminum, and 5% iron. Nevertheless. our modern civilization is heavily dependent upon copper because of its high conductivity and resistance to corrosion, ease of working, durability, wide range of properties by virtue of its readiness to form alloys with other metals, and its attractive colors and texture that make it so desirable for many crafts and arts. These attributes explain why copper is chosen for a long list of uses, including electrical wiring, switchgear, and bus bars; piping, roofing, and siding; and manufactures of brass, bronze, and other alloys. The fact that copper ore is mined in nearly all parts of the world is significant. Its importance is shown in Table I, which gives figures on world production from 1968 to 1977. In the Free World, North and South America and Africa are preeminent. The table also shows the generally upward trend of production in this period; accurate figures for 1978 and 1979 from the same source are not yet available (1980), but it is certain that major environmental, economical, and political factors continued to disturb the industry in those years and into 1980.

Jan 1, 1985

By Yuuichi Umeki, Yuusaku Tominaga

In order to keep good air condition in any specific branch such as coal face and/or heading in an underground coal mine, effective factors of all the branches with respect to the specified branch have been investigated, using computer simulation. Main results of the paper are as follows; 1) A branch in a network is classified to one of three classes of effectiveness to increase, to decrease and not to change airflow rate in the specific branch by altering aerodynamic resistance in the branch. 2) Distribution of position of branches, belonging to each class, related to a specific branch is one of the macroscopic characteristic of a network which is the inherent property of every network. 3) A relation of the aerodynamic resistances of any two branches to keep a constant airflow rate in the specified branch is shown as a monotonous curve. 4) Ventilation transition diagram with the rate of airflow in the two branches as coordinates, and for different rates of airflow in the specific branch as the parameter, is found to be straight lines. 5) Existing range of airflow rates In the specified branch is given as a parameter in the enclosed area in the ventilation transition diagram. Moreover, an expert system to assist ventilation control using a transition diagram of airflow rate is introduced in this paper.

Jan 1, 1991