Search Documents

By A. H. Rhoades

The modern polarizing microscope with such accessories as cameras, infrared devices, reflectance and/or transmission photometers, indention hardness, and heating stage is used to characterize coal, coke, and other carbon forms. It allows characterization of coke by-products, such as tars and pitches and their insoluble residues. A useful product of the microscopic approach is the coal petrographic analysis which permits the prediction of coke strength carbonization pressure and volume change. Carbonization tests are expensive, time-consuming and require large amounts of coal. Tests on the coke show it to be strong or weak but give no indication of why. Petrographic analysis requires grams of coal and yields data that indicates why the coal produces coke of a given quality. Small samples from drill cores are sufficient for petrographic analysis. These data are also used to optimize blends for coke production. When coke-plant problems occur, ~he microscope can be used to check the coal blend proportions, as well as for weathered coal. Microscopy is useful in spore correlation work which may be a prerequisite to sound coal reserve estimates. Dispersed vitrinoid reflectance studies are used to determine the degree of organic metamorphism which serves to establish oil and gas deadlines. Tars and pitches are examined microscopically for the amount of normal solids as well as the size of undesirable carry-over solids resulting from pollution abatement practices in coke works. The microscope is also used to study coals for gasification and liquefaction.

Jan 1, 1981

By Fu-Shen Zhang, Mengjun Chen, Jianxin Zhu

"A novel approach for foam glass preparation, namely vacuum-aided powder sintering technique, was preliminarily investigated in the present communication. The key point of which was to prepare foam glass at a negative pressure. Compared to normal powder sintering process, the new approach could benefit the foaming process by shorting the holding time, reducing the amount of foaming agent and especially decreasing relative density of the product. Optimum conditions were 750 °C, 1000 Pa, 5 min and 1 wt.% foaming agent, respectively.IntroductionFoam glass represents a highly valuable solution for thermal and acoustic insulation, since it possesses a generally higher mechanical, chemical and thermal stability than other foams'1'. The first industrial processing for foam glass production, the direct introduction of gases (""blowing"") into the special molten glass, can be dated back to the end of 1930s'2'. At present, almost all foam glasses is prepared by powder sintering technique instead of blowing,3 since it reduces the temperature by several hundred degrees. Moreover, as fine glass powders or similar powders can be used to substitute corresponding glasses by this technique, considerable attention has been focused on the production of foam glass by considering fully recycled glasses, coal fly ash, or other solid wastes as raw materials,4 especially CRT glasses'3' 5', on the point of environmental protection.In a previous report'6', when discussing the lead removal and recovery from CRT funnel glass by a pyrovacuum process, we found that foam glass could be prepared at a negative pressure. Therefore, in this communication, the similarities and differences between the powder sintering process for foam glass at normal and negative pressure was preliminarily discussed."

Jan 1, 2011

By John W. Graydon

Incineration is an attractive alternative to the disposal of MSW in landfill sites. However, the process of incineration generates fly ash which contains significant levels of leachable heavy metals - particularly cadmium, lead, and zinc - and it is essential to manage this fly ash in an environmentally sound manner. The compositions, phases, textures, morphologies and size of fly ash particles have been studied by light microscopy, scanning electron microscopy, X-ray microanalysis, and X-ray diffraction. The detailed spatial relationships and speciation of the environmentally significant constituents have received particular emphasis. The information obtained is useful in understanding how fly ash is formed during incineration, in understanding the leaching behavior of untreated fly ash if it is disposed of in a landfill and, most importantly, in guiding the development of the best treatment strategies for fly asti to mitigate its environmental impact.

Jan 1, 1992

By Niko Hellstén

To capture efficiently the valuable trace metals from nickel slag using electric furnace, it is important to study their distributions between the slag and metallic phases in the furnace. It is impossible to calculate accurately these distributions without experimental measurements. Therefore, in this work, selected trace metal distributions and phase equilibria between K2O containing iron-silicate slags and a metallic Ni-Fe-Cu alloy in nickel slag cleaning furnace conditions were studied. The experimental method developed and applied during the work, involved a modified quenching technique that included equilibration of the samples in semi-sealed quartz ampoules in an inert atmosphere and metallic Fe saturation. The use of the semi-sealed quartz ampoule prevents the escape of volatile elements from the sample during equilibration. Chemical compositions of the phases and the trace elements were analysed by EPMA. From the measured compositions, the trace metal distribution coefficients between the molten Ni-Fe-Cu alloy and slag were calculated.

By N. Tsuchida

Sumitomo Metal Mining Co. Ltd. (SMMC) is currently developing the flowsheet to treat stockpiled limonite, a type of laterite ore, at Rio Tuba on southern Palawan Island, Philippines. The new plant will be commissioned at the end of 2004. Rio Tuba Nickel Mining Corporation (RTNMC) has been mining saprolite since 1977, and the limonite ore located above the saprolite ore body has been stockpiled separately according to nickel and magnesium content. Ore from these stockpiles will be blended and used for the operation. The annual production of nickel will be 10,000 metric tons for the next twenty years. The proposed process consists of ore preparation, high pressure acid leach (HPAL), counter- current decantation wash, impurity removal and sulfide precipitation. Precipitated mixed sulfide will be processed to electrolytic nickel by the Matte Chlorine Leach Electrowinning (MCLE) process at Niihama, Japan. SMMC has established new technologies during the process development, such as zinc removal and sulfide precipitation. Applying this technology, preferential removal of zinc can be achieved by hydrogen sulfide gas with negligible loss of nickel. Precipitation of nickel by hydrogen sulfide gas is carried out at low temperature. Slow kinetics is selected for control of the particle size of the precipitated mixed sulfide. Keywords: HPAL, Zinc Removal, MS Production

Jan 1, 2004

By Raghavan Srinivasan, Y. V. R. K. Prasad, William G. Frazier, Steve C. Medeiros

"Aerospace gas turbine disks operate in an environment of relatively high stresses caused by centrifugal forces and elevated temperatures. These severe conditions necessitate the need for materials with good high temperature strength and low cycle fatigue resistance. One class of alloys used for this task is the nickel base superalloys, out of which, lN 718 is the most widely used in the aerospace industry [I]. The properties of IN 718 are attributed to the combined effects of the chemistry, heat treatment, and microstructure. The chemistry is tailored not only for solid solution strengthening but also for precipitation hardening developed during heat treatment, which combined with a fine grained microstructure lead to excellent mechanical properties such as low cycle fatigue resistance and elevated temperature strength. The properties of a gas turbine disk are sensitive to the microstructure, in particular the grain size, which is dependent on the processing history. The ability to precisely control the microstructural development during forging is dependent on controlling the process so that the workpiece is deformed within a ""safe"" region where no microstructural damage or flow instabilities occur. The microstructural mechanisms during deformation may themselves vary within the ""safe"" region and it is desirable to determine them within the range of parameters that are commonly used in industrial processing. The objective of this work is to establish a relationship between the grain size and the process control parameters i.e., temperature and strain rate, in the hot working of IN 178.BackgroundIN 718 belongs to a class of nickel-iron base superalloys with a face-centered cubic (FCC) austenitic matrix strengthened by precipitation of ordered intermetallic or carbide precipitates and is a nickel-rich alloy strengthened by ordered body centered tetragonal (BCT) precipitates, Y"". The alloying of nickel and iron results in the formation of the austenitic matrix, y, while the addition of chromium and molybdenum cause solid solution strengthening. Also, alloying with niobium causes precipitation of the metastable hardening constituent Y"" (Ni3(Nb,Ti)). Extended aging treatments in the temperature range 650 °C - 980 °C allow the more stable orthorhombic 8 phase (Ni3Nb) to form. Trace amounts of boron are also added to serve as grain boundary strengtheners for high temperature creep resistance. Hot deformation of IN 718 is performed between the Y"" and 8 solvus temperatures to facilitate recrystallization and to control grain growth. While deformation below the Y"" solvus (""""962°C) produces no change in grain size, deformation above the Y"" solvus but below the 8 solvus will lead to a dynamically recrystallized microstructure. The presence of the 8 precipitates will pin the grain boundaries after recrystallization and restrict grain growth so that a fine grain microstructure is obtained. Deformation above the 8 solvus ("""" 1038°C) will lead to a microstructure which has undergone grain growth during deformation."

Jan 1, 2000

By M. Nilmani, J. Sofra

The transverse distributions of the solids discharge velocity and mass flux at the discharge end of vertical and inclined lances were measured in order to detennine the transverse distributions of the axial momentum flux, which is a dominant factor influencing the penetration behaviour of particles into melts during submerged injection. The effects of gas velocity (10 - 30 m/s), solids loading (5 - 10), lance length (0.15 - 1.0 m), lance inclination (vertical downward - horizontal) and particle density (2500 - 8900 kg/m3 ) were investigated, while the lance diameter and particle size were fixed at 10 mm and 220 µm respectively. The particle velocities and mass fluxes were measured by image analysis of particles illuminated in a laser-generated light sheet aligned vertically through the axis of the lance at the discharge point. The particle discharge velocity profiles for vertical downward flows were synunetrical about the centre-line of the lance, with the maximum velocities occurring at the centre-line. The velocities increased with increasing gas velocity, increasing lance length and decreasing particle density in accordance with previous observations. The transverse mass flux profiles were also synunetrical for vertical downward flows, however at the lower gas velocities the peaks in the profiles were displaced from the centre-line of the lance by a fractional diameter of about 0.15. The particle discharge velocity profiles become increasingly asynunetric as the lance orientation was changed from vertical to horizontal, with higher particle velocities present near the top wall of the lance. The mass flux profile also became asyrrunetric as the horizontal orientation was approached, however in this case, the profile became biased towards the bottom of the lance. The effect was much more pronounced for a gas velocity of 10 m/s than for 30 m/s, showing the relatively stronger gravitational influence as the velocity was reduced.

Jan 1, 1996

By Fathi Habashi

The recovery of uranium from wet process phosphoric acid was applied on industrial scale in the 1940's by using octylpyrophosphoric acid as an extractant. Later, more efficient reagents were used, e.g., di(2-ethylhexyl) phosphoric acid and actylphenyl phosphoric acid. In the 1970's the rare earths in Kola phosphate were recovered in Finland and recently (1997) in Norway using HNO, as a leaching agent and di(2-ethylhexyl) phosphoric acid as solvent. It was demonstrated later on laboratory scale that both uranium and rare earths could be extracted from the rock by tributyl phosphate but at different pH values provided that the rock is leached with nitric or hydrochloric acids instead of the commonly used sulfuric. This new concept opens the way to the possibility of treating phosphate rock by in-situ, dump, or vat leaching for the recovery of phosphate values as well as uranium and the rare earths. Another solvent extraction process is used industrially for the purification of phosphoric acid using butyl and amyl alcohols.

Jan 1, 1998

By Takafumi Kondo, Satoshi Yamashita, Noboru Masuko

"Aqueous oxidation of phosphite ions to phosphate ions with dissolved oxygen was examined at 80° C and pH 4.5 mainly from the stichiometric point of view. Dissolved oxygen alone can not oxidize sodilim phosphite in aqueous solution, but when sulfur dioxide is coexistent, cooperative oxidation for both sulfite and phosphite can occur in aqueous solution. Sulfur dioxide itself is well known as a reducing agent, but it also reacts as an oxidation-promoting agent for other species under a certain condition. So sulfur dioxide is· a promising cheap reagent for waste phosphite processing.IntroductionIn a liquid-phase oxidation reaction using the dissolved oxygen gas, the eoexistence of a copper salt is required generally. Recently, it was reported that the oxidation reaction progressed by using mixed gas of sulfur dioxide and oxygen without the copper catalysis, and the attention has been collected1·3). The present authors also noticed the phenomenon since the early time and have been studying on the reaction mechanism of sulfur dioxide in liquid phase oxidation 4l. It was found that; by using the SO2-O2 mixed gas, the oxidation of phosphite ions to phosphate ions proceeded efficiently in sulfuric acid solutions. In the present report, the applicability of SO2-O2 mixed gas as a cheap oxidizing agent to the industrial processing of the waste solution of electroless nickel· plating is investigated. It is well known that the sulfur oxide dissolved in aqueous solution is oxidized ·by the oxygen in the air to sulfuric acid according to the following equation"

Jan 1, 2000

By Hiroshi Hashimoto

For the application of sodium carbonate slag treatment to product high purity copper on an industrial scale, the counter-flow batch process that reduces the amount of utilized slag is proposed from the viewpoint of the post-treatment of slag. Based on the distribution ratios of several impurities between the slag and molten copper determined previously, the effectiveness of this process is discussed using a mathematical model and confirmed experimentally. According to the model, the slag consumption to remove Sb to a required level in case of the counter-flow batch process with 3 reactors is calculated to be around 30 % of that in the case of an ordinary batch process, where pure sodium carbonate is used as a slag at every stage.

Jan 1, 2003

By K. Adham

For use in many existing and emerging applications, the purification of natural graphite is required to achieve +99.9% carbon content with minimum metallic impurities. Currently, the hydrofluoric acid process is used, which carries certain environmental and workplace health and safety impacts. While thermal purification of graphite at temperatures over 2500 °C is a known alternative, such high-temperature furnaces are expensive to build and operate. Using chlorine at lower temperatures to purify graphite is also known and patented, but is currently limited to treating solid synthetic graphite shapes in small-scale batch furnaces. Chlorine treatment of natural flake graphite resources can be used commercially, if certain drawbacks are addressed through process improvements that can be helped with the use of fluidized bed reactor technology.

By Li Kaihua, Li Liang, Miao Qingdong, Wang Cong

The current process of production of titanium sponge involves the use of TiCl4 as a feed material and a huge amount of heat is generated during the magnesiothermic reduction process. For this reason, it is possible to agglomerate into a titanium lump with the partial high temperature. And, it is difficult to obtain soft titanium sponge with low content of impurities. In order to solve the current problems in the titanium sponge production process, process optimization experiments study of TiCl4 feeding speed, vacuum distillation temperature, system pressure and time control had been conducted for obtain high quality titanium sponge. Experimental results show that lower feeding speed can improve the output capacity of titanium sponge and softer products can be obtained. The product grade rate of titanium sponge improved significantly.

Jan 1, 2015

By Sanaz Mosadeghsedghi

The feasibility of the application of electrodialysis in separation of light and heavy rare earth elements (REE) in synthetic solutions was investigated. The experiments were carried out using single and binary solutions of a light (cerium) and heavy (ytterbium) REE. The effects of electrical voltage, electrical current, and the addition of complexing agent (EDTA) to increase the separation selectivity were investigated. Separation of Ce and Yb was achieved in binary solutions with and without the addition of EDTA. Higher degrees of separation were seen at higher voltages. Ce–Yb separation was more significant in the presence of EDTA. The separation factor of Ce–Yb and Ce–Yb-EDTA were 1.44 and 2.60, respectively.

By Donald R. Sadoway

"Molten salt electrolysis is a proven technology for the extraction of metals -- all· the world's primary aluminum is produced in this manner. The unique properties of molten salts also make them excellent media in which to treat a variety of forms of waste. Of special note in this regard is electrolysis in molten oxides, a concept put forward by the author, initially as a ""clean technology"" for producing primary metal. However, in the context of waste treatment, electrolysis in molten oxides is a process offering the prospect of changing the-valence of dissolved heavy metals while making pure oxygen gas as the main by-product. Laboratory tests conducted at a temperature of 1550°C on chromate sludge dissolved in an melt composed of Al2O3, SiO2; CaO, and MgO have confirmed electrochemical production of oxygen on a carbon-free anode. IntroductionMolten salt electrolysis is the electrolytic decomposition of a compound dissolved in an ionic melt. The prime example of this process can be found in the production of aluminum. The compound, alumina (Al2O3)' derived from the mineral bauxite, is dissolved in an ionic melt comprising a multicomponent solution of cryolite (Na3AlF6)' aluminum fluoride (AlF3)' and calcium fluoride (CaF2,). The products of electrolysis are molten aluminum and carbon dioxide, the latter due to the attendant consumption of the carbon anode. Primary aluminum is produced in a reactor known as the Hall cell.' Alternatively, the compound undergoing electrolytic decomposition can be derived from waste. Processing in molten salts, with their capacity to dissolve materials to very high concentrations compared to those attainable in aqueous solutions, can be rather advantageous. High solubilities lead to high limiting current densities, and this, in tum, results in high productivities: For a primer on molten salt electrolysis and a review of the basic literature in the field of molten salts the reader is directed to an earlier publication of the author (1)."

Jan 1, 1996

By Donald R. Sadoway

Molten salt electrolysis is a proven technology for the extraction of metals -- all the world's primary aluminum is produced in this manner. The unique properties of molten salts, also make them excellent media in which to treat a variety of forms of waste. Of special .note in this regard is electrolysis in molten oxides, a .concept put forward by. the author, initially as a ."clean technology" for producing primary metal. However, in the context of waste treatment, electroly-sis in molten oxides is a process offering the prospect of changing the. valence of dissolved heavy metals while making pure oxygen gas as the main by-product .Laboratory tests conducted at a temperature of 1550°C on chromate sludge dissolved in an melt composed of Al2O3 and MgO have confirmed electrochemical production of oxygen on a carbon-free anode.

Jan 1, 1996

By Rodney L. Williamson

Optimal estimation theory has been applied to the problem of estimating process variables during vacuum arc remelting (V AR), a process widely used in the specialty metals industry to cast large ingots of segregation sensitive and/or reactive metal alloys. Four state variables were used to develop a simple state-space model of the V AR process: electrode gap (G), electrode mass (M), electrode position (X) and electrode melting rate (R). The optimal estimator consists of a Kalman filter that incorporates the model and uses electrode feed rate and measurement based estimates of G, M and X to produce optimal estimates of all four state variables. Simulations show that the filter provides estimates that have error variances between one and three orders-of-magnitude less than estimates based solely on measurements. Examples are presented that verify this for electrode gap, an extremely important control parameter for the process.

Jan 1, 2001

By C. W. Whitten

Solis from an abandoned Pb battery processing facility were characterized prior to the selection of the extraction technique. Reflected light microscopy and electron beam methods were used to locate Pb-bearing phases and to quantify the compositions of the phases. It was found that the soils are composed primarily of quartz and feldspars with minor amounts of iron and titanium oxides. Lead is primarily present as an oxide or sulfate that is associated with the silicate minerals. Specific phases identified were PbO; Pb02; cerrusite, PbCO3; angleslte, PbSO4; galena, PbS; and magnetoplumbite, 2PbO3Fe2O3; or plumboferrite PbO2Fe2O3?

Jan 1, 1989

By Augusto Viana Leandro Teixeira

Rare Earth Elements (REE) are fundamental for modern life products and green technologies. Supply constraints and the price peak of 2011 boosted intensive research for alternatives for processing and separation. Complex monazite- type, rare earth ores usually contain high acid consumption impurities, such as iron and aluminum, and radioactive thorium in their composition. These impurities are not removed by conventional concentration processes due to fine, micro-level association between the REE carrying minerals and the gangue minerals. This work presents a selective process route for REE extraction from iron-rich, monazite ores. The process involves sulfation by addition of concentrated sulfuric acid and pyrohydrolysis at temperatures of approximately 700–750 °C. Experimental results show REE extraction higher than 70% and low iron (below 5%) and thorium extraction (below 10%). A method based on thermogravimetric analyses was shown to be adequate to predict the behavior of a given ore sample in the sulfationselective pyrolysis-leaching process.

By Jing Zhan, Tian-zu Yang, Wei-feng Li, Li-Hua Jiang, Shi-yan Xu, Jian-yang Huang, Chuan-fu Zhang, Yan-qing Fan

The amount and activity of coal, reduction temperature and other parameters of the process of bottom-blown reduction of liquid high lead slag were investigated in laboratory. Methods to strengthen the bottom-blown reduction process were studied by industrial production. The results were in the follows: the reduction temperature was 1150℃; reduction time was 1.5h; the reductant was anthracite; lead content in slag was controlled to 2%; the rate of coal was 7% and gasification loss of coal in high temperature was severe; liquid lead slag reduction rate was faster with coal; prolonging the reaction size had little effect on reducing lead in slag; the size of the reactor can be further reduced.

Jan 1, 2015

By Jiang Diao, Yong Qiao, Xuan Liu, Tao Zhang, Bing Xie

Adding CaO into the vanadium extraction converter is an effective way to decrease the dephosphorization burden in subsequent steelmaking process. The crystallisation process of spinel is one of the most decisive factors in the subsequent extraction. The theoretical calculation results show that the temperature of the peak total crystallization rate will decrease 5K with basicity increasing 0.1. The relation between cooling conditions and grain size of spinels is also discussed. It is found that low cooling rate and high basicity benefit spinel crystal growth. And the non-isothermal crystallization kinetics results indicated that the restriction factors of spinel growth is that solid crystals accept new components from liquid-solid interfacial. While the sample was cooled down to 1250 (1523K) at cooling rate of 5K/min, the crystal growth is consistent with Ostwald coarsening grew up law, and controlled by diffusion of particle.

Jan 1, 2016