Search Documents

By John A. Herbst

Mathematical models of mineral processing unit operations have been developed and used for a variety of purposes. Models, defined as equations which mathematically approximate the behavior of process units, are being employed in simulators to evaluate proposed flowsheets, to investigate flowsheet modifications, to study the effect of variables on circuit behavior, to optimize the performance of circuits off-line, and to compare alternate control strategies (Mular and Herbst, 1978). Models developed for mineral processing operations may be placed in one of two general categories: phenomenological (based on mechanism) and. empirical (based on experimental data only). Dynamic models (including time as a variable) .are useful for control studies, while steady-state models (independent of time) are employed in flowsheet evaluations. Phenomenological models are potentially more flexible and accurate than empirical models. However, models constructed from theoretical knowledge are less easily developed compared to empirical expressions fitted statistically to experimental data. The latter apply only over the range of data acquired. Most often, models used in practice are the result of a combination of theoretical and empirical approaches.

Jan 1, 1979

By E. M. Cukrowska

The evaporative pan complex consists of two adjacent seasonal pans. These pans carry an exceptionally high salt (TDS) load due to over 50 years of effluent discharge via the pipeline from mines. The nutrient, heavy metal, radionuclide load in the water and sediments of the pans are very high affecting groundwater around the pans. The groundwater in the region contains TDS > 40 000 mgl-1 and sulphates > 7000 mgl-1, whereas groundwater in areas assumed to be unpolluted by mining activities have TDS < 500 mgl-1 and sulphates < 200 mgl-1. The extent of continuity between the pans and the groundwater is unknown, although there appears to be seepage of contaminated groundwater into the river system.

Jan 1, 2006

Thermal pretreatment can significantly improve industrial comminution operations by reducing energy requirements and increasing mineral liberation. The effect of pretreatment using conventional and dielectric heating followed by quenching on the fracture properties of a number single and multiphase brittle materials has been investigated. The reduction in the impact fracture energies and particle strengths with and without pretreatment has been measured in precise single-particle experiments using the Ultrafast Load Cell. Variations in the fragmentation pattern caused by different pretreatments were assessed by measurements of the progeny size distributions. The differences in the effect of thermal treatment on single and multiphase materials are discussed based on the experimental results.

Jan 1, 1995

By Jean E. Kiel, Rob Dorey, Dirk J. A. van Zyl

1.1 INTRODUCTION This chapter seeks to provide an overview of important factors involved in the implementation of heap leach technology as a vehicle for gold extraction from its ores. Toward this end, brief discussions of the various elements important to this process are presented here. Topics covered in this chapter include a brief history of the process; basic chemical reactions responsible for the process ; characteristics of ores amenable to heap leaching; location of the greatest concentration of heap leach projects in the U.S.; heap leach components, methods, regulatory/permitting considerations; and economic considerations. Most of these subjects are treated at much greater length in subsequent chapters. Thus, this chapter serves as a summary for those which follow, in addition to providing the reader with a feeling for those topics which may be of most immediate interest. 1.1.1 History of the Process Modern Day Precious metal heap leaching technology has developed over the past decade, although the principles of heap leaching per se, as well as those of gold extraction through cyanidation have a long history (see discussion below). However, it is in the past 10 years that heap leaching has developed into an efficient method of treating oxidized gold and silver ores. It has proven to be both an efficient way to extract precious metals from small, shallow deposits, as well as an attractive way to treat large, low- grade, disseminated deposits. Heap leaching has several advantages compared to conventional milling (i .e., crushing, grinding, and agitation leaching). In general, these advantages include simplicity, lower capital and operating costs, shorter start-up times, and less intensive environmental regulatory concerns. A possible disadvantage of currently existing heap leach technology is a potentially lower percentage of metal extraction being obtained from the ore than would be the case with conventional milling (Potter, 1981; Hiskey, 1985; and Thorstad, 1987) The actual principle of heap leaching has a long history as inferred previously. For example, mines in Hungary recycled copper-bearing solutions through waste heaps in the mid-sixteenth century (Hiskey, 1985), and Spanish miners percolated acid solutions through large heaps of oxide copper ore on the banks of the Rio Tinto around 1752. By 1900, leaching operations were employing such techniques as leach/rest cycles to maximize copper recovery (Taylor and Whelan, 1942; Thorstad, 1987). Copper dump leaching is currently

Jan 1, 1988

By Jed H. Mosgrove

One of the most interesting of all the subjects required of persons studying the different facets of coal mining is coal mine gases. Some mine gases have been a real problem since the very beginning of underground mining, and in the early days there was insufficient knowledge to cope with them. The history of mining shows that until about the last 50 years, much work was done primarily by the hand methods which are primitive by today&apos;s standards. Miners had to contend with gases without the aid of enclosed lighting, permissible mine machinery, sophisticated testing devices, and high-pressure ventilating fans. In early days the miners were not educated about the different mine gases nor did they have the technical equipment to determine the actual composition of the deadly atmospheres they encountered. They simply applied a descriptive term to each gas or mixture of gases depending on its effect on a person or the surrounding atmosphere. The gases or mixtures of gases were then referred to as "damps," a term which was probably derived from the German word "dampf," meaning vapors or gases. The more common damps encountered were : Blackdamp A condition of the atmosphere in which a miner&apos;s light would be extinguished and in which breathing would be difficult, sometimes even resulting in suffocation. An atmosphere deficient in oxygen which could contain a combination of any of the mine gases Firedamp A flammable mixture of methane and air which would either burn or explode when ignited. White Damp A mixture of gases containing carbon monoxide, most often found in mines during fires or after explosions.

Jan 1, 1981

By Samuel S. Adams

The Grants uranium region of northwest New Mexico is the largest uranium district in the United States (approximately 50% of U.S. production plus reserves) and one of the largest In the world, with approximately 900 million pounds U308 production plus reserves. Deposits of the region are unusual among sandstone deposits for their high content of epigenetic carbonaceous material, generally interpreted but not proved to be of humic origin--that is, co-extensive with uranium in the primary deposits. Virtually all production in the region has been from the Jackpile Sandstone and Westwater Canyon Member of the Jurassic Morrison Formation. The tabular uranium deposits contain, in addition to humate and uranium, significant authigenic phyllosilicates, quartz overgrowths, humate-replaced detrital silicates, and a trace-metal assemblage typical of other sandstone uranium deposit types. Surrounding the deposits in the two sandstone units of the Morrison Formation is an alteration zone within which iron leaching has altered detrital ilmenite-magnetite to residual masses of titanium oxides. Feldspar alteration is locally present within this zone, below deposits in the Jackpile Sandstone, and above those in the Westwater Canyon Member. The feldspar alteration increases in inten¬sity toward the Brushy Basin Member which separates the two sandstone units, ranging from partial replacement to replacement and dissolution of plagioclase and sanidine. Spatial relations among the epigenetic humate, authigenic silicates, and the broad alteration zones that extend from the Brushy Basin Member to and including the uranium deposits suggest that (a) the organic material was involved in the unusual silicate alteration, transport, and authigenesis, and (b) that the humates originated in shales of the Brushy Basin Member. Stratigraphic relations among the Brushy Basin Member and the overlying Jackpile Sandstone and underlying Westwater Canyon Member suggest [in turn] that there was continuous, interfingering deposition controlled in part by contemporaneous basement subsidence along northwest- and northeast-trending zones. Following minor erosion of upper Jackpile Sandstone and deposition of basal organic-rich Cretaceous sediments, the silicates of the Jackpile Sandstone were once again altered by organic-bearing fluids, this time permeating down from Cretaceous sediments and partly obliterated ore-stage alteration.

Jan 1, 2013

By Byron C. Hardinge, Michael Sokaski, Paul F. Sands, W. Loring III Mc Morris, David J. Akers

INTRODUCTION In the early days of coarse-coal cleaning by the dense-medium process in Europe, loess was one of the materials used for medium solids. Newly developed cyclones were used to reclaim and thicken the loess suspension. On occasion, when the cyclone thickener at the Maurits mine in the Netherlands plugged, the overflow was found to be filled with clean coal free of impurity. From this observation stemmed the concept of the cyclone as a cleaning device. Development took place during World War II in the laboratory of the Dutch State Mines under the direction of M. G. Driessen. A 15-tph (13.6 t/h) pilot plant was in operation in the laboratory by 1945, when, in September, Driessen made the first public disclosure of the process in a paper presented to the Institute of Fuel in London.51 In April 1945, operation of this pilot plant was observed by H. F. Yancey, who was so impressed with the potential of the cyclone process that, on his return to the United States, a research program on the cyclone was immediately started by the US Bureau of Mines (USBM). This work led to an AIME paper in 1946 in which the first details of cyclone operation on American coals were made available.52 Commercial adoption of the cyclone proceeded in Europe, initially in the Netherlands, Germany, and France. In the United States, where coal is less costly and most of the coals are easy to clean and respond well to simpler cleaning processes, the first cyclone plant was not built until 1961.53 THEORY Before discussing the theory of a dense-medium cyclone, a brief description may be helpful to some readers who are not familiar with its basic operation. In a typical dense-medium cyclone, illustrated in Fig.7-51 a mixture of medium and raw coal enters tangentially near the top of the cylindrical section, thus forming a strong vortical flow. The refuse moves along the wall of the cyclone and is discharged through the underflow orifice. The washed coal moves toward the longitudinal axis of the cyclone and passes through the overflow orifice, or vortex finder, to the overflow chamber. Washed coal is discharged from this chamber, usually through a tangential outlet.

Jan 1, 1991

By Charles F. Stack

The A. P. Green Refractories Co. operates clay mines in ten states. Eight of these states have reclamation laws with which we have to comply and indications are that the U. S. Congress will pass a federal surface mining reclamation act in the near future. These regulations, in addition to the value of land in most areas, dictate that mining and reclamation be considered as a single operation. In many instances the land may be more valuable after properly planned mining and reclamation than before. Refractory clay, commonly called "fire clay" is defined as a siliceous clay rich in hydrous aluminum silicates, capable of withstanding high temperatures. It is deficient in iron, calcium, and alkalies and approaches kaolin on composition. Refractory clay is much more limited in occurrence and usage than common clay or shale. During 1971, common clays and shales were mined in 47 states with a total production of 45 million tons. Fire clay production was reported in 22 states with a total production of only slightly over 3 million tons.(1) Many of these producing areas are extremely limited in extent and production. Several are contained within a one or two county area. This reflects the unique geological conditions required for the formation or development of fire clay. The major fire clay producing areas in the United States are shown in Figure 1.

Jan 1, 1974

By A. K. Kelly

Potash was first discovered in Saskatchewan in 1943 but its continuous extraction did not begin until 1962. In the years since then, potash has played an important role in the economic and political life of the province. And, as is well-known, the most eventful time in the life of the industry occurred in 1975 when the Government of Saskatchewan decided to become a major participant in potash production. To understand that decision, however, requires an understanding of the economic development of Saskatchewan and of relations between the industry and the government prior to 1975. This year, Saskatchewan celebrates its 75th year as a province. For most of those years, we have been an agrarian economy and society, dependent on exports of cereal grains, mostly wheat, for a livelihood. Even today, agriculture accounts for about 25% of the province&apos;s Gross Domestic Product (Economic Review, 1979, p. 7) and difficulties in agriculture spread rapidly to the rest of the provincial economy. The difficulties and risks that go hand in hand with being a "one crop" economy were known as long ago as 1920 but were not fully appreciated until the combination of depression and drought in the 1930&apos;s turned the prairie grain- belt into a dustbowl. Some idea of the severity of the depression is revealed by the following data: in 1928, Saskatchewan produced 321 million bushels of wheat. By 1931, the total fell to 132 million bushels and, in 1937, to a mere 37 million bushels. The value of agricultural products sold off farms fell from $273,000,000 in 1928 to a meagre $51,000,000 in 1937. The impact of such a fall of agricultural incomes was catastrophic since about 70% of the population of some 921,000 persons lived in rural, agriculture-dependent areas (Britnel.1, 1939, p. 14).

Jan 1, 1980

By J. R. Gump

The term "rare earths" is used to designate a group of elements, Numbers 57-71 which are closely related chemically. They were called "earths" because their oxides resemble those of the alkaline earths, and the designation "rare" was originally applied because of their scarcity. Now many of these elements are known to exist in considerable quantities, and the term "Lanthanide" is applied to this group of elements, because of their similarities to lanthanum, the first element in the group. Many authorities insist on including yttrium, element Number 39, because of its extremely close association with the members of the group in nature and because of its similarity in chemical properties. It has been estimated that the combined rare earth group makes up about five-thousandth. of one percent of the Earth&apos;s crust, a higher percent than the common elements, lead, tin, zinc, arsenic, mercury, silver and gold. Cerium is by far the most abundant member comprising about half of the total amount. Yttrium, neodymium, and lanthanum are next in order; samarium, gadolinium, praseodymium, dysprosium, erbium, holmium, and ytterbium are increasingly scarce; while the elements lutetium, thulium, terbium, and europium are extremely rare. The rare earths as a group are metals, usually trivalent, forming basic oxides, and insoluble oxalates in dilute mineral acids. Their fluorides are also difficultly soluble; hence the rare earths or lanthanides may be separated, in general, from other elements by adding oxalic or hydrofluoric acid to a dilute mineral acid solution containing them. The most striking fact which characterizes these elements is the remarkable .similarity in both the physical and chemical properties of their compounds. Their main differences are in the solubilities of their salts and the basicity of their oxides, which vary between that of the alkaline earths and that of aluminum.

Jan 1, 1960

By E. R. Hendrickson

About 1/3 of the world&apos;s supply of phosphate rock is produced in a relatively small area of the Florida peninsula east of Tampa. Until this past year, a circle with a radius of about 25 miles and centered on Bartow would encompass the major producing areas. During the past year producing areas have opened in North Florida which promise to vie with the Polk-Hillsborough County area in terms of proven reserves. In addition, new phosphate production is planned for counties to the south and west of the present fields. From the existing production areas, however, more than 19 million long tons of phosphate were mined in 1965. As mining engineers most of you probably are familiar with the methods of mining and beneficiating the pebble phosphate rock. You thus recognize that, although some water quality problems may arise from these processes, there is no potential air pollution problem. To make an economically useful product, however, further processing must take place. It is from this additional processing that potentially damaging materials may be discharged to the atmosphere.

Jan 1, 1966

By Yu. A. Polozov, V. A. Lagunov, O. Yu. Lushinkova, Yu. I. Svirskiy, Eh. Ya. Kipko, Roy A. Williams

4.1 THE GENERAL COMPOSITION AND PROPERTIES OF CLAY-BASED GROUTS Clay-based grouts are visco-plastic systems; they are made by adding structure-forming reagents to a clay mineral mortar. Small amounts of cement and various chemical ad¬ditives constitute the reagents. If necessary, fillers also are added. The distinguishing feature of clay-based grouts is that throughout their entire stabilization period they do not form a crystallized structure as does cement grout. The structure of stabilized clay-based grouts does not deteriorate during minor rock movement or upon the initiation of blast¬ing during the construction of a shaft or a drift. Because they can possess good rheological properties during the ini¬tial structure-forming period relative to cement grouts, clay¬based grouts are not easily eroded from large fractures and karstic cavities by flowing ground water. In addition, their finely dispersed clay particles facilitate a greater fracture penetration capacity, especially in dual porosity rocks. Numerous investigations of the structural-mechanical and rheological properties of clay-based grouts by STG have demonstrated that the most effective grouts for pre¬venting the inflow of ground water into underground work¬ings are grouts that have a cement content of 8 to 10% (90 to 120 kg/m3) of the clay grout by mass. The grout should have a density of 1.18 to 1.30 T/m3. Various additional substances and chemicals can be added as additional fillers and structure-forming reagents. In pure ground water at temperatures above freezing, sodium silicate in the amount of 0.8 to 1 % by mass normally is the only structure-forming reagent that is necessary if the proper clay is selected and if it is available. The production process for making clay-based grout is divided into two stages: 1) the production of an initial clay mortar with specified properties and 2) the production of a clay-cement additive grout mixture using the initial grout along with the structure-forming reagents, including the ce¬ment. The properties of clay-based grouts depend on the phys¬ical-mechanical properties of the initial clay mineral, the properties of the cement and the properties of the chemical reagents that are added. 4.1.1 TECHNOLOGICAL PROPERTIES OF CLAY-BASED GROUTS The dynamic shear stress&apos; To, the viscosity 11, the static shear stress2 0, the maximum shear stress of the structured that the rheological and structural-mechanical prop¬erties of clay-based grouts must fall within the following limits: the dynamic shear stress To = 50 to 200 Pa; the viscosity -9 = 0.02 to 0.07 Pa sec; the static shear stress 0 = 150 to 600 Pa; the plasticity strength Pm of the structure one minute after preparation (according to P.A. Rebinder&apos;s method) equals 150 to 500 Pa. The plasticity strength 10 days after preparation is ? 0.15 MPa. The general relationship of the change in the structural strength of clay-based grouts relative to stabilization time is shown in Fig. 32. The figure shows that the structure-form¬ing process for clay-based grouts is characterized by three stages. These stages correspond to the time periods required for conducting the principal operations during the injection of the grout into a fractured aquifer as described below. Stage I, corresponding to the time period T1, reflects the small development of structural strength during early stabi¬lization. During this time, the structural strength must not preclude the capability to pump the grout. The time Tl must correspond to the length of pumping time from the moment water is shut off and mixing occurs until the pump stops forcing the grout through the manifold block and pipeline into the fractured rock as described subsequently herein. Stage II, corresponding to the time interval T2, reflects a sharp but controllable increase in the structural strength of the grout. The length of time period T2 is controlled by the addition of appropriate reagents. Stage III produces the final value of the structural strength. This final strength is used to design the dimensions of the isolation curtain. Consequently, the development of grouts is guided by two principal criteria: 1) the grout must develop the highest possible structural-mechanical properties and 2) it must be able to be pumped by a piston pump prior to final stabili¬zation. Successful grouting depends to a large extent on the correct design of a grout for each specific case. It is impor-

Jan 1, 1993

By J. R. Dillon

Today more than ever, there is an increased demand for higher plant production capacities and efficiencies to offset the increasing costs for labor and materials. Plants involved in processing large volumes of bulk materials are particularly interested in more efficient material handling systems to (1) reduce labor and maintenance costs, (2) improve blending of non-uniform raw material feed to processing facilities, (3) improve blending of finished bulk materials from storage. DragScraper systems are being used effectively for handling a variety of bulk materials in both indoor and outdoor storage. Materials being handled include ores, chemicals, coke, clay, and stone, to name a few. Handling capacities these machines can provide vary from a few tons to over 1500 tons per hour. The basic components of a DragScraper machine consist of a bottomless Crescent scraper, a two or three-drum DragScraper hoist assembly including gas, diesel, or electric power unit, operating cables, guide blocks, and either fixed or mobile head and tail structures. They are presently available in sizes through 15 cubic yards, for operating spans up to 1000 feet.

Jan 1, 1969

By Richard H. Sailors

Data from full scale marked ball tests are used to demonstrate the effects of abrasion, corrosion, and impact on overall wear rate. The predominate wear mechanism need be identified before the optimum alloy can be chosen for the grinding media. Use of high chromium grinding media often results in increased mill efficiency due to shape retention. Thus, a benefit from energy savings can result as well as a reduction in wear rate. Converting from steel to east high chromium grinding media requires close association and cooperation between producer and consumer in order to properly conduct these studies.

Jan 1, 1990

By Hans G. Kok

At this time in the history of engineering and construction, cost indexes give weekly evidence of the sharply rising costs of labor and materials. Paralleling the rise in construction costs are the costs of plant maintenance. Automation of the modern industrial plant has permitted a substantial reduction in the total number of employees required for plant operation. Of this reduced total, however, up to one-half of the employees may be engaged in plant maintenance. Management&apos;s decision to risk investment capital for a pro- posed plant or improvement is increasingly dependent upon the engineer&apos;s ingenuity in designing plant systems and structures which will require a minimum of materials and labor for manufacture, installation, and operation and which will be maintenance-free to a maximum degree. This paper concerns itself with the structural elements of bulk material handling systems in which the foregoing factors influenced the design to a considerable extent.

Jan 1, 1969

By S. A. Bortz

IIT Research Institute has initiated several multi-sponsored research programs. In this paper the methods for developing four of these programs are discussed. In general, a broad area of investigation must be proposed to interest a spectrum of different industries. The work must not touch upon proprietary data and will probably involve a number of scientific disciplines. Thus, the problem to be solved will attract sponsors who need to know more about the area under study but do not wish, as a single company, to commit the resources required to obtain the necessary know-how for their needs. The paper draws on the background of four IITRI multi-sponsored projects: Size Reduction, a study of grinding of material to reduce their particle size; Melt-Formed Ceramics Research, a method of producing dense, polycrystalline ceramics using glass forming methods; Binders in Ceramic Processing, which addresses the problems associated with the use of organic aids for ceramic processing; and a Study in Air Pollution Technology, a program to review and assess pollution control equipment for current and future applications.

Jan 1, 1984

By A. LaPlante, A. Cauchon

This gravity circuit at Les Mines Camchib Inc. consists of two pinched sluices to bleed a feed to one of two 76 cm (30") Knelson concentrator. The Knelson concentrate is upgraded to smeltable grade with a smaller Knelson (18130 cm) and a riffleless table. Their tails are column cyanided and washed prior to recycle to the grinding circuit. This paper details size- by-size circuit performance. The Knelsons recover around 90% of free gold (as determined by Mozley Laboratory Separator), even below 37 pm. The sluices are ineffective, with upgrading ratios around 2, but approaching unity in the fine sizes. Much of the effectiveness of the circuit lies in the high gold circulating loads in the grinding circuit, which partly atone for the poor sluice performance, and the ability of the Knelsons to recover free gold. Secondary upgrading recovers slightly above 99% of the primary concentrate gold, 90% of it in a 65% Au concentrate and the balance in a heavily loaded (10 to 20 oz/st) pregnant solution, generated by intensive column cyanidation.

Jan 1, 1990

By M. A. Sochocky

Rod mills were developed, as a logical substitute for the rolls crusher when larger tonnages had to be handled, on a continuous basis. Today, with even larger tonnages to process, the trend is to install larger equipment, automate the plant and develop the highest availability possible, in order to cut costs. The rod mills, because of design limitations in size and speed 1&apos;2, are not able to meet these new requirements. The autogenous mill was a timely development and serves as an excellent alternative for ores that are suitable to this type of grinding. When ores are not amenable to autogenous grinding, selection of a flowsheet is dictated by liberation characteristics and unit operations to be used for mineral recovery.. The following alternatives are available: (a) Multiple rod mills, capable of drawing no more than 2000 HP each, followed by ball mills. (b) Gyradisc crusher followed by two stages of ball mill grinding.3 (c) Tertiary crushing followed by closed circuit single stage ball mills grinding to approximately -100 mesh, as in the copper industry. (d) Tertiary&apos; crushing followed by two-stage, ball milling. Each stage will operate in closed circuit with either screens or cyclones. It is this last alternative, particularly as it

Jan 1, 1972

By Gerald H. Luttrell, Jaisen N. Kohmuench, Michael J. Mankosa

A new separator, known as the Hydrofloat cell, has been developed to overcome limitations of traditional flotation cells in recovering coarse particles. In this process, small air bubbles are introduced into a hindered "teeter" bed of fluidized solids to create light bubble-particle aggregates that can be separated based on differences in density. Laboratory tests conducted with coarse phosphate feeds indicate that the Hydrofloat cell is capable of increasing BPL recoveries by nearly 20% over conventional flotation methods. Based on these encouraging results, a pilot-scale Hydrofloat cell was fabricated and installed at a central Florida phosphate plant. Test data collected using the pilot-scale unit suggest that the BPL recovery of the plus 35 mesh plant feed can be increased by more than 40% through the application of this new technology. This improvement is particularly beneficial due to the very high grade (-73% BPL) of the plus 16 mesh particles in the Hydrofloat concentrate. This article describes the theoretical basis for the development of the Hydrofloat cell and provides an overview of recent laboratory and pilot-scale test results.

Jan 1, 1999

By S. McMurray

INTRODUCTION Towards the end of the 1890s the attention of a prospector by the name of Thomas Cullinan was drawn to the occurrence of alluvial diamonds east of Pretoria. Persistent prospecting work by Cullinan led to the loca¬tion of the source of these diamonds-a kimberlite pipe on the Elandsfontein farm. Cullinan eventually acquired the property in 1902, and during an extensive evaluation program outlined the largest diamondiferous pipe in South Africa on which the Premier mine was established. Worldwide attention was drawn to this mine in 1905 when the Cullinan diamond, which weighed 3106 carats and is by far the largest gem diamond ever discovered, was recovered. Premier mine operated with varying success until 1932 when the worldwide depression forced it to close. In 1945 the mine was reopened and since then has been a major producer of gem and industrial diamonds. During the early 1950s exploratory drilling revealed that below the 370-m level the pipe had been completely cut off by a younger gabbro sill. This sill has created major mining and metallurgical problems but the existence of vast reserves of high grade ore below it justi¬fied the establishment of virtually a new mine below the sill. Detailed planning of below-the-sill mining is nearing completion and the development of the first mining block (the L1 block) is well advanced. A full discus¬sion of this block follows. GEOLOGY OF PREMIER MINE Pipe Morphology and Country-Rock Geology As can be seen in Fig. 1, Premier mine is an elon¬gated oval shape with a long axis of 900 m on the surface and a short axis of 450 m. The pipe has a surface area of 32 hectares which decreases progres¬sively with increasing depth, so that 500 m below the surface the area is reduced to 22 hectares. The contact between the kimberlite and the surrounding country rock is sharp, with an average angle of dip of 1.48 rad (85°). From the surface down to approximately 350 m, the country rock is a felsite which grades downwards into a norite. In general both rock types are hard and massive, the felsite in particular being poorly jointed. This characteristic combined with other factors results in an extremely stable open pit, and near-vertical side¬walls are currently being maintained. The norite in general is competent but is heavily jointed in some areas resulting in very blocky ground which creates localized tunnel support problems. In the southeastern area below the sill a zone of highly altered and very unstable norite, which has also created localized sup¬port and development difficulties, lies adjacent to the pipe contact. Kimberlite Geology The Premier pipe is a complex multiple intrusion which contains in the region of 15 separate types of kimberlite, most of which are volumetrically insignifi¬cant. On a simplified basis three major types can be identified which correspond to three separate phases of intrusion. They are: Brown Kimberlite: This represents the first phase of intrusion and now occupies the eastern part of the pipe. In plan the brown kimberlite has a crescentric shape resulting from the intrusive relationship with the younger gray kimberlite which lies to the west. The brown kimberlite increases in relative area with increas¬ing depth which is a favorable factor for future mining operations since this kimberlite is the richest area of the mine, having an average grade of 70 carats/ 100 t. Below the sill this rock disintegrates extremely rapidly when exposed to air or water, to form a fine gravel-like material. This characteristic is due to a high montmorilonite clay content. As is common with clay minerals of this type, water can be absorbed into the crystal lattice with a resultant increase in volume which causes the physical decomposition of the rock. The presence of this decomposing kimberlite was a major factor governing the choice of a mining method, as well as development and tunnel support techniques. Gray Kimberlite: This is the most abundant type and represents the second major phase of intrusion. The diamond content is variable depending on the amount of waste rock dilution, and in general the rock is stable and non-decomposing. At the time of formation of Premier, the surface rock type was Waterberg quartzite, a rock formation which has subsequently been removed from this area by erosion. The explosive extrusion of the gray kimberlite caused extensive brecciation of this rock and while the kimberlite was in a mobile state huge masses of quartz¬ite, amounting to tens of millions of tons, slumped into the pipe. This quartzite became concentrated in the central area of the mine and has been a major mining problem throughout the history of Premier since, due to the irregular distribution of the quartzite, effective selective mining has never been possible. The quartzite is therefore extracted with the ore and has a significant dilution effect on the overall grade. Black Kimberlite: In the western part of the pipe a circular, pluglike body of kimberlite is intruded into the gray kimberlite. This plug consists mainly of a hard, dark-colored rock known as black kimberlite, but also contains a number of minor kimberlite variet.ies as well as nonkimberlite carbonate dikes. The Gabbro Sill The sill averages 75 m in thickness and within the confines of the pipe consists of 52 million t of rock. On average the major dip is 0.34 rad (20°) to the northeast which is across the short axis of the pipe, the range of dip being from near horizontal up to 0.52 rad (30°). Due to the pronounced dip, the sill is encount¬ered over a vertical distance of 175 m with the highest upper contacts on the 355-m horizon and the lowest bottom contact on the 530-m horizon.

Jan 1, 1982