Search Documents

By Saeed Zhandi, Behdeen Oraee

"Rock bursts remain an important problem in longwall coal mining. These bursts are due to a sudden and severe failure of rocks from a high stress concentration in deep underground excavations that occur with the instantaneous release of strain energy stored in the rocks. They can potentially cause irrecoverable damage to equipment and personnel, thus accurate rock burst prediction and control is expected to be carried out by the mine design engineer. As a result, this can constitute major challenges for said engineer. In this paper, forensic engineering has been used to evaluate the possibility and extent of rock bursts in deep coal mining. For this purpose, established mining engineering principles, including factors influencing the severity of rock bursts, have been incorporated in the forensic engineering technique. The analyses took place in five steps:• Assessment of regional and local conditions prior to the event• Assessment of conditions after the event• Hypothesize plausible ways in which pre-event conditions can become post-event ones• Search for evidence that either denies or supports various hypotheses• Apply engineering knowledge to relate the various facts and evidence into a cohesive scenario of how the event may have occurred.The paper concludes by demonstrating a method for predicting rock bursts and preventing their reoccurrence. The methodology used in this paper, together with the results obtained, can serve as useful tools for the coal mine design engineer in the primary evaluation of rock burst potential in underground coal mines.INTRODUCTIONA rock burst is defined as the sudden and great failure of rocks due to a high stress concentration in deep underground mines. This phenomenon occurs with the instantaneous release of strain energy that is stored in the rocks, and can cause irrecoverable damages to both equipment and personnel (see Figure 1). Rock bursts pose a hazard owing to their lake of predictability; in fact, research into understanding rock burst mechanics and implementing techniques for their monitoring and prediction has been taking place for over 50 years."

Jan 1, 2015

By Thomas Barczak

Longwall shields provide essential ground control in Iongwall mining, yet a high percentage of shields are operating at less than peak capacity and many at well below the rated support capacity due to defective hydraulic cylinders or malfunctions in other hydraulic components. Leg pressure data are currently collected on state-of¬the-art longwall shields, but typically are not analyzed to evaluate shield performance. The National Institute for Occupational Safety and Health (NIOSH) Shield Hydraulics Inspection and Evaluation of Leg Data (SHIELD) program is a Visual Basic software system that is designed to analyze leg pressure data and identify shields that are not performing to rated specifications. The program analysis is configured to detect the following conditions: (I ) loss of leg pressure, (2) imbalance in leg pressure, (3) low set pressure, (4) low yield pressure, and (5) full extension of the bottom stage. Other performance assessment measures include the percentage of the support capacity utilized (ratio of peak load to yield load), the percent of time that a shield operates at yield load, the ratio of the set load to the yield load, and the amount of support capacity that is lost due to leaking cylinders. Historical record keeping will allow the user to select a particular shield and review the performance record as developed by the program for that shield. In addition to these performance assessment measures, the software will include an animated description of shield hydraulic systems that will describe the operation and significance of each hydraulic component and the impact of component failures on the shield's capability to provide the required roof support. A general overview of the SHIELD program is provided in the paper together with an example analysis of a 2.5-year-old Australian longwall face.

Jan 1, 2002

By H. N. Maleki

Tension-torque relationships were investigated *n a coal mine for bath standard 5/8 in. (16 mm) bolts and a vibrating wire instrumented bolt, using conventional and controlled installation techniques. The instrumented bolts differed from the standard bolts by their head size and hole preparation procedures. The controlled installation technique developed by the U. S. Bureau of Nines (USBN) involved using hardened washers and lubrication in the bolt assembly, and maintaining a minimum thrust level during bolt installations. The object of this study was to determine the tension to torque ratio (lb/ft-lbs; for standard bolts and instrumented bolts for both conventional and controlled installation techniques, and to modify the bolt assembly so that the ratios would be equal for the instrumented and standard bolts for both installation techniques. It was shown that the instrumented bolts installed in faced holes had a similar tension torque ratio td that of standard 5/8 in. (16 mm) bolts installed in unfaced holes for each installation technique, and thus they were representative of other uninstrumentea bolts. This was achieved by evaluating the influence of several factors oh the relationship, including: facing the hale surface, introducing washers and lubrication in the bolt assembly, and applying different levels of thrust at installation due to bolter operator practice. The tension to torque ratio fur conventional bolts was only 21 (lb/ft-lb) for the coal mine, resulting in an installation tension of 4000 lbs (17.8 kg) with the typical installation torque of 150 to 400 ft-lb. This tension level was approximately 50 percent of the required bolt tension, and thus, it was concluded that torque standards are not sufficient to assure adequate bolt tension. .he low tension levels were due to the particular wait hardware in use, operator practice, and bolt fencing.

Jan 1, 1984

By Joao Felipe Costa, Jair C. Koppe, Andre Zingano, Cleber Gomes

"Run-of-mine Brazilian coal has high ash content and low calorific power. Therefore, the coal must be washed to achieve the power plant specifications for burning coal. A large amount of waste results from the coal preparation, and it must be disposed of in waste piles or waste dams, depending on the material size. These waste disposals are the cause of serious environmental problems, not only in the short and medium terms, but mainly in the long term, due to the risk of provoking acid drainage or spontaneous combustion. Waste disposal requirements also demand large areas. Other problems include the pillar and roof stability in abandoned and mined out areas, building of edifices on the old and active mines, and mining under urban areas. To solve these problems simultaneously, backfilling the entries in mined out areas began with two objectives: to understand the mechanical behavior of the filling material and to model the backfilling of room-and-pillar coal mine entries through numerical simulation. Laboratory tests were performed for different filling material (with and without cement) to determine its mechanical properties and failure criteria. Based on this study, it was possible to conclude that the backfill method is a good strategy to improve the ground stability in room-and-pillar coal mines for the long term, especially for weak coal seams, and to reduce the quantity of material on waste piles on the surface.INTRODUCTIONRun-of-mine (ROM) Brazilian coal has high ash content and low calorific power. Therefore, the coal must be washed to achieve the power plant specifications for burning coal. Two types of waste are associated with power plants that bum coal for energy generation: 1) the waste from the coal preparation plant and 2) the ash from the power plant after coal burning.The Brazilian coal ash content in the ROM coal is between 45 and 55%. The clean coal is 20 to 30% ash for 4,500 kcal/kg (18,000 BTU). The coal preparation plant recovery is only about 35%. Santa Catarina State (SC) produces about 7 million tons/year of ROM coal, which results in a total of 4.5 million tons of waste. This is a large amount of waste that must be disposed of in waste piles or waste dams, depending on the material size. The waste and ash content is represented by silicate materials, such as clay and sand, and by sulfide materials, like pyrite and organic sulfur (between 1and5%)."

Jan 1, 2010

By Yanfa Gao

Abstract In order to control and reduce ground subsidence due to coal mining, and to protect building, railway and other surface construction, a new subsidence control method is proposed. Ground subsidence is reduced by grouting bed separations in overlying strata with fine-coal ash. Engineering application tests have been performed for 5 years in Tangshan Coal Mine. Kailuan Group Corporation. China. The technology has been applied to 4 fully mechanized sublevel caving mining faces. Its effect in reducing subsidence has been significant. The technology including grouting engineering design method and ground subsidence prediction theory is introduced in detail. Keywords: overlying strata separation, multi-layer grouting, subsidence control

Jan 1, 2002

By David P. Conover, Jake Bain, Christopher M. Ross

"Highwall mining of thick (up to 100 ft) steeply dipping (20° or more) coal seams provides many challenges, both geotechnically and operationally because seam dips near or in excess of highwall mining machine capabilities are encountered. Maximizing coal recovery while maintaining highwall stability requires innovative techniques with regard to web and barrier pillar layout, depth of penetration, and choice of mining horizon within the seam. Stability of highwall mining slopes, openings, and pillars are typically analyzed using the ARMPS-HWM program, as well as LAMODEL, UDEC, and Slope-W modeling. Highwall stability can be maintained and highwall mining production optimized by applying design criteria in creative ways, including alternating miner penetration depths and initiating mining of thick seams toward the bottom of the seam. Highwall mining of thick, steeply dipping coal requires careful planning and execution, including close cooperation between geotechnical design engineers, the mining company, and the highwall mining contractor. This paper describes the application of creative design techniques to a specific pit arrangement at the Westmoreland Kemmerer Mine, Kemmerer, Wyoming. Highwall mining was accomplished by UGM ADDCAR Systems, LLC, on a contract basis. INTRODUCTION Highwall mining is a technique for attaining additional coal recovery after the economic strip limit is reached in surface mining. It involves remote deployment of a continuous miner in openings beneath the final highwall, with no personnel entry. Many candidate areas for highwall mining have thick and steeply dipping seams. Mining downdip presents challenges related to the maximum pulling capacity of the machine, traction of the cutting head, and material conveying, all of which limit penetration depth. Maximum penetration is greater for flatter slopes and decreases for slopes nearing the threshold of the maximum machine operating angle. Most highwall mining operations are relatively flat with slight undulations within the seam; therefore, the highwall mining pillar design criteria applies fairly equally to the entire mining area. However, in steeply dipping deposits, design criteria based on higher overburden loads at the far end of the penetration are excessively conservative for the shallower portions of the openings near the highwall."

Jan 1, 2017

By Vince Caggiano

The newly developed Hilti OneStep roof bolt combines the standard 5-step anchoring process (i.e. drilling, transfer of drill steel, insertion of resin, insertion of rod and tightening) into one easy operation. It also replaces 4 items (drill head and steel, adhesive cartridge and anchor) for simplified material management. This paper describes its history of development, and bolt, bolt drilling and bolt resin specifications, experimental test results in Germany where it achieved a reduction of 36-42% in roof bolt cycle time and 25-30% improvement in gateroad development rate. In the U.S. coal mines, a time study showed that OneStep can save approximately 50 seconds in installation time per bolt.

Jan 1, 2005

By Peter Zhang

"Room-and-pillar mining with pillar recovery has historically been associated with more than 25% of all ground-fall fatalities in the underground coal mines of the United States. The risk of ground falls during pillar recovery increases in multiple-seam mining conditions. The hazards associated with pillar recovery in multiple-seam mining include roof cutters, roof falls, rib rolls, coal outbursts, and floor heave. When pillar recovery is planned in multiple seams, it is critical to properly design the mining sequence and panel layout to minimize potential seam interaction. This paper addresses geotechnical considerations for concurrent pillar recovery in two coal seams with 70 ft of interburden under about 1,000 ft of depth of cover.The study finds that, for interburden thickness of 70 ft, the multiple seam mining influence zone in the lower seam is directly under the barrier pillar within about 100 ft from the gob edge of the upper seam. The peak stress in the interburden transfers down at an angle of approximately 20° away from the gob, and the entries and crosscuts in the influence zone are subjected to elevated stress during development and retreat. The study also suggests that, for full pillar recovery in close distance multiple seam scenarios, it is optimal to superimpose the gobs in both seams, but it is not necessary to superimpose the pillars. If the entries and / or crosscuts in the lower seam are developed outside the gob line of the upper seam, additional roof and rib support needs to be considered to account for the elevated stress in the multiple seam influence zone. INTRODUCTION Room-and-pillar mining accounted for about 40% of underground coal production in the United States in 2016. Pillar recovery, practiced in about one-third of the room-and-pillar mines, represents about 10% of the coal mined underground, yet it has historically been associated with more than 25% of all ground fall fatalities (Mark, Chase, and Pappas, 2003). In some U.S. coal fields, particularly central Appalachia, many coal mines are operating under geological conditions with multiple coal seams. The risk of ground falls during pillar recovery increases under multiple-seam mining conditions. The hazards of pillar recovery associated with multiple-seam mining include roof cutters, roof falls, rib rolls, coal outbursts, and floor heave (Mark and Tuchman, 2007; NIOSH, 2010b). Pillar retreating creates abutment pressure, not only in the currently mined seam, but also in the overlying or underlying seams. Multiple-seam interactions become more pronounced as overburden depth increases and interburden thickness decreases. To safely recover the pillars in multiple seams, it is critical to properly plan the mining sequence and panel layout to minimize potential multiple-seam interaction."

Jan 1, 2017

By William Kendall

INTRODUCTION Stillwater Mining Company, with its two underground, hard rock mines in South Central Montana, is the largest primary producer of palladium and platinum in the Western Hemisphere. Platinum Group Metals (PGMs) are mined from a specific zone within the Stillwater Complex, a layered mafic/ultramafic igneous intrusion, named as the J-M Reef. Over much of the J-M Reef, the economically minable, mineralized horizon is contained at typical horizontal widths of 6.5 ft to 8 ft wide. This feature of narrow mining widths has made it challenging to safely and effectively mine these areas of the J-M Reef using mechanized cut and fill and sublevel sill development mining methods. Mechanization of most or all of the steps of the mining process is important to Stillwater in the continuous pursuit of high standards in safety and health. Mechanized bolting within the J-M Reef ore production headings is an important piece of reaching these objectives. In general, metal/non-metal mining requires varied mining techniques, as compared to more traditional bedded mineral/resource deposits. Narrow vein mining is a selective mining technique that generates a minimal amount of waste material while obtaining the more valuable ore deposits. Drilling and bolting in narrow vein mining has traditionally been performed with air-powered, hand-held ?jackleg? equipment because mechanized equipment is, typically, too large for the selective narrow vein techniques. In addition, traditional hand-held pneumatic equipment provides significant flexibility for small-opening, narrow-vein developments, reducing waste rock handling and improving ore recovery management. The hand-held equipment is also relatively inexpensive to purchase. Due to its simplicity, it is also relatively easy to train operators to use hand-held equipment. Hand-held equipment has been routinely used to safely install ground support and to develop production faces in hard rock mines for many years. Although it is effective, the hand-held equipment requires operator exposure to certain inherent hazardous conditions in the active face/development mine areas. These include falling rock, tripping hazards, bending/twisting/lifting hazards, high noise levels, and chemical fumes from the hammer exhaust. Based on health and safety statistics from the Stillwater mines, operation of the rotary-percussive hand-held equipment adversely affects the long-term health of the operator?continual jackleg operation frequently results in long term damage to hearing, shoulders, arm and wrist joints, and back injuries. This reduces the quality of life for the operator and also results in higher personnel turnover rates for the mining company.

Jan 1, 2014

By Alan Campoli

The Eclipse System was developed by Minova USA Inc. formerly Fosroc Inc. to improve the performance of 5/8-inch deformed rebar fully grouted into a one inch borehole. An 1/8-inch offset bolt head combined with specially formulated Eclipse Lokset resin cartridge results in reduced gloving and increased mixing efficiency. The benefits of the Eclipse System have been demonstrated, under the supervision of MSHA, in Kentucky, West Virginia and Illinois coal mines in partnership with Excel Mining Systems, a leading roof bolt manufacturer. Over 100,000 units have been installed to date. Eclipse system bolts exposed during overcast construction at the Panther Mine of Cumberland Resources displayed an extremely well mixed, uniform resin anchorage over the entire bolt length.

Jan 1, 2003

By David Gearhart, Peter Zhang, Gabriel Esterhuizen

"Researchers from the National Institute for Safety and Health (NIOSH) installed instruments in the track entry and in the pillars of a northern West Virginia longwall coal mine between two planned panels for the purpose of monitoring the behavior of the ground. The instruments included four cable bolt load cells to measure the change in gateroad loading, six borehole pressure cells to measure the loading in the pillars, three six-channel roof extensometers to measure roof sag, four convergence measurements on the cribs to measure the crib loading, and a multipoint borehole extensometer to measure the pillar expansion. The instrumentation was all connected through two multiplexers to a single Campbell Scientific permissible datalogger located about 350 feet outby the instruments. The goal of the project was to record all of the measurements as both longwall faces passed the site of the instrumentation and to use the data to calibrate numerical models.This report describes the recording of all of the measurements taken as the first panel approached and then passed the instrumentation site. This study provided valuable data related to the ground response and support performance that will be used to improve safety in longwall gateroads.INTRODUCTIONA longwall mine in northern West Virginia was selected as a second study site for an ongoing research project into gateroad layout and support design. The area was affected by a transition from limestone to sandstone in the roof. The entries were 16 feet wide, and the height was approximately 80 inches. The layout for the longwall panels was 1,170 feet wide by 4,000 feet long. The panel configuration was right-handed, and a three-entry gateroad was used between panels. The pillars next to the headgate were 137.5 feet by 115 feet center-to-center, and the pillars next to the tailgate were 275 feet by 100 feet center-to-center, with the crosscuts at 60 degrees. The width of the gateroad was a total of 215 feet."

Jan 1, 2018

By T. J. McMahon

This Bureau of Mines study describes the development of a large-scale, three-dimensional, finite-element model of a deep-vein Coeur d?Alene District mine. The three-dimensional model was prepared from combined digitized mine maps and generated levels that may also be analyzed as independent two-dimensional models. A comparison of the stress changes and displacements was made following a simulated vein excavation in both the three-dimensional and two-dimensional models. A one-cut excavation was simulated with the two-dimensional model and a multiple-cut excavation was simulated with the three-dimensional model. The compared results from the two analyses are discussed in terms of the inherent differences between the models.

Jan 1, 1989

By Bruce W. King, David A. Newman

"Underground mines have always been an integral part of the limestone industry. However, beginning in the 1990s, the number of underground limestone mines has increased for many reasons including• Stripping ratios at surface quarries have become uneconomic.• Existing surface quarries have reached the mineral boundaries, and the remaining stone reserves are underground.• Surface access to the entirety of the limestone reserve is limited by development or infrastructure.• The once-rural setting of the surface quarry is now surrounded by subdivisions and development. An underground mine is less intrusive and takes the mining operation out of the public eye.• For larger markets, an underground mine enables year-round production without the sequence of overburden stripping in the winter to expose mineable stone for summer production. This is common at many surface quarries.Multiple-level operations are a natural extension of the decision to mine underground. Most limestone reserves, for example, the Tyrone-Oregon-Camp Nelson, Hermitage-CartersLebanon- Ridley, and Salem Limestones, are sufficiently thick to accommodate multiple levels. Multiple-level mines should be planned by considering each level separately and then integrating the individual levels into a larger mine plan. Failure to plan all the levels of a multiple-level mine in concert can result in ground control (back, pillar, floor, and inter-level sill pillar) problems attributable to stress transfer and interaction between the levels or the necessity to leave a thicker sill pillar between adjacent levels.Multiple-level mine planning begins with geology. Once the upper level back horizon is identified, the geology, rock strength, and physical properties in each level are used to• identify the optimal back horizon• quantify whether back support is required and, if so, the type, spacing, and length of the back support• determine the pillar centers• determine the total mining height, including floor shots"

Jan 1, 2016

By E. Bane Kroeger

For many years, researchers around the world have been investigating coal pillar stability. Many have focused on trying to optimize the size of the pillars by examining stable and failed pillars in underground coal mines. For mines that are already in operation or companies that are opening a new mine adjacent to an existing mine where the pillar dimensions and stability can easily be determined, this is the preferred technique. However, when a new mine is planned for an area where there has been relatively little mining, then samples of the coal need to be drilled and tested for strength. Because of the fractured nature of coal, this lab testing is often problematic and may often yield poor results because of the limited size and number of samples that can be obtained from the core. To remedy this problem, research was conducted in the labs at SIUC to determine if improvements could be made when optimizing the size of pillars for underground coal mining in Illinois. Through a greater understanding of the relationship between dimensions and strengths of coal samples tested in the lab, it was hoped the in situ strength of coal pillars could be determined with greater accuracy. This could allow the extraction ratio to be increased and more of the coal resources in Illinois recovered without impacting the safety of the mine workers. Many different agencies around the world have published recommended minimum numbers of samples for strength determination based on the size of the coal samples. For two inch cubes, uniaxial testing of at least seven samples is recommended and this minimum number decreases to four when testing four inch cubes. However, the laboratory testing of coal from two seams thus far has suggested this number should be almost doubled to accurately determine the coal strength. Testing also showed there is a pronounced decrease in the variation in the strength of the samples tested as the dimensions of the sample were increased. From the testing results thus far, it is recommended that a sample size versus strength curve be constructed for every coal seam for Illinois. Creating such a curve will better determine both the minimum number of samples and minimum sample dimensions for that seam or region of a particular scam. A second set of tests were conducted in the laboratory to determine the increase in strength with reduction in height for samples with the same width and length. In Illinois, typical pillar dimensions are 40 to 80 feet (12.2 to 24.4 m) wide and long, with coal thickness varying from about 4 to 9 feet (1.22 to 2.74 m). This provides width/height ratios ranging from 4.5 to 17.5. Coal samples having width/height ratios ranging from 0.5 to 13 have been tested thus far. As with most pillar design formulae, the strength of the Murphysboro coal versus width/height ratio was linear and closely matched shape factors published by other researchers. The laboratory testing thus far has identified three factors that affect the strength of laboratory samples, the number of discontinuities, the angles of critical discontinuities, and the shape of the samples. The factor that probably had the most pronounced effect on the strength of the coal samples was the angle of critical discontinuities. This testing has confirmed that there is still a gap that needs to be bridged between the strength obtained from laboratory testing and the in situ coal strength predicted.

Jan 1, 2004

By Peter Zhang, Todd Minoski, Mark Van Dyke, Daniel W. H. Su

"This paper presents the results of a 2017 study conducted by the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Mining Research Division (PMRD), to evaluate the effects of longwall-induced subsurface deformations within a longwall abutment pillar under deep cover. The 2017 study was conducted in a southwestern Pennsylvania coal mine, which extracts 1,500-foot-wide longwall panels under 1,185 feet of cover. One 650-foot-deep, in-place inclinometer monitoring well was drilled and installed over a 150-foot by 275-foot center abutment pillar. In addition to the monitoring well, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the 1,500-foot-wide longwall panel on the south side of the abutment pillar was being mined.Prior to the first longwall excavation, a number of simulations using FLAC3D™ (Itasca, 2017) were conducted to estimate surface subsidence, increases in underground coal pillar pressure, and subsurface horizontal displacements in the monitoring well. Comparisons of the pre-mining FLAC3D simulation results and the surface, subsurface, and underground instrumentation results show that the measured in-place inclinometer casing deformations are in reasonable agreement with those predicted by the 3D finite difference models. The measured surface subsidence and pillar pressure are in excellent agreement with those predicted by the 3D models. Results from this 2017 research clearly indicate that, under deep cover, the measured horizontal displacements within the abutment pillar are approximately one order of magnitude smaller than those measured in a 2014 study under medium cover.INTRODUCTIONDue to a recent shale gas boom, approximately 1,400 unconventional shale gas wells have been drilled through active and future coal reserves in Pennsylvania, West Virginia, and Ohio over the past 15 years. These shale gas wells have penetrated many coal seams, such as the Sewickley, Pittsburgh, Upper Freeport, and Kittanning seams. These unconventional gas wells, whether tapped into the Marcellus or Utica formations, contain very high gas pressure. Strata deformations associated with longwall and other high extraction techniques could induce high stresses and deformations in the shale gas well casings. This could seriously compromise the mechanical integrity of the production, intermediate, and coal protection casings (Figure 1). Damaged well casings could potentially introduce high-pressure, explosive gas into underground mine workings, particularly during an extended well shut-in period, which could seriously jeopardize underground miners’ safety and health."

Jan 1, 2018

By David Bigby, Tim Ross, David Conover

"Extensive arrays of telltale roof monitoring instruments were recently installed in a Mexican copper mine and a large underground mined storage facility in the eastern U.S. The data were used to evaluate roof stability during development and retreat mining and after installation of supplemental supports. Both manual-reading and automated systems were employed and consisted of up to 64 instruments. This paper will discuss the practical issues involved with installation and monitoring, including reliability and maintenance. Examples will be given for telltale response in relation to known events affecting roof stability, including nearby pillar extraction roof caving, installation of supplemental cable bolts, and separation of the immediate roof layer. The strategy for processing the large quantity of data, presenting the data for review, monitoring the system remotely, and identifying and reporting critical events will be described.INTRODUCTIONTelltales have been used for many years with many varied applications. They are relatively inexpensive, easy to install and interpret, robust, and adaptable. The term ""telltale"" generally denotes a strata extensometer that incorporates a visual indication (and warning) of strata movement. The most common dual-height telltale (Figure 1) was developed by British Coal in the early 1990s as roof bolting was replacing steel arch support (Bigby, 2001). Dual-height telltales provide immediately visible measurements, distinguish between movements above and below the bolted height, and are an established means for providing preemptive warnings of roof falls.Many improvements and modifications on the basic design have been developed to adapt to different mining conditions. For example, triple-height telltales are commonly used where roof bolts of different lengths are installed. The standard manuallyread telltales are limited by the difficulty of obtaining frequent, consistent, and accurate readings, especially in high openings. The instruments may also be located in unstable or inaccessible areas. Consequently, an intrinsically safe electronic telltale system was developed that combines high accuracy and both local and remote reading options. The system supports a network of up to 100 dualheight telltales on each of four separate branches. The instruments are connected with a two-conductor cable and can be read both underground, using a portable readout, and on a surface computer (Figure 2). The automated system still provides the visual warning indication underground."

Jan 1, 2010

By R. Kaund

"Quantifying the rockburst consequence is of critical importance to reduce the hazards with preventative measures in underground mines and deep tunnels. Contours of energy components within a pillar model are plotted at different rockmass damage stages, and plastic strain work and released energy are proposed as indicators of rockmass damage consequence. One pillar model under different loading stiffness is simulated to assess indicators of pillar burst and the resulting damages. The results show the rockmass damage under soft loading stiffness has larger magnitude of plastic strain work and released energy than that which is under stiff loading stiffness, indicating the rockburst consequence can be quantified with plastic strain work and released energy in numerical models. With the quantified rockburst consequence, preventative measures can be taken to avoid severe hazards to mine safety.INTRODUCTIONWith the increasing demand of mineral resources and depletion of near-surface ores, the depths of underground mines have made the mining activities one of mankind’s most dangerous types of work (Ortlepp, 2005). The Mine Safety and Health Administration (MSHA) defines rockburst as “a sudden and violent failure of overstressed rock resulting in the instantaneous release of large amounts of accumulated energy.”The types of rockburst can be classified into three types: (1) strain burst, (2) pillar burst, and (3) fault slip (Müller, 1991). Strain burst is the most common type of unstable rock failure in underground openings, where the intensity and scale are usually smaller than pillar burst and fault slip (White and Whyatt, 1999; White, Williams and Whyatt, 2002; Ortlepp, 2005). The cause of strain burst can range from shattering of rock under high stress concentration to buckling of discontinuities parallel to underground openings. The occurrence of pillar burst also depends on the stress and discontinuity conditions in the rockmass, but pillar burst usually involves the sudden loss of strength in the core or foundation of a pillar (Whyatt and Blake, 2002; Kias and Ozbay, 2013; Khademian et al., 2016). Fault slip or slip burst can be either slip along pre-existing discontinuities or shear failure in the rockmass, when the shear stress is larger than shear strength in the fault (Rice, 1983; White and Whyatt, 1999; Sainoki and Mitri, 2014). The consequence of fault slip can vary from very small rockmass damage to consequential rockmass damage, but large seismic magnitude does not always result in large rockmass damage (White and Whyatt, 1999; Whyatt and Blake, 2002)."

Jan 1, 2018

By J. D. Cole

In order to reduce the number of longwall face moves and to increase the rate of gateroad construction, super longwall panels, 1000 feet wide and 12000 to 14000 feet long, are planned for Wolf Creek Collieries No. 4 mine. The development of the longwall panels at the mine has evolved from 5-entry, to 4-entry, to 3-entry systems. A three-entry system including pillar size and entry supporting method for the super longwall panels was designed for long-term stability. The design procedures included field observation and studies, laboratory properties tests, in-situ stress measurement, and computer analysis. Three pillar design methods consisting of PILLAR, ALPS, and the Wilson Method, and one entry supporting method, ROOFBOLT, were adopted in this study. The procedures, methods, and results are discussed in detail.

Jan 1, 1990

By Anthony Spearing

There are approximately 68 million rockbolts installed annually in underground coal mines in the USA (Tadolini and Mazzoni, 2006). The most utilized is the passive fully grouted resin rebar bolt, which constitutes almost 90% of the primary support in US underground coal mines. Resin-grouted rockbolts are a very effective and safe support, but their performance still needs to be further optimized and improved. This paper investigates their performance and suggests operating conditions to optimize the performance of resin-grouted rockbolts. In addition, this paper discusses a small-scale test that can also be used to evaluate the performance of rockbolts that is quicker, easier, and less costly than short encapsulation tests.

Jan 1, 2014

By Joseph Hirschi, Naga S. Y. Tirumalaraju, Aditya Mishra, Anthony (Sam) J. S. Spearing

"Primary roof support in underground coal mines in the USA consists mostly of fully grouted passive rebar or grouted (partially or fully) tensioned rebar. Research conducted at two room-and pillar coal mines in the Illinois Basin and one longwall mine in Colorado monitored the performance of these passive and active rock bolts under similar geologic and mining conditions and found no significant initial loads in either passive or active rock bolts (Spearing et al., 2011). Active rock bolts showed significant loss of initial pre-load, although the exact reasons for this were not fully investigated. Subsequent laboratory testing has also shown that in weak rock, resin creep occurs, caused by slippage of the mechanical key between resin column and rock interface. These creep tests were studied in the laboratory in an effort to quantifythis phenomenon.INTRODUCTIONResin-grouted rock bolts are the first and main line of defense to counter roof and rib falls in underground coal mines of the United States. Rock bolts are categorized as active or passive. Active bolts are tensioned during installation whilst no (or limited) tension is applied to passive bolts, which need subsequent strata movement to generate reactive loads. During installation of passive bolts, some reactive pre-load may be generated by a significant up-thrust from the rock bolter boom.The selection of active or passive bolts is critical and is mostly dependent on the conditions and properties of the immediate roof (Unrug, 2009). This decision is frequently made based on personal experience, bias, and most recently cost. Active bolts are generally used in cases of highly laminated roof rock. When active bolts are tensioned, they develop compressive forces between these layers forming a beam, which helps to stabilize weak individual layers thereby increasing frictional forces between layers and decreasing effects of horizontal stresses. The fully grouted tensioned rebar system is high in stiffness as compared to mechanical bolts and provides higher surface area of contact along the length of the bolt due to the grout, which permits it to develop a strong anchorage mechanism."

Jan 1, 2015