Search Documents

By R. David Prengaman

During the past several years a new insoluble lead anode has been developed for copper electrowinning. The new anode consists of a rolled lead-calcium-tin alloy sheet attached to a slotted copper bus bar by a soldering process which produces a complete metallurgical bond between bar and sheet. The metallurgical bond greatly reduces the resistance between the bus bar and the lead sheet and the high conductivity does not deteriorate during the life of the anode. The rolled anode thins uniformly and does not suffer preferential grain boundary or internal corrosion commonly seen in cast anodes. The lead-calcium alloy containing a high tin content corrodes slowly because the rolling process produces a uniform, fine grained structure. The wrought product is very strong and ductile; and contains no internal defects, segregation, cracks, or pores which can reduce the life of the anode. Because the anodes corrode uniformly, a high percentage of the anode thickness can be utilized thus extending the life of the wrought anodes. The anode alloy composition which is stable only in wrought form, produces exceptional resistance to passivation during current interruptions. First introduced into liberator cells, the new electrowinning anodes have been specified as the anodes of choice for every new SX-EW tankhouse constructed in the last two years. This paper describes the new anode, its method of construction, service history, and how it differs from present copper electrowinning anodes.

Jan 1, 1987

By Toshihide Ito, Jie Liu, Takashi Nishiyama

"Human society evolved from an agricultural to industrial and, subsequently, to a service society. As the resource requirements for each stage of this development differ, trends of metal and energy consumption are related to shifts in society. The increase pattern of supplemental energy is similar to that of mineral production throughout the world. Low positive and stable long-term increasing occurred before 1950, whereas they increased quickly after 1950, especially between 1950 and 1973. A substantial decline in· the growth of energy and mineral production began in 1973 and lasted until the early 1980s. Production of energy resources has recently begun to increase again at a high growth rate in the world. Observing the consumption trends of energy and key metals, it is clarified that increasing patterns can be thought in three stages.IntroductionHuman society evolved from an agricultural to industrial and, subsequently, to a service society. As the resource requirements for each stage of this development differ, trends of metal and energy consumption are related to shifts in society [1-3]. Humphreys [4] described that both the non-ferrous metal consumption and the construction material consumption showed a similar trend dropping markedly in the UK over the period 1960-1992. On the other hand, per GDP (Gross Domestic Product) consumption, that is, the intensity of use of construction materials has declined sharply over the past 30 years, more so than the intensity of metal use in the USA [5]. Nishiyama [6] observed that increase pattern of supplemental energy is similar to that of mineral production throughout the world."

Jan 1, 2000

By A. R. Udupa

The reduction roasting behavior of chalcopyrite has been investigated using various combinations of a desulfurizing agent, i.e., CaO or Na2CO3, and a reductant, i.e., CO, H2 or C. Using these, combinations the sulfur is removed from the mineral as CaS or Na2S rather than SO2 as is the case with conventional copper smelting and converting. The laboratory reduction ex¬periments were conducted using thermogravimetric analysis (TGA) and boat tests of mixed combinations of fine particulate reactants subjected to a continuous gas stream. The degrees of metallization were determined by both weight loss and chemical analysis methods and the products examined using optical and scanning electron microscopy and electron probe microanalysis. The percent reduction after one hour at 900°C ranged from 60% to 94%. From these data It was possible to provide postulations as to the controlling reduction mechanisms.

Jan 1, 1983

By Young-Chul Kang

The Onsan Copper Smelter of LG-Nikko Copper Inc. is a unique plant, which has been operating two smelting processes since 1998. The operation of the first one was started in 1979 with a capacity of 80,000tpy of copper in concentrates utilizing Outokumpu flash-smelting technology. The other one was started in 1998 based on Mitsubishi continuous process with a capacity of 160,000 tpy of copper in concentrates. Through several expansion projects, the total smelting capacity of both processes is expected to reach 430,00Otpy of copper in concentrates towards the end of 2002. This article describes operation advantages of having two different processes at one plant and comparative operation results in terms of productivity, impurity distribution, energy consumption and environment issues and etc.

Jan 1, 2003

By B. Farouk, Y. G. Kim, D. Apelian

"Continuous strip casting has received considerable attention in recent years due to its economic advantages with increased energy savings and the elimination of intermediate processing steps. A promising concept in strip casting is the twin-belt (Hazelett) process which incorporates two cooled continuously moving thin metal belts wrapped around pulleys which tension and drive the belts at a predetermined speed. Molten metal is introduced at the entry end of the caster through a tundish and feeding nozzle into the mold. The twin-belt process has been successfully used with non-ferrous metals such as aluminum, copper and brass, and is a prime candidate for strip casting of ferrous materials. A numerical model has been developed which predicts the interface locations, the temperature fields in the solid and liquid regions of the cast and the velocity fields of the liquid metal at the entrance region of the twin-belt caster. The process variables considered are the velocity and cooling conditions of the belt and the nozzle shape. A body fitted coordinate system is used to track the front locations and to solve .the Navier-Stokes equations in the liquid region. Results obtained can help design efficient casters for thin strip steel castings. The development of the numerical model is presented, and sample results are discussed. I. IntroductionContinuous strip casting of steel has attracted world-wide concerns in recent years due to its economic advantages with increased energy savings and the elimination of intermediate processing steps. New methods of thin strip casting of steel are developing. One of the promising concepts is the Hazelett process, which is being used in nonferrous applications. The process incorporates two continuously moving, intensely cooled, thin metal belts. Metal blocks linked together are sandwiched between the moving belts and form moving side mold walls.In this work, the freezing front position, the temperature field and the liquid region flow field will be analyzed for the strip casting of metal using the twin belt caster (the Hazelett process). Up to now almost all theoretical analyses undertaken of the continuous casting of metal [1-3] have used a heat conduction equation, assuming slug flow in the liquid region. The effect of convection in the liquid pool during continuous casting were first investigated by Szekely and Stanek [4]. They considered potential flow between the feed metal orifice and the liquidus front, and slug flow in the mushy and solid regions of a vertical static continuous casting process for steel. Viscous effects and natural convection affects were not included Kroeger and Ostrach [5] studied the effect of natural convection flow in the liquid pool during solidification for a pure metal."

Jan 1, 1986

By Bowen Li

Copper vermiculite is a special nanomaterial with excellent antibacterial and antifungal performance. By means of ion exchange, copper vermiculite containing up to 5.8wt% copper was prepared. The chemical and mineralogical characterization of the material was investigated in this study based on the XRD, AAS, TEM and EDS analysis, as well as the calculation of crystalline parameters and crystal chemical formula. Cu2+ and Mg2+ have similar atom radius and same electrovalence. Correspondingly, the structure character of copper vermiculite is very close to that of standard Mg-vermiculite. Most of the CU21 may have occupied the interlayer cationic positions in the form of hydrate in vermiculite. However, some may have entered into octahedral coordinate positions. The values of au and bo of the copper vermiculite crystal cell have no obvious change compared to that of original vermiculite micropowder, but the Co value decreased slightly, which is desirable for the stabilization of the Cu2+ in copper vermiculite.

Jan 1, 2003

By Daniel A. Norrgran

Grinding ball fragments discharging from SAG mills and ball mills causes extreme wear to downstream processing equipment. These ball fragments, recirculating in a milling circuit, will cause excessive wear to sumps, pumps, hydrocyclones, and interconnecting piping. A magnetic separation system to remove grinding ball fragments from the mill discharge has been developed and successfully applied in the milling circuit. This magnetic separation system - termed Trammel Magnet - was first applied at the Escondida copper concentrator in Chile. The Trommel Magnet consists of an arc of permanent magnets mounted at the discharge end' of the tommel screen. The magnetic arc attracts the ball fragments and removes them from the process stream. This retrofitted magnetic separation system removed 126 metric tons of ball fragments from the circulating load of a. single ball mill in the initial 24 hour period. The mill has since stabilized and the magnetic separator is currently removing 7 metric tons per day of ball fragments. The retrofit of the Trommel Magnet has: 1. Extended the pumpp life and the hydrocyclone life approximately 300 percent. 2. Provided a 5 percent increase in the throughput of the mills by removing grinding ball fragments that contribute very little to the grinding process. Variations of the Trommel Magnet have also been developed for removing grinding ball fragments directly from the mill discharge without the use of a trommel screen. In each case, permanent magnets are used to collect the ball fragments from the mill discharge stream prior to reporting to the sump. These other systems have been designed and fabricated for in-plant test work.

Jan 1, 1999

By Kiichiro Hayashi

"Indonesia is one of the world leaders in palm oil production. Palm oil industry is an industry to be considered when it comes to environmental impacts. This paper utilizes three step approaches. First, a material flow analysis of palm oil related industry was conducted in Indonesia. Second, a factory visit survey was conducted for getting information on environmental impacts of plantation and CPO mills. Third, a LCA study was made for a model Indonesian CPO mill in several bio-waste treatment options. Main findings were that, first; over 70% of FFB was bio-wastes generated from CPO mills. Second, some mills introduced a zero emission bio-waste policy. However, untreated bio-wastes in the zero emission policy, such as, CH4 from POME ponds, may have potential to reduce more impacts on the environment. Introduction Indonesia is one of the world leaders in palm oil production with approximately 12.4 million tons of crude palm oil (CPO) production in 2005 and with the plantation area 5.6 million ha spreading out in 19 provinces [10]. The expansion of palm oil cultivation in Indonesia and its export oriented industry heavily relies on the strong world market demand for food. Currently, there are 320 CPO industries in Indonesia [10]. These include plantations and palm oil related factories. Among them, there are six biggest players in CPO business in Indonesia: PT. Perkebunan Nusantara (PTPN) consisting of 9 PTPN, Sinar Mas, Raja Garuda Mas, Astra Agro Lestari, Minamas Plantation and Indofood. They are managing more than 50% of plantation estate in Indonesia and are leading the Indonesian palm oil business.Palm oil industry is an industry to be considered when it comes to environmental impacts. Unfortunately, there is not so much available information related to the performance of each CPO on environmental impacts. There are reports which provide information on environmental impacts of CPO mills in South East Asian countries, but are limited to, for instance, Thailand’s cases [4 and 5] and Malaysia’s cases [1, 3, 6, 7, 9, 11 and 12]. On the other hand, similar studies on the Indonesian’s case are not well established in academic literatures. And also there is limitation on Indonesian palm oil industrial information from plantation to consumption and disposal in academic articles. There is no literature related to material flow analysis focusing on the whole Indonesian palm oil related industry. One way to describe and present the environmental impacts is through a life cycle assessment (LCA). The LCA could be used to estimate the impacts of CPO production including the stages of plantation, transportation and milling [5, 8 and 11]. However, studies on Indonesian CPO production process were not well established in academic articles. The purpose of this paper is thus to clarify environmental impacts of palm oil industry in Indonesia especially by focusing on plantation and CPO mills with consideration to various bio-waste treatments."

Jan 1, 2008

By Maija-Leena Metsärinta

The behaviour of copper and lead in zinc roasting has been studied in laboratory scale roasting experiments as well as in large scale trials in an industrial fluidized bed, with the background of Outokumpu Kokkola Zinc smelter. Commercial zinc concentrates with a low and high ( up to 3 wt % ) copper content and with a low and high (up to 3.5 wt % ) lead content were oxidized to various desulphurisation degrees in the fluidized bed to establish the reaction mechanisms and the paths for copper and lead oxidation in the roasting. Influences of the agglomerate size on the roasting kinetics and micro-scale phenomena were also determined. Optical microscopy was used on the calcine and the findings are presented as numerous photographs of the polished cross sections. SEMIEDS techniques were used for analyzing chemically the phases and particle morphologies present in the samples. Computational thermodynamics was applied to the complex phase equilibria occurring during roasting in the agglomerating calcine. A complete oxidation of zinc concentrate with a high copper and lead content requires a careful control of oxygen coefficient in the roasting in order to maintain a stable operation of the fluidized bed. Oxygen coefficient thus seems to have a significant impact on the hydrodynamic stability of the fluidized bed with fine raw materials.

Jan 1, 2003

By Cong Wang, Siyang Long, Pengcheng Zhang, Haibin Zuo

The present study describes central segregation of the High-carbon steel billets of 150mm square and its heredity to the following hot-rolled wire rods, whose sizes are 10mm and 6.5mm in diameter separately. The relationship between center segregation of the billets and solute element distribution of rods, the mechanical properties and microstructure of rods were studied experimentally. The results show that segregation index of C is higher than that of Mn. With the increase of central segregation, the stability of the mechanical property of the rods becomes worse. The formation of carbide network and central martensite in the rolled products can be attributed to the heredity of the as-cast central segregation. The 6.5mm-diameter-rod has higher tensile strength than that of 10mm diameter which might be due to bigger reduction ratio. Thermo Mechanical Control Process (TMCP) should be used together with Billet Centersegregation- controlling (BCSC) to improve the overall properties of rolled products effectively.

Jan 1, 2016

By Hiroyuki Sano

A closed recycling process for the low-grade scrap of Al-based composite materials was developed. In this process flux treatment with water-soluble halide is a key technique. In the present work, flux treatment conditions were discussed from the viewpoint of the separation and the recovery of the base material, reinforcement and flux. Optimum separation condition was obtained for the NaCl-KCI-KF flux treatment. The recovered aluminum alloy can be recycled for various usages. The recovered SiC particles cannot be reused as reinforcement because of the coexistence of the contamination, therefore it is necessary to eliminate these contaminates or to find another use. The recovered flux is reusable with supplemental addition of fluoride.

Jan 1, 2003

By ZhiLong ZHAO, Lin Lin, Zhancheng Guo, Jingtao GAO, Huiqing Tang

Grain sticking often occurs in the fluidized bed reduction of f ine iron ore, which is closely related to the precipitation morphology of metallic iron on the surface of ore particles. In this work, simulating the gas-solid reduction process of iron ore, in situ observations were carried out to investigate effects of doping mineral oxides on the precipitation morphology evolution of metallic iron during reduction of iron oxides with CO. Results indicate that the precipitation morphology of metallic iron is related to the quantity of doped mineral oxides. The minimum mole fraction of doped oxide ( xyOA N ) that can inhibit the growth of iron whiskers is related to its cation radius ( Ax r ), extranuclear electronic layers ( Ax n ) and valence electrons ( Ax q ). Their relation can be expressed as:

Jan 1, 2016

By Fjeldstad Karin Jusnes

Two quartz types used in the silicon and ferrosilicon industry were heated to temperatures of 1600 and 1700 °C. The parameters varied were the temperature and the holding time at maximum temperature. The amount of quartz, cristobalite and intermediate amorphous phase were measured using XRD and the internal standard method. Type P showed a much larger ability to transform to cristobalite at lower temperatures than type A. Type P had a larger amount of alkali and alkaline earth impurities. This could have enhanced the transformation to cristobalite. For quartz type A the amount of cristobalite was larger at 1600 °C than 1700 °C. This can also be seen for some of the samples of type P at shorter holding times.

By S. Eckert, G. Gerbeth, K. Timmel, B. Willers, T. Wondrak, N. Shevchenko, M. Röder

The quality of the produced steel in the continuous casting process is significantly governed by the melt flow in the mold. However, direct flow measurements in liquid metals are still rather scarce. In order to investigate these flow phenomena, three experimental facilities operating with low melting liquid metals were installed at Helmholtz-Zentrum Dresden-Rossendorf (HZDR). The melt flow in the models is measured by the Ultrasonic Doppler Velocimetry (UDV) or the Contactless Inductive Flow Tomography (CIFT), multi-phase flows can be visualized by X-ray imaging. The obtained measurement results are primarily used for validation of numerical models. In this paper we will investigate the fluid flow in the mold and the behavior of the surface of the liquid metal using flow measurements by UDV and surface profile measurement by a laser scanner, respectively. Strong fluctuations and deviations of the free surface were observed in case of a static magnetic field

Jan 1, 2016

By R. C. Nascimento

It was investigated the effect of the addition of bentonite on the physical propertiesof pellets produced from fines of manganese ores. Cold-bonded pellets were produced. Pellets bearing up to 1 wt% of bentonite were submitted to strength compression resistance tests, fatigue of pellets to impact and maximum height of fall tests. A correlation of resistance of the pellets and time for curing were stablished. The produced pellets match the conditions for raw materials used in electric smelting hrnaces to produce manganese based ferro-alloys.

Jan 1, 1995

By Onuralp Yücel, Mehmet Bugdayc, Murat Alkan

"In this study, iron based alloys (Fe-Mo, Fe-Cr-Ni, etc.) were produced by using aluminothermic methods starting from Mill Scales obtained continuous casting processes. Mill scales are an oxidised layer of steel alloys containing iron oxide, which includes + 2, + 3 values, on the surface of slabs and billets occurring during annealing in heating furnace at integrated iron and steel milling plant, and continuous casting unit. In the metallothermic experiments, different ratios of starting mixtures and addition of the oxide powders (Alz03, Si02, CaO, MgO) were examined, and their effects on the metal recovery and alloy compositions were carried out. The samples were characterized by using chemical analysis (AAS), XRD, XRF and SEM/EDS techniques.IntroductionSelf Propagating High Temperature Synthesis process (SHS) has many favour compared to the furnace applications, such as low energy requirement, low cost, very short processing time and simple operation, [l, 2]. In a SHS process, the ignition starts the combustion and propagates throughout the reactant mixture yielding the desired product. However, the disadvantages of the process such as inhomogeneous or unreacted products due to undesirable reaction rates needs to be overcome by changing some parameters such as ignition temperature, particle size, additive, atmosphere etc. [3, 4]. Mill scale is a layer of iron oxide which forms on ferrous materials cooling after being processed in hot rolling or continuous casting plants. Mill scale contains iron (II) and iron (III) oxides, which result in a 70% total iron content in oxide form. Not being able to reuse this material will prevent the raw material entering the production plant from being fully utilized [5]. This study aimed to produce Fe-based alloys via SHS (Self Propagating High Temperature Synthesis) metallurgy which is attractive process technique regarding fast and low-cost production ability of cast alloys by using high metallic iron content by reducing continuous casting mill scale."

Jan 1, 2013

By H. Castillo

This paper describes the computer simulation of thermal stress fields generated in the quenching of the ns 415 H Steel automotive parts (Valve Lifters), running the ANSYS Multiphysics software of finite element (FEM). Simulation was performed introducing residual stress measurements on specific values areas, like internal pressure condition in the material. The stress condition effect in the material and the properties as temperature function data, were introduced to the FEM software. The thermal stress simulation was made on the 2D system. The parts were austenized to 850 900 °C and then oil quenched, tempered at 150 -200°C, and air cooled. The X-Ray diffraction technique was made to take measurements from residual stresses on valve lifters surfaces. The results analysis showed the ideal stress condition necessary in raw material to reduce the scrap percent in grind operations after hardening heat treating process. Keywords: Thermal Stresses, Temperature profile, Computer Simulation, Finite element analysis, Quenching of steel, Residual Stresses

Jan 1, 2003

By Qingchun Yu, Bin Yang, Yong Deng, Heng Xiong, Fei Wang, Minxiu Chen

"Metal aluminum produced by non-electrolysis process received much attention due to its lower energy consumption. In this paper, carbothermic reduction and carbothermic-chlorination of alumina in normal pressure and vacuum were studied. The products were examined by means of XRD, EDS and SEM. During the carbothermic reduction process using carbon reductant in normal pressure, no metal aluminum was found. However, when coal was used as reductant, a mixture containing metallic aluminum, A14C3, and silicon was obtained, but metallic aluminum couldn't be separated from the mixture. During the carbothermic-chlorination process in vacuum, Al404C and Al4C3 were produced by the reaction between alumina and carbon, and Al Ch gas reacted with Al404C and Al4C3 to produce Al Cl gas. Metallic aluminum was produced due to the disproportionation of A!Cl gas and condensed on the collecting plate. Meanwhile, the initial temperature of carbothermic reduction of alumina reduced in vacuum compared with that in normal pressure.IntroductionIndustrial production of primary aluminum is carried out in alumina cell by the so-called Hall- Heroult process, necessitating the use of very high currents of low voltage. The alumina from which metallic aluminum is gained must be chemically pure, otherwise impure metal results. The main drawbacks of the electrolytic production are its very high energy consumption, the release ofperfluorocarbons, and the high specific C02 emissions [1]. During the past years, there were a lot of attempts to produce metallic aluminum by carbothermic reduction of A1203 [2, 3]. Cox [4] determined the vapor pressure over the A1203-C system and performed X-ray diffraction analysis of condensed products. It was demonstrated that an increase in the carbon content in the system leaded to the sequence of transitions: A1203~Al404C~A1zoc~A14C3 ~AI [5]. In any carbothermic reduction process for aluminum, extremely high temperatures (2000 °C ) were required [6]. In spite of considerable effort, the carbothermic reduction of alumina to aluminum remains a formidable technical challenge, due to the high temperatures required, and to the formation of aluminum carbide and oxycarbide byproducts [7]."

Jan 1, 2013

By M. I. Novgorodova

Most of the gold in the earth's crust occurs as finely-dispersed gold and accounts for much of the gold lost in extraction processes and during exploration for gold. The Compositions, sizes, and morphology of fine gold particles (0.01 to 10 ~m in diameter) were studied with high resolution electron microscopy coupled with electron microprobe and microdiffraction devices, using colloidal carbon replicas. Correlations were made between fine gold, mineral associations and ore genesis. The results provide qualitative information on the proportions of finely dispersed, invisible and visible gold distribution in ores. Such knowledge is fundamental when planning an optimum technological recovery process.

Jan 1, 1991

By Xiping Chen, Wangxing Li

"Spent potlining is unavoidable solid waste from aluminum smelters. About thirty kilograms spent potlining is discharged in China to produce per ton primary aluminum. Spent potlining has high level soluble fluorides and cyanides so that it brings heavy pollution to environment. It is prohibited to keep a large amount of spent potlining in open air because it will lead concentrated pollution to local soil and water source due to hydrated reactions between spent potlining and rain water/moisture in air. Landfill may solve pollution of spent potlining provisionally, but it is difficult to be accepted by aluminum smelters because of its high investment, troublesome monitoring and perennial maintenance. Detoxifying of spent potlining not only can remove deleterious fluorides and cyanides in SPL, but also can make fluorides in SPL recycle and return to aluminum electrolysis cells, at the same time benign SPL solid residue can be recycled and ready for cement production.IntroductionChina became the largest primary aluminum manufacturer in 2001. In the past few years, its aluminum output increased by twentyfive percent every year and reached 12.56 million metric tons in 2007. The whole world was very surprised and focused attention upon Chinese aluminum industry. It is more and more important to keep sustainable and steady development with the rapid development of Chinese economy. Aluminum industry is an important base industry and does a great contribution to Chinese economy. But aluminum industry is high energy-consumption and heavy-pollution industry. The government has paid more attention to aluminum industry in recent years. Nowadays the bothersome problem which counterworks Chinese aluminum industry is pollution from solid wastes. Main Solid wastes from aluminum industry are red mud from alumina refineries and spent potlining (short as SPL) from aluminum smelters. Spent potlining are waste lining materials from aluminum electrolysis cells. During production of aluminum, due to reactions between melted electrolyzer and pot lining as well as penetrating of fluorides into pot lining, newly-formed compounds inlayed in pot lining, destroyed the lining structure and brought pot lining cracking. Melt rushed out of lining cracks, cells have to be stopped running and ready for heavy repair. Cell life generally varies from 1500 to 2000 days. Spent potling is an unavoidable solid waste from aluminum industry."

Jan 1, 2008