Search Documents

By Yao Yuping

The strength and deformation of more than two hundred coal samples have been tested in the condition of triaxial compression. The regression equation showing the relationship between coal strength and pressure in the pores as well as confining pressure, was obtained. The appropriate calculation for stress-strain curve was carried out. Further, an analysis shows the variation of coal strength and its modulus of elasticity in methane medium.

Jan 1, 1992

By Hideki Shimada

In underground coal mines, grouting method is employed in order to reinforce the floor and to control the movement of groundwater into the roadway. However, the seepage and the reinforcement behavior of the grouting material into the floor are not clearly understood. Therefore, grouting is today normally based on empirical relationships and on the experience of the grouting personnel. To assist grouting projects, it must be acknowledged that many of the flow and the hardening processes occurring during grouting so far defy mathematically analysis. From this point of view. this paper discusses the behavior of grouting material, when it is injected into the roadway floor, by means of 3-D Eulerian-Lagragian seepage analysis. Moreover, the effectiveness of reinforcement grouting on the mechanical properties of slaking-prone mine tunnel floor are studied by means of several laboratory tests. Keywords: Mine tunnel floor, Grout, Seepage, Reinforcement

Jan 1, 2002

By Thomas P. Mucho

To document the performance of mine roof and roof support systems the U.S. Bureau of Mines (IJSBM) has been installing instrumentation at selected sites in U.S. coal mines. Much of this support and roof instrumentation has been installed in high stress conditions to maximize differences in performance. Summarized in this paper are the results of four such site investigations. The roof geology at the four sites is quite different and is quantified using the USBM's Coal Mine &f Rating (CMRR). The studies included detailed measurements of roof movement using multi-point extensometers, as well as measurements and monitoring of bolt loading. The investigations include developmental loading and abutment loading from longwall and room-and-pillar mining operations. Some of the issues examined are the effect of the horizontal stress field, the effect of installed tension (torque-tension versus resin bolts), the effect of reduced annulus bolt holes, and the differences between similar bolts supplied by different manufacturers.

Jan 1, 1995

By Laxminarayan Holla

There exist many formulae for designing coal pillars. However, when applied to a given set of mining parameters, they lead to different pillar sizes and factors of safety. From the subsidence point of view, the pillars designed as protection pillars not only have to be stable, but also have to limit subsidence over them to a level acceptable to the structure being protected. The subsidence over a pillar of given width to height ratio depends upon the mining depth. A pillar may be stable, but the subsidence over it may be quite large and unacceptable for the structure. In many cases even though pillars may yield, they support the undermined strata and reduce surface subsidence. In addition, the yielding pillars eliminate peaks and troughs in the surface subsidence profile and reduce ground strains. In a given situation, whether a pillar yields or not depends primarily upon its width in relation to mining depth.

Jan 1, 1992

3-D finite element modeling was performed to study the effect of bedding plane sliding and separation and tensioned bolt in layered root It was found that the major influence zones of a tensioned bolt are restricted to the neighborhood of the anchor points; that bedding plane sliding and separation releases the vertical stress in the roof above entry but greatly increases the horizontal stress within the first layer of the roof, and that there is a triangular zone between the two adjacent bolts at and near the roofline level that is beyond the influence zone of the bolts which is liable to fail if conditions exist. Based on the results, three possible modes of roof failure are proposed for the design of tensioned bolting.

Jan 1, 2001

By Joachim Leonhardt

Hundreds ofbolt-indicators were already used successfully in the German deep hard coal-mines to increase the safety and economy. The bolt-indicator offers the simple possibility to show roof-bolt (anchor-) loads. to indicate weak points as well as to optimize the anchor density and the dimension: The bolt-indicator is mushroom shaped and consists of coated metal. It is inserted between the anchor plate and the flanged nut. The loads appearing at the anchor are transferred to the bolt- indicator and can be recognized visually at the cylindrical part by the amount of the surface coating. Examples are used to clarify the application aims, operation and usage of the bolt-indicator and its yielding advantages in practice.

Jan 1, 2001

By Khamis Y. Haramy

The U.S. Bureau of Mines installed surface and subsurface instruments at a mine site in Colorado to monitor and characterize the overburden response to longwall mining. Instrumentation included a time-domain reflectometry (TDR) cable, a multiple-point borehole extensometer (MPBX), vertical-deformation surface monuments, and in-mine pressure cells for monitoring abutment, pillar, and gob loads with respect to the longwall face position. The purpose of the study was to collect data that could be analyzed to correlate the design of the mine layout to the resulting overburden failure response. Determining the extent of caving and fracturing is important in the arid and semiarid Western United States because of the possible consequences to the fragile underground hydrologic systems upon which the land owners and users depend. This study is unique from past investigations because the overburden contains massive sandstone members that impose special conditions on the caving process and pressure redistribution above the longwall panels. This paper presents the results of this correlation study.

Jan 1, 1992

By David H. Y. Tang

The reinforcement mechanism of suspension effect is analyzed based on beam-column theory. The equations of the maximum bending stress, deflection and transferred bolt load for the bolted roof strata are derived. In the analysis, the bolt load is assumed to be point load and the horizontal stress is uniformly applied to each stratum. The reinforcement mechanism of friction effect is also analyzed. The major function of roof bolting in this case is to create the friction¬al resistance by tensioning the roof bolts, thereby the individual thin strata are "welded" into one single thick stratum. Based on the results, equal spacing of roof bolts is used in the suspension effect while for friction effect, the bolts should be spaced based on equal shear force concept. The design nomographs for the proper bolting pattern and bolt ten¬sion of mechanical roof bolting systems are presented for practical applications.

Jan 1, 1984

By Y. P. Chugh

About 60-70% of the underground mined coal in Illinois is extracted using a room-and-pillar mining method that permits extraction of about 50% of the coal. The remaining coal is left behind in the form of support pillars to control surface and subsurface movements. Illinois coal seams are typically associated with water sensitive weak floor strata whose thickness varies 0.31 - 1.3 m. The current mining geometry mostly uses pillars of constant size within a mining area. This traditional practice suffers from the disadvantage that pillars within the center region are subject to much higher loads than the pillars located on the outer edges of the panel. This results in a higher incidence of rib spalling, and roof falls, creating a potentially hazardous work environment. In addition, this concentration of loading at the center of the panel provides initiation points for floor failure to occur. The primary goal of this study was to reduce ground control problems and production costs in Illinois mines by considering alternate mining geometries. The development and subsequent field demonstration of an alternate geometry is presented in this paper.

Jan 1, 2004

By Ross Seedsman

There are many models for how roof bolts behave, one of which is prevention of shear along bedding. The basis of this model is that a roof beam will not delaminate if bedding parallel shear can be prevented. A key point in such a model is that bedding discontinuities are present naturally in the roof and that mining induced stresses do not generate new surfaces. The presence of these discontinuities means that the rock mass must be modelled as a transversely isotropic material if continuum codes are used. A limit-equilibrium type design method for specifying roof bolts is being developed using voussoir beam and excess shear force concepts. The method incorporates much of what operators know intrinsically about roof reinforcement, and allows mining engineers to focus on the key uncertainty - the frequency and location of bedding surfaces in the immediate roof. Areas where more research is required are highlighted.

Jan 1, 2000

By Khaled Morsy

In this paper a new method to evaluate the stability of yield pillars was introduced. The evaluation of yield pillar stability was conducted in three steps: (1) Estimation of pillar loading - numerical modeling is a good tool to estimate the pillar loading for most of the geological, geometrical and mining conditions. In this study. finite element technique was used to estimate the state of stress, strain, elastic strain energy and plastic energy, etc. at every point within the pillar. (2) Defining the yield pillar loading zones¬. The proposed method considered the non-uniform stress distribution of yield pillars by dividing the area of the yield pillar into three loading zones, namely core, transition and rib zones. (3) Estimation of stability indicators - an appropriate stability measure was proposed for each loading zone. such as; Core Stability Factor. CSF, Pillar Bump Index, PBI and Rib Instability Index. RIF. A case study of successful and unsuccessful yield pillar application was used to assess the applicability of the proposed method.

Jan 1, 2003

By Victor V. Nazimko

Longwall mining technology without interpanel pillars is feasible from a geomechanical point of view. A set of pillarless longwall layouts are proposed including tailentry pillar recovery, headentry pillar recovery and drivage of a new tailentry, partial headentry pillar recovery and combination mining in which advancing panel entries are used for retreating panels. The following mitigative measures are proposed in order to enhance the stability of entries near the panel: driving crosscuts obliquely to the longwall face line, advance support of entries and crosscuts, localized destressing of the chain pillars by horizontal slotting, and partial stowing of the gobs behind the pillars being recovered. A new technology of recovering barrier pillars on the setup entry side is also proposed. This technology uses the same regular longwall face for interpanel pillars extraction.

Jan 1, 1994

By Jiacheng Wang

The current state of thick seam coal mining methods is illustrated in three typical cases of thick seam longwall mining, each pointing out the outstanding achievements in top-coal caving mining and large cutting height mining in China. At the same time, based on current thick seam mining practices in China, some problems urgently need to be solved. These include improving the recovery ratio of coal reserves, determination of overburden strata pressure, shield support selection, supporting methods for large cross-section in-seam roadways, top coal bulk flow theory, and gas flow and control technology. In addition, the rational production capacity should be studied from both economic and technological perspectives in order to optimize coal recovery and efficiency.

Jan 1, 2011

By S. P. Singh

Rockburst is a sudden manifestation of the release of elastic strain energy stored in the rock. Therefore the tendency of the rock to burst should depend upon its ability to accumulate elastic strain energy. The use of Burst Proneness Index as a simple and reliable indicator to recognize the burst prone situations in the mines has been advocated in this study. The Burst Proneness Index exhibited a strong dependence upon the brittleness, compressional and shear wave velocities and the point load strength index. It was also observed that the Burst Proneness Index increases with the increase in the strain energy per unit volume, c ressive strength and the modulus of rigidity of the rocks. In addition, important causes and the measures to alleviate rockbursts have been outlined in this paper.

Jan 1, 1986

By Peter Cain

Twenty years of research into the design of permanent gateroad support (packs) in coal mines have resulted in two methods of pack design based on engineering principles. The first, the detached block concept, is based on static loading of the support system by an hypothetical detached block. The second, the roof beam tilt concept, is based on the dynamic loading of the support system as the roof beam tilts over the roadway about a pivot point located in the rib-side. The roof beam tilt concept has been used on a number of occasions to design packs in a variety of conditions. However, recent work in the Sydney Coalfield of Cape Breton Island, Nova Scotia, has shown that design criteria based on the roof beam tilt concept in its present state of development are far from universal in application. After a review of published pack performance data, including detailed studies conducted in the UK, France and Canada, it was found that consideration of the mechanical properties of the roof beam produced a design criterion that fitted the available data. Modifications to the design process using the roof beam tilt concept are suggested for use in pack design. The work also revealed that current research in other aspects of coal mine ground control, particularly the areas of powered support design and subsidence prediction, may provide valuable information leading to major advances in this field. Such developments could also extend the application of the roof beam tilt concept to the design of pillar systems.

Jan 1, 1993

By Stephen P. Signer

This paper presents the results of a case study conducted in a two-entry gateroad in a coal mine where excessive roof deformation and bolt loading resulted in failure of many roof supports. The instruments consisted of 16 fully grouted, strain gaged resin bolts, load cells on both full and partially grouted cable bolts, and vertical deflection multipoint extensometers. These instruments were installed on-cycle to measure loading on bolts in an existing support pattern and to determine if cable bolts could be used to improve roof stability. Results showed significant amounts of movement within the bolted zone. In sonic cases, these movements were enough to load the supports past their ultimate strength. Geology appeared to be a significant factor in localized roof degradation; that is, a very weak rock layer in the immediate roof overlain by a very strong rock layer contributed to the development of shear planes. Only one instrumented bolt had a maximum strain of less than 2,000 microstrain, which was the yield point of the steel. The average maximum strain on all bolts was 20.000 microstrain. However, electrical continuity to many gages was lost, and a pattern was noted that would indicate possible bolt failure. Wire mesh and concrete cans installed as secondary support performed very effectively.

Jan 1, 1998

By Thomas L. Hutchinson

The mechanical design of a roof support is basically a matter of a statics and dynamics problem, assuming of course, that the imposed loads and mining conditions are known. Here in the Appalachian coal fields the general conditions are known well enough to allow the majority of the proposed new faces of longwall to be furnished with standard commercially available supports equipped with suitable variants and options. While not trying to negate the primary importance of thoroughly investigating a potential face and the selection of the correct equipment for that face, it still becomes clear that an equally important aspect of the design of an adequate ground control program has in the past too of ten been overlooked, having been overshadowed by the ?endless? selection process of the roof supports proper. The equally important aspect which this paper discusses is the overall design of a mining system, which design incorporates not only the size and capacity of the equipment but the following points as well, namely: Equipment adaptability to mining scheme, Equipment va. human constraints, Operation at the designed levels, and Coordination of operation, maintenance and support design. Unless the coordination of these factors is considered in the design and selection of the equipment, a lopsided and inefficient operation is possible. How can we afford to put an 8-10 million dollar investment up to chance as to whether it will yield optimum results or not?

Jan 1, 1981

By Radoslaw L. Michalowski

The operation of mobile mining equipment near the crest of stockpiles and wastedumps often results in localized slope failures. The Bureau of Mines has developed a computer code based on a rigorous limit plasticity approach which determines the admissible total weight for a concentrated loading near the crest of these otherwise stable structures. The program is based on a three- dimensional analysis and provides an upper bound solution to the load that can be applied to the top of the operating distances for mobile equipment from the slope edge. This presentation will discuss the application of limit plasticity to the development of the local three-dimensional collapse mechanism, and the use of the computer code based on this approach for mining applications.

Jan 1, 1990

By E. Hosca

Alternative tailgate loading conditions due to conventional and conventional/yield pillar combinations were evaluated to define roof loading. In order to isolate different loading situations, the tailgate entry was considered as part of the roof-pillar-floor system, which is controlled largely by the structural integrity of each member. A data bank of case studies was compiled, which contains details of roof and floor lithology, structure, support, and mining data, including any failure modes. The range of loading conditions that any tailgate can be subjected to was identified to form the basis of numerical modeling. Numerical modeling was then conducted on tailgate openings to determine roof, floor, and rib responses, including failure modes to a variety of loading conditions. Trends developed from the numerical modeling were modified using field data to form the basis for support evaluation and application. The effects of support were modeled numerically to determine optimum load capacity and points of application for reducing the potential for entry failure.

Jan 1, 1994

By Gift Makusha

Surface subsidence associated with coal mining activities in the Mpumalanga Province of South Africa changes the natural environment in several ways, and current challenges for mining companies include rehabilitation of the natural environment and the prevention of further degradation. To monitor the spatial and temporal evolution of surface subsidence, traditional fieldbased monitoring approaches such as GPS and spirit leveling are employed at a number of locations. However, the resulting measurements are point-based, and frequent revisitations are necessary to map the evolution of surface subsidence basins over time. To address these limitations, differential interferograms derived from repeat-pass satellite-borne synthetic aperture radar (SAR) systems were tested for their ability to measure and monitor surface deformation. The SAR data was captured by the European ERS-1 and ERS-2 satellite and covered a timeframe between 2008- 09-15 and 2008-09-15. The resulting interferograms revealed several features indicative of surface subsidence. Ground truth data confirmed the presence of a subsidence basin, detected using differential interferometry techniques during the 35-day period between April 12, 2008 and May 17, 2008; a maximum vertical deformation of 3.2 cm (1.3 in) was recorded. Interferometric monitoring revealed an eastward migration of the subsidence basin between June 2, 2008 and September 15, 2008 with an additional 4.7 cm (1.9 in) of subsidence observed. This migration coincides with the advance of the working face of the mine during this period. Finite element modeling will be performed in order to model the rates and evolution of surface subsidence haloes as underground mining advances. These presented results demonstrate the ability of interferometric synthetic aperture radar techniques to measure surface subsidence as well as the monitoring of the evolution of subsidence basins over time. This implies that the technique could be included, together with traditional field-based surveying techniques, in an operational monitoring system. With knowledge on deformation rates and subsidence basin evolution, informed decisions on current and future infrastructure development can be made and remedial actions and prevention strategies can be formulated for the problems associated with environmental degradation.

Jan 1, 2011