Search Documents

By Stewart R. Wallace

In the spring of 1959 while visiting the offices of the US Geological Survey (USGS) in the Denver Federal Center, I had a chance encounter with Paul Theobold, a former but, at that time, casual associate. Paul mentioned to me the results of his work on stream sediment geochemistry (Theobold and Thompson, 1959). Using panned concentrates, Theobold and Thompson had discovered a tungsten anomaly in Clear Creek and followed it upstream to its source on Woods Creek, a small tributary to the West Fork of Clear Creek. The specific source was a debris cone about 0.8 km (0.5 mile) upstream from the mine yard at the Urad molybdenite deposit. Because of the genetic and zonal association of tungsten and molybdenum at Climax, I found this very interesting. Accordingly, I related this information to Robert Henderson, general manager of western operations for Climax, and asked his permission to do some follow-up work. He, in turn, telephoned Frank Coolbaugh, the president of Amax, telling him of my interest and saying that, "Climax would take care of it." On my first visit to Urad, my companions (Dave Jonson, Bruce MacKenzie, and Dick Baker) and I were confronted by a "Cousin Jack" caretaker who made up for his diminutive stature by a "pistolover" that hung down almost to his knee and by a watchdog that was one-half wolf and one-half mean sled dog. We retreated discretely to Clear Creek and then climbed up the "back" side of Red Mountain by separate routes, across the ridge crest, and part of the way down the "front" side, sampling as we went. Although much of the ground was covered with snow, we found lots of puzzling but friendly looking rocks and the geochemical results were interesting. A geologic map of central Colorado showing the location of the Urad-Henderson and Climax deposits is shown in Fig. I.

Jan 1, 1991

By Donald A. Dahlstrom

INTRODUCTION Solid-liquid separation is an important and many times a critical step (or steps) in a mineral or coal processing plant. Some examples of typical critical separations are as follows: 1. Operating a seven to eight stage CCD thickening circuit to re¬cover almost all of the caustic and alumina trihydrate values in an alumina plant. This must be accomplished with highly scaling slurries, starting temperatures of over 100°C and operate on a closed circuit system. 2. Making a filter step operate to produce a proper moisture for the balling step so that the pellet furnace can produce a proper product. Bentonite addition must be minimized and a good quality filtrate must be maintained to prevent abrasion of the internal parts of the filter. 3. Operating a closed water system in a coal washing plant so that reclaimed water containing less than one percent suspended solids is produced for reuse to maintain beneficiation ef¬ficiency. Refuse solids must also be thickened so that they can be effectively dewatered to meet state disposal requirements. 4. Recovering phosphoric acid values from a slurry containing gypsum and other gangue solids at an elevated temperature. This must be done while minimizing wash water and maximizing P2O5 re¬covery while simultaneously minimizing scale problems. While solid-liquid separations are important to overall performance in the processing plant flowsheet, it is also a significant factor in plant costs. Capital and operating costs for all the solid-liquid separation steps (includ¬ing water reclamation for reuse) in such plants are probably between 10 and 20%. Energy consumption can also be important in these separations. For example, in the copper concentrator, it is the third largest category in energy consumption, after comminution and flotation. Obviously, solid-liquid separation steps in a plant demand proper atten¬tion in design in order to achieve both optimum performance and cost. Simultaneously, knowledge of funda¬mentals are important to improve results in existing plants.

Jan 1, 1986

By N. Sheikh

In galena flotation, lead ethyl xanthate, Pb(EtX)2, is precipitated and is physically adsorbed in the form of multilayers on the chemically adsorbed first layer of Pb(EtX). 1,2) The solid particles are coated with layers of Pb(EtX)2 in heterogeneous manner over surface areas possessing both anodic and cathodic character (3,4) It is anticipated that the mode of formation of Pb(EtX)2 and the number of ions present, together with stable or unstable by-product species, have great influence on the surface characteristics of galena. The information obtained from a study of these parameters may have important practical applications in flotation. Lead ethyl xanthate is sparingly soluble in water. The metal and xanthate ions released to the aqueous solution during its dissolution undergo various types of reactions depending upon the pH values of the system. Extensive work (5,6) has been carried out to elucidate the mechanism involved in acid decomposition of xanthate ions. Different decomposition paths (7,8) have been proposed for the hydrolytic decomposition of xanthate in neutral and alkaline solutions, The concentrations of lead ions vary due to a number of chemical reactions, regulated by the pH and the temperature of the bulk phase. The hydrophobic character of Pb(EtX)2 may change with the nature of chemical reactions. Some of the numerous by-product species in solution may adsorb on the solid and change the properties of surface film either favourably or adversely. The flotation performance of galena, therefore, may depend to a considerable extent on the physical and chemical stabil¬ity of Pb(EtX)2 layers. Since little work has been reported in literature dealing with the stability of Pb(EtX)2 and its correlation with the flotation of galena, attempts have been made In this study to evaluate the behaviour of freshly formed Pb(EtX)2 in aqueous systems at various pH values.

Jan 1, 1971

By Ajay Mahajan, Manoj Mohanty, Vishal Gupta

Modern coal processing plants utilize multiple cleaning circuits to efficiently beneficiate different size coal fractions of run-of-mine coal. An older plant optimization approach is to maintain average product quality from individual cleaning circuits at the same level as the given product specifications for the overall plant. However, many past studies indicate that the equalization of product quality approach fails to produce the maximum plant-yield. A newer approach, known as equalization of incremental product quality, requires that the incremental product quality obtained from each circuit be maintained at the same level to satisfy the overall plant product quality. This approach ensures the maximization of plant yield while satisfying a single product quality constraint. However, while dealing with multiple product quality constraints, this approach by itself may not be sufficient to obtain the desired maximum yield. For the simple reason that the dirtiest particle (or group of particles) with respect to one quality constraint may not be the same particle (or group of particles) with respect to another quality constraint, the mass yield versus product quality relationship generated by equalizing different incremental product quality may not be exactly the same. Therefore, an additional search technique has to be utilized to determine the global-maximum value of plant yield. Thus, the main objective of this study was to utilize an emerging optimization technique, known as genetic algorithms (GA) to maximize plant yield while satisfying multiple product quality constraints. The maximum plant yield obtained from this approach was nearly same as the maximum yield obtained by the incremental product quality approach while satisfying one specific product quality constraint. The GA was applied on a coal preparation plant that utilizes four circuit operations - heavy medium bath, heavy medium cyclone, spiral and froth flotation. The results showed that using GA as an optimization process gives 2.56% higher yield that will result in additional revenue generation of $5,120,000 per annum than average product quality approach.

Jan 1, 2005

By William C. Cox, Ronald E. Heuer, Jean-Michel Loignon

The Gatineau shaft described in this paper was an excavation of about 38 m diameter and 21 m depth constructed in Gatineau, Quebec, across the Ottawa River just north of Ottawa, Ontario. A large sewage lift pumping station-was to be constructed in this excavation. Subcontractor for the shaft excavation and initial support was Beaver Underground Structures Ltd., of Dorval, Quebec. Mr. William C. Cox of Beaver conceived the idea for the support system used in this excavation, and was responsible for the construction activities. Initial analysis and design concepts for the lining system were developed by Mr. Ronald E. Heuer. Detailed lining design and construction monitoring were the responsibility of Mr. Jean-Michel Loignon. Geologic conditions indicated by two borings within the shaft area are illustrated in Fig. 1. The shaft excavation would be in the sensitive Leda silty clay. The clay is of stiff to very stiff consistency, with an insitu vane shear strength averaging about 115 KPa (2400 psf) and a reported low value of about 87 KPa (1820 psf). Low strength values were from the middle of the clay layer, with higher strengths at the top and bottom. Average shear strength at the level of the base of the excavation was about 137 KPa (2860 psf). Remolded vane shear strength averaged about 20 KPa (420 psf), with a reported low of 13 KPa (270 psf). Based upon average strength values, the clay sensitivity is 5.8. The clay has an average water content of 53% (range 43 to 66%), which is near its liquid limit (average 56%). The clay unit weight is about 1760 kg/m3 (110 pcf). Underlying the shaft site at shallow depth is limestone bedrock within which the piezometric head is approximately equal to the original ground surface elevation. For shaft support, a -cast-in-place concrete wafer system was considered, but was discarded because of time restrictions imposed by concrete placement and curing. The support system selected utilized liner plate with light steel walers closely spaced. The light rib

Jan 1, 1983

By B. M. Sadashiva Murthy

Increasing quantities of nutrients and pesticides in agricultural runoff in recent years has caused the more developed western nations to become concerned about diffuse agricultural pollution. Thus, the problem of diffuse pollution is of greater importance and concern for any integrated water quality management programme. The above mentioned sources and activities causing pollution to groundwater cannot be completely avoided. The best solution is to entail a firm understanding of the principles of solute transport through porous media. The complex factors that control the movement of contaminants in porous media and the resulting behavior of contaminant plume are usually intricate to assess because of interaction of many factors such as dispersion, advection, sorption, degradation, volatilization, etc. As accurate quantification of solute under field conditions is inherently difficult, the fate of nitrate and phosphate have been analyzed in laboratory column and channel studies. From the analysis of the breakthrough curves, the dispersion co-efficient for nitrates and phosphates through sandy soil was found to be 0.262 m2/d and 0.114 m2/d for column studies, 0.321 m2/d and 0.231 m2/d for channel studies respectively. The column studies revealed that the concentration of nitrates and phosphates increased steadily in the first few days (around 5 days) and then it increased rapidly after 8 to 10 days. However, it attained equilibrium after 20 days. Similarly, the channel studies revealed a steady increase in concentration of nitrates and phosphates in the first few days (1 to 2 days) and rapid increase up to 15 days and there after it attained equilibrium. In the study, one-dimensional analytical model has been developed which include the advection, dispersion, and a characteristic term called ?total elimination rate?. The comparative study of column and channel studies, and model output (in which the term total elimination rate ?K? is considered as zero) exhibited a variation of 30 to 50 % in leaching characteristics of pollutants (nitrates and phosphates).

Jan 1, 2008

By Dan Plazak

Discussion by Dan Plazak The authors are to be congratulated for presenting a simple and practical tool for quick estimates of ground water flow rates. At the risk of detracting from the simplicity of the method, I would like to suggest a slight refinement to the equation as presented. As the authors noted, the Jacob-Lohman equation (1952) assumes confined-aquifer conditions. To use confined-aquifer equations in water-table aquifers, Jacob (1963) presented a correction to convert water-table aquifer drawdowns [Ahw] to equivalent confined aquifer drawdowns [Ah,: 2] [Ah Ah = Ah - w(1) Cw 2H where: Ah, = Drawdown in confined aquifer: Ahw = Drawdown in water-table aquifer and H = Original saturated thickness of aquifer] Substituting the above in equation ( I) of Hanna. Azrag and Atkinson [4nT Ah - 2H ) Qj2.25 T t(2) 1 nr2 S W] Since the above expression predicts lower pump rates, it causes the Jacob-Lohman equation to agree more closely with appropriate analytical and numerical models. Figure 1, adapted from Fig. 5 of Hanna. Azrag and Atkinson, illustrates the closer agreement of the modified equation to their numerical model, as reflected in Qm/QJL ratios closer to unity. The agreement improves particularly as drawdown [Ah] becomes large in relation to aquifer thickness H. An additional advantage of the modified equation is that Hanna, Azrag and Atkinson's correction factor C is much more stable as pit depth increases. Assuming, as did Hanna, Azrag and Atkinson, that their numerical model is an accurate predictor, it is clear that the modification incorporated in equation (2) improves the accuracy of preliminary estimates of ground water flow to a pit.[ ] References Jacob, C.E and Lohman. S. W.. 1952, "Nonsteady flow to a well of constant drawdown in an extensive aquifer." Transactions, American Geophysical Union. Vol, 33, No. 4. pp. 559-569. Jacob. C. E.. 1963, `Determining the permeability of water-table aquifers,' USGS Water-Supply Paper 1536-1, pp. 245-271

Jan 1, 1995

By Paul D. Dupree

Introduction Trapper mine is a dip-line strip coal mine, located about 10 km (6 miles) southwest of Craig, CO. The mine provides the Craig Generating Station, operated by Colorado-Ute, with about 2 Mt (2.3 million st) of coal annually. The Trapper mine is situated on a hillside that climbs in elevation from 2 to 2.5 km (6500 to 7400 ft) at average grade of 15%. The coal seams dip at about 16% down-grade and they outcrop near the top of the hillside. They exceed maximum stripping depth in 1 to 1.7 km (3500 to 5500 ft) of pit length. Stripping in the three existing pits is performed with three Page 752 23 m3 (30 cu yd) walking draglines. Two of the pits are currently being cast blasted. Until the active cut, the Derringer pit was cast blasted only where the lower mined seam exceeded stripping capabilities and the pit was a single seam operation. Now, a 9-m (30-ft) interburden bench has been incorporated into the stripping plan. This bench protects the first seam of coal from shear when the overburden is cast blasted. The cast blasted section of the 1.6 km (53,000 ft) long pit has been increased from the 457 m (1500 ft) casted previ¬ously to 1 km (3500 ft). High speed films show the coal losses due to shear of the blast are minimal. The pit width in Derringer pit is 61 m (200 ft). This is necessary for efficient spoil side stripping of a relatively thin interburden in the two-seam section of the pit. The Enfield pit is entirely cast blasted. The single seam pit is 46 m (150 ft) wide, 1.1 km (3600 ft) long, and varies from 15 and 46 m (50 and 150 ft) in overburden depth. The overburden strata at the mine consists of medium-hard layers of sandstone, shale, and

Jan 1, 1987

By John F. M. Sims, Charles B. Green

Introduction The gold rush to the Canadian Klondike and then to the Alaskan gold camps is legend to Americans. The early years of the century also saw flourishing hard rock mining at the famous Treadwell and Alaska Juneau gold mines and the bonanza Kennecott copper mine. Over the last two decades, rich discoveries of copper, cobalt, zinc, lead, molybdenum, tin, and silver have furthered Alaska's reputation as a storehouse of US minerals. Alaska may also contain large commercial deposits of chromite, platinum, and nickel. Yet in 1984, with the exception of the Usibelli coal mine and several hundred small placer gold mines, Alaska's mineral potential remains largely undeveloped. Uncertain 70s The 1970s were years of uncertainty for the mining industry in Alaska. The discovery in 1968 of a huge reservoir of oil and natural gas in Prudhoe Bay brought the land claims of Alaska's natives to national attention and focused interest in Alaska's resource wealth. The Alaska Native Claims Settlement Act of 1971 (ANSCA) created the regional native corporations and granted them selection rights to some 178 000 km2 (44 million acres) of Alaska's 1.5 Gin' (375 million acres) - about 12% of the state's land area. The native land selection process would take years. During this time, the status of much of Alaska's land was in question. Additionally, section d(2) of ANSCA provided for the conversion of an undetermined amount of federal lands into conservation units. These consist of parks, scenic rivers, national monuments, and wildlife refuges. The debate over the d(2) lands was long and acrimonious. National conservation groups lobbied to include as much acreage as possible within restrictive classifications, regardless of its mineral or energy potential. The process was polarized into a preservation-versus-development struggle. To many Alaskans, what was at stake was the ability to develop a viable independent economy, rather than an ongoing role as economic wards of the federal government. The resulting compromise was the Alaska National Interest Lands Conservation Act of 1980 (ANILCA). ANILCA resulted in the placement of some

Jan 1, 1985

By E. G. Williams

Underclays and shales are two natural resources associated with the coal measures. Underclays are widely used as the raw material for refractory, semi-refractory, and face bricks. Shales are useful for sewer pipe and lightweight aggregate. This study concentrates on the geologic controls over the properties of shales for use in the manufacture of lightweight aggregate, and the geologic controls over the properties of underclays for use in the manufacture of bloating ladle refractories. The industrial processes are similar in that both involve the trapping of a gas phase to cause bloating. They differ in that the bloating of lightweight aggregate occurs at lower temperatures (1000-1200°C) than ladle bricks (1350°-1470°C). Lightweight aggregate bloats during an initial rapid firing. Ladle bricks are manufactured by slow firing at 1100°C for up to 80 hours. Bloating occurs when these bricks are reheated to 1350°C . Bloating shales are those which expand twice or more times their original volume during fairly rapid firing. Commercial bloating is usually done by rotary kiln processing or sintering; in both cases the firing rate is much faster than the experimental rate (5/8°C/minute). Bloating results from the entrapment of gasses which are evolved during firing. The material must have adequate viscosity to trap gas bubbles throughout the temperature range of bloating. The finished product contains a high percentage of closed pores with a bulk density between 35-75 pounds per cubic foot. Expanded shale finds its most important use as a substitute for heavy concrete aggregate (crushed stone, sand and gravel) where low bulk density is desired property. The extent of bloating in lightweight aggregate is a function of the mineralogy and chemistry of the shale. Figure 1 shows a corner of the three phase diagram, kaolinite-quartz-(illite and chlorite). Several areas on the diagram are outlined which contain predominantly marine shales, fresh and brackish water shales, and underclays. Each sample was rapid fired and the resulting expansion was plotted on the phase diagram.

Jan 1, 1973

By John R. Woodcock

The Kitsault molybdenum deposit lies along the east margin of thecoast Batholith Complex near the head of the fiord of Alice Arm. It is 800 km (497 miles) northwest of Vancouver, British Columbia. The deposit is located on Lime Creek 8 km (5 miles) from the coast on a wide dissected upland valley at an elevation of 600 m (1969 ft). It is an area of coastal rain forest with high annual precipitation and extremely high winter snowfall. Although the area is of high relief, outcrops are largely restricted to ridges and canyons. Most of the area is covered by the coastal vegetation or wet swampy upland areas. The south edge of the molybdenum deposit was exposed in a sharp canyon; however, outcrops over the remainder of the deposit were largely restricted to a few small exposures of resistant hornfels. The mineralization is related to an elliptical porphyry stock of 52.3 m.y. age which intrudes argillites and microgreywackes of the Late Jurassic Bowser Group. A circular zone of alteration, with a diameter of about 700 m (2297 ft), occurs in the north end of the stock and the molybdenite mineralization is concentrated in the outer parts of this zone of alteration. Thus, the northern part of the mineralization occurs partly in the hornfels and partly in the stock, whereas the southern side of the ring of mineralization cuts across the middle of the stock. Zoning within this system includes a central circular area of almost complete replacement of quartz plus K- feldspar and this grades sharply outward into a phyllic zone. Clay alteration is largely localized along late faults. The ring of molybdenite mineralization is partly overlapped and partly surrounded by a zone of pyrite mineralization. Some chalcopyrite is coextensive with the pyrite zone. Late polymetallic veins fill two conjugate fracture sets. These quartz veins contain galena, pyrite, some chalcopyrite, and a number of lead-bismuth sulfosalts.

Jan 1, 1991

My first regular job nearly fell through. My parents were spending the summer in California and I joined them at Lake Tahoe where we were guests at the lovely summer home of the Reids of Belmont. The time went quickly but I was eager to start work so I left for Bisbee a few days earlier than I had arranged. This was lucky, as just after I left a letter came from Gene Whitely, chief engineer of Calumet and Arizona, saying that because of the depressed copper industry there would be no job. I reached Bisbee on a Saturday morning, a day or two before my 23rd birthday, July 27, 1907. The brown plastei four-story Copper Queen Hotel was only a few steps from the station where the branch railway ended. I rented the cheapest room on the top floor and, of course, there was no elevator. I soon learned how to walk up the mile of switching tracks to the Calumet and Arizona office at the Irish Mag mine. I was horrified when Whitely told me about his letter telling me not to come, but since I had not received it he relented and said I could work for a short time anyhow. I was to start at 7:30 the next Monday morning, "holding the ignorant end of the tape”-in other words being surveyor's assistant, at $100 a month. Hours were from 7:30 to 5: 00, seven days a week. I spent Sunday walking around the town. I rented a room at the Royal Lodging House, which was cheaper than the hotel. It smelled strongly of carbolic acid but that meant no bugs. Compared with Cobalt or Cripple Creek, Bisbee didn't seem unattractive. The main street, with one or two-storied stores and saloons, followed the bottom of the canyon with high steep hills on both sides. My lodging house was on a rock in a narrow spot in the canyon, discouragingly called Tombstone Canyon. Chihuahua Hill, opposite the

Jan 1, 1976

By Donald C. Rotherham

The Endako, British Columbia, deposit was initially discovered in 1927 by two local men, Charles H. Foote and Alf Lagdon, who were at that time on a hunting expedition. Four mineral claims were located to cover an area of quartz-molybdenite float that was centered on two small ridges. They subsequently uncovered a 0.5-m (1.6-ft) wide vein on which an inclined shaft was sunk to a depth of 8.3 m (27.2 ft) in 1934. Additionally, a short adit was driven to intersect another vein. Numerous trenches and small pits were also dug. Small test shipments of vein material from this early work were sent to G.S. Eldridge and Co. in Vancouver for metallurgical testing. A concentrate assaying 89.2% MoS, was produced with a recovery reported as 93.3%. The concentrate was essentially free of copper, arsenic, and phosphate. The property was examined by many geologists and engineers during 1934 to 1952, but the only work done was undertaken by the owners in order to maintain their claims in good standing. In 1952, Kennco Explorations (Canada) Ltd. carried out a limited program of bulldozer trenching, sampling, and geological mapping before relin- quishing their option. In 1956, American Standard Mines Ltd. acquired an option on the property, but no assessment work was apparently recorded and the property was allowed to lapse. The key claims were restaked in 1959 by C. Riley and H.T. James of Vancouver. The property was optioned from the new owners by Andrew Robertson in July 1961, and a small amount of trenching was conducted. Robertson, on behalf of his own company, R & P Metals Corp., reoptioned the property in January 1962. The initial results of this work were favorable and justified further exploration. The additional finances required to continue the program resulted in the formation of Endako Mines Ltd. (N.P.L.) on June 21, 1962. Field work by R & P Metals and the first Endako Mines exploration was directed by Bob Couts.

Jan 1, 1991

By G. L. Bloomsburg, E. G. Zahl

INTRODUCTION During the past decade, disposal of mine and mill waste material has become an increasingly important issue. Problems of structural stability and seepage effects on stability have been well addressed, and significant technological advances have been achieved [(1-4)]. The primary problem currently facing industry in the waste disposal area is environmental protection. The greatest environmental concern is over the amount of seepage or leachate entering the ground or surface water systems. Methods to determine the quantity of water seeping from a tailings pond have also been covered in the literature [(5-23)]. However, much further work is necessary to fully implement these techniques to evaluate tailings pond performance and accurately predict the various influences of disposal management on seepage from mill tailings. This study is an effort to develop those necessary techniques. The partially saturated method of analysis which is discussed here is applicable to most situations involving seepage from waste piles. In a conventional type of tailings pond, a slime layer is ordinarily built up under the ponded area. This material will consolidate slowly from capillary pressures and the weight of material deposited above it. In situations where this consolidation results in a slime layer of lower permeability than the native foundation soil, a partially saturated flow condition will usually exist in the native soil. This will result in a smaller quantity of water entering the ground-water system than would be predicted by saturated flow analysis. The finite-element program used in this study was originally developed by Neuman [(17)] and is called UNSAT2. The program will analyze problems of saturated or unsaturated, steady or nonsteady flow and can be used with a variety of boundary conditions such as constant flux, constant pressure, maximum flux, minimum pressure, and with infiltration, evaporation, and seepage surfaces. The maximum conditions are controlled by exterior factors such as atmospheric conditions; but the actual flow in the porous media is determined by properties of the porous media. In this test, the computer code was used

Jan 1, 1980

By C. S. Caldwell, L. C. Thompson

Mine closure and reclamation issues have evolved over the past several years becoming further complicated by stricter standards and by the cmrent economic climate and price of gold. Many mine permits are calling for more stringent remediation of spent ore heaps and tailings. Leachate solution water quality must meet strict discharge criteria for multiple parameters besides cyanide at mine closure. Closure standards are more difficult to meet and most mines do not have an increased budget at the end of mine life to deal with the falling standards. These issues make additional gold recove1y at the end of mine life a critical problem in financing some closure operations. Another issue is the length of time that must be budgeted for heap rinsing operations. Innovative biological processes developed and applied by Pintail Systems, Inc. at numerous mine closures have indicated that bio-processes can significantly enhance gold recovery dur­ing heap cyanide bio-detox over the recoveries expected from rinse operations. If heap rinsing can be eliminated or reduced and if gold recovery can be improved at the end of mine life, many mine closures may be possible with processes that pay for themselves or generate profit. Additional advantages of the bio­detox technology is that it can be engineered to treat multiple contaminants besides Weak Acid Dissociable (WAD) cyanide. Other contaminants treated in heap process solutions include nitrates, ammonia, heavy metals, thiocyanate and total cyanide. At the Cripple Creek and Victor Mining Company Ironclad Mine near Victor, CO, 5 million tons ofrinsed, heap leached spent ore were biologically detoxified to reduce cyanide content, enhance gold recovery during bio-detox and to reduce dissolved metals in heap leachate solutions. During the bio-detox treatment period a substantial improvement in gold recovery allowed the detox oper­ation to operate as a profit center. Final gold recovery was at least twice what was expected from a normal rinse operation.

Jan 1, 1998

By Richard M. Crowell, John W. Shield, Todd J. Harvey

Facing lower gold prices, gold mine operators throughout the world are seeking ways to reduce costs for treating refractory sulfide ores. Many gold mines, currently producing oxide ores, have underlying refractory sulfide deposits and the operators could extend the mine life by processing these sulfides. Fortunately, oxidation technologies for refractory ores need not be complex nor costly. GeoBiotics, Inc. has developed heap biooxidation technologies (GEOCOAT™) for treatment of refractory gold ores and concentrates. GEOCOATTM uses simple low cost unit operations common to heap leaching of gold and copper ores. The cost effectiveness and flexibility of GEOCOAT™ heap biooxidation allows mining companies to expand operations to include refract01y ore. In addition, GEOCOAT™ can be utilized to supplement or replace existing oxidation processes such as roasting, autoclaving, or agitated tank biooxidation, and to treat a lower resource grade than is currently economic. The GEOCOAT™ technology involves coating sulfide concentrates onto sized support rocks and biooxidizing the sulfides in a heap configuration. After biooxidation the concentrate is stripped from the support rock, neutralized and leached in conventional cyanidation facilities. Ashanti Goldfields Company Ltd. (AGC) produces over 885,000 ounces of gold per year from oxide and refractory ores at its Obuasi operations in Ghana. Refractory flotation concentrates are treated in roasters and in the world's largest stirred tank biooxidation facility. In August 1998, AGC and GeoBiotics jointly constructed and operated a field demonstration heap of the GEOCOATTM process at the Obuasi operations. The heap contained I 082 tonnes of support rock and 125 tonnes of concentrate. The heap was approximately 19 meters square at the base and 3.8 meters high, and ran for 88 days after which the concentrate was reclaimed. Average gold recovery after biooxidation was 91.5% with a NaCN consumption of 8.6 kg/t. Baseline gold recovery by direct cyanidation of the concentrate was 53.8%.

Jan 1, 1999

By David Muir, Slobodanka Vukcevic

Gold is commonly associated with copper minerals, particu­larly in the more geologically recent rocks of Northern Australia, Chile and the Pacific Rim. Traditionally, oxidised copper-gold ores are selectively mined and processed for gold by cyanidation, ensuring that levels of reactive copper in the ore are kept low to minimise cyanide consumption; whilst sulphide copper-gold ores are floated and gold is ultimately recovered as the by-product from copper smelting and refining (La Brooy, 1992). Very few process­ing options exist for treating copper ores which cannot be selec­tively mined or floated, and for treating floation tailings which often contain significant gold (Muir et.al.,1989). The ammonia-cyanide leach system stands out as a unique method of selectively extracting gold without copper using economic levels of cyanide (1-2 kg/t NaCN) and ammonia (1-5 kg/t). Although first patented in 1904, it proved difficult to control and predict per formance with different ores. However, recent research and development in Western Australia by Ruane (1991), Hayes and Corrans (1992), La Brooy et.al.(1991), Muir et.al.(1993), Muir and La Brooy (1993), has led to an under­standing of the mechanism, and the commercialisation of the process at the Paris Dump (W.A.), Akjoujt (Mauritania), and in the Eastern Transvaal (Laxen,1994). Efforts are now underway to pilot and develop a tailings treatment plant at Telfer following successful laboratory trials. To date, process optimisation has relied on trial and error and large numbers of tests covering a range of conditions. Thus the results are specific to the ore. At Murdoch University, process optimisation is now focused on measuring and control­ ling Eh, pH, NH3 [Cu(II)], and Cu-CN species at the optimum levels identified from the recent mechanistic studies. In this way, the optimum composition required to process any ore should be readily established and maintained.

Jan 1, 1995

By C. Tsamantaki

Water-bentonite suspensions exhibit a yield stress which is defined as the minimum applied stress for flow. Considerable debate exists about the yield stress being a material property, hence different measuring methods should give similar answers, but several investigators have demonstrated that it is an engineering reality. Yield stress is normally estimated indirectly from the rheogram obtained with a viscometer following an extrapolation to zero shear rate (the dynamic yield stress), but the technique may be prone to errors because of slip flow. Direct measurements, not prone to such errors, rely on an independent assessment of the yield stress, normally carried out with the vane method (the static yield stress). In this paper results are presented and compared regarding the yield stress of 14 different water-bentonite suspensions measured using both the direct and the indirect methods. In order to obtain a wide range of yield stress values, two different types and two concentrations of bentonite at various pH were tested. Rheological data were obtained using a rotational speed viscometer and a yield stress vane measuring device. Measured vane yield stress values ranged from 5 Pa to 83 Pa. Rheological data collected with the rotating viscometer were fitted using various conventional techniques (interpolation, linear and non-linear regression analysis) as well as using a golden section yield stress search methodology based on Herschel-Bulkley model, developed in house. The vane instrument measures directly the yield stress of the suspensions and requires no further data handling. A comparison of the measured values of the yield stress with the direct and the indirect method is then made for the water-bentonite samples. Not very large differences are observed among different techniques and the variations are discussed. Similar data from literature are also analyzed and the comparison shows that differences on the various estimation methods are much larger than the differences observed in this study.

Jan 1, 2006

By D. O. Miller

The effective staffing of personnel in a new concentrator facility is a key factor in the success of the operation. By selectively recruiting quality individuals, a company is in a strong position to build a positive work ethic which will become an integral part of it's culture. And culture, which is a set of standards that all employees work to uphold, is that intangible as- set that often determines whether or not a company will survive during difficult economic times. Recruiting and placement of personnel in a concentrator facility requires an emphasis on planning. Management must carefully analyze the following elements when designing a hiring plan: 1. Number of positions 2. Hiring schedule (timetable) 3. Critical positions 4. Lead-time for trainee posit ions 5. Characteristics of the ideal workforce This presentation will focus on a proven system that is efficient (and yet simple) for achieving a new concentrator facility's manpower requirements. IDENTIFYING THE STAFFING NEEDS As previously stated, the key to staffing is planning. Management will find that a basic manpower chart will provide the hiring schedule to meet deadlines. In fact, this system begins with a manpower chart (Figure 1). The chart basically works in reverse of the hiring requirements: the last scheduled hire is the first job on the list. This approach ensures that the company will not find itself compressed against the facility start-up date. A cardinal rule in recruiting a workforce is to allow sufficient time to orient and train employees to the procedures and culture of the system. Problems in selection of personnel begin when the hiring program is short-circuited for timing reasons. The quality of employee selected invariably suffers accordingly. The second section is the key to the success of the manpower program. This is the latest date by which a formal recruiting effort must begin in order for the hire date to be met. Leadtimes are usually as follows: 1. 90 days for company transfer positions 2. 60 days for experienced new hire positions 3. 30 days for trainee positions

Jan 1, 1986

By S. A. Tims

INTRODUCTION The Falconbridge mine ore body extends about 1.6 km (1 mile) in length and the deepest developed ore is on the 6050 level below surface. The ore zone varies in width from a few inches to over 30 m (100 ft) and the average width is 4.9 m (16 ft). Access levels are driven in the ore at 53.3-m (175-ft) intervals. The principal method of mining is overhand longitudinal cut-¬and-fill. Prior to 1962 timber square-set stoping as a secondary extraction method was used for about 15% of the total production. Undercut-and-fill was intro¬duced at Falconbridge in 1962 as a potential replace¬ment for the square-set method in heavy ground. The undercut-and-fill method was developed by Inco in the 1950s, its principal application being to transverse pillar mining. Falconbridge made modifications to this method. A feature of the mine is the No. 1 flat fault which dips 0.79 rad (45°) towards the northeast. The main characteristic of the fault is the presence of large swells of ore directly under the plane of the fault. The ground under the fault area is highly fractured and associated with massive sulfides. In the past, the ore under the fault was recovered, with difficulty, by either tight cut¬and-fill or square-set stoping. In the 1970s these meth¬ods were supplanted to a large degree by the under-cut-¬and-fill method. An advantage of the current undercut-and-fill method which uses cemented fill compared to the cut-and-fill and square-set methods is the reduction of dilution due to better control of the walls. At Falconbridge mine, it is estimated that the grade of ore produced by undercut¬and-fill is improved by approximately 10% over other methods. Where undercut-and-fill is used in very weak ground, a much greater improvement in grade can be expected. Table I shows mining production for 1974. The undercut-and-fill method was first used at Falconbridge during 1962. The first longitudinal stope was prepared for undercutting by laying down laminated beams the length of the stope and installing a lagging mat floor on top of the beams. Unconsolidated tailings fill was poured on top of the mat floor. As the cut ad¬vanced under the floor, heavy posts were placed under the laminated beams at 1.8-m (6-ft) intervals. During 1966, a radical change was made to the method when tailings fill, consolidated with portland cement, replaced the unconsolidated fill. This development eliminated the laminated beams and heavy mat floor and greatly im¬proved the stability of the stope. This system, with minor variations, is currently used at Falconbridge mine. APPLICATION The undercut-and-fill method is used to mine in¬competent ground, sills or floor pillars under mined-out levels, or a block of ore isolated between levels. It is occasionally used to advantage in sequencing produc¬tion from various mining blocks. This is done by mining a block of ore cut-and-fill method and at the same time mining the ore block directly underneath by the under¬cut-and-fill method. The undercut-and-fill mill holes at Falconbridge are either boreholes, stripped timbered raises, or steel mill holes. Boreholes and rock raises tend to slough in heavy and broken ground which increases dilution when sloughing exceeds the ore width outline and also in¬creases the difficulty of moving down to start the new cut. For example, in one installation, a 1.2-m (4-ft) diam borehole sloughed to a size of 3.7 x 5.5 m (12 x 18 ft). The undercut-and-fill method usually requires a mill hole extending from the level below the ore to the top horizon of the ore block. The customary methods of providing a mill hole are: 1) A borehole is driven from level to level through the ore block and a chute installed on the bottom level (Fig. 1). 2) An existing raise is used as a mill hole. If the raise is timbered, a steel mill hole is installed inside the timber and tailings fill poured around the steel mill hole (Fig. 1). 3) An existing steel mill hole, situated at one end of a mined-out stope, is used as the mill hole for an ad¬jacent undercut-and-fill ore block. The mill hole posi¬tion is determined when planning the mining sequence of the first stope (Fig. 2).

Jan 1, 1982