Search Documents

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive. It may be quantified as a confined or unconfined velocity. The confined velocity is the rate at which the detonation wave propagates through an explosive within a blast hole or any restrained space. The unconfined velocity emanates when an explosive is detonated in the open. However, the confined velocity is more significant as explosives are usually employed under a definite degree of confinement. This paper evaluates the increment of air deck volume and its effect on the VOD. The air gap (air deck) volume is increased stepwise from 10 to 30% of the total blast hole volume by reducing the stemming height in the collar zone. Thereafter, the VOD estimation in the 172-mm-diameter explosive column is conducted using the Dáutriche technique. It is observed that the VOD reduced with the increasing air deck volume and detonation failure is high when 30% of the blast hole volume is replaced with air deck. It is deduced that the increment of the air deck volume has an effect on the attenuation of the steady-state VOD.

By K. Soucek

Extraction of hard coal reserves, but also of mineral resources in general in the underground coal mines includes in itself many anthropogenic interventions in the earth crust. These interventions are closely associated with the solution of stability problems in the mine and with occupational safety. One of potential applications of such geo-technical interventions in rock mass is the chemical grouting technology. The chemical grouts are very suitable to affect the physical and chemical properties of rock mass. With the present development of chemical grouts, primarily based on polymers, there come into existence new composite materials during the grouting process (the so called geo-composites), which properties significantly differ from the original rock. An important factor, which affects a choice of chemical grouts and at the same time the effectiveness of grouting technology is the resulting properties of geo-composites. The properties of a coal geo-composite differ from the ones of the unmodified coal seam. On the basis of the laboratory geo-mechanical tests, the differences of properties of both material types were found. While the pure coal samples were destroyed very brittle and explosive, the geo-composite samples were making higher level of tenacity and load bearing ability after overstep of material strength. The presented paper discusses the different behaviour of these original and modified coal samples. The X-ray CT scans were used for observation and demonstration of failure evolution in these samples of pure coal and coal geo-composites after compressive loading.

Jan 1, 2006

By Charles A. Maliszewski, James M. Galvin, Gerhard Urschitz

With obvious signs of deterioration, the double track, historically registered Bergen Tunnels as part of the commuter rail system in New Jersey waited for rehabilitation for a long time. Serious water in filtration not only caused operational and safety hazards for the electrified rail line but also deteriorated and structurally compromised the tunnel lining. An innovative rehabilitation program was developed to enlarge the tunnel and to provide a new waterproofing system and final lining. For the rock excavation and support New Austrian Tunneling Method (NATM) principles were utilized, while water tightness was achieved by installing a PVC membrane waterproofing system followed by a reinforced cast-in-place final lining. Experienced on-site supervision generated additional savings during construction by streamlining support elements based on geologic conditions encountered.

Jan 1, 2003

By Armine F. Banfield

Selection of a plant site is becoming increasingly more difficult and important, mainly due to advances in technology, antipollution laws and changing economic, social and community conditions. Discussion falls naturally under three headings: economic considerations, terrain considerations and environmental considerations. Aside from acquisition of surface rights, problems having to do with terrain, or topography, usually can be dealt with by management alone. Economic considerations largely involve decision-making by management plus negotiations with government regulatory agencies acting under set rules. Environmental considerations, such as air and water pollution, townsites, housing, schools, noise abatement, appearance, surface rehabilitation and the like usually are under the control of federal, state or municipal bodies with a large degree of decision-making. Successful solution of environmental problems often requires lengthy negotiations, during which public relations by the mining company play an important part. Existing union regulations or customs may confine decision- making and the establishment of wage rates, working conditions and regulations. These usually require considerable planning and negotiation. Initial production often is delayed by formal negotiations involving environmental considerations. Surface facilities usually can be divided into two broad categories: those for concentrating ores--such as gold, silver, base metals, low-grade iron ore and potash-which should be close to the mine to reduce ore-transportation costs to a minimum, and those where the ore is shipped elsewhere for treatment, such as direct-shipping iron ores, complex high-value ores requiring specialized treatment and ores from which special products are derived for local markets. The long-term aspects of plant-site selection too often are given no or insufficient consideration because of immediate financial limitations. As a result, additional capital expenditures may be required later for relocation of townsites, roads, railroads and plants to provide additional room for extension of open-pit operations, tailings disposal, storage, or danger to foundations through underground subsidence or open-pit mining. In the past, hillside sites for concentrating plants were preferred to take advantage of gravity-feed methods The modern trend, however, is to place as much equipment as possible on approximately the same level. Some costs relating to plant sites are included in this section. They are ranges as of the year 1970, and are offered only as general guides. Such costs will vary widely with geographical location and, of course, are subject to escalation due to increases in wage rates and cost of materials. Items in the bibliography contain more detailed and comprehensive data on specific subjects. Most contain bibliographies of their own.

Jan 1, 1973

By T. Negeri, Y. Breau, M. Plante, A. Orumwense

As part of a joint project on fine particle processing, sponsored by the Consortium de Recherche Minérale (COREM), Natural Resources Canada (NRCan) and Hydro-Quebec, two flotation plant circuits were sampled to identify and quantify the causes of mineral losses within several particle size ranges. Size distributions, size-by-size assays and global chemical assays (Cu, Zn, Fe, S) were determined for the major streams. Size distributions were measured in 13 classes by sieving, cyclo sizing (-45 µm), and laser beam diffraction analysis. BILMAT, a material balance computation software package, was used to optimise the sampling, to estimate the unmeasured variables, and to assess and improve the quality of the information generated. The methodology has been extended to correct cyclo sizer data and reduce discontinuities of up to 20% at the transition from sieves to cyclo sizer. The paper describes the methodology and the main conclusions emerging from material inventory of the flow sheets.

Jan 1, 2003

By Frédéric Flament, Daniel Hodouin, Claude Bazin

A control strategy is proposed to meet the following specifications of flotation control: minimize the variations of concentrate and tails grades and recovery while limiting the amplitude of variations of the manipulated variables. The strategy consists of determining future control actions which optimize a performance criterion over a limited time horizon. The desired dynamic behaviour of the controlled flotation plant is specified using reference models. The strategy is tested on a 2-computer plant simulator working in an environment which emulates the industrial conditions.

Jan 1, 1993

By John D. Rockaway

This report and accompanying engineering geologic map describe the generalized engineering geology of St. Louis County, Missouri for use in determining the most efficient, economical, and environmentally sound program for land development and urban growth. It includes an evaluation of such factors as the physical and engineering properties of soil and bedrock, surface stability, and subsurface geologic structure. The map and text are designed primarily for property owners, engineers, architects, real estate developers, and city planners involved in land-use planning. The geologic information and engineering interpretation must be considered as a general guide and not as a substitute for a complete on site investigation prior to initiation of any land-use project. The map scale, 1:63,360 (1 inch to a mile) is too small to include the detailed information normally provided on the 7 1/2-minute quadrangle series (1:24,000). The smaller scale is most useful at regional planning levels and was chosen to present information on the more significant engineering factors of the geologic environment for county-wide planning and development. A conventional geologic map deals primarily with the distribution and variation of bedrock formations, and a pedologic map presents information on the soil or natural medium for plant growth. Basic geologic maps and pedological maps are valuable tools that can be of assistance in studying the geologic environment, however, these maps do not provide all the information required for land-use planning. The engineering geologic maps are designed to provide this data. The engineering geologic map is related to both of these basic maps but emphasizes the engineering properties of the rock formations and soils rather than their age or origin. Some of the unit boundaries shown on the county map will closely follow some geologic formation and/or pedologic boundaries; others will transgress these conventional boundaries. Earth materials, bedrock and soil, that have similar engineering characteristics have been mapped as one unit without regard to their geologic or pedologic classifications. This is to assure that geological factors are recognized, adequately interpreted, and presented for use in engineering practice.

Jan 1, 1970

By Robert A. Jankowski, George E. Niewiadomski

INTRODUCTION The utilization of longwall mining technology in the United States has steadily increased since the first longwall plow system was installed in 1952. At the errs of FY 1992, some 76 coal mines were employing longwall mining systems for coal extraction, and approximately 78 shearer and 3 plow faces are operating nationwide at any given time. Although the number of operating longwalls has remained relatively constant over the last five years, longwall production levels have increased significantly during this period. During the same timeframe, the number of continuous miner sections has decreased by 13 pct., from approximately 1438 in FY 1988 to less than 1250 in FY 1992. According to Mine Safety and Health Administration (MSHA) data, the average production of longwall sections increased from approximately 2400 tons per shift (tps) in FY 1988 to more than 3100 tps FY 1992. In fact, the average production has more than tripled since 1978, when it was only 850 tps. Approximately 25 pct. of operating longwalls are capable of producing in excess of 4000 tps. Longwall production currently accounts for nearly 36 percent of U.S. underground coal production, compared to 4 pct. in 1978. These improvements are attributed to improved longwall equipment and increased availability, larger longwall panels and automation. While longwalls are highly productive and offer other advantages, operations employing this method of mining continue to experience dust compliance problems more frequently than other mining system. Although dust levels have remained relatively unchanged over the past five years, averaging 1.6 mg/m3 and 1.9 mg/m3 based on results of operator and inspector sampling, respectively, during FY 1992, approximately 25 pct. of the operating longwalls were in noncompliance during any given bimonthly sampling cycle. Although modest gains in longwall dust control technology have been made, these have been overshadowed by significant increases in production rates. As more coal is mined, more dust is generated (Figure 1). Therefore, the increase in longwall productivity has meant that far more dust is being produced which must be controlled. [ ] In view of the current compliance record, any efforts to further increase longwall output, as has been forecasted, must be accompanied by: (1) the reduction of dust levels at existing operations through the proper installation and maintenance of suitable engineering dust controls; and (2) the advancement of dust control technology for today's and future longwalls that will enable all face personnel o work in an environment that is free of excessive levels of respirable coal mine dust. MSHA'S RESPIRABLE DUST CONTROL PROGRAM Since 1972, federal regulations have required each coal mine operator to continuously maintain the average concentration of respirable dust in the mine atmosphere during each shift in the active workings at or below 2.0 mg/m3 through the application of environmental dust control methods. The regulations provide for further reduction in the dust standard whenever the

Jan 1, 1993

By L. G. Austin

The general manner in which the liberation function must change during size reduction is described. Data from float-sink (washability) analysis of a coal is used as an illustration, and a Locking Index is defined and calculated. Ash is not distributed equally with respect to sieve size but is concentrated more in the finest sizes. On the other hand, the ash is less locked with coal in the finer sizes than in the larger sizes. Further crushing showed decreased locking in intermediate sizes, but the material in the fine sizes (produced from breakage of highly locked larger sizes) was more locked than material of the same size in the feed. Future work is also discussed.

Jan 1, 1995

By S. Chander

The fundamentals of flotation are reviewed with an objective to understand the limitations in predicting the performance of a sulfide mineral flotation system and in its scale-up from laboratory studies to plant practice. The difficulties can often be traced back to complex interactions between chemical and physical parameters and nonequilibrium effects. The physical and chemical changes that occur during the long sojourn of sulfide minerals that begins with mining, continues through crushing and grinding, and ends when they emerge from the flotation cell as a concentrate, are reviewed. The benefits of new techniques that have become available in recent years to identify and estimate the amount of surface species are discussed.

Jan 1, 1999

By M. P. Corriveau

This is the case history of how two nearby plants in Southwest Virginia solved their water clarification problems. While the solutions should not be considered applicable industry-wide, the methods used in arriving at the answers deserve consideration. When Clinchfield's Moss No. 2 Preparation Plant, the first ever built in Tiller Seam coal, was started in the fall of 1956, the clays in the raw coal soon posed a flocculation problem, Laboratory sedimentation tests were initiated; and as a result, lime was adopted as the flocculant for the clays, With lime, a pH of 11.2 was required. As the plant tonnage increased, it became evident that the amount of coal fines produced in the mining and preparation was greater than had been estimated and that the 90-foot thickener was inadequate in providing sufficient settling time to effect a clarified overflow for reuse. Testing showed that Separan 26105 (NP10)1/, when used with lime, was the most satisfactory coal flocculant available,

Jan 1, 1960

By John W. King

reserves are exploring to increase them.. Uranium exploration projects are known to be active or planned also in Guayana, Colombia, Ecuador, Peru, Chile, Bolivia, and Uruguay in South America; in the UAR, Nigeria, Angola, Mozambique, Malawi, Kenya, and Somali in Africa; and in Greece, Iran, Pakistan., Indonesia, and New Zealand. The above list, to which several might be added makes a total of at least 43 nations actively interested in exploration for nuclear raw materials. As we consider the distribution of the world's uranium resources, it is interesting to note that roughly one third of the total occurs in deposits that are economically dependant upon another product. The very large reserves of South Africa could not be produced for uranium alone, but gold has carried a sufficient part of the total cost that uranium can be recovered profitably. Approximately 40 percent of the US reserves, or 120,000 tons, are estimated as by-product recovery from porphyry copper and phosphate operations, but these reserves are not presently in production. The remaining two thirds of the world's uranium reserves have been sought, developed, and produced primarily for their uranium content. Those deposits are estimated to contain 613,000 tons of uranium oxide recoverable at less than $10 per pound. Nearly half of that uranium occurs in unmetamorphosed sandstone hosts, mostly of late Phanerozoic age--the Colorado Plateau type. About 30 percent is contained in the quartz pebble conglomerates of southern Ontario, Canada, and 20 percent is in magmatic-related deposits--veins, contact deposits, mineralized breccias, etc.

Jan 1, 1969

By Jose M. Milian, Raphael F. Matson

An intensive study was started in 1968 to determine the most economical process for winning nickel and cobalt from an extensive de- posit of complex, low grade nickel-cobalt ore (1.6% Ni, 0.10% CO) designated "the Greenvale ore." In 1974 the commercial plant at Yabulu, in Queensland, Australia, began processing the ore. In the interim, a great deal of laboratory and pilot-plant effort was applied to develop technical, process and commercial design data to demonstrate to potential financial backers and customers that a full-scale plant was feasible. The laboratory test work, pilot plant facilities and pro- gram are briefly reviewed in this paper.

Jan 1, 1979

By L. L. Newman, K. D. Ferguson

Traditional methods for mine waste management produces two waste streams and the construction of separate disposal facilities. Tailings impoundment design is usually controlled by physical stability problems. Alternatively. the waste rock offers high stability characteristics but hydraulic properties that create ideal conditions for oxidation. The problem of oxidation is significantly reduced for tailings due to a fine texture that augments water saturation. This paper introduces concepts for the co-disposal of tailings with waste rock and evaluates the physical behaviour of an integrated waste system. 'he potential benefits of co-disposal are shown for a typical mine such as Equity Silver.

Jan 1, 2000

By T. Cantwell

Techniques useful in operations, analysis are applied to the problem of planning an exploration program. The model used treats mineral exploration as a Markov process, and maximization of gain is the criteria determining the optimum program. The mathematical description of the model and the optimization are first worked out. Application of the mathematics to several simple examples is given. Finally, comparison of the data necessary to use this operations analysis with the available data shows that the method can only be a guide to planning an exploration program.

Jan 1, 1962

By Sureshan K. Moothedath

This paper provides a mechanistic representation for floc formation, growth and degradation and presents results from an experimental study of batch flocculation in which step changes were made in the impeller speed, flocculant addition, and slurry concentration. A discussion of the experimental results is included in terms of the mechanisms of floc formation and size-change.

Jan 1, 1993

By Fan Yang, Meigui Yi, Lan Xiang, Zhuoying Yang

This paper reported the calculation of the reaction heat in titanium-bearing blast furnace slag (abbreviated as TBFS)-H2SO4 system based on estimation of thermodynamic data of CaTiAl2O6 by mechanical mixture model. The thermodynamic analysis indicated that CaTiAl2O6 was more stable than the corresponding ternary oxides as CaO·TiO2, CaO·Al2O3, and Al2O3·TiO2. TBFS-H2SO4 system was highly exothermic since all of the reactions involved in the system were exothermic. For example, the increase of temperature from 25 to 200°C led to the increase of the release of the reaction heat in TBFS (100.0g)-H2SO4 system from 181.28 to 189.73kJ. Eighty-five to 90%of the reaction heat in TBFS-H2SO4 system was contributed by the reactions among CaTiAl2O6, CaTiO3, CaMgSi2O6, and H2SO4.

Feb 1, 2021

By K. J. Reid

A historical background of the development of automated material balance packages is presented including a summary of currently available packages and a description of the present work at the Mineral Resources Research Center of the University of Minnesota. A brief mathematical statement of the problem is given and solution techniques discussed. The problems and difficulties normally associated with material balances, both hand calculated and computer calculated are described. Several aspects of the available material balance packages as related to the "user/computer" interface are evaluated in detail. Elements of the material balance packages that affect the solutions are examined and the relative performance of the main packages on specialized problems presented. Finally, areas associated with automated material balances that require further work before computer packages can be widely used in industry are outlined.

Jan 1, 1982

By N. Kuyucak

Acid rock drainage (ARD) resulting from the natural oxidation of sulfide mineral wastes has become a major concern to the mining industry, both during the operational period and after mine closure. ARD is generally characterized by high acidity and high concentrations of dissolved metals and sulfates. If the generation of acid cannot be prevented or controlled, it must be treated to eliminate acidity and to reduce the concentration of heavy metals and suspended solids before release to the environment. Microorganisms play an important catalytic role in the generation of ARD. Several prevention, control and treatment technologies that are based on microbiological activities have been developed. The role of microorganisms and biotechnology in the generation of ARD and their role in the methods used for prevention, control and treatment are discussed in this paper. Recently developed passive and biological treatment processes that have been implemented at mine sites are emphasized in this paper. Benefits, limitations and design criteria for passive biological processes are also presented.

Jan 1, 2000

By A. Ardiant, C. E. F. Mumbunan, I. Irawan

As a part of mine operation’s success key, Community Development nowadays seems to be a rule of thumb. Not only is for a short term need of the company during their operation but also for the national public opinion on the presence of the mining industry to a certain region. Nanggung region which is only a 2-hour drive from Jakarta, brings the challenges to Antam’s gold mine business in the areas such as illegal miner presence, easy access to the mine area as it is very close to the community, and national political sensitivity considering its proximity to Jakarta. The company allocates about 3%of its total operational cost annually for Community Development pro-gram. The program is derived through SWOT analysis and broad involvement of all community components to assure that the allocated fund is addressed to the right place. In the year of 2002, the company has successfully established a conducive-relation with the community.

Jan 1, 2004