Search Documents

By John Kucish

Roof bolting in the Pittsburgh Coalbed takes many forms today: coupled partially grouted bolts, fully grouted rebar, passive cable bolts, tensioned cable bolts, and torque tension rebar. The Federal No. 2 Mine of Peabody Energy has recently made a significant advance in longwall headgate primary roof support, with the change fiom an 8 ft long coupled partially grouted bolt to a 6 ft long torque tension system. The coupled partially grouted bolt consists of a 4 ft long 0.804 in diameter rolled deformation bar thread coupled to a smooth 718 in headed bar. The coupled partially grouted bolt is anchored into a 1 318 in borehole with 4 ft of high speed resin. The 718 in diameter smooth bar is tensioned by rotation into the treaded coupler, upon setting of the resin, compressing the immediate roof. The change was initially driven by occasional failure of the coupled partially grouted bolt at the threaded coupler, due to lateral movement caused by horizontal stress. A fully grouted % in diameter torque tension bolt, in a 1 in borehole, was proposed as a cost effective primary bolting for the high horizontal stress conditions. The upper 2 112 ft of the rebar is anchored in fast set, medium viscosity resin and the bottom 3 K ft is anchored in slow set, special low insertion force resin. The lower end of the rebar is threaded with a nut that permits the counter clockwise spinning of the bolt to mix the resin, at maximum rotational torque. Upon setting of the high speed top resin, the nut is spun clockwise to tighten the nut against a metal dome plate. The plate is forced against the roof to compress the immediate roof, A complete headgate entry has been successfully supported with the torque tension system. The mining of the adjacent longwall panel was completed in September 2004. The torque tension system provided a 25% savings over the previously employed coupled partially grouted bolt system.

Jan 1, 2005

By Thomas Barczak

Longwall mines typically use some form of standing support for secondary roof support in longwall tailgate entries. Although there have been several new support products developed for this application, there remains no universal design criteria to optimize the application of these support technologies. The requirement for optimization and proper support selection is to understand the degree of control that the support has on the ground behavior. The ground reaction curve and numerical modeling was used to evaluate the impact of standing support on ground behavior. LaModel was used to evaluate the impact of standing support on main roof and floor behavior and pillar yielding. The conclusion drawn from this study was that standing supports do not have sufficient capacity to control main roof or floor loading or prevent the resulting convergence of the tailgate entry. However, it is imperative that this "uncontrollable convergence" be considered in the support design to prevent premature failure of the support. A FLAC model was used to evaluate the near-seam roof and floor behavior in conjunction with the global vertical and horizontal stresses. The model suggests that standing roof supports can have some impact on the ground behavior as the elastic response of the rock is exceeded and rock structure deteriorates from the stress concentrations that develop around the tailgate opening. During this phase, the capacity and stiffhess of the standing support can be critical to the stability of the opening, as eventually the rock mass will be transformed into a partially detached structure whose weight must be supported by the standing support. This work is part of a ground control program of research at the National Institute for Occupational Safety and Health (NIOSH) aimed at improving mine safety by reducing roof fall injuries and fatalities.

Jan 1, 2005

By Kot F. v. Unrug

In spite of the extensive research and accumulated experience from mining operations, an appropriate pillar design remains an open issue. Due to the shrinking reserve base, present mining operations move to more challenging conditions. There are usually thinner seams and geologic conditions are often unfavorable. For instance, mine roof and floor are weak or deteriorate rapidly when exposed to moisture fluctuations in mine atmosphere. It is common that pillars of current operations are more- squat than several decades ago when the bulk of pillar research have been carried out in thicker seams. The methods of pillars calculations were developed regionally (in particular countries) to suit design needs for the most important seams, from which the majority of coal production was coming (e.g. Pittsburg or Pond Creek seams in the eastern of US). Most of the pillar formulae use similar approach by assigning weights (using constants) to the influence of coal (seam) strength and pillar widthheight ratio on its final strength. That mechanistic approach has sound theoretical base and good data supporting its validity. However, what seems to be missing is a qualification system of the mine conditions, which are outside of the data base or do not comply with the theoretical model applied in pillar strength formulae. This paper attempts to address that issue in two major categories, first when only a drill core data are available, and second during the mine development observations can be made directly on a coal seam. The composition of a coal seam is also addressed, (which often changes rapidly across the reserve), and discussed its influence on pillar's structural performance. In summary a set of practical design rules is presented.

Jan 1, 2005

By Deren Zhu

The principle of roof control in longwall mining is to control main roof fractures so as to reduce roof weighting, plus reasonable and effective design of supports to reduce the convergence and premature caving of the immediate roof. This paper introduces a comprehensive test for better roof control based on the geological conditions of coal seam No. 16 in Zaozhuan Colliery, China.

Jan 1, 1990

By Francis Kendorski

One of the most dangerous events in underground coal mining is unexpectedly encountering water inrushes from undetected abandoned mines in the same seam. The surest and most confident method is probe drilling either from the mine or from the surface. However, drilling is expensive and may even miss the suspected mine voids entirely by drilling through pillars. Many operators rely upon one or more of several remote sensing techniques for detecting mine voids. However, mine "voids" often are not air- or water-filled open cavities, but are collapsed, rubble-filled chimneyed columns in the strata. Geophysical techniques, such as seismic reflection and refraction, electrical resistivity, magnetics, ground-penetrating radar, and others, often assume a continuous or fractured rock mass that has varying properties which provide the signatures that allow discrimination of one strata from another, or of strata from voids. However, a rubble-filled cavity has rock block-to-rock block contact throughout its volume and can still respond as a continuous rock mass with the rock blocks allowing signal transmission or mass detection, rather than a void space. Hydraulically, a rubble-filled cavity is essentially as transmissive to water as an open mine void. Thus, the problem of detecting a mine void with confidence is significantly compounded.

Jan 1, 2004

By L. Mahony

This paper describes the design, construction and commissioning testing program for a laboratory facility at the School of Mining Engineering, UNSW, Australia, aimed at evaluating reinforcement tendon performance when subjected to shear loading. The project has been financially supported through the coal industry ACARP research initiative. The single failure plane design adopted in the test rig has been successful in allowing shear loading to be directly applied to fully installed (and where relevant, pre-tensioned) rock bolts. Initial results are extremely encouraging, and illustrate a significant axial component of load development as shearing takes place - particular in lower strength, softer material types. The paper also outlines future plans for use of this facility.

Jan 1, 2005

By Tom Vandergritft

With advances in system design driving higher productivity, safety, and coal recovery, highwall mining is becoming an attractive option for extending reserve life at surface mines. Typically, highwall mining is performed by contract, with the system owner charging the mining company on a per ton basis, plus a mobilization fee. For this arrangement to benefit both parties, geotechnical planning is required to minimize risk to highwall mining personnel and equipment, while maximizing coal recovery. This paper discusses how highwall mining has been successfully implemented at a large surface coal mine in Colorado, including design procedures, operational factors, and productivity. The operation includes an area where four seams are mined in succession from the lowermost upward, requiring careful attention to seam interaction issues.

Jan 1, 2005

By Quanxi Wang

This paper presents a new stability mapping system which tightly integrates structural and geologic mapping with geo- mechanical stress analysis for use in support design and mine plan- ning. The structural and geologic input can include such local characteristics as: rock strength, layer thickness, faults, stream val- ley effects, etc. The geo-mechanical stress inputs can include overburden stress, multiple-seam stresses, abutment stresses, etc. The mapping system utilizes the popular AutoCAD/SurvCADD platform as a foundation for inputting the geologic characteristics, and then integrates the boundary-element program LaModel for determining the geo-mechanical stress influences. Additional func- tionality in the system allows the user to transform each individual geologic or stress factor into an individual rating and then the user can apply various weighting functions to the individual factors to generate an overall stability index map for the mine property. A sample case study is included in the paper to demonstrate the basic concepts, procedures and utility of the stability mapping system.

Jan 1, 2005

By Dion Pastars

Resin based grouts are the main form of rock bolt anchorage in the underground coal industry in Australia and New Zealand. To be effective, the system requires the mixing of the catalyst and mastic components of the resin, as well as shredding of the laminate cartridge that contains the resin. An unknown measure is the load transfer characteristics of a bolt where the resin is well mixed but remains encased in the cartridge (gloved). Laboratory and in situ field investigations have been undertaken to quantify the performance loss due to mixed gloved bolts. This work showed repeatable results, indicating serious performance loss of the gloved and mixed system, with load transfer approximately 10- 15% of a non-gloved system (MacGregor, 2004). The in situ testing has demonstrated the relationship between the adhesion qualities of the resin and the mechanical interlock generated by radial confinement with progressively increasing tensile load. Effective load transfer is defined by the ability of the system to sustain shear stress on the bolt hole wall.

Jan 1, 2005

By J. F. T. Agapito

Overcore measurements at the North Fork Valley (NFV) coal mines in western Colorado have shown that horizontal stresses are highly anisotropic. Measurements have been made in four mines at various depths. In many measurements, the maximum horizontal stress is three to four times higher than the minor horizontal stress. At the West Elk Mine, maximum and minimum horizontal stresses of 24 MPa and 6 MPa, respectively, have been measured at depths of 640 meters (m). Under highly anisotropic stress conditions, ground control problems associated with both high and low horizontal stresses can develop. While high horizontal stresses can produce cutter failures and floor heave, low horizontal stresses can allow block fallouts. This paper summarizes the horizontal stress measurements in NFV mines and, in particular, in the West Elk Mine where their role in roof fall and floor heave failures is discussed. This experience has led to an improved use of ground support and safer mining operations at depths of 640 to 700 m.

Jan 1, 2005

By Kresho Galovich

Quinsam Coal Mine located in Vancouver Island, BC, Canada is mining the No. 1 coal seam at the 2 North/3 North mine and the No. 3 coal seam at 4 South Mine. This paper describes its geology and structure, mining and processing, development and depillaring practices as well as methods of roof supports under various geological conditions.

Jan 1, 2005

The effects of corrosion upon the load bearing capacity and ultimate tensile strength of galvanised friction bolts were determined. Corrosion rates were measured by overcoring of the reinforcement elements in situ. Overcoring was achieved at several sites using a specifically designed overcoring drill rig. This rig has the capacity to drill up to 3.0m long 140- diameter core in any orientation and up to a collar height of 7.0m. The recovered core and friction bolt elements were pull tested in the rock mechanics laboratory at the WA School of Mines (WASM) in order to determine their load-displacement characteristics for various embedment lengths. The friction bolt elements were then analysed for rates of corrosion and tested for their ultimate tensile strength. Relationships were formed between these data and the environmental conditions to which the friction bolts were exposed, in order to determine the major factors affecting the corrosion process and how they affect bolt performance.

Jan 1, 2005

By Graham Daws

The introduction of UK rock bolting technology has been applied in many large underground coal mines around the world. This paper explains the methods that have been applied for its successful introduction and discusses several case studies. It does not give fine detail but is intended to allow decision makers to gain a basic understanding of the method used to introduce rock bolting to a mine.

Jan 1, 2011

By D. Bigby

The current British Standard on rock reinforcement components used in coal mining (BS7861:1996) employs the axial double embedment tensile PET) test to determine the main system load transfer performance criteria, in terms of bond strength and stiffbess. This test involves measurement of load/displacement characteristics of a tendon fully grouted into internally threaded thick-walled steel tubes. Part 1 of the Standard covers rock bolting systems and Part 2 covers birdcaged cable bolting systems. Both parts are highly prescriptive, defining a specific design of bar (AT) and cable bolt (birdcaged). In 2000, it was agreed by the UK Rockbolt Research Liaison Committee that Part 1 of the Standard should be revised to allow further industry innovation of bolts and resins. Amongst other aspects, it was recognised that the double embedment test was limited by its inability to examine load transfer between the bolt and the host rock and the UK Health and Safety Executive commissioned an RMT research project to develop a new test to replace the DET test. The new test, the Laboratory Short Encapsulation Pull (LSEP) test has now been incorporated into a draft revision of BS7861 Part1 which has been issued for industry wide consultation. In 2003, it was agreed to begin revision of Part 2 of the Standard to encompass the many types of long tendon reinforcement which were, by then, being used in the UK coal mining industry. These included flexible bolts, deformed strands and tensionable systems encapsulated with resin, cementitious grout and combinations of the two. A second RMT research project was funded by the HSE to examine adapting the Laboratory Short Encapsulation Pull Test for the revised long tendon Standard. This project is nearing completion and a revised Part 2 of the Standard is being drafted. This paper presents some of the results of the two research projects, describes the laboratory tests and acceptance criteria developed and discusses the implications of the research on improving the understanding of reinforcement performance and its characterisation. In particular it shows how the new test can reveal very different load transfer characteristics to the double embedment test, as it takes the load transfer at the holefrock wall into account.

Jan 1, 2005

By Jian Yong Chen

The results of a laboratory investigation of pullout tests conducted on grouted, plain cable bolts are reported. The main purpose of the study is to determine experimentally the shear bond stiffiess of cement grouted and resin grouted cable bolt systems, which is an important input parameter for numerical modeling of cable bolt support. Three nominal embedment lengths of 152mm (6 inch), 203mm (8 inch) and 254mm (10 inch) were used and two types of grout namely cement and Anchortite resin were used. Two water- to-cement ratios of 0.3 and 0.4 were employed for the cement grout. The concepts of effective shear stress and effective shear stiffiess are explained and adopted to calculate the shear bond strength and the elastic shear bond stiffiess per unit length. A comparison of results with previous research is presented to reveal the effect of water-to-cement ratio and embedment length on the shear bond characteristics of grouted cable bolts.

Jan 1, 2005

By Wenjun Ju

It's very important to determine the limitation of bed separation in entry roof in order to predict roofs stability and take some necessary precautions. Based on numerical modeling and monitoring in the field, the new concept of Limitation of Roof Layer Separation (LRLS) and its method of determination LRLS is given in this paper

Jan 1, 2001

By Shuangsuo Yang

Coal ribs can roughly be divided into three types: (1) roof and floor rocks are similar to ribs, (2) roof and floor rocks are stronger than ribs, and (3) roof and floor rocks are weaker than ribs. Different types of roof/floor and ribs will exhibit different types of ground pressure around an entry. Most coal mines belong to the 2" type with ribs fractured or even broken. In this case the mine ground pressure depends on the occurrence and development of deformation and fracture of the ribs. If it's not properly controlled, the following deteriorating process will follow: the roof bent downward > the ribs squeezed and broken > rib sloughing and collapse > rib support to the roof reduced > the roof bent downward further > the ribs broken further. In this paper rib instability is divided into four types: compression/shear sliding rib fall, gravity sliding rib fall, cross arch rib fall, and cleavage rib fall. Since failure in thin walls is largely of tension type whereas that of thick walls by compression or shear, a concept is proposed here to utilize a thick bolted rib to stabilize entry ribs, i.e. the thickness to height ratio of the thick bolted ribs

Jan 1, 2005

By Yundong Ma

In this paper the dynamic process of rock deformation and failure in the roadways of the #9 coal seam, Wuhushan Coal Mine by was simulated using the software "Rock Failure Process Analysis System (REPA)" [I]. Based on the simulation results, this paper analyzes the failure process, characteristics and weighting of the overburden as the longwall retreat mining proceeds. The roadway's behavior including deformation characteristics, failure mechanisms, stress distribution in the surrounding rocks and the effects of various support systems on roadway stability were analyzed and studied. While simulating the rock failure process with REPA, the model stresses can be obtained through two approaches: (1) the stress is reflected by the grayscale of pictures in the model failure process and (2) the model stress can be obtained by muti-element information, which is one of the commands in RFPA system. Data files of stress can automatically be created, and curves of stress and displacement of each element can be displayed in each step of computation. Keywords: Rock Failure Process Analysis System (RFPA); roof control; roof to floor convergence; combined support

Jan 1, 2005

By Charlie Li

A cut-and-fill mine stope, located at a depth of about 1000 m in a lead-and-zinc mine, was closed down because of large roof convergence and fractures appearing on the hanging wall. The instability problem was owing to the relatively low strength of the rock subjected to high in-situ stresses. Extra reinforcement was required to secure the stope so that the remaining ores in the stope could be mined. Assessment of the fracture mode in the country rock surrounding the stope was carried out and then the reinforcement de- sign was worked out. It was proposed that the unstable section of the stope would be reinforced by bolt-shotcrete ribs as well as selective long bolts. The philosophy of the design was to hold up the fractured country rock by bolts and shotcrete so that a load-bearing arch could be formed in the roof and in the hanging wall. Six shot- Crete ribs were set up in the unstable section of the stope. Displacement measurements showed that the roof convergence reduced from about 2 &day to the ordinary creeping level, about 0.25 &day, immediately after the reinforcement operation. Six month later, the hanging wall collapsed into the stope in a place just outside the reinforced section, which indirectly proved the effectiveness of the bolt-shotcrete ribs in reinforcing the fractured country rock. This case showed that an appropriate rock mechanics assessment would form a solid base for reinforcement/support design. It also provided an evidence for the philosophy of the reinforcement by bolt-shotcrete ribs - establish a load-bearing arch in the rock.

Jan 1, 2005

By David Bartsch

The Ohio Valley Coal Company (Ohio Valley) has operated the Powhatan No. 6 Mine in Belmont County, Ohio since 1972. Ohio University owns a 455-acre research farm over a portion of the Ohio Valley reserve containing 51 acres of old-growth forest known as Dysart Woods. In 1988, when Ohio Valley applied for a new mining area for its first longwall located several miles away from Dysart Woods, Ohio University claimed that mining at that distance would lower the regional water table and kill the old trees. In response, Ohio Valley began to study potential impacts from longwall mining on hydrology, soil moisture, and tree growth. Early studies examined the impacts of longwall mining on hydrology, soil moisture, and tree growth directly over mined areas compared to woodlots that were not undermined. A subsequent study examined tree-ring growth for a five-year period before and after longwall mining for several woodlots, some directly over panels and others at distances of up to 2000 ft away. No significant differences in growth rate associated with longwall mining were observed. New research was begun that compared longwall-mining impacts on groundwater hydrology, available soil moisture, and tree growth in two stands of mature trees located near Dysart Woods in order to confirm the earlier results. Using a test technique known as "Before-and-After-Controlled-Impact-Pairs," data was collected from one woodlot (test) that was undermined and from another (control) that was not undermined. Data collection began several years prior to longwall mining and has continued for several years after mining. The data for the test site shows that although the shallow and deep groundwater levels were affected by longwall mining, the soil moisture, vigor rating, or the growth rate of trees did not decline significantly compared to the control site where there were hydrologic impacts. The study shows that there are no known significant impacts to trees from longwall mining. The results of these studies were used by Ohio Valley to obtain State approval to longwall to within 300 ft of Dysart Woods

Jan 1, 2005