Search Documents

By Zhikai Wang, Wensheng Lyu, Peng Yang

"To better understand the mechanical behavior of the compression deformation of backfill under high stresses corresponding to large depths, consolidation compression tests were performed for cemented tailings backfill with a cement-sand ration of 1:10 and 30% water under confined conditions. After applying different loading stress functions from 0.5 MPa to 32 MPa, the final axial deformation of the test specimen of backfill was obtained, and the micromorphology of backfill was studied before and after consolidation by scanning electron microscopy. Additionally, fitting analysis was performed for backfill confined compression deformation data and device model constitutive equations by the minimum square law. The constitutive model was revised according to the analysis results. The research results indicate that, as the load increases, the void ratio e obeys the functional relationship e=alnt + b (where a and b are fitting constants and t is compression time). Under the high-stress conditions of confinement, the constitutive model of backfill consolidation and creep can be used to describe the creep behavior of the backfill. Under high-stress conditions, after the consolidation of the confined backfill, the space between the tailing particles diminishes, the particles becomes more compact, and particle slippage occurs. INTRODUCTION With the depletion of shallow mineral resources, the mining industry has gradually shifted to deep mining (Zhang, Li, An, and Huang, 2010). Furthermore, with the continuous introduction of sustainable development policies regarding development and utilization of mineral resources, the mining industry must protect the limited available land and make full use of mineral resources as much as possible (Sijing, 1994; Zhihua, 2009). Backfill mining technology offers an unparalleled advantage in fully recovering mineral resources, controlling pressures, and improving environmental protection. As a result, this method has been widely used in various countries in the world (Burd, 2002; Benzaazoua, et al., 2008). Of the underground mines in the world, 45% of the large and medium-sized non-ferrous-metal mines and 37% of the gold mines use backfilling (Fuhrman, et al., 2014; Khaldoun, Ouadif, Baba, and Bahi, 2016). In addition, 45% of underground non-ferrous-metal mines and 37% of the gold mines use the filling method (Mchaina, Januszewski, and Hallam, 2001). According to incomplete statistics, more than 80 metal mines operate at a depth of more than 1 km; the depths of several typical deep mines are shown in Figure 1 (Burd, 2002; Fall, et al., 2009)."

Jan 1, 2017

By Stephen C. Tadolini, Peter A. Gray, Robert Hawker, Andrew Sykes

"Self-drilling rock bolts (SDRBs) that use pumpable cement grout to anchor bolts have been used successfully in the tunnelling and civil engineering industries for many years. Pumpable cement grout offers a considerable advantage in that the SDRB can be fully encapsulated right down to the bearing plate, including filling cracks and cavities in the borehole. However, cement grout cannot provide the immediate rock support required for the coal industry. This paper describes a new SDRB system that uses pumpable resin to anchor the SDRB in a borehole, which not only provides all the advantages of a pumpable grout anchoring system, but also provides immediate roof and rib support as required in the coal industry. This paper further outlines the latest developments in SDRB technology including (1) extendable self-drilling rock bolts, which can almost double in length during the installation process and are particularly suited to low seam heights and rib support and (2) pre-tensioned SDRBs, where a pre-tensioned load can be applied during the installation process. These new SDRB systems offer both considerable advantages in rock support and improvements in mining productivity.INTRODUCTIONThe mining industry is continually striving to develop more efficient methods to support the roof and walls of roadways and tunnels, and rock bolting has proven to be one of the most significant improvements in ground support over the last 50 years. Rock bolting is now almost universally used in the underground mining industry worldwide, and there are many different rock bolts available.Rock bolts are traditionally made from steel or fiberglass and are anchored into a borehole with a friction-anchoring device, such as an expansion shell mechanism; cement grout; or chemical resin. Friction-anchored bolts are widely used in the Australian metal mining industry, predominantly as short-term support. They are used in conjunction with resin-anchored bolts where there is a requirement for longer life. Resin-anchored bolts are used in the coal mining industry.Friction-anchored bolts provide immediate rock support, but their load transfer capacity is poor compared to resin or cement anchored bolts. In addition, friction-anchored bolts are more susceptible to corrosion than resin or cement anchored bolts."

Jan 1, 2010

By Christopher Mark

The Analysis of Retreat Mining Pillar Stability (ARMPS) program has been used to evaluate room and pillar retreat mining layouts since it was first released in the mid 1990s. After the Crandall Canyon mine disaster focused attention on the importance of pillar design, ARMPS became an essential component in most Roof Control Plans developed by mine operators. In 2010, NIOSH released ARMPS version 6, which features a ?pressure arch? loading model for deep cover room and pillar mining. NIOSH has also provided general guidance for using ARMPS, including design criteria based on statistical analyses of an extensive case history data base. Many real-world retreat mining scenarios entail mining configurations that ARMPS does not directly address. Some of these situations that the MSHA Roof Control Division (RCD) has encountered in the course of its reviews of more than 100 ?complex and non-typical? plans are ? Unmined pillars are left at the mouth of a retreat panel that function as a ?composite barrier pillar? ? The floor is extracted on retreat, increasing the mining height ? More than one row of bleeder pillars is left in an adjacent, previously mined panel ? A retreat panel is located above or below a gob area in a previously mined seam ? Bleeder pillars are partially extracted on retreat RCD has developed solutions that allow these situations to be fitted into the ARMPS framework, and these are presented in this paper. Also discussed are some of the rules of thumb that have been developed for various input parameters, such as the treatment of inseam rock and slab cuts into solid coal.

Jan 1, 2011

By Denise Mueller, Axel Preusse

"In 2010, the fracking discussion in Germany caused a number of changes in German law, which came into force in 2016. Especially the production of gas had to be regulated. With the legislation amendment, the “Subsidence-Area Mining Regulation” (in German: Einwirkungsbereichs-Bergverordnung) has been revised, too. The changes expand the compensation of mining damages, especially to the extraction with drilling from the surface and underground storage. Although the “Subsidence-Area Mining Regulation” has been revised, the area of main influence (subsidence of 10 cm) remains to determine a relevant boundary for mining damages. The determination and prediction of this boundary above caverns are presented in this paper. In addition, further elements of ground movements and their relevance to mine damages are analyzed. The usage of the area of main influence to fix a relevant boundary for mining damages does not correspond to the relevant elements of ground movements. A limit for differences in subsidence (tilt) or horizontal changes in length should be preferred to describe the relevance of mining damages on buildings. Furthermore, this paper outlines the the meaning of using the area of main influence to fix a relevant boundary for mining damages. INTRODUCTION The “Federal Mining Act” (in German: Bundesberggesetz, short: BBergG) forms the central legal standard to cover subsidence in Germany. The mining authority refers to the following regulations (Preuße et al., 2015): the “Subsidence-Area Mining Regulation” (in German: Einwirkungsbergverordnung, short: EinwirkungsBergV; since 1982) the “Mine-Surveyor Mining Regulation” (in German: Markscheider-Bergverordnung; short: MarkschBergV) the “Deep-Drilling Regulation”"

Jan 1, 2017

By Brian E. Perrine

Underground mining requires a variety of specialized equipment. With ever-changing mining conditions and methods, some mines have had to resort to purchasing existing industrial equipment and adapting it for underground use. Since this equipment is not made for underground mining or their specific task, the result is often lost time, money, and sometimes an unsafe working condition. One such application is the setting of a CAN. A CAN is a type of cylindrical secondary roof support made from a cement composite and encased in steel. The CAN has become popular because of its simple one-piece design that can handle heaving and sagging better than other available designs. ?Because of this exceptional ability to sustain load through extended convergence and displacement, the CAN is one of the most robust and stable standing supports in use today.?It also promotes better air flow due to the size and shape of the CAN. CAN size and weight have increased over time to handle more difficult mining conditions. Significant down time and inefficiencies with existing CAN setting machines at Twentymile Coal were directly due to the item in use not being designed to be task-specific. They were undersized with very limited movement. The miners had to take extra steps and precautions when setting CANs. Maintenance delays were significant. Twentymile Coal Company realized that they required a safer, more reliable and more efficient machine to handle and set CANs, and looked for a partner to develop a new design-specific machine. They worked jointly with J.H. Fletcher® engineering and sales to design and manufacture a machine specifically made for setting CANs. The objective was to produce a machine that would handle the conditions and methods that the mine required for setting CANs during longwall retreat. The resulting design had to be safe, stable, have a wide range of motion, be ergonomic, simple to use, and easy to maintain. The machine also had to improve efficiency. The resulting machine has been operating for approximately one year at Twentymile Coal and has been proven to improve safety, reliability, and efficiency. In conclusion, with the task-specific CAN Manipulator, the mine is able to better plan daily tasks with the knowledge that the machine will be available throughout a shift, and the employees will be safer because of the machine?s ergonomics, stability and safety. This has resulted in better productivity and a safer environment.

Jan 1, 2013

By Wilfried Ufer

[1. Einführung in die Problematik 1.1 Die Bedeutung des Schildausbaus Seit fast 30 Jahren ist die Konkurrenzsituation auf dem Primärenergiemarkt der Bundesrepublik Deutschland durch einen von Erdöl and Erdgas geführten and insbesondere gegen die Steinkohle gerichteten Verdrängungswettbewerb gekennzeichnet, der den Steinkohlenbergbau zu tiefgreifenden RationalisierungsmaBnahmen zwang. In diesem Zusammenhang kam es Anfang der 70er Jahre zur Einrührung des Schildausbaus, der eine erhebliche Produktivitätssteigerung in den Strebbetrieben zur Folge hatte and damit die Uberlebenschance des Steinkohlenbergbaus in der Bundesrepublik Deutschland enorm verbesserte. Der Grund hierfdr lag darin, daB der Schildausbau im Vergleich zu dem vor ihm eingesetzten Rahmen- and Einzelstempelausbau eine wesentlich hdöhere Ausbauleistung erbrachte, weil er sich weit weniger empfindlich gegen Hangendausbruche and aus dem Alten Mann hereinbdschende Bruchberge erwies. So erklärt sich auch die stürmische Entwicklung and die schnelle Verbreitung des Schildausbaus. Bereits 1975 stammte rd. 50 % der Fdrderung aus Schildstreben, 1990 waren es fiber 75 % and heute sind es fiber 90 %. 1.2 Die Staubentstehung beim Schildausbau Die Erfolge des Schildausbaus sind unbestritten. Jedoch nahmen :nit seiner Einführung die Probleme der Staubentstehung and Staubbekämpfung im Vergleich zum Ein zelstempel- and Rahmenausbau erheblich zu. MaBgebend dafür sind hauptsächlich folgende Gründe: - Abbau von dozen nit gebrächen, weichen Hangendschichten, die erst durch Schildausbau abbaubar wurden, - Zerkleinerung des auf den breiten Kappen aufliegenden Bergematerials infolge der höheren Ausbaustiltzkrafte des Schildausbaus, Zermahlen der sick in die Spaltabdichtungen hineinarbeitenden Bergestückchen, - Erhöhung der Wettergeschwindigkeit infolge der durch die Baufarm des Schildausbaus bedingter. Verkleinerung des Strebquerschnitts verbunden mit der Aufwirbelung and Aussichtung von Staub, - Aufwirbelung von bereits abgelagertem Staub im Bruchraum beim Hereinbrechen der Dachschichten. Die genannten Gründe treten zumeist nicht in jedem Abbaubetrieb gleichzeitig auf. Sie rind vielmehr u.a. abhängig vom Ausbautyp, von den Gebirgsverhältnissen and von der Abbaugeschwindigkeit. Trotzdem ergeben sich beim Vorrücken des Ausbaus in der Regel hohe Staubkonzentrationen, die deswegen besonders kritisch sind, weil es sich um quarzhaltigen Feinstaub handelt, der besonders gesundheitsschädlich ist. Die Hauptzutrittsstelien]

Jan 1, 1984

By Dakota Faulkner

Unexpected roof falls often occur in the entries or intersections of active mining sections in underground mines. For large roof falls (greater than 20 ft in height), it becomes dangerous and impractical to clean up the rock debris and re-bolt the newly exposed roof strata. To help mine operators rehabilitate the roof fall areas in a quick, safe, and economic manner, Jennmar Corporation and Keystone Mining Services, LLC (KMS) designed, tested, and developed various impact-resistant (IR) steel set designs, as initially detailed in the proceedings of the 30th International Conference on Ground Control in Mining (ICGCM). Since then, the IR steel sets have been successfully installed in more than 100 roof falls in 43 different coal mines. Significant data has been obtained from these installations, enabling further refinement to and improvement on the design. This paper (1) updates drop test results of the IR lagging panel, (2) presents a case study of the performance of IR arch sets installed 56 months ago at a roof fall rehabilitation site, (3) demonstrates capacity evaluation of the IR steel set, and (4) outlines a preliminary applicability evaluation guideline of the IR steel set for a given roof fall condition. Field evaluation and structural numerical analysis indicate that impact capacity of the system is significantly higher than that of the IR lagging panel, as originally determined. It is concluded that, when evaluating the applicability of an IR steel set, ground control engineers should consider the IR lagging and steel set as an entire system and make a reasonable engineering decision based on actual roof fall geotechnical conditions.

Jan 1, 2014

By Kevin J. Ma, John Stankus

"In order to access remote reserve areas, some U.S. coal mines have to maintain aged underground entries for a great distance. However, high humidity, warm temperature, and time dependent deterioration can cause progressive roof deterioration and unexpected roof falls can, pose a great challenge to ground control engineers. With an active belt structure in place and limited space, re-bolting becomes very costly, less effective, and, sometimes, impractical and unfeasible. To gain long-term entry stability and serviceability, operators typically rehabilitate the aged belt entries by installing standing steel set supports. In the last several years, Keystone Mining Services, LLC, (KMS) has assisted many coal mines with their belt entry rehabilitation projects, evaluated the ground condition of various aged belt entries, and designed different standing steel set support systems. This paper presents a case study of a large-scale roof fall that occurred at an aged belt entry in a mine located in an eastern coalfield, analyzes root causes of excessive deformation of square sets that were installed in an adjacent entry, evaluates the adequacy of an existing rehabilitation square set, and develops remedial recommendations for future rehabilitation practice. Based on the case study, the paper outlines design guidelines for rehabilitation steel sets that include field evaluation, engineering considerations, design assumptions, steel structural analysis, and field installation quality control. INTRODUCTION With gradual depletion of shallow coal reserves, some underground coal mines have to maintain long-term entries (belt, track, return airway, etc.) for a great distance in order to access remote coal reserve areas. However, due to high humidity, warm temperature, and aging in the belt entry, roof strata weathering and pillar degradation become more and more severe. Progressive roof deterioration poses a great challenge to ground control engineers. Pillar rib sloughs at certain locations, entry width increases in some areas, immediate roof sags, immediate roof rock falls out between bolts, existing bolts lose functionality due to corrosion, cutters develop deeper in corners, and strata separation develops deeper up into the main roof. As a result, unexpected roof falls occur in a random manner resulting in loss of production, damage of belt structure, and even injuries to underground personnel."

Jan 1, 2017

By Thomas A. Cook

The effectiveness of tensioned roof bolt systems has been well researched and documented over the years (Stankus, 1990, 1991, 1997; Guo, 1997; Denton, 2000; Su, 2007). Higher and more consistent installed tension has been shown to improve the beaming effect and associated roof stability especially in highly-stressed, weak, laminated roof strata. To accomplish higher and more consistent bolt-installed tensions, various types of anti-friction washers have been developed and applied to many types of tensioned roof bolt systems. In addition to increasing bolt-installed tension, these washers also provide a lubricating effect that minimizes sparking during the bolt torqueing cycle. The most popular and widely used anti-friction washer configuration consists of a plastic washer that is used in conjunction with a standard hardened steel washer. This washer configuration has performed well in the field in terms of increasing the bolt-installed tension (or plate load) and the related tension/torque ratio (the amount of tension achieved per one ft-lb of applied torque). However, the installed tension does not always maintain consistency. One reason for this inconsistency is that the plastic anti-friction washer sometimes dislodges and shreds or tears before the bolt torqueing cycle is complete. This condition prevents the plastic washer from acting as an anti-friction medium for the entire torqueing cycle. Jennmar Corporation and Keystone Mining Services, LLC, developed the ?TT? washer in early 2012. The ?TT? anti-friction washer is comprised of two zinc-coated (galvanized) hardened steel washers that are joined together with an exclusive polymer. The ?TT? washer has been extensively tested and applied in the Sewickley, Pittsburgh, and Indiana #5 coal seams. The test results indicate an average increase in installed load and tension/torque ratio of 20%. More importantly, the installed load consistency improved, with a significant reduction in the standard deviation of values. This paper will detail the development and testing of the ?TT? anti-friction washer with case studies of actual mine applications.

Jan 1, 2014

By Xingkai Wang, Wenbing Xie

"To control the large deformation of soft rock around the roadway subjected to high stress, it is important to improve the stability of support structure, in addition to increasing support strength. In this study, the causes for the destabilization of U-steel frame and its loading characteristics were analyzed by theoretical analysis, laboratory experiments and field tests. The technology of constant support resistance, the principle of support structure compensation and the compensation technique are proposed. The results indicated that the main reasons for frame structure destabilization are caused by low strength of connector, irrational structure of connector, poor interaction between the surrounding rocks and support frame and structure, and unstable support structure. Thus, the corresponding technological measures, such as connector with high strength and rational structure are adopted. The bearing capacity of frame is unstable after slipping. In order to maintain the high support resistance when the frame is performing the support function, the frame connector should be retightened after slipping. Though the working resistance may be improved greatly by using the backfilling or back grouting of U-steel, the frame remains unstable because of the unstable frame structure. Therefore, according to the deformation characteristics of rocks surrounding the roadway and the structure instability of U- steel frame, the stable structure device is used to carry out the structural compensation of U-steel frame, and the whole bearing capacity of the frame and its structural stability are improved greatly.INTRODUCTIONThroughout the development of the roadway supports for coal mines in China, it can be seen that the supporting strength and supporting resistance increase continuously with increase in mining depth and supporting difficulties [1]. With respect to the ground control mechanism and supporting technology of rocks surrounding the soft rock roadways subjected to high stress, considerable research has been done both at home and abroad. The backfilling technology behind the high-resistance and yieldable U-steel wall, the new type of grout/bolt support technology and the bolting with high-strength mesh support technology were developed, and have been used widely in coal mines with notable economic benefits [2-7]. However, a large number of engineering practices show that in many cases the existing rock control technology of roadway may not control the large deformation of the soft rock roadways subjected to high stress. The reason that the large deformation of soft rock roadway occurs is mainly due to poor structure stability of existing frame bearing structure, not insufficient support strength."

Jan 1, 2015

By Tristan H. Jones

Rib-related accidents in underground coal mines continue to cause injuries and take lives at a rate of 1.3 fatalities per year for the last 17 years. Prevention of these accidents cannot simply be a matter of installing more rib support, though the eventual final solution will undoubtedly include that component. Ultimately, rib safety will be brought about through an understanding of the causes and mechanisms that cause rib fatalities, and by fine-tuning mining methods and procedures that are currently in place. This paper investigates the factors likely to be most influential in the occurrence of rib fatalities. A careful analysis has been conducted of the rib fatality reports documented by the Mine Safety and Health Administration between 1996 and 2013. The primary outcome is the determination of the relative impact of each type of rib fatality factor and a better understanding of the impact each factor has. Among the rib fatality factors considered, the influence of rib profileis considered for the first time. Mining height, rib stratigraphy, mining cycle, and the standing position of a miner next to a pillar are also considered. Questions are also raised about the current interpretation of rib fatalities due to mining depth, with the indication being that mines operating at the greatest depths may actually have the most respectable rib fatality record among all mining depths. Additionally, a new method of considering rib exposure is developed. Based on the results, recommendations are made for future work. By gaining a better understanding of how particular factors contribute to rib fatalities as opposed to rib failure or stability, it is hoped that future efforts can be more precisely directed towards the desired outcome of fatality reduction.

Jan 1, 2014

By Robert J. Coutts, Dan A. Payne

"The Broadmeadow mine is a punch longwall mine owned and operated by BHP Billiton Mitsubishi Alliance (BMA) in the Bowen Basin of Queensland, Australia. In 1999, an exploratory adit was driven as part of the feasibility study for the establishment of the mine. Subsequent development of the mine in 2004 started some distance away from the initial test adit. Ten years later, the trial adit would be used as the headgate of the 5'h longwall panel. However, multiple roof falls had occurred in a heavily jointed area over a distance of 1, 000 ft (300 m) during the past 10 years. Due to the immediate coal roof, low stress environment and time, some of these falls had progressed to 38 ft (11.5 m) above the mining floor. As a result of the extensive work involved and safety implications of trying to recover the roof falls conventionally, a strategy was developed to fill these roof falls with a cement based product from the surface, down boreholes, and redrive the roadways through the consolidated roof fall material. This paper describes the process of rehabilitating these roadways, the results when the roadway was redriven and the headgate performance as the longwall mined through the area.INTRODUCTIONBMA operates 7 open cut and 2 underground mines in the Bowen Basin of Queensland, Australia producing over 50 mt per year of high quality coking coal. As a result, BMA has established over 150 miles (250 km) of open cut highwall.Broadmeadow Mine is a punch longwall mine located 22 miles (35 km) north of Moranbah in Queensland, Australia on the western limb of the Bowen Basin Coal Measures (Figure 1). Broadmeadow Mine commenced development in 2004 and began longwall operations in 2005. Broadmeadow is currently completing the fifth longwall panel and produces over 4 Mt per year of high quality coking coal. Mining is undertaken in the Goonyella Middle Seam, which is 21 to 25 ft (6.5 to 7.5 m) thick in the current mining area.The mine layout required the use of an old exploratory gateroad as the headgate of its 5th longwall. This gateroad had experienced numerous large roof falls and required extensive rehabilitation."

Jan 1, 2010

By Houquan Zhang, Ming Li, Guimin Zhang, Bei Zhang

"The support quality of bolts in deep roadways is one of the important factors for efficient and safe coal production. A new kind of non-destructive testing technique and equipment was used to monitor the axial bolt load in real time in deep roadways. Based on the test results, the working status of bolt support in deep roadways was evaluated. The research results show that the variation characteristics of axial bolt load is consistent with the distribution characteristics of rock pressure no matter whether it is in the initial support stage or mining disturbance stage. The axial load of bolts located 20m outby the development face has an overall rising trend within 3-5 days after installation. Within a certain distance in the front abutment pressure zone in front of the face, the axial bolt load increases with the advance of coal extraction. When coal and rock in the abutment pressure zone yield, the axial bolt load is dropped correspondingly. This kind of non-destructive testing technique provides an advanced means of detection and evaluation on bolt support quality.INTRODUCTIONMany coal seams more than 800m deep are being mined in eastern China. Roadways of large cross-section are being developed in coal seams more than 600m deep in western China (Kang et al. 2014). Moreover, these roadways are commonly supported by roof bolts and have encountered many support problems, including soft rock strata, intense mining disturbance, and abnormal tectonic stress. The stability of its surrounding rocks is difficult to maintain, the roof bolt even fails before mining (Shen 2014; Jiang et al. 2015). Therefore, it is very important to develop an effective method to detect the bolt quality in real time and evaluate the bolt's safety status.During installation of roof bolt, the installation quality is heavily affected by installation equipment and tools, field conditions, and operators' skills (Li et al. 2005; Shan 2009). The anchorage length will be shorter than the designed one if the resin cartridges are pushed to the bottom of excessively long drill hole and stay there without being shredded and mixed. The support function of the bolt would be weakened by the shorter anchorage length."

Jan 1, 2016

By Gautam Benerjee, Veera Reddy Boothukuri, Bhattacharjee Ram Madhav, Panigrahi Durga Charan

"India’s tryst with mechanized longwall coal mining started with the introduction of the first self-advancing powered support longwall (PSLW) face at Moonidih Colliery of Jharia Coalfield in 1978 and at Godavarikhani (GDK)7 Incline of Singareni Collieries Company Limited (SCCL) in 1983. During the last 37 years, about 30 longwall units in Coal India, Ltd., (CIL) and 10 longwall units in SCCL have been introduced with powered roof supports of varying capacity, ranging from 280 to 800 tonnes, in many mines in India under varying geological and geotechnical conditions. The majority of the longwall faces in India have been worked under relatively shallow cover (up to 200m), and significant strata control problems have been encountered due to poor caveability of the roof, inadequate capacity of the supports, a lack of knowledge on longwall caving mechanisms, less than adequate strata monitoring systems, and the non-availability of quality spare parts, etc. This has resulted in structural damage to supports and increased downtime of the equipment, thereby making longwall mining in India a case of technology failure. Energy demand for a developing country like India with a population of 1.2 billion is huge, and the thrust on increasing coal production continues. However, the share of coal production from underground mines in India continues to decline (current share is around 6%) because of absence of successful mass production technology in underground coal mining. Under this backdrop, a high-capacity longwall with state-of-the-art technology was introduced in 2014 at Adriyala Longwall Project (ALP) of SCCL for the first time in Indian Coal Mining Industry. The first longwall panel (LWP) has been completed successfully. This paper highlights the major geotechnical challenges encountered during development of the longwall gate roads due to the presence of two overlying clay bands, significant in-situ horizontal stresses and the experience of using rigid (welded) steel wire mesh with resin-anchored roof bolts. Efforts have been made to analyze longwall weighting and caving behavior, such as main and periodic weightings, the effect of front and side abutment pressures, and the behavior of gate roadway support systems under immediate friable weak roof with overlying massive sandstone."

Jan 1, 2017

By Wenbing Guo, Yi Tan, Erhu Bai

"It is important to study the mining technology under structures for raising the coal resources recovery ratio. Based on the geological and mining conditions, the top coal caving harmonic mining technique in thick coal seam beneath the earth dam was put forward and studied. The 5 factors such as the panel mining direction, panel size, panel location, panel mining sequence and panel advance velocity were taken into account in this technique. The dam movement and deformation were predicted after the thick coal seam mining and the effects of mining on the dam were studied. By setting up the surveying stations on the dam, the movement and deformation of the dam were observed during mining. By taking some protective measures on the dam, the top coal caving mining technique in thick coal seam beneath the earth dam was carried out successfully. The study demonstrates that harmonic mining in thick coal seam is feasible under the dam. The safety of the earth dam after mining was ensured and the coal resources recovery ratio was improved.The surface movement and deformation caused by coal mining not only influence the ecology environment in the mining area, but damage the surface structures such as buildings, railroads, highways, water bodies and damsr1-31_ The movement of strata and surface caused by mining had disturbed various aspects of industrial and agriculture productions in the mining arear41. The earth dam is a very important water retaining structures, so it must makes sure the safety of dam if mining under it. Therefore, to study the effect of mining on dam and control measures to ensure safety of mining under the dam are important factors for improving the mining recovery ratio, reliving the mining continuity, preventing or reducing damage to the dam.By means of the harmonic mining technologyrs1, theoretical analysis and field observation, the mining method under an earth dam and the mining influences were studied and analyzed in this paper. The mining of a thick coal seam under the dam was carried out safely and successfully."

Jan 1, 2016

By Andrew Lewis, Amarit Nitaramorn, Alexander Garcia, Peter Altounyan

"Indonesia is a major coal producer, the vast majority being sourced from opencast operations. Underground production to date has been constrained by unfavorable ground conditions and limited local experience. However, an underground trial in East Kalimantan has now shown that it is possible to successfully extract coal and mine safely, despite the technical challenges.A trial drift mine has been worked to a current maximum depth of 160 m (525 ft) in a dipping coal seam. The 3 m (10 ft) thick coal seam is overlain by very weak mudstone and sandstones. The mudstone forming the immediate seam roof strata proved a particular challenge given its adverse reaction to water and overall friability.Rock bolts were used as roadway support, the system being carefully selected to optimize effectiveness. An innovative method of partial extraction was trialed, which demonstrated the potential for productive mining despite the ground conditions. Roof falls have occurred within the working area, and roadways demonstrate reasonable stability over time.Throughout the course of the trial, strata behavior monitoring has been an important aspect, and a comprehensive ground control monitoring system is in place. This has enhanced the ability to increase the level of support where required and to react to deteriorating conditions. In addition, monitoring information has allowed a quantitative assessment to be made of the technical feasibility of future full-scale mining.INTRODUCTIONWith current production at over 200 million tons, much of this destined for overseas markets, Indonesia is the second largest exporter of coal (Ritschel and Schiffer, 2007). The majority of the coal is sourced from the Kalimantan coalfields. Mining is predominately opencast, yet in recent years there have been attempts made to introduce underground operations. This move would permit continued access to good quality seams that are beyond the reach of viable opencast mining."

Jan 1, 2010

By Chris Kelly

The Monroe County Quarry is an open pit granite quarry located near the town of Bolingbroke. Monroe County. Georgia. The quarry has been in continuous operation for approximately 10 years. The quarry covers approximately 27 acres and has an annual production rate of 1.0 million tons. On the morning of April 26. 2000 a sudden rapid highwall failure occurred at the west end of the north wall of the quarry pit. The failure occurred approximately one hour after a three inch-wide crack was observed in an access road located at the crest of the highwall. No indications of failure had been observed prior to the development of the crack. The active mining area had been at the base of the failed area. The pit was successfully evacuated prior to the failure and there were no losses of either personnel or equipment. The amount of failed material was estimated to be in excess of two million tons. In order to ensure a safe working environment at the quarry a slope monitoring program was established in the area of the failure. The program consisted of using an EDM survey instrument to periodically measure the location of survey prisms installed at carious points on the north wall. The locations of the prisms were recorded over several months and changes in location were analyzed in order to identify and characterize the movement of the failed mass. The results of the analysis provided a basis for recommendations regarding access to various areas of the quarry. This paper discusses the factors contributing to the failure, the method of post-failure slope monitoring, anti the interpretation of the monitoring data.

Jan 1, 2002

By Yongping Wu

Taking the longwall mining face area in a steeply dipping seam as the research object, the stability of an asymmetrical rock mass structure is analyzed using shell theory and masonry beam theory. The results show that an asymmetrical shell structure is formed at the top strata of the mining stope and its magnitude is mainly determined by the mechanical characteristic of the overburden strata of working face, mining space size and so on. Localized instability of the shell structure is the main factor that leads to the overall structural instability in the stope. The instability modes includes: the shell roof instability dominated by tensile failure, the shell shoulder instability initialized by compression-shear failure, and shell bases composite instability occurs in tensile and compression-shear modes. The shell structure stability dedicates rational strata control measures to choose, and the caving height of overburden strata is the key for shell structure instability.

Jan 1, 2013

By Pengfei Wang, Guorui Feng

"The angle of break is the acute angle created by the coal seam bedding plane and caving line formed by roof strata movement after extraction of a longwall panel. It has a significant influence on stress redistribution both in the gob and abutment. Throughout numerical simulation investigations up to now, little attention has been paid to it, or an angle of break of 90° was used, which, however, is not realistic. This paper presents a detailed numerical modelling incorporating the angle of break against Zhenchengdi Coal Mine. The angle of break was obtained through cross-measure boreholes. Hoek-Brown constitutive model was used to simulate the rock masses. Double-yield constitutive model, which was best fitted by Salamon’s model, was used to simulate the gob. The results show that a “/ \ shape” shear failure zone develops around the gob. The shear failure in the floor along the panel edge is due to opposite shear of rock mass on two sides of the caving line, and the number of yielded zones within the gob floor close to the gob edge is smaller. According to the research, the entry was determined to be driven under the gob edge employing split-level longwall panel layout (SLPL). The other numerical simulation for SLPL shows that stress around the god-side entry is much smaller than pre-mining stress, and the area of intact rock mass at the elevating section is larger than conventional layout. Numerical modelling was then validated by field observation.INTRODUCTIONTo solve low recovery and ground control problems in longwall mining with top coal caving (LTCC) due to large gate pillar or chain pillar, gob-side entry approach is becoming increasingly popular (Nazimko, 1994; Li et al., 2016; Zhao, Wang, and Su, 2017). Gob-side entry is actually a combination of the gateroad, pillar, and gob, which is a typical panel layout with slender pillar or artificial pillar or wall. The abutment load has a profound impact on stability of the gate pillar, as well as the gob-side entry. Better estimates of abutment loading profiles will result in improved evaluations of design of pillar and gob-side entry (Larson and Lavoie, 2016)."

Jan 1, 2018

By David A. Newman

Severe roof control problems have plagued a West Virginia underground mine since its initial development in the late 1970's. Adverse roof conditions in the Eastern portion of the reserve result from a combination of mining: - perpendicular to the major principal horizontal stress direction, - near lineament intersections, - in areas where the ratio of horizontal stress to vertical stress exceeds 2.00 to 4.00, and - where laminated strata are present in the immediate roof. The focus of this study is to identify the engineering (mine orientation, roof safety factor) and geological parameters (lineament and horizontal stress orientation, horizontal to vertical stress ratio, and immediate roof lithology) causing poor roof conditions and to quantify their influence on projected mining conditions in the Western portion of the reserve Rose diagrams were used to illustrate the correlation between the orientation of eight hundred thirty-six (836) roof falls with that of forty-four (44) lineaments and the principal horizontal stress Similarly a composite map was used to demonstrate the relationship between roof falls and the ratio of horizontal stress to vertical stress The immediate roof strata across the property were categorized as either laminated or non-laminated based upon a thorough examination of one hundred sixty-two core logs. The presence or absence of fireclay, a rider coal, and carbonaceous shale was also noted because of the historic correlation with poor roof conditions. Rock strength and physical property tests were conducted on selected immediate roof strata recovered from coreholes drilled along the mains projected to the Western portion of the reserve Potential roof control problems in the Western reserve were quantified based upon the correlations developed by analyzing engineering and geological data The main conclusion is that laminated roof strata, the rider seam, and its associated fireclay will have the greatest influence on mining conditions. Roof problems attributable to horizontal stresses will not be as severe in the West due to an increase in overburden depth and corresponding decrease in the stress ratio. Recommendations are provided for mining orientation, the layout of mains and submains, panel location, and roof support based on intended service life.

Jan 1, 1999