Search Documents

By A. M. Alfantazi, R. R. Moskalyk

Over the years, improvements have been made in the recovery of nonferrous metals, including improvements in the areas of mineral processing, pyrometallurgy and hydrometallurgy to extract cobalt as a byproduct from host minerals containing mainly nickel, copper and associated precious metals. At present, the technological emphasis is on solvent extraction coupled with electrowinning (SX-EW) for lateritic sources of supply within the Southern Hemisphere, such as in Australia and New Caledonia. Although sulfide-bearing ores, such as those found in Canada and Russia, will serve as a viable long-term source for cobalt, a ubiquitous metal, the future trend is anticipated to be in the implementation of compact and efficient SX-EW facilities that apply state-of-the -art innovation with environmental compliance This paper serves to collate the known practices for the recovery of market-grade cobalt by means of electrowinning from either an aqueous sulfate medium or chloride medium after upstream leaching, solvent-extraction and solution-purification procedures. For completeness, other commercial production techniques for the recovery of cobalt as a sulfide or oxide product are included in the summary of current cobalt processing practices.

Jan 1, 2000

By E. J. Beckman, R. M. Enick, C. Shi

A novel liquid-liquid separation for the recovery of free or liberated gold from mixtures of fine particles was evaluated. Two inexpensive and environmentally benign fluids were selected for the study, water and carbon dioxide. The separation, which is conducted at 295 K and at the vapor pressure of carbon dioxide (6.0 MPa), is based on differences in wettability between the precious metals and other minerals. Contact-angle results indicated that, in the presence of water and liquid CO2, gold is slightly hydrophobic. The addition of CO2-soluble fluoroalkyl thiols or f uoroetherthiols increased the hydrophobicity of gold exposed to water and CO2 to a greater extent than alkylthiols. Minerals, including quartz, pyrite and magnetite, were hydrophilic. During the separation, an aqueous slurry of fine mineral and gold particles was mixed with liquid carbon dioxide. Pure gold particles (-325 mesh) were found to agglomerate at the H2O-CO2 interface. The minerals tended to remain in the aqueous phase. Despite these promising preliminary results, very poor gold recoveries were obtained when applying the procedure to an Australian gravity concentrate. This was attributed to the native gold particles in the concentrate being either too large, agglomerated in slimes or coated with minerals. Although this particular application was unsuccessful, this water-CO2 biphase technique may be applicable for other separations that require the removal of very fine, hydrophobic particles from an aqueous slurry.

Jan 1, 2000

By I. K. Kapageridis

Digital photography combined with three dimensional models of topography, mining operations and restoration plans can lead to extremely realistic images and animations of the current and future states of a mine or quarry. The amount of work and the time required for the successful modeling of a mine and its restoration plan are surprisingly low nowadays. All this means that the visual impact of mining and quarrying operations can be easily assessed using common computer hardware and some dedicated software packages. LAVA Mining and Quarrying SA is a company committed to strive continuously for the highest possible environment protection at the company?s quarries. The pozzolanic rock quarry located at Xylokeratia is one of the company?s quarries on the island of Milos and the subject of the study presented in this paper. A thorough restoration plan of the Xylokeratia quarry is being completed by the company. For its purposes, a complete visual impact assessment study was performed at the Department of Geotechnology and Environmental Engineering of the Technological Education Institute of Western Macedonia. The procedures used in this study and the produced visual results are presented in this paper.

Jan 1, 2006

By Frank L. Peterson

This paper deals with problems of groundwater development in an insular circum-Pacific environment, and is not oriented as such to mining and mineral development. Nonetheless, because a reliable water supply is necessary for most mining and related support activities, and since water supplies are limited in many insular parts of the Pacific Basin, groundwater development is a subject which must be frequently addressed. Because many in the audience may be already familiar with groundwater development for continental environments, I have chosen to deal with groundwater occurrence and development problems which for the most part are unique to insular environments. In such environments, the local geology plays a critical role in determining groundwater occurrence and its suitability for development. The three examples discussed in this paper-Hawaii, Guam, and the Marshall Islands-were selected because they illustrate groundwater occurrence in a wide range of geologic conditions. For example, the Hawaiian aquifers consist primarily of basaltic lavas, while Guam is made up of andesitic lavas and coral reef limestones, and the Marshall Islands are coral atoll deposits. Despite differences in aquifer size and rock types, the principal mode of groundwater occurrence at the three sites is similar; thus, development strategies are also similar. Figure 1 shows the location of the three sites.

Jan 1, 1982

By G. H. Matthes

Many mines, in particular coal mines, use inclines or slopes as an access to seam or seamlike deposits which outcrop at or close to the surface. In general, from the surface or from a certain depth, inclines or slopes follow the dip of the deposit with length up to 30,000 feet and by that going under an overburden cover of several thousand feet. The common outbye transport system for mine products is the conveyor. Material and men to be transported down into the mine are handled by rope driven systems when the angle of inclination exceeds the employment of locomotive traction. The transport volume can be sizeable and reach 200 to 300 tons of material and 500 men to be handled daily in a medium size coal mine with a production of 10,000 tons ROM.

Jan 1, 1986

By Ehsan Alavi Gharahbagh

Tool and cutterhead wear is a crucial issue in soft ground tunneling, especially because tool inspection, maintenance, and replacement are done under difficult conditions, and often under pressurized faces or under ?hyperbaric interventions?. Overall, tool inspection and changing is a time consuming and costly step, which needs to be quantified and the related costs accounted for in any construction contract for scheduling and costing of the tunnels at design stage or bid preparation. However, lack of a universally accepted index or measure for soil abrasivity in the geotechnical reports has made it difficult, if not impossible, to define cutter wear for this purpose. Soil abrasion and its impact on cutting tools for tunneling machines under dry or wet conditions have recently been under spot light due to construction claims in several of the recent tunneling projects. The objective of this paper is to examine soil?s physical, mechanical and tribological properties related to the interface of the soil and excavation tools and discuss ways to measure soil abrasivity in a quantitative and repeatable manner. The paper will discuss the efforts that are underway to develop a new soil abrasivity index and the fabrication of a new testing device for this purpose.

Jan 1, 2010

By Ben H. Daud

The systems optimization approach to mine planning has led to the adoption of a number of mathematical and computer models for short, medium and long range planning of mining operations. In the realm of open pit mine planning, the most common uses of such an approach have been in the areas of optimal pit design and planning of materials handling operations. Since a truck-shovel combination is the most widely used method of materials handling in open pit mines, a number of models have been presented in the past to analyze and optimize such systems. Broadly, these models can be divided into two categories. The simulation model, which is primarily used as an aid in analyzing the performance of either an operating or a proposed haulage system under the influence of externally alterable parameters, and the linear or integer model which is used as a tool for short or medium term optimization of the system under the operating constraints. In the first part of this paper, a brief discussion is presented of the linear/integer optimization models presented in the past, and in the second part a new model is described which is actually a combination of the simulation and the integer programming models. In its bare essentials, the model consists of an integer optimization algorithm, but the constraints are regularly and dynamically updated by incorporating the conclusions drawn from a stochastic simulation model of the mine haulage system. Since the successive optimization is performed by the mine operator who manipulates the constraints to guide the model towards the optimum, the mystical black box approach is minimized and should help in adoption of the model by the mine personnel. Also, by combining the stochastic simulation model and the deterministic integer model, some of the advantages of each are acquired.

Jan 1, 1976

By Robin P. Gardner

The mechanistic or phenomenological approach to ball milling involving the, concepts of particulate selection and breakage functions with particle population balance models has been well established over the past decade (c.f., the review articles by Austin (1) Herbst and Mika, (2) and Snow (3)). Initial efforts to apply this approach concentrated on batch milling, but since most milling in industrial practice is continuous, much recent research has been directed to extending this approach to continuous milling. The primary difference between batch and continuous milling processes is the relative importance of material mixing and transport in the mill in the latter case. Much analytical (4-8) and some experimental (9-15) work on the effect of mill mixing and transport on milling has been recently reported. Much of the analytical work has naturally centered around extension of the well-developed concepts that have been applied to chemical reactors, (16-18) Fortunately, it has been found(1) that most milling processes are analogous to first-order chemical reactions so that the combined effects of material transport and reaction (breakage) can be handled by the relatively simple segregated flow concepts. (8)

Jan 1, 1973

By Scott A. Norby

Kennecott's Ray Mines Division (RMD) is located in central Arizona. The pit and silicate plants are located at Ray while the 27,500 tpd concentrating facilities are located at Hayden, approximately 20 miles away from the pit. Ore is delivered in 100 ton railroad cars, 60 cars per train via the Copper Basin Railroad. The side discharge cars are dumped into a 6,000 ton trackhopper. There are 6 Nico feeders, two per belt. Three 48" belts transport the -8" ore to three 7' standard (secondary) Nordberg crushers. Each crusher is preceded by a 6' x 12' Tyler double deck screen. The secondary crushers are open circuit. The -1/21t material from the screens is transported directly to the fine ore bin at the mill. The discharge from the crushers and the intermediate product -2 1/411 x +1/2" is conveyed to a surge bin. The tertiary crusher feeder belts discharge onto five 61 x 161 Tyler double deck screens, each followed by a 7' shorthead (tertiary) Nordberg crusher in closed circuit. The -1/2" product joins the -1/2" ore from the secondary crushers and both are conveyed along a 42", 4,230 foot long belt to the fine ore bin that feeds the grinding circuits. When hard ore is experienced at the concentrator the daily throughput decreases by up to 10%. This coupled with the fact that the ore is generally becoming harder with mine depth provided the incentive to improve the performance at the crushing plant.

Jan 1, 1986

By M. J. Howes, C. A. Nixon

INTRODUCTION A safe heat stress control strategy for an underground mine has three elements: Application of an environmental measure which reflects physiological strain with sufficient accuracy for the range of conditions encountered underground. Acceptance of a functional relationship between the environ- mental measure and human performance which is used to optimise the environmental conditions achievable with either ventilation or ventilation and refrigeration. A management control strategy based on the environmental measure which is designed to ensure that work in environments where excessive physiological strain may occur is prevented and corrective action is initiated. The environmental measure that reflects physiological strain is the link between the three elements and, since the turn of the century, the discussion of the merits of various indices has been prolific. One problem in selecting a suitable measure or index is the ease with which it can be physically obtained relative to accurately reflecting the physiological strain. For example, wet bulb temperature is simple to measure and, for a particular mining sys- tem, it may adequately represent physiological strain, however, it would not necessarily provide the same relatively safe measure in a different mining system. The acceptance of a measure which can be universally applied has been confounded by both development and predisposition. That is not to say that there is only one "correct" measure and all others are unsuitable. It is self evident that if the application of a particular index has resulted in adequate control, then that mea- sure is correct for that situation. However, an understanding of the limitations is necessary to ensure that adequate control is maintained as mining conditions change. Almost 100 years after the question of heat stress in mines started to be dealt with in a collective manner, an analysis of the available information is leading towards a general strategy to control this problem. In the paper, the developments in heat stress assessment are briefly examined and followed since the earliest published observations on the effect of heat in mines (Haldane, 1905), efforts to determine a relationship between an environmental measure and human performance are reviewed and summarised and the benefits of control strategies such as acclimatisation and shortened shifts are discussed as they relate to Mount Isa Mines. The results of testing the prototype air cooling power instrument are discussed and a heat stress control strategy outlined. HEAT STRESS AND AIR COOLING POWER The operation of the human engine is analogous to other engines where the conversion of chemical energy from the oxidation of fuel to useful mechanical energy is not 100% efficient. In a diesel engine it is about 33% and in a human engine less than 20% resulting in at least five times as much heat produced by the meta- bolic process as useful work done. Metabolic energy production is related to the rate at which oxygen is consumed and is about 340 W for each litre of oxygen per minute. Using measured oxygen consumption and an average body surface area of 2.0 m2, the approximate metabolic energy production associated with different mining tasks is (Morrison et al. 1968):- • Rest, 50 W/m2 • Light work, 75 to 125 W/m2 (machine, LHD or drill jumbo operators) • Medium work, 125 to 175 W/m2 (airleg drilling, light construction work) • Hard work, 175 to 275 W/m2 (barring down, building bulkheads and timbering) • Very hard work, over 275 W/m2 (shovelling rock) Heat balance is achieved when the rate of producing heat (the metabolic heat production rate) is equal to the rate at which the body can reject heat mainly through radiation, convection and evaporation. Heat exchange between the lungs and the air in- haled and exhaled is normally less than 5% of the total and there- fore usually ignored. Any heat not rejected to the surroundings will cause an increase in body core temperature. Since heat stress is related to the balance between the body and the surrounding thermal environment, the main parameters required to be known when determining acceptable conditions are those associated with the heat production and transfer mechanisms. These can be summarised as follows: Metabolic heat production rates (M - W) Skin surface area (A3) (and effects of clothing) Dry bulb temperature (t[ ]) Radiant temperature (t[ ]) Air velocity (V) Air pressure (P) Air vapour pressure (e [ ]) The rate of heat transfer to or from the environment depends on the equilibrium skin temperature t, and the sweat rate S,. These in turn depend on the response of the body to the imposed heat stress and the effect of thermoregulation (Stewart, 1981). Thermoregulation The body contains temperature sensitive structures which send impulses to the brain at a rate depending on the temperature. Both hot and cold signals can be differentiated and the thermoregulatory response ahivated according to which signal pre- dominates. If "cold" signals are dominant, body heat loss is re-

Jan 1, 1997

By Jerry F. Fountain

Variations in ore grade, mineralogy, and copper pricing structures over the life of the Inspiration mine have mandated many modifications to the treatment methods to maximize process economics. In the 1970's, copper prices generally declined, while inflation, wages, and interest rates increased. A metallurgical treatment route had to be developed for this continuing economic climate which would be capable of minimizing labor, energy, and capital cost requirements. After many years of development, the patented "Ferric Cure" process was introduced to satisfy these requirements. This dump leach process for treatment of mixed oxide/sulfide ore includes: strict mineralogical control of ore placed for leaching, controlled leach pad construction, solution saturation and curing of the pads with higher acid concentrations, and, finally, rinsing of the cured pads for removal of dissolved copper. Leach solutions, high in sulfuric acid during the cure application and low in sulfuric acid during the rinse, contain sufficient ferric iron to enhance the leaching of chalcocitic sulfide minerals.

Jan 1, 1983

By Kendrick C. Hardcastle

The practice of transporting an ore or matrix from a pit area to the plant process area by means of a hydraulic pipeline has long been used by the mining industry. The industries which have classically used hydraulic transportation of ore to the plant include the phosphate mining industry, the heavy minerals mining industry, the clay mining industry, and the sand mining industry. As the advantages of this method become better known throughout the mining industry as a whole, and as techniques and expertise improve, its use will undoubtedly spread. Its use is presently being contemplated in iron mining diatomaceous earth mining, and several industries where massive removal of overburden is a predicate to economical mining. The widely recognized advantages of hydraulic transport at ion of ore from the pit area to the mines are: 1) Its relatively low initial capital costs. 2) Its speed of relocation at the mine site. 3) The washing and scrubbing action given to the ore by its hydraulic passage into the pit pump and the subsequent trip through booster pumps down the pipeline to the plant.

Jan 1, 1969

By Clarence O. Babcock

A simple robust rock bolt load gage was tested in the laboratory to define its characteristic behavior and to obtain a measure of its performance. The gage uses three vibrating wire sensors crimped 120 degrees apart into the outer surface of a hollow cylindrical steel tube. The resonant frequencies of the wires change as the gage is loaded. This change is read with a Creare meter developed for the Bureau on a previous contract to read borehole stress gage results. A statistical analysis of data obtained defines the variables influencing results. A U. S. patent (3,914,992) assigned by the author to the Department of the Interior was granted October 28, 1975.

Jan 1, 1976

By Janine L. Beazley, James H. Kyle

The effects of pH, pH modifier (lime or caustic soda) and cyanide on the pulp rheology of a number of ore types ranging from highly siliceous to highly kaolinitic has been investigated. All experiments were performed in fresh water at solids concentrations of 25 and 45% solids and in the pH range 6 to 11. The kaolinitic ores exhibited greater changes in rheology with pH and calcium ion concentration than did the siliceous ores.

Jan 1, 1989

By Jon A. Hummer, Aleksandar D. Bugarski, Shawn Vanderslice, Teresa Barone

A study was conducted to examine the potential of diesel emissions control strategies based on retrofitting existing power packages with exhaust aftertreatment devices and repowering with advanced power packages. The retrofit systems, a diesel oxidation catalyst (DOC) and diesel particulate filter (DPF), were evaluated individually using a US EPA tier 2 (ter 2) engine operated under four steady-state conditions and one transient cycle. The DOC effectively curtailed emissions of CO, and to some extent organic carbon (OC), elemental carbon (EC), and aerosol number concentration. The DPF system offered substantially higher reductions in OC and EC mass and aerosol number concentrations. Both, the DOC and DPF achieved reductions in the aforementioned emissions without adversely affecting emissions of NO2 and nano-sized aerosols. The strategy of repowering with an advanced system was examined using a US EPA tier 4 final (tier 4f) engine equipped with a cooled exhaust gas recirculation system and diesel exhaust fluid-based selective catalytic reduction system, but not with a DPF system. The tier 4f engine contributed substantially less than the tier 2 engine to the EC and OC mass, aerosol number, and CO, NO, and NO2 concentrations. The tier 4f engine was very effective in reducing aerosol mass, NO, and NO2 concentrations, but it was not equally effective in reducing aerosol number concentrations. The implementation of viable exhaust after treatment systems and advanced diesel power packages could be instrumental to the underground mining industry to secure a clean, economical, and dependable source of power for mobile equipment.

By Raivo Maripuu

The Boliden Group encompasses Sweden's foremost operations related to the mining and production of copper, lead, zinc, precious metals and metallic by- products. It is also the dominant swedish producer of sulphur-based heavy inorganic chemical products and fertilizers and has an international trading organization covering, in adition to the group's basic products, industrial minerals and oil. Boliden's activities in- clude the marketing of proven Boliden technique and know-how. Boliden Metall - the mining and metallurgical company within the Boliden Group - produces about 13 million mtpy of ores at mines in northern and central Sweden. Boliden has, over the years, become a specialist in processing poly- metallic sulphide ores and its eight concentrators presently serve 15 mines. Boliden has a long history of close cooperation with Swedish and foreign manufacturers in developing new products and processes.

Jan 1, 1979

By Daniel R. Hack

Spatial relationships among physical 'and chemical properties pertinent to economic development of sand and gravel deposits have been little studied. Models need to address trends or zonation of material properties applicable to mine evaluation and planning or as a guide among deposits for use in regional assessment Models can then be utilized to design sampling programs to optimize additional data acquisition. Development of a preliminary methodology in the lower Boise River Valley, western Idaho, will utilize historical and recent data from a terrace-gravel deposit. Classical statistics and techniques of spatial data analysis will be evaluated as a precursor to formal geostatistical evaluation.

Jan 1, 2002

By T. M. Campoy, J. R. Jones

When extending the life of an existing mine in Appalachia, it is common to acquire the adjacent reserves and extend the existing mine into it. The existing mine is often renovated to accommodate the new conditions. The existing mining system and the track and belt haulage systems may he modified while the new property is integrated into the old one. All of these changes create new constraints for the mine ventilation system (MVS) that require proper planning and control procedures. This paper presents a study that was carried out for the ventilation system of a newly expanded underground coal mine in the Appalachian region. The process of correcting the ventilation system of the existing mine is discussed. That is followed by a discussion of some of the stages of controlling the expanded system. Numerical data for these steps are also presented.

Jan 1, 1994

By G. T. Adel

This paper presents the highlights of a general-purpose simulator for mineral processing plants that is being developed at the University of California, Berkeley. The state-of-the-art structured design methodogy based on a top-down design approach is being used to construct a modular and completely structured simulator such that it is independent of the unit operation models and routines. The simulator provides for two levels of operation allowing prebuilt or user-built simulation flowsheets depending upon the degree of computer knowledge expected of the user. The philosophy used in designing this simulator appears to be unique in the field of flowsheet simulation. The paper also includes a mini-example demonstrating the usage of the simulator.

Jan 1, 1982

By D. E. Munson

To assure the safety of a radioactive-waste repository, the performance of the repository must be predicted far into the future. The Waste Isolation Pilot Plant (WIPP) Program is responsible for developing the technology for such performance predictions in bedded salt. An important technology-development activity concerns the, fielding of very large-scale in situ tests to determine the time-dependent deformation of underground openings in salt as a basis for validation of the predictive technology. This technology is necessary to predict repository seal performance and final closure times of rooms and may be of value to the salt and potash mining community, as well.

Jan 1, 1992